Progress in presentation

manual/PRESENTATION_ExAdv.tex

@@ -259,7 +259,7 @@ Generate blocks and recursion are powerful tools for writing map files.
 \end{itemize}
 \end{frame}
 
-\begin{frame}[t]{\subsubsecname -- Example 1/2}
+\begin{frame}[t]{\subsubsecname{} -- Example 1/2}
 \vskip-0.2cm
 To map the Verilog OR-reduction operator to 3-input OR gates:
 \vskip-0.2cm
@@ -271,7 +271,7 @@ To map the Verilog OR-reduction operator to 3-input OR gates:
 \end{columns}
 \end{frame}
 
-\begin{frame}[t]{\subsubsecname -- Example 2/2}
+\begin{frame}[t]{\subsubsecname{} -- Example 2/2}
 \vbox to 0cm{
 \hfil\includegraphics[width=10cm,trim=0 0cm 0 0cm]{PRESENTATION_ExAdv/red_or3x1.pdf}
 \vss
@@ -284,6 +284,42 @@ To map the Verilog OR-reduction operator to 3-input OR gates:
 \end{columns}
 \end{frame}
 
+\subsubsection{Conditional techmap}
+
+\begin{frame}{\subsubsecname}
+\begin{itemize}
+\item In some cases only cells with certain properties should be substituted.
+\medskip
+\item The special wire {\tt \_TECHMAP\_FAIL\_} can be used to disable a module
+in the map file for a certain set of parameters.
+\medskip
+\item The wire {\tt \_TECHMAP\_FAIL\_} must be set to a constant value. If it
+is non-zero then the module is disabled for this set of parameters.
+\medskip
+\item Example use-cases:
+\begin{itemize}
+\item coarse-grain cell types that only operate on certain bit widths
+\item memory resources for different memory geometries (width, depth, ports, etc.)
+\end{itemize}
+\end{itemize}
+\end{frame}
+
+\begin{frame}[t]{\subsubsecname{} -- Example}
+\vbox to 0cm{
+\vskip-0.5cm
+\hfill\includegraphics[width=6cm,trim=0 0cm 0 0cm]{PRESENTATION_ExAdv/sym_mul.pdf}
+\vss
+}
+\vskip-0.5cm
+\lstinputlisting[basicstyle=\ttfamily\fontsize{8pt}{10pt}\selectfont, language=verilog]{PRESENTATION_ExAdv/sym_mul_map.v}
+\begin{columns}
+\column[t]{6cm}
+\vskip-0.5cm\lstinputlisting[basicstyle=\ttfamily\fontsize{8pt}{10pt}\selectfont, frame=single, language=verilog]{PRESENTATION_ExAdv/sym_mul_test.v}
+\column[t]{4cm}
+\vskip-0.5cm\lstinputlisting[basicstyle=\ttfamily\fontsize{8pt}{10pt}\selectfont, frame=single, language=ys, lastline=4]{PRESENTATION_ExAdv/sym_mul_test.ys}
+\end{columns}
+\end{frame}
+
 \subsubsection{TBD}
 
 \begin{frame}{\subsubsecname}

manual/PRESENTATION_ExAdv/Makefile

@@ -1,5 +1,5 @@
 
-all: select_01.pdf red_or3x1.pdf
+all: select_01.pdf red_or3x1.pdf sym_mul.pdf
 
 select_01.pdf: select_01.v select_01.ys
 	../../yosys select_01.ys
@@ -7,3 +7,6 @@ select_01.pdf: select_01.v select_01.ys
 red_or3x1.pdf: red_or3x1_*
 	../../yosys red_or3x1_test.ys
 
+sym_mul.pdf: sym_mul_*
+	../../yosys sym_mul_test.ys
+

manual/PRESENTATION_ExAdv/sym_mul_cells.v

@@ -0,0 +1,6 @@
+module MYMUL(A, B, Y);
+    parameter WIDTH = 1;
+    input [WIDTH-1:0] A, B;
+    output [WIDTH-1:0] Y;
+    assign Y = A * B;
+endmodule

manual/PRESENTATION_ExAdv/sym_mul_map.v

@@ -0,0 +1,15 @@
+module \$mul (A, B, Y);
+    parameter A_SIGNED = 0;
+    parameter B_SIGNED = 0;
+    parameter A_WIDTH = 1;
+    parameter B_WIDTH = 1;
+    parameter Y_WIDTH = 1;
+    
+    input [A_WIDTH-1:0] A;
+    input [B_WIDTH-1:0] B;
+    output [Y_WIDTH-1:0] Y;
+    
+    wire _TECHMAP_FAIL_ = A_WIDTH != B_WIDTH || B_WIDTH != Y_WIDTH;
+    
+    MYMUL #( .WIDTH(Y_WIDTH) ) g ( .A(A), .B(B), .Y(Y) );
+endmodule

manual/PRESENTATION_ExAdv/sym_mul_test.v

@@ -0,0 +1,5 @@
+module test(A, B, C, Y1, Y2);
+    input   [7:0] A, B, C;
+    output  [7:0] Y1 = A * B;
+    output [15:0] Y2 = A * C;
+endmodule

manual/PRESENTATION_ExAdv/sym_mul_test.ys

@@ -0,0 +1,6 @@
+read_verilog sym_mul_test.v
+hierarchy -check -top test
+
+techmap -map sym_mul_map.v;;
+
+show -prefix sym_mul -format pdf -notitle -lib sym_mul_cells.v