* New: In Isobar::PyCell, export the isRouted() and setRouted() to the
Python interface.
* Bug: In CRL::Entity::parseEntity(), check that the closing parenthesis
is the last character of the net name. Issue a more relevant error
message.
* In Anabatic::NetBuilder::_do_xG() and all other unimplemented methods,
throw an error if called from a derived classes instead of just
issuing a message in the debug stream. Avoid later core dumps...
* In Anabatic::NetBuilderHV, implement the builders for GCells with
one pin. Needed to support chip/corona routing.
* Bug: In Cumulus/plugins/Chip.py, check that coronaCk exists before
using it.
* New: In Cumulus/plugins/PadsCorona/Side._placePad(), when routing
a design with symbolic pads, export the chip external "pad"
connectors to be able to perform a lvx (otherwise cougar do not
create external nets).
In Corona._createCoreWire(), set the minimal gap between the pads
and the corona to 6 pitches. Empirical value to avoid DRC errors
with symbolic pads (pxlib).
When successufully done, mark the Corona cell as routed.
* Bug: In Cumulus/plugins/Core2Chip.IoNet, the regex for vectorizet net
was wrong, it was allowing only one digit in the index.
* Bug: In Cumulus/plugins/Core2Chip.cmos, correct management of
pad & corona clock nets. Correct connexion between vdde/vddi.
* Bug: In Unicorn/cgt.py, forgot to execute scripts when in text mode.
* Bug: In CRL/etc/symbolic/cmos/plugins.conf, rails dimensions are no
longer expressed directly in lambda. Must be created using helper.l().
* Change: In CRL::ApParser, slightly more smart management of Pin width.
Must normalize Pin behavior between Alliance & Hurricane as in
Alliance they have only one dimension.
* Change: In CRL::LefImport, if a net name end with "!", assume it's a
global one. Have to check this naming convention.
* Change: In Anabatic::NetBuilderHV::_do_1G_1PinM3() & _do_1G_1PinM2()
now implemented. Needed for the corona routing support.
* Change: In AnabaticEngine::setupPreRouted(), exclude segments outside
the abutment box.
* Change: In KatanaEngine::PowerRails, remove the I/O pad support as now
we route only inside the Corona. So only one vdd/vss/ck are supported.
* New: In cumulus/plugins/ChipPlugin.py, complete rewrite of the chip
support:
* Uncouple pad I/O ring whith real cells (foundry) from a symbolic
core. A new intermediate level "corona" is introduced to handle
the real/symbolic transition.
* Ability to explicitly setup position of the pads on the chip side
in case of uneven distribution.
* Enable clock tree to be build with 3 metal only (M2 to M4) instead
of (M2 to M5).
* Bug: In Anabatic::AutoSegment, Anabatic::AutoContact and derived
classes, the recursive invalidation mechanism did have cross-call
troubles.
- The various AutoContact::_invalidate() now take the flag into
account instead of resetting it. This is for Flags::Topology
to be passed along from segments to contacts.
- In AutoSegment::invalidate(), do not invalidate S/T contacts
already invalidateds. In the same way, do not invalidate
aligned segments already invalidateds (save some recursion).
- In AutoSegment::_changeDepth(), call invalidate with
Flags::Topology (to force contact update) and Flags::NoCheckLayer
to avoid disgraceful warnings.
* New: Anabatic::NetBuilder::_do_xG_1M1() with (x >= 2) new set of
optimized topologies when there is multiple globals but only one
terminal. The default one was making two connections to the same
RoutingPad, which was making clutter.
* Change: In Anabatic::AutoContactTerminal::getNativeConstraintBox(),
when the anchor is a RoutingPad (which must be always the case),
perform the true computation of it's position based on the
segment occurrence. It is a important change, previously the
area was in fact the "center line" of the connector while now
it is really an area (mandatory for "half-offgrid" terminals of
real technologies).
The change is not complete yet, the area should be shrinked
by the half size of a VIA, because the area applies to the center
coordinate of the VIA (to be done quickly).
* Bug: In Anabatic::AutoContactTurn::updateTopology(), when a dogleg
is created (restore connexity after a layer change) the layer of
the VIA, based on the segments it connects to must be re-computed
*after* the dogleg has been made.
* Change: In all files of Anabatic, when comparing two layers, no longer
use the Layer pointer itself, but the layer mask. This allow a
transparent management of both real and symbolic layers (which
do share the same mask). Real metal layers (not VIAs) will be
BasicLayer and symbolic metal layers will be RegularLayer.
* New: Anabatic::Configuration::selectRpComponent(), select the best
RoutingPad component for metal1 terminals. Look for the metal1
component with the biggest accessibility on-grid.
RoutingPad using other metals are left untoucheds.
* New: New function Anabatic::Vertex::getNeighbor(Edge*) to get the
neighbor Vertex through an Edge*. This method allows to write
clearer code as we no longer need to access the neighbor through
the underlying GCell.
Also add proxies for GCell methods in Vertex.
* Bug: In Anabatic::Dijkstra::_toSources(), in the ripup stage, when
a component with multiples vertexes is reached *and* two of it's
vertexes are reached *at the same time* (one from which we backtrack
and one still in the queue) extraneous edges may be created by
_materialize(). Case occurs on snx/c35b4, "abc_5360_n903_1".
To solve this, Dijkstra::_toSource() is modificated, the "from"
edges of the newly reacheds vertexes are reset to NULL, *except*
for the one we will be backtracking from. That is, the one given
in the source argument.
* Change: In Anabatic::NetBuilder class, put the various Hooks and
RoutingPad sorting functions as class ones.
* Bug: In AutoSegment::setLayer(), raise the SegInvalidatedFayer flag.
This unset flag was causing AutoContactTurn::updateTopology()
to not work as expected and making gaps, this was the cause of
the last remaining warnings about layer connexity.
* New: In Anabatic::NetBuilder, set all the attributes as private and
create accessors and mutators.
Finish virtualising all GCell build methods and transfer them
into the NetBuilderHV class.
Build methods now return a boolean to tell if the GCell was
processed or not, to allow cascading in the "big switch".
Reorganise the "big switch" in separate sections only partially
cascading.
Truly fuse the *big switch* for channel routing and over-the-cells.
Create a new method "_do_globalSegment()" to delagate the
drawing of global segments between two GCell to the derived classes.
* New: In Anabatic, rename GCellTopology to NetBuilder, expose the class
(no longer in a local namespace).
NetBuilder become a base class performing the walkthrough the Net
tree. Derived class are tasked to build routing for specific gauge.
NetBuilderHV is created to manage all gauge with metal2 horizontal
and metal3 vertical.
In our terminolgy we consider that the first routing metal is
metal2. Metal1 is used inside the standard cells.
Jean-Paul Chaput