mirror of https://github.com/YosysHQ/yosys.git
137 lines
2.9 KiB
Verilog
137 lines
2.9 KiB
Verilog
|
|
//Cells still in this file have INCOMPLETE simulation models, need to finish them
|
|
|
|
module GP_DCMP(input[7:0] INP, input[7:0] INN, input CLK, input PWRDN, output reg GREATER, output reg EQUAL);
|
|
parameter PWRDN_SYNC = 1'b0;
|
|
parameter CLK_EDGE = "RISING";
|
|
parameter GREATER_OR_EQUAL = 1'b0;
|
|
|
|
//TODO implement power-down mode
|
|
|
|
initial GREATER = 0;
|
|
initial EQUAL = 0;
|
|
|
|
wire clk_minv = (CLK_EDGE == "RISING") ? CLK : ~CLK;
|
|
always @(posedge clk_minv) begin
|
|
if(GREATER_OR_EQUAL)
|
|
GREATER <= (INP >= INN);
|
|
else
|
|
GREATER <= (INP > INN);
|
|
|
|
EQUAL <= (INP == INN);
|
|
end
|
|
|
|
endmodule
|
|
|
|
module GP_EDGEDET(input IN, output reg OUT);
|
|
|
|
parameter EDGE_DIRECTION = "RISING";
|
|
parameter DELAY_STEPS = 1;
|
|
parameter GLITCH_FILTER = 0;
|
|
|
|
//not implemented for simulation
|
|
|
|
endmodule
|
|
|
|
module GP_RCOSC(input PWRDN, output reg CLKOUT_HARDIP, output reg CLKOUT_FABRIC);
|
|
|
|
parameter PWRDN_EN = 0;
|
|
parameter AUTO_PWRDN = 0;
|
|
parameter HARDIP_DIV = 1;
|
|
parameter FABRIC_DIV = 1;
|
|
parameter OSC_FREQ = "25k";
|
|
|
|
initial CLKOUT_HARDIP = 0;
|
|
initial CLKOUT_FABRIC = 0;
|
|
|
|
//output dividers not implemented for simulation
|
|
//auto powerdown not implemented for simulation
|
|
|
|
always begin
|
|
if(PWRDN) begin
|
|
CLKOUT_HARDIP = 0;
|
|
CLKOUT_FABRIC = 0;
|
|
end
|
|
else begin
|
|
|
|
if(OSC_FREQ == "25k") begin
|
|
//half period of 25 kHz
|
|
#20000;
|
|
end
|
|
|
|
else begin
|
|
//half period of 2 MHz
|
|
#250;
|
|
end
|
|
|
|
CLKOUT_HARDIP = ~CLKOUT_HARDIP;
|
|
CLKOUT_FABRIC = ~CLKOUT_FABRIC;
|
|
end
|
|
end
|
|
|
|
endmodule
|
|
|
|
module GP_RINGOSC(input PWRDN, output reg CLKOUT_HARDIP, output reg CLKOUT_FABRIC);
|
|
|
|
parameter PWRDN_EN = 0;
|
|
parameter AUTO_PWRDN = 0;
|
|
parameter HARDIP_DIV = 1;
|
|
parameter FABRIC_DIV = 1;
|
|
|
|
initial CLKOUT_HARDIP = 0;
|
|
initial CLKOUT_FABRIC = 0;
|
|
|
|
//output dividers not implemented for simulation
|
|
//auto powerdown not implemented for simulation
|
|
|
|
always begin
|
|
if(PWRDN) begin
|
|
CLKOUT_HARDIP = 0;
|
|
CLKOUT_FABRIC = 0;
|
|
end
|
|
else begin
|
|
//half period of 27 MHz
|
|
#18.518;
|
|
CLKOUT_HARDIP = ~CLKOUT_HARDIP;
|
|
CLKOUT_FABRIC = ~CLKOUT_FABRIC;
|
|
end
|
|
end
|
|
|
|
endmodule
|
|
|
|
module GP_SPI(
|
|
input SCK,
|
|
inout SDAT,
|
|
input CSN,
|
|
input[7:0] TXD_HIGH,
|
|
input[7:0] TXD_LOW,
|
|
output reg[7:0] RXD_HIGH,
|
|
output reg[7:0] RXD_LOW,
|
|
output reg INT);
|
|
|
|
initial RXD_HIGH = 0;
|
|
initial RXD_LOW = 0;
|
|
initial INT = 0;
|
|
|
|
parameter DATA_WIDTH = 8; //byte or word width
|
|
parameter SPI_CPHA = 0; //SPI clock phase
|
|
parameter SPI_CPOL = 0; //SPI clock polarity
|
|
parameter DIRECTION = "INPUT"; //SPI data direction (either input to chip or output to host)
|
|
//parallel output to fabric not yet implemented
|
|
|
|
//TODO: write sim model
|
|
//TODO: SPI SDIO control... can we use ADC output while SPI is input??
|
|
//TODO: clock sync
|
|
|
|
endmodule
|
|
|
|
//keep constraint needed to prevent optimization since we have no outputs
|
|
(* keep *)
|
|
module GP_SYSRESET(input RST);
|
|
parameter RESET_MODE = "EDGE";
|
|
parameter EDGE_SPEED = 4;
|
|
|
|
//cannot simulate whole system reset
|
|
|
|
endmodule
|