module GP_DFFS(input D, CLK, nSET, output reg Q);
	parameter [0:0] INIT = 1'bx;
	GP_DFFSR #(
		.INIT(INIT),
		.SRMODE(1'b1),
	) _TECHMAP_REPLACE_ (
		.D(D),
		.CLK(CLK),
		.nSR(nSET),
		.Q(Q)
	);
endmodule

module GP_DFFR(input D, CLK, nRST, output reg Q);
	parameter [0:0] INIT = 1'bx;
	GP_DFFSR #(
		.INIT(INIT),
		.SRMODE(1'b0),
	) _TECHMAP_REPLACE_ (
		.D(D),
		.CLK(CLK),
		.nSR(nRST),
		.Q(Q)
	);
endmodule

module GP_DFFSI(input D, CLK, nSET, output reg nQ);
	parameter [0:0] INIT = 1'bx;
	GP_DFFSRI #(
		.INIT(INIT),
		.SRMODE(1'b1),
	) _TECHMAP_REPLACE_ (
		.D(D),
		.CLK(CLK),
		.nSR(nSET),
		.nQ(nQ)
	);
endmodule

module GP_DFFRI(input D, CLK, nRST, output reg nQ);
	parameter [0:0] INIT = 1'bx;
	GP_DFFSRI #(
		.INIT(INIT),
		.SRMODE(1'b0),
	) _TECHMAP_REPLACE_ (
		.D(D),
		.CLK(CLK),
		.nSR(nRST),
		.nQ(nQ)
	);
endmodule

module GP_DLATCHS(input D, nCLK, nSET, output reg Q);
	parameter [0:0] INIT = 1'bx;
	GP_DLATCHSR #(
		.INIT(INIT),
		.SRMODE(1'b1),
	) _TECHMAP_REPLACE_ (
		.D(D),
		.nCLK(nCLK),
		.nSR(nSET),
		.Q(Q)
	);
endmodule

module GP_DLATCHR(input D, nCLK, nRST, output reg Q);
	parameter [0:0] INIT = 1'bx;
	GP_DLATCHSR #(
		.INIT(INIT),
		.SRMODE(1'b0),
	) _TECHMAP_REPLACE_ (
		.D(D),
		.nCLK(nCLK),
		.nSR(nRST),
		.Q(Q)
	);
endmodule

module GP_DLATCHSI(input D, nCLK, nSET, output reg nQ);
	parameter [0:0] INIT = 1'bx;
	GP_DLATCHSRI #(
		.INIT(INIT),
		.SRMODE(1'b1),
	) _TECHMAP_REPLACE_ (
		.D(D),
		.nCLK(nCLK),
		.nSR(nSET),
		.nQ(nQ)
	);
endmodule

module GP_DLATCHRI(input D, nCLK, nRST, output reg nQ);
	parameter [0:0] INIT = 1'bx;
	GP_DLATCHSRI #(
		.INIT(INIT),
		.SRMODE(1'b0),
	) _TECHMAP_REPLACE_ (
		.D(D),
		.nCLK(nCLK),
		.nSR(nRST),
		.nQ(nQ)
	);
endmodule

module GP_OBUFT(input IN, input OE, output OUT);
	GP_IOBUF _TECHMAP_REPLACE_ (
		.IN(IN),
		.OE(OE),
		.IO(OUT),
		.OUT()
	);
endmodule

module \$lut (A, Y);
  parameter WIDTH = 0;
  parameter LUT = 0;

  input [WIDTH-1:0] A;
  output Y;

  generate
    if (WIDTH == 1) begin
		if(LUT == 2'b01) begin
			GP_INV _TECHMAP_REPLACE_ (.OUT(Y), .IN(A[0]) );
		end
		else begin
			GP_2LUT #(.INIT({2'b00, LUT})) _TECHMAP_REPLACE_ (.OUT(Y),
				.IN0(A[0]), .IN1(1'b0));
		end
    end else
    if (WIDTH == 2) begin
      GP_2LUT #(.INIT(LUT)) _TECHMAP_REPLACE_ (.OUT(Y),
      	.IN0(A[0]), .IN1(A[1]));
    end else
    if (WIDTH == 3) begin
      GP_3LUT #(.INIT(LUT)) _TECHMAP_REPLACE_ (.OUT(Y),
      	.IN0(A[0]), .IN1(A[1]), .IN2(A[2]));
    end else
    if (WIDTH == 4) begin
      GP_4LUT #(.INIT(LUT)) _TECHMAP_REPLACE_ (.OUT(Y),
      	.IN0(A[0]), .IN1(A[1]), .IN2(A[2]), .IN3(A[3]));
    end else begin
      wire _TECHMAP_FAIL_ = 1;
    end
  endgenerate
endmodule

module \$__COUNT_ (CE, CLK, OUT, POUT, RST, UP);

	input wire CE;
	input wire CLK;
	output reg OUT;
	output reg[WIDTH-1:0] POUT;
	input wire RST;
	input wire UP;

	parameter COUNT_TO = 1;
	parameter RESET_MODE = "RISING";
	parameter HAS_POUT = 0;
	parameter HAS_CE = 0;
	parameter WIDTH = 8;
	parameter DIRECTION = "DOWN";

	//If we have a CE, or DIRECTION other than DOWN fail... GP_COUNTx_ADV is not supported yet
	if(HAS_CE || (DIRECTION != "DOWN") ) begin
		initial begin
			$display("ERROR: \$__COUNT__ support for GP_COUNTx_ADV is not yet implemented. This counter should never have been extracted (bug in extract_counter pass?).");
			$finish;
		end
	end

	//If counter is more than 14 bits wide, complain (also shouldn't happen)
	else if(WIDTH > 14) begin
		initial begin
			$display("ERROR: \$__COUNT__ support for cascaded counters is not yet implemented. This counter should never have been extracted (bug in extract_counter pass?).");
			$finish;
		end
	end

	//If counter is more than 8 bits wide and has parallel output, we have a problem
	else if(WIDTH > 8 && HAS_POUT) begin
		initial begin
			$display("ERROR: \$__COUNT__ support for 9-14 bit counters with parallel output is not yet implemented. This counter should never have been extracted (bug in extract_counter pass?).");
			$finish;
		end
	end

	//Looks like a legal counter! Do something with it
	else if(WIDTH <= 8) begin
		GP_COUNT8 #(
			.COUNT_TO(COUNT_TO),
			.RESET_MODE(RESET_MODE),
			.CLKIN_DIVIDE(1)
		) _TECHMAP_REPLACE_ (
			.CLK(CLK),
			.RST(RST),
			.OUT(OUT),
			.POUT(POUT)
		);
	end

	else begin
		GP_COUNT14 #(
			.COUNT_TO(COUNT_TO),
			.RESET_MODE(RESET_MODE),
			.CLKIN_DIVIDE(1)
		) _TECHMAP_REPLACE_ (
			.CLK(CLK),
			.RST(RST),
			.OUT(OUT)
		);
	end

endmodule