This adds support for `$check` cells in chformal and adds a `-lower`
mode which converts `$check` cells into `$assert` etc. cells with a
`$print` cell to output the `$check` message.
* Speed up the autoname pass by 2x. This is accomplished by only constructing IdString objects for plain strings that have a higher score.
* Defer creating IdStrings even further. This increases the speedup to 3x.
This does not correctly handle an `$overwrite_tag` on a module output,
but since we currently require the user to flatten the design for
cross-module dft, this cannot be observed from within the design, only
by manually inspecting the signals in the design.
This is still missing a mode to rewrite $overwrite_tag and $original_tag
by injecting $set_tag and $get_tag in the right places. It's also
missing bit-precise propagation models for shifts and arithmetic and
requires the design to be flattened.
* Fixes a non-deterministic polarity error for $eqx/$nex cells
* Fixes a deterministic polarity error for $_NOR_ and $_ORNOT_ cells
* Generates hdlnames when xprop is run after flatten
This makes clk2fflogic add an attr to $ff cells that carry the state of
the emulated async FF. The $ff output doesn't have any async updates
that happened in the current cycle, but the $ff input does, so the $ff
input corresponds to the async FF's output in the original design.
Hence this patch also makes the following changes to passes besides
clk2fflogic (but only for FFs with the clk2fflogic attr set):
* opt_clean treats the input as a register name (instead of the
output)
* rename -witness ensures that the input has a public name
* the formal backends (smt2, btor, aiger) will use the input's
name for the initial state of the FF in witness files
* when sim reads a yw witness that assigns an initial value to the
input signal, the state update is redirected to the output
This ensures that yosys witness files for clk2fflogic designs have
useful and stable public signal names. It also makes it possible to
simulate a clk2fflogic witness on the original design (with some
limitations when the original design is already using $ff cells).
It might seem like setting the output of a clk2fflogic FF to update the
input's initial value might not work in general, but it works fine for
these reasons:
* Witnesses for FFs are only present in the initial cycle, so we do
not care about any later cycles.
* The logic that clk2fflogic generates loops the output of the
genreated FF back to the input, with muxes in between to apply any
edge or level sensitive updates. So when there are no active updates
in the current gclk cycle, there is a combinational path from the
output back to the input.
* The logic clk2fflogic generates makes sure that an edge sensitive
update cannot be active in the first cycle (i.e. the past initial
value is assumed to be whatever it needs to be to avoid an edge).
* When a level sensitive update is active in the first gclk cycle, it
is actively driving the output for the whole gclk cycle, so ignoring
any witness initialization is the correct behavior.
This was renaming cells while iterating over them which would always
cause an assertion failure. Apparently having to rename cells to make
all witness signals public is rarely required, so this slipped through.
In two places, we are joining label pieces by a '|' separator. We go
about it by putting the separator behind each entry, then removing the
trailing separator in a final fixup pass on the built string. For easier
reading, replace those occurrences by a new factored-out
'join_label_pieces' function.
Signed-off-by: Martin Povišer <povik@cutebit.org>
When the 'show' pass generates portboxes to detail the connection of
cell ports to wires, it has special handling of signal chunk
repetitions, but those repetitions are not accounted for in the
displayed bit range in case of cell outputs. Fix that, and so bring it
into consistence with the behavior on cell inputs.
So, taking for example the following Verilog snippet,
module DRIVER (Q);
output [7:0] Q;
assign Q = 8'b10101010;
endmodule
module main;
wire w;
DRIVER driver(.Q({8{w}}));
endmodule
make the show pass display '7:0 - 8x 0:0' in the driver-to-w portbox
instead of '7:7 - 8x 0:0' which it displayed formerly.
Signed-off-by: Martin Povišer <povik@cutebit.org>
This adds the xprop_decoder attribute to bwmuxes that drive the original
unencoded signals. Setundef is changed to ignore the x inputs of these
bwmuxes, so that they survive the prep script of SBY's formal flow. This
is required to make simulation (via sim) using the prep model show the
decoded x signals instead of 0/1 values made up by the solver.
Uses the regex below to search (using vscode):
^\t\tlog\("(.{10,}(?<!\\n)|.{81,}\\n)"\);
Finds any log messages double indented (which help messages are)
and checks if *either* there are is no newline character at the end,
*or* the number of characters before the newline is more than 80.
These can be used to protect undefined flip-flop initialization values
from optimizations that are not sound for formal verification and can
help mapping all solver-provided values in witness traces for flows that
use different backends simultaneously.
Both of these options consider a selection containing only empty modules
as non-empty. This wasn't mentioned in the documentation nor did the
error message when using `select -assert-none` list those empty modules,
which produced a very confusing error message complaining about a
non-empty selection followed by an empty listing of the selection.
This fixes the documentation and changes the `-assert-none` and
`-assert-any` assertion error messages to also output fully selected
modules (this includes selected empty modules).
It doesn't change the messages for `-assert-count` etc. as they don't
count modules.
Jannis Harder
Martin Povišer
Claire Xenia Wolf
Stephen Tong
N. Engelhardt
Lofty
Marcus Comstedt
Rasmus Munk Larsen
Miodrag Milanović
Aki Van Ness
gatecat
Peter Gadfort
KrystalDelusion
Kamyar Mohajerani
KrystalDelusion
Aki Van Ness
George Rennie
bfg86
Marcelina Kościelnicka
Catherine