Add new tests.

tests/ice40/alu.v

@@ -0,0 +1,19 @@
+module top (
+	input clock,
+	input [31:0] dinA, dinB,
+	input [2:0] opcode,
+	output reg [31:0] dout
+);
+	always @(posedge clock) begin
+		case (opcode)
+		0: dout <= dinA + dinB;
+		1: dout <= dinA - dinB;
+		2: dout <= dinA >> dinB;
+		3: dout <= $signed(dinA) >>> dinB;
+		4: dout <= dinA << dinB;
+		5: dout <= dinA & dinB;
+		6: dout <= dinA | dinB;
+		7: dout <= dinA ^ dinB;
+		endcase
+	end
+endmodule

tests/ice40/alu.ys

@@ -0,0 +1,11 @@
+read_verilog alu.v
+hierarchy -top top
+proc
+flatten
+equiv_opt -assert -map +/ice40/cells_sim.v synth_ice40 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+select -assert-count 62 t:SB_CARRY
+select -assert-count 32 t:SB_DFF
+select -assert-count 655 t:SB_LUT4
+select -assert-none t:SB_CARRY t:SB_DFF t:SB_LUT4 %% t:* %D

tests/ice40/counter.v

@@ -0,0 +1,17 @@
+module top    (
+out,
+clk,
+reset
+);
+    output [7:0] out;
+    input clk, reset;
+    reg [7:0] out;
+
+    always @(posedge clk, posedge reset)
+		if (reset) begin
+			out <= 8'b0 ;
+		end else
+			out <= out + 1;
+
+
+endmodule

tests/ice40/counter.ys

@@ -0,0 +1,11 @@
+read_verilog counter.v
+hierarchy -top top
+proc
+flatten
+equiv_opt -map +/ice40/cells_sim.v synth_ice40 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+select -assert-count 7 t:SB_CARRY
+select -assert-count 8 t:SB_DFFR
+select -assert-count 8 t:SB_LUT4
+select -assert-none t:SB_CARRY t:SB_DFFR t:SB_LUT4 %% t:* %D

tests/ice40/fsm.v

@@ -0,0 +1,73 @@
+ module fsm (
+ clock,
+ reset,
+ req_0,
+ req_1,
+ gnt_0,
+ gnt_1
+ );
+ input   clock,reset,req_0,req_1;
+ output  gnt_0,gnt_1;
+ wire    clock,reset,req_0,req_1;
+ reg     gnt_0,gnt_1;
+
+ parameter SIZE = 3           ;
+ parameter IDLE  = 3'b001,GNT0 = 3'b010,GNT1 = 3'b100,GNT2 = 3'b101 ;
+
+ reg [SIZE-1:0] state;
+ reg [SIZE-1:0] next_state;
+
+ always @ (posedge clock)
+ begin : FSM
+ if (reset == 1'b1) begin
+   state <=  #1  IDLE;
+   gnt_0 <= 0;
+   gnt_1 <= 0;
+ end else
+  case(state)
+    IDLE : if (req_0 == 1'b1) begin
+                 state <=  #1  GNT0;
+                 gnt_0 <= 1;
+               end else if (req_1 == 1'b1) begin
+                 gnt_1 <= 1;
+                 state <=  #1  GNT0;
+               end else begin
+                 state <=  #1  IDLE;
+               end
+    GNT0 : if (req_0 == 1'b1) begin
+                 state <=  #1  GNT0;
+               end else begin
+                 gnt_0 <= 0;
+                 state <=  #1  IDLE;
+               end
+    GNT1 : if (req_1 == 1'b1) begin
+                 state <=  #1  GNT2;
+				 gnt_1 <= req_0;
+               end
+    GNT2 : if (req_0 == 1'b1) begin
+                 state <=  #1  GNT1;
+				 gnt_1 <= req_1;
+               end
+    default : state <=  #1  IDLE;
+ endcase
+ end
+
+ endmodule
+
+ module top (
+input clk,
+input rst,
+input a,
+input b,
+output g0,
+output g1
+);
+
+fsm u_fsm ( .clock(clk),
+            .reset(rst),
+            .req_0(a),
+            .req_1(b),
+            .gnt_0(g0),
+            .gnt_1(g1));
+
+endmodule

tests/ice40/fsm.ys

@@ -0,0 +1,13 @@
+read_verilog fsm.v
+hierarchy -top top
+proc
+flatten
+equiv_opt -assert -map +/ice40/cells_sim.v synth_ice40 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+
+select -assert-count 2 t:SB_DFFESR
+select -assert-count 2 t:SB_DFFSR
+select -assert-count 1 t:SB_DFFSS
+select -assert-count 13 t:SB_LUT4
+select -assert-none t:SB_DFFESR t:SB_DFFSR t:SB_DFFSS t:SB_LUT4 %% t:* %D

tests/ice40/logic.v

@@ -0,0 +1,18 @@
+module top
+(
+ input [0:7] in,
+ output B1,B2,B3,B4,B5,B6,B7,B8,B9,B10
+ );
+
+   assign     B1 =  in[0] & in[1];
+   assign     B2 =  in[0] | in[1];
+   assign     B3 =  in[0] ~& in[1];
+   assign     B4 =  in[0] ~| in[1];
+   assign     B5 =  in[0] ^ in[1];
+   assign     B6 =  in[0] ~^ in[1];
+   assign     B7 =  ~in[0];
+   assign     B8 =  in[0];
+   assign     B9 =  in[0:1] && in [2:3];
+   assign     B10 =  in[0:1] || in [2:3];
+
+endmodule

tests/ice40/logic.ys

@@ -0,0 +1,7 @@
+read_verilog logic.v
+hierarchy -top top
+equiv_opt -assert -map +/ice40/cells_sim.v synth_ice40 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+select -assert-count 9 t:SB_LUT4
+select -assert-none t:SB_LUT4 %% t:* %D

tests/ice40/shifter.v

@@ -0,0 +1,22 @@
+module top    (
+out,
+clk,
+in
+);
+    output [7:0] out;
+    input signed clk, in;
+    reg signed [7:0] out = 0;
+
+    always @(posedge clk)
+	begin
+`ifndef BUG
+		out    <= out >> 1;
+		out[7] <= in;
+`else
+
+		out    <= out << 1;
+		out[7] <= in;
+`endif
+	end
+
+endmodule

tests/ice40/shifter.ys

@@ -0,0 +1,9 @@
+read_verilog shifter.v
+hierarchy -top top
+proc
+flatten
+equiv_opt -assert -map +/ice40/cells_sim.v synth_ice40 # equivalency check
+design -load postopt # load the post-opt design (otherwise equiv_opt loads the pre-opt design)
+cd top # Constrain all select calls below inside the top module
+select -assert-count 8 t:SB_DFF
+select -assert-none t:SB_DFF %% t:* %D