Group the reconnections, so that instead of producing
connect $auto$wreduce.cc:455:run$24 [0] 1'0
connect $auto$wreduce.cc:455:run$23 [31] 1'0
connect $auto$wreduce.cc:455:run$23 [30] 1'0
... (40 more lines)
we produce
connect $auto$wreduce.cc:461:run$23 [31:11] 21'000000000000000000000
connect $auto$wreduce.cc:461:run$24 [31:10] 22'0000000000000000000000
.
The previous implementation for finding the end of a top-level s-expr
exhibited quadratic behavior as it would re-scan the complete input for
the current expression for every new line. For large designs with
trivial properties this could easily take seconds and dominate the
runtime over the actual solving.
This change remembers the current nesting level between lines, avoiding
the re-scanning.
If the `$ge` cell we are replacing has wide output port, the upper bits
on the port should be driven to zero. That's not what a `$not` cell with
a single-bit input does. Instead opt for a `$logic_not` cell, which does
zero-pad its output.
Fixes#3867.
Extend the aigmap.ys test with SAT-based comparison of the original
cells and their AIG implementations.
This tests both the usual cells and the single-bit Yosys gates.
The guard is optimised out on some compilers under certain conditions (eg: LTO on GCC) as constant under C++ lifetime rules.
This is because the guard type's member is invalid to access (UB) after the type has been destroyed, resulting in
`destruct_guard.ok` being unable to be `false` according to the optimiser, based on the lifetime rules.
This patch still invokes UB (all accesses to the destroyed IdString instance are), but at least the optimiser
can't reason that destruct_guard_ok cannot be false and therefore it's safe to optimise out from its guard role.
C does not guarantee that stdout/stderr can be reassigned.
Most platforms do make them assignable, however musl and WASI that
is based on musl do not. WASI does not have `dup2()`; instead it has
its own non-portable version of it that can only assign to previously
allocated fds.
Update the stream redirection code so that it does the right thing
on WASI and other platforms.
This is mostly important for YoWASP builds, since those do not have
a way to build with external ABC (I prototyped it but for some reason
ABC always segfaults when built as an independent Wasm binary...)
The correct way of using the 'at_zero' regime of simplify is to perform
the simplification on a cloned AST subtree, otherwise the "at_zero"
evaluation seeps into the main tree.
Move the effect of the 'at_zero' flag to the cloning itself, so that
the simplify flag can be retired. We assume we can rely on id2ast in
the new clone method.
It's a repeating pattern to print an error message tied to an AST
node. Start using an 'input_error' helper for that. Among other
things this is beneficial in shortening the print lines, which tend
to be long.
Distinguish between the A, B input ports of `$_ANDNOT_`, `$_ORNOT_`
gates when considering those for sharing. Unlike the input ports of the
other supported single-bit gates, those are not interchangeable.
Fixes#3848.
Later in the check() code we check the bottom wide_log2 bits on the
address port are zeroed out. If the address port is too narrow, we crash
due to out of bounds access. Explicitly assert the address port is wide
enough, so we don't crash on input such as
read_rtlil <<EOF
module \top
wire input 1 \clk
memory width 8 size 2 \mem
cell $memwr $auto$:1:$8
parameter \PRIORITY 1'0
parameter \CLK_POLARITY 1'1
parameter \CLK_ENABLE 1'1
parameter \MEMID "\\mem"
parameter \ABITS 1'0
parameter \WIDTH 6'010000
connect \DATA 16'0000000000000000
connect \ADDR { }
connect \EN 16'0000000000000000
connect \CLK \clk
end
end
EOF
memory
whitequark
github-actions[bot]
Miodrag Milanovic
Martin Povišer
Jannis Harder
dragonmux
N. Engelhardt
Zachary Snow
Dag Lem