347 lines
19 KiB
C++
347 lines
19 KiB
C++
|
|
// -*- C++ -*-
|
|
|
|
namespace Anabatic {
|
|
|
|
/*! \defgroup LoadGlobalRouting Global Routing Loading
|
|
* \brief Translation rules to build detailed routing from global
|
|
*
|
|
* This module documents how the global routing built by \c Knik is
|
|
* loaded into the \c Anabatic data-base. It is intented for developpers
|
|
* only.
|
|
*/
|
|
|
|
//! \addtogroup LoadGlobalRouting
|
|
//! \{
|
|
|
|
//! \enum LocalFunctionFlag
|
|
//! A set of flags for all functions of the LoadGlobalRouting module.
|
|
//! They can be combined to form the \e flags argument of functions.
|
|
//! the functions will ignore flags that are not intended to them.
|
|
//!
|
|
//! For \c HSmall, \c VSmall & \c Punctual see checkRoutingPadSize().
|
|
|
|
//! \var LocalFunctionFlag::NoFlags
|
|
//! A simple alias over zero to explicitly tell that no flag at all is
|
|
//! passed to the function.
|
|
|
|
//! \var LocalFunctionFlag::HAccess
|
|
//! The constructed topology will be accessed through an horizontal
|
|
//! segment. The absence of this flag tell that the access will be done
|
|
//! trough a vertical.
|
|
|
|
//! \var LocalFunctionFlag::VSmall
|
|
//! The RoutingPad vertically covers a very small number of access points,
|
|
//! so it is likely overconstrained for direct horizontal connexion.
|
|
|
|
//! \var LocalFunctionFlag::HSmall
|
|
//! The RoutingPad horizontally covers a very small number of access points,
|
|
//! so it is likely overconstrained for direct vertical connexion.
|
|
|
|
//! \var LocalFunctionFlag::Punctual
|
|
//! The RoutingPad covers only an access point in either direction.
|
|
|
|
//! \var LocalFunctionFlag::DoSourceContact
|
|
//! When creating Anabatic::AutoContactTerminal on non-punctual RoutingPad, this flag
|
|
//! request the creation of a contact <em>on the source point</em>.
|
|
|
|
//! \var LocalFunctionFlag::DoTargetContact
|
|
//! When creating Anabatic::AutoContactTerminal on non-punctual RoutingPad, this flag
|
|
//! request the creation of a contact <em>on the target point</em>.
|
|
|
|
|
|
//! \function uint64_t checkRoutingPadSize ( Component* rp );
|
|
//!
|
|
//! Look at the geometrical size of the Component and assess if
|
|
//! it's span is too narrow either horizontally or vertically.
|
|
//! Return a combination of flags indicating it's state:
|
|
//! - HSmall : less than 3 pitches in horizontal direction.
|
|
//! - VSmall : less than 3 pitches in vertical direction.
|
|
//! - Punctual : one pitch in either directions.
|
|
//!
|
|
//! The component can be a RoutingPad, a Vertical or an Horizontal.
|
|
//!
|
|
//! \image html checkRoutingPadSize.png "checkRoutingPadSize()"
|
|
|
|
/*! \class NetBuilder
|
|
*
|
|
* \brief Build the wiring for a Net inside a GCell (\b internal).
|
|
*
|
|
* As this class is called to initially construct the Anabatic wiring,
|
|
* it must build a \b connex wiring. That is without gaps in layer depth,
|
|
* because the topology restauration mechanism (AutoContact::updateTopology())
|
|
* of the AutoContact cannot work until all AutoSegments are revalidated at
|
|
* least once. The topology restauration work by creating doglegs which in turn,
|
|
* call the canonization, which needs all the caches to be up to date.
|
|
*/
|
|
|
|
//! \function void NetBuilder::doRp_AutoContacts ( GCell* gcell, Component* rp, AutoContact*& source, AutoContact*& target, uint64_t flags );
|
|
//! \param gcell The GCell into which create the AutoContact.
|
|
//! \param rp The Component we want to access.
|
|
//! \param source The AutoContact created on the \c source (\e returned).
|
|
//! \param target The AutoContact created on the \c target (\e returned).
|
|
//! \param flags Managed by this function:
|
|
//! - LocalFunctionFlag::DoSourceContact
|
|
//! - LocalFunctionFlag::DoTargetContact
|
|
//!
|
|
//! Create the AutoContact directly anchored on the Component (terminal).
|
|
//! Three cases are manageds:
|
|
//! -# <b>Ordinary (non-punctual) \c METAL1 terminal</b>: an AutoContactTerminal
|
|
//! is anchored on the RoutingPad.
|
|
//! -# <b>Punctual \c METAL1 terminal</b>, the access must never be blocked
|
|
//! by other routing. To ensure it, we create a fixed AutoSegment (anchored
|
|
//! on two AutoContactTerminal) to cover it. The \e normal AutoContactTerminal
|
|
//! is also created.
|
|
//! -# <b>non \c METAL1 terminal</b>, as for the punctual \c METAL1, a
|
|
//! fixed protection is added over the RoutingPad. If we access
|
|
//! horizontally a vertical RoutingPad or vertically an horizontal
|
|
//! one, an extra AutoContactTerminal is added (to allow is displacement
|
|
//! along the RoutingPad).
|
|
//!
|
|
//! To avoid creating a fixed protection over a RoutingPad multiple times,
|
|
//! the RoutingPad and it's associated protection is stored in a static
|
|
//! \c map : \c __routingPadAutoSegments.
|
|
//!
|
|
//! Conversely, because an AutoContactTerminal can only be connected to one
|
|
//! segment, each time this function is called a new terminal will be created
|
|
//! (or maybe two in case of non-punctual terminals). If only one AutoContact
|
|
//! is requested, it is created centered on the RoutingPad. The initial
|
|
//! position of AutoContact <em>do not prevent them to move afterwards</em>,
|
|
//! even those created on source/target on a non-punctual RoutingPad.
|
|
//!
|
|
//! \remark For clarity we describe the layer management of this function in term
|
|
//! of \c METAL, but it is the RoutingGauge depth which is actually used.
|
|
//!
|
|
//! \image html doRp_AutoContacts.png "doRp_AutoContacts()"
|
|
|
|
//! \function AutoContact* NetBuilder::doRp_Access ( GCell* gcell, Component* rp, uint64_t flags );
|
|
//! \param gcell The GCell into which create the AutoContact.
|
|
//! \param rp The Component onto which anchor the access contact.
|
|
//! \param flags Relevant flags are:
|
|
//! - HAccess, the terminal is to be accessed through an horizontal
|
|
//! segment.
|
|
//! - VSmall, force the terminal to be considered as small in the
|
|
//! vertical direction.
|
|
//!
|
|
//! If \c HAccess is set, the Component is to be accessed trough an horizontal
|
|
//! segment. If unset, the access is done vertically.
|
|
//!
|
|
//! Create an AutoContact to access a Component (terminal). If the Component
|
|
//! is not to be accessed through an horizontal segment, and do not cover a
|
|
//! large span in the horizontal direction (flag \c VSmall), a local horizontal
|
|
//! AutoSegment is added to slacken the vertical constraints.
|
|
//!
|
|
//! \image html doRp_Access.png "doRp_Access()"
|
|
|
|
//! \function AutoContact* NetBuilder::doRp_AccessPad ( RoutingPad* rp, uint64_t flags );
|
|
//! \param rp The Component onto which anchor the access contact.
|
|
//! \param flags Relevant flags are:
|
|
//! - HAccess, the terminal is to be accessed through an horizontal
|
|
//! segment.
|
|
//! - VSmall, force the terminal to be considered as small in the
|
|
//! vertical direction.
|
|
//! \return A Anabatic::AutoContactTerminal .
|
|
//!
|
|
//! The Component \c rp is a RoutingPad which belongs to a pad cell. This case
|
|
//! occurs when we are routing a complete chip. This method build, from the
|
|
//! \c rp a stack of articulated punctual segments and contacts to reach the
|
|
//! default H/V routing layers (usually \c METAL2 & \c METAL3). This may be
|
|
//! needed when the pad terminal is in \c METAL5, for instance.
|
|
//!
|
|
//! The returned AutoContactTerminal is anchored on the last punctual segment
|
|
//! build.
|
|
//!
|
|
//! The GCell into which the AutoContactTerminal is created may be under the
|
|
//! pads area. However, it will be right on the border of the GCell.
|
|
//! The global router vertexes of GCell under the pad area are marked as
|
|
//! blocked so will never be used for routing.
|
|
//!
|
|
//! \remark The segments and contacts added to ensure the layer connexity are not
|
|
//! put into the Anabatic database. They are plain Hurricane objects, invisibles
|
|
//! from it.
|
|
|
|
//! \function void NetBuilder::doRp_StairCaseH ( GCell* gcell, Component* rp1, Component* rp2 );
|
|
//!
|
|
//! Build the wiring to connect to horizontal Component. Two cases:
|
|
//! - The Component are aligneds, then only a straight wire is created.
|
|
//! - They are \e not aligned, then a complete dogleg is created.
|
|
//!
|
|
//! \image html doRp_StairCaseH.png "doRp_StairCaseH()"
|
|
|
|
//! \function void NetBuilder::doRp_StairCaseV ( GCell* gcell, Component* rp1, Component* rp2 );
|
|
//!
|
|
//! Build the wiring to connect to vertical Components. Two cases:
|
|
//! - The Components are aligneds, then only a straight wire is created.
|
|
//! - They are \e not aligned, then a complete dogleg is created.
|
|
//!
|
|
//! \image html doRp_StairCaseV.png "doRp_StairCaseV()"
|
|
|
|
//! \function void NetBuilder::_do_xG_1Pad ();
|
|
//!
|
|
//! Construct the topology, when there is only global wires and one local
|
|
//! terminal, but coming from a Pad. As thoses connectors will always be
|
|
//! on one border of the GCell they can be considered as a kind of global.
|
|
//!
|
|
//! So this method mostly calls NetBuilder::doRp_AccessPad() to create
|
|
//! the AutoContactTerminal, then calls NetBuilder::_do_xG(), except
|
|
//! for straight lines which are managed directly.
|
|
|
|
//! \function void NetBuilder::_do_xG ();
|
|
//!
|
|
//! Construct the topology, when there is only global wires (no local terminals).
|
|
//!
|
|
//! Some topology are not handled because they must not be managed by this
|
|
//! function:
|
|
//! <ul>
|
|
//! <li>One global: nonsensical because there also must be a terminal.
|
|
//! <li>Two aligned globals: in that case we do a straight wire whithout
|
|
//! any AutoContact (handled by the source/target of the wire).
|
|
//! </ul>
|
|
//!
|
|
//! \image html _do_xG.png "_do_xG()"
|
|
|
|
//! \function void NetBuilder::_do_1G_1M1 ();
|
|
//!
|
|
//! Construct a topology where there is \e one global and one RoutingPad
|
|
//! in \c METAL1. The \c METAL1 is assumed to be vertical.
|
|
//!
|
|
//! \remark When accessing the RoutingPad through an horizontal global segment
|
|
//! and the vertical extension of the segment is small, the global is
|
|
//! still directly attached to the terminal, inducing a high constraint
|
|
//! on it. We left to job of slackening it to the router.
|
|
//!
|
|
//! \image html _do_1G_1M1.png "_do_1G_1M1()"
|
|
|
|
//! \function void NetBuilder::_do_1G_xM1 ();
|
|
//!
|
|
//! Construct a topology where there is \e one global and any number of
|
|
//! RoutingPad in \c METAL1. The \c METAL1 is assumed to be vertical.
|
|
//!
|
|
//! The RoutingPads are linked together two by two. If the horizontal
|
|
//! segments are not aligned by the router, part of the routage will be
|
|
//! done through the RoutingPad itself. The global incoming segment will
|
|
//! connected to the leftmost, rightmost or centermost RoutingPad according
|
|
//! from wich side it comes from.
|
|
//!
|
|
//! \image html _do_1G_xM1.png "_do_1G_xM1()"
|
|
|
|
//! \function void NetBuilder::_do_xG_1M1_1M2 ();
|
|
//!
|
|
//! Construct a topology where there is at least one global (and up to 4),
|
|
//! one \c METAL1 RoutingPad (assumed V) and one \c METAL2 RoutingPad (assumed H).
|
|
//!
|
|
//! In this topology, we want to try to reuse the \c METAL2 RoutingPad as a
|
|
//! feedtrough in the horizontal routage. Thus:
|
|
//! - The \c METAL1 and \c METAL2 RoutingPad are connected through a separate wiring.
|
|
//! - The south & west global wiring is attached to the leftmost contact of
|
|
//! the \c METAL2.
|
|
//! - The north & east global wiring is attached to the rightmost contact of
|
|
//! the \c METAL2.
|
|
//!
|
|
//! South/west and north/south can be build independantly. Depending on the number
|
|
//! of globals, they can consist of:
|
|
//! - Nothing (no south nor west).
|
|
//! - An AutoContact (west present).
|
|
//! - An horizontal plus a turn (south present).
|
|
//! - An horizontal plus a HTee (south & west present).
|
|
//!
|
|
//! \remark Not all configurations are represented below.
|
|
//!
|
|
//! \image html _do_xG_1M1_1M2.png "_do_xG_1M1_1M2()"
|
|
|
|
//! \function void NetBuilder::_do_xG_xM1_xM3 ();
|
|
//!
|
|
//! Construct a topology where there is at least one global (and up to 4),
|
|
//! at least one \c METAL1 RoutingPad (assumed V) and at least one \c METAL3
|
|
//! RoutingPad (assumed V).
|
|
//!
|
|
//! In this topology, we want to try to reuse the \c METAL3 RoutingPad as a
|
|
//! feedtrough in the vertical routage. Thus:
|
|
//! - The \c METAL1 and \c METAL3 RoutingPad are connected through a separate
|
|
//! wiring made of separate horizontals.
|
|
//! - The south-west global wiring is attached to the leftmost RoutingPad
|
|
//! if there isn't south or to the first \c METAL3 otherwise.
|
|
//! - The north-east global wiring is attached to the rightmost RoutingPad
|
|
//! if there isn't north or to the first \c METAL3 otherwise.
|
|
//!
|
|
//! South/west and north/south can be build independantly. Depending on the number
|
|
//! of globals, they can consist of:
|
|
//! - Nothing (no south nor west).
|
|
//! - An AutoContact on the leftmost RoutingPad (west present).
|
|
//! - An AutoContact on the first \c METAL3 (only south present).
|
|
//! - An AutoContact plus a vertical plus a VTee (south & west present).
|
|
//!
|
|
//! \image html _do_xG_xM1_xM3.png "_do_xG_xM1_xM3()"
|
|
|
|
//! \function void NetBuilder::_do_xG_xM2 ();
|
|
//!
|
|
//! Construct a topology where there is at least one global (and up to 4),
|
|
//! and any number of \c METAL2 RoutingPads (assumeds H).
|
|
//!
|
|
//! In this topology, we want to try to reuse the \c METAL2 RoutingPad as a
|
|
//! feedtrough in the horizontal routage. Thus:
|
|
//! - The RoutingPad are connecteds trough a separate staircase (or
|
|
//! straight wire if aligneds).
|
|
//! - The south-west global wiring is attached to the leftmost RoutingPad
|
|
//! if there isn't south or to the biggest horizontal RoutingPad otherwise.
|
|
//! - The north-east global wiring is attached to the rightmost RoutingPad
|
|
//! if there isn't south or to the biggest horizontal RoutingPad otherwise.
|
|
//!
|
|
//! \image html _do_xG_xM2.png "_do_xG_xM2()"
|
|
|
|
//! \function void NetBuilder::_do_1G_1M3 ();
|
|
//!
|
|
//! Construct a topology where there is one global and one \c METAL3 RoutingPad
|
|
//! (assumeds V).
|
|
//!
|
|
//! In this topology, we reuse the \c METAL3 RoutingPad as a feedtrough in the
|
|
//! vertical routage. Thus:
|
|
//! - If the global is either north or south, we directly connect to the
|
|
//! north end or south end of the RoutingPad. \red{The vertical global will}
|
|
//! \red{have no slack at all we assume that METAL3 terminals are only from}
|
|
//! \red{blocks and are aligneds vertically.}
|
|
//! - If the global is east or west \e and the RoutingPad is sufficiently
|
|
//! extended in the vertical direction, we connect an horizontal in the
|
|
//! normal way.
|
|
//! - If the global is not sufficiently extended, we add a turn to give some
|
|
//! slack to the global.
|
|
//!
|
|
//!
|
|
//! \image html _do_1G_1M3.png "_do_1G_1M3()"
|
|
|
|
//! \function void NetBuilder::_do_xG_xM3 ();
|
|
//!
|
|
//! Construct a topology where there at least one global and two \c METAL3 RoutingPad
|
|
//! (assumed V).
|
|
//!
|
|
//! In this topology, we reuse the \c METAL3 RoutingPad as a feedtrough in the
|
|
//! vertical routage. \red{We assume that the most likely relative position}
|
|
//! \red{of the RoutingPads is to be aligned vertically}.
|
|
//! Thus:
|
|
//! - All RoutingPads are linked two by two trough vertical staircases.
|
|
//! - The south-west global wiring is attached to the bottommost RoutingPad
|
|
//! (without vertical slack). If a misalignment is detected, then a
|
|
//! dogleg is added.
|
|
//! - The north-east global wiring is attached to the topmost RoutingPad
|
|
//! (without vertical slack).
|
|
//!
|
|
//! South/west and north/south can be build independantly. Depending on the number
|
|
//! of globals, they can consist of:
|
|
//! - Nothing (no south nor west).
|
|
//! - An sliding AutoContact on the bottommost RoutingPad (west present).
|
|
//! - An fixed AutoContact on the bottommost RoutingPad (only south present).
|
|
//! - An fixed AutoContact plus a vertical plus a VTee (south & west present).
|
|
//!
|
|
//! \image html _do_xG_xM3.png "_do_xG_xM3()"
|
|
|
|
//! \function void singleGCell ( AnabaticEngine* anbt, Net* net );
|
|
//!
|
|
//! All the RoutingPads of the net are concentrated under a single
|
|
//! GCell. This function assumes that all the terminals are in
|
|
//! \c METAL1 (vertical), and link them two by two by horizontal
|
|
//! wires.
|
|
|
|
//! \}
|
|
|
|
}
|