* Bug: In Hurricane, in HApplication, ExceptionWidget ans PyHurricane.h,
forgot to catch the Hurricane::Bug exception which was leading to
terminate() without explanations.
* Change: In Katabatic, In GCellTopology, now support one GCell with
five metal1 terminal of the same net. This unlikely configuration
did appear in the SNX for the first time...
* In Katabatic, in AutoSegment::canMoveUp(), adds the ability to reject
the move up if the density of the depth we comes from is below 0.6
in all the GCells, activated with the KbChecklowDensity flag.
* In Katabatic, In LayerAssign, new method moveUpNetTrunk2() which,
unlike the previous one, move up only the part of the Net trunk
which is connex to the seed segment. Use the canMoveUp with
low density checking to avoid unbalancing higher metal layers.
* In Kite, in SegmentFsm, use the canMoveUp() with low density checking.
* New: in Katabatic, in AutoSegment, recognize segments that are U-turn.
That is, based on two turn Contacts and going both top or bottom.
* New: In Kite, manage one pitch U-turn by making them diseapear from
the tracks. And make them same-metal when saving. Add a pack stage
to try to compact U-turn.
* Change: In Katabatic, in GCellTopology::doRp_AccessPad(), if the supporting
RoutingPad is big (more than two pitch), do not put the access
contact in the center but on the edge. This is to avoid cut violations
between the VIAs and the matrix of VIAs that may be generated under the
RoutingPad itself.
* Change: In Kite, in TrackSegment destructor, if the legnth of the wire,
without extensions is less than one picth, enlarge it so it encompass
it's source & target VIAs (to avoid notches).
* Bug: In Kite, in Track destructor, the TrackElements where detacheds,
but not deleted, causing a memory link.
* Change: In vlsispad, in Dots, add an enable/disable flag because when printing
into a cmess, it is only the base class ostream which is took into account
as none of it's methods are virtuals (silly me).
* Bug: In Etesian, print into cmess instead of cout and make use of the Dots
enabling feature.
* New: In Katabatic, added AutoContact::migrateConstraintBox() to transfert
constraint from one contact to another.
New flag for AutoContact, CntWeakTerminal for AutoContact which are at
the other of a segment directly connected to a terminal. They may hold
special constraints in case of caged terminals (computed in Kite).
In AutoHorizontal & AutoVertical, in ::_makeDogleg(), transfert flags
and constraints when breaking a segment directly connected to a terminal.
* New: In Kite, in protectCagedTerminals(), uses cross constraint on the
AutoContact opposite to the ContactTerminal (CntWeakTerminal) instead
of moving up one terminal over two consecutives. This is simpler without
degrading the routing quality.
* Change: In Knik, in Vertex, add a "blocked" flag to signal disabled
vertexes in the grid (must not be used by the global router).
Modificate the Graph::getVertex() method so that when a vertex
is geometrically queried, if is a blocked one, return a non-blocked
neighbor. This mechanism is introduced to, at last, prevent the
global router to go *under* the pad in case of a commplete chip.
* New: In Katabatic, in AutoSegment, a new state has been added: "reduced".
A reduced segment is in the same layer as it's perpandiculars.
To be reduced, a segments has to be connected on source & target to
AutoContactTurn, both of the perpandiculars must be of the same layer
(below or above) and it's length must not exceed one pitch in the
perpandicular direction.
To reduce an AutoSegment, call ::reduce() and to revert the state,
call ::raise(). Two associated predicates are associated:
::canReduce() and ::mustRaise().
Note: No two adjacent segments can be reduced at the same time.
* Bug: In Katabatic, in GCellTopology, add a new method ::doRp_AccessPad()
to connect to the pads. Create wiring, fixed and non managed by
Katabatic, to connect the pad connector layer to the lowest routing
layers (depth 1 & 2). The former implementation was sometimes leading
to gaps (sheared contact) that *must not* occurs during the building
stage.
Remark: This bug did put under the light the fact that the initial
wiring must be created without gaps. Gaps are closed by making doglegs
on contacts. But this mechanism could only work when the database if
fully initialised (the cache is up to date). Otherwise various problems
arise, in the canonization process for example.
* New: In Katabatic, in AutoContactTerminal::getNativeConstraintBox(),
when anchored on a RoutingPad, now take account the potential rotation
of the Path's transformation. Here again, for the chip's pads.
* New: In Kite, support for reduced AutoSegment. TrackSegment associateds
to reduced AutoSegment are *not* inserted into track to become
effectively invisibles. When a segment becomes reduced, a TrackEvent
is generated to remove it. Conversely when it is raised a RoutingEvent
is created/rescheduled to insert it. All this is mostly managed inside
the Session::revalidate() method.
* New: In Kite, in KiteEngine::createGlobalGraph(), in case of a chip,
mark all global routing vertexes (Knik) that are under a pad, as blockeds.
* Bug: In Cumulus, in PadsCorona.Side.getAxis(), inversion between X and
Y coordinate of the chip size. Did not show until a non-square chip
was routed (i.e. our MIPS R3000).
* Change: In Stratus1, in st_placement.py add the ClockBuffer class for
backward compatibility with the MIPS32 bench. Have to review this
functionnality coming from the deprecated placeAndroute.py.
In st_instance.py, no longer creates the Plug ring of a Net.
In my opinion it just clutter the display until the P&R is called.
Can re-enable later as an option (in Unicorn).
* Change: In Unicorn, in cgt.py, more reliable way of loading then running
user supplied scripts. Borrowed from alliance-checker-toolkit doChip.py .
* New: In Kite, in BuildPowerRails more accurate GCell density computation
under the pad area, to limit the overloaded messages.
* New: In Cumulus, In BlockCorona, remove the vertical METAL3 blockages
and replace them by horizontal blockages completly enclosing the
corona big vias in all layers. This way the I/O wires that goes
through the corona are guided to be straight and do not creates
unsolvable doglegs due to the presence of big vias.
* Change: In Kite & Etesian, small typo: refactor the method
"::wipeOutRouting()" into "::wipeoutRouting()" (indulge me, I'm a
code maniac).
* New: In Hurricane, In NetAlias & Net, add an AliasList collection to
iterate over all the aliases names (this *not* include the main
net name).
* New: In Hurricane, In Cell, Instance & Net add support for cloning and
uniquification (update documentation).
All Cells that are uniquified from a given model are kept in an
Uniquify relation. This relation allows to get all the clones and
generate unique clone names by adding a "_uXX" suffix.
* Bug: In Hurricane, the Cell::_isFlattenLeaf attribute was not initialized
in the constructor.
* Change: In CRL Core, in AllianceFramework::getCell(), no longer destroy
a partially loaded Cell in case of parser failure, let the incomplete
Cell be.
* New: In CRL Core, in ApParser, if all the instances are placed, sets the
Cell::Placed flag.
* Change: In CRL Core, in BlifParser, complete rewrite of the parser.
Not so good an idea afterwards...
* New: In Etesian, uniquify the design before placing.
* Change: In Kite, display the list of unrouted wired after all other
statistics.
* Change: In CRL Core, simplify the loading sequence. The technology,
both symbolic and real is now loaded directly from coriolisInit.py
and not through the Alliance loader. This was a leftover from the
time configuration was in XML. Remove others traces of XML loading.
Remove SYMB_TECHNO_NAME, REAL_TECHNO_NAME & DISPLAY from the Alliance
environement, as they was no longer used.
Note that technology *still* need to be loader *after* Alliance
framework has been initialized.
Gauge information is moved from <alliance.conf> to <kite.conf>.
* Bug: In Coloquinte, in optimization_subproblems.cxx static variables
must not be inlined. Generate a problem when linking in debug mode
(seems the symbol gets optimised out).
* Bug: In Katabatic, in Grid::getGCell(), when the coordinate is *outside*
the area, do not try to find a GCell, directly return NULL.
* New: In Unicorn, create a generic command launcher named "coriolis" which
automatically take cares of all environement setup, then run a command
by default, it's <cgt>, but it can be anything. For example: <zsh>.
* Bug: In Bootstrap, in coriolisEnv.py, check if devtoolset-2 is already
active before launching it as a sub-shell.
* Bug: In Isobar, In PyHurricane.h, DBoDestroyAttribute() set the proxy
pointer toward the C++ object to NULL. So when the Python object is
deleted no double-deletion occurs on the C++ object.
Add some more trace information in Python link/dealloc.
* Change: In CRL Core, in cyclop, make CMakeLists.txt automatically
choose the right rule for linking the binary wether we use Qt 4 or
Qt 5. Very irksome problem.
* New: In EtesianEngine::addFeed(), do not take into account instances
that are not placed entirely inside the top cell abutment box (was
causing a core dump).
* Bug: In Katabatic, in GCellQueue, correct a mismatch between a GCell
set and the iterators used upon it.
* Bug: In Mauka, in Row & Surface correct a mismatch between a container
and it's iterator.
* New: In Etesian, updated to work with the latest Coloquinte, patch
contributed by G. Gouvine.
Added EtesianEngine::setDefaultAb() to compute an abutment box if
the Cell is completly unplaced.
* New: In cumulus, in ClockTree, now the placer can be configured to be
either Mauka (slow simulated annealing) or Etesian (fast analytic).
New setting 'clockTree.placerEngine' in plugin settings.
* New: In Bootstrap, added support for RHEL7 in ccb.py & coriolisEnv.py.
In coriolisEnv.py, under RHEL6, directly launch a shell under
devtoolset-2 (do not put it in .bashrc).
* Change: All tools, compliance with Clang 3.2.
- Call using namespace std *after* at least one include of std has
been used.
- In Utilities.h define both const and non-cont overload for operator<<
of mstream (this was the true cause of the Banner display problem).
- No longer use defaults arguments in templates, instead create two
separated overloads.
- Put template static attributes allocation outside of namespaces
(this one I'm not sure how to justify).
- Protect by NDEBUG variables that are only needed in assert().
- In PyInterval getUnion() & getIntersection() we where silently
overwriting the "self" object (interval).
- In Mauka, *do no* overload _postCreate() and add an argument, breaks
the virtual function mechanism. Rename it into _maukaPostCreate().
Idem for SubRow().
- In Katabatic::GCell(), invalidate() overload a Go funtion but is
used for different purpose at this level. Rename it invalidateCt()
(invalidate *ConTents*).
- Miscellaneous small cleanup.
* Change: In Katabatic, in AutoSegment::canonize() and
Session::_canonize() no longer tag Global as WeakGlobal also.
This avoid to try to make dogleg on them when we shouldn't.
They where staying WeakGlobal even when there were no longer
connected to a global.
* Change: In Katabatic, in AutoSegment::makeDogleg(), suppress the
bug for pad message when we are in the global routing stage.
At that point it is allowed to make doglegs under the pads are
they are "layer change" ones.
* Change: In Hurricane, the NetRoutingProperty is moved into Hurricane
from Katabatic. Needed for Knik to be able to access thoses
informations.
* Change: In Hurricane, in RoutingPad::setOnBestComponent(), now in
case of identical area, select the component of lowest id.
This should not be needed if the component ordering was fully
deterministic as it should be (will investigate later).
This is to ensure that the choosen component is always the
same, especially between save/load of a global routing.
* Bug: In Katabatic, in AutoContactHTee::updateTopology(), invalidate
the segments only if the topology is valid (no NULL in the
cached segments).
* Bug: In Katabatic, in GCellTopology::construct(), throw an error
if the topology is bad instead of trying to continue (and core
dump later... ).
* Bug: In Kite, in BuildPowerRails, distinguish the name of the master
net in the pad (for vddi, vssi, vdde, vsse, ck, cki & cko) and the
name of the net in the *chip* netlist. Must use the later to make
comparison as they may differs.
* Change: In Knik, in save/load solution, exclude nets that are not
globally routed by Knik. That is which NetRoutingProperty is not
*Automatic*.
* Bug: In Cumulus, in chip.BlockPower take account of the layer
width extention to sligthy shrink the connector thus avoiding a
notch with standart cell in some cases.
* Change: In Cumulus, in chip.ClockTree disable the use of fixed Steiner
trees for the leaf clocks, as it seems overconstrained for the
router. First move was to lower them in M2/M3 (instead of M3/M4)
but that was not sufficent.
* New: In Cumulus, RSavePlugin for recursively saving a physical
hierarchy.
* New: In documentation, first embryo for RDS file. Should have been
in Alliance git, but I prefer to keep newest doc in Coriolis.
* Bug: In Katabatic, in AutoContactTurn::cacheAttach() unset the
"cache invalidated" flag *only* if the h1 & v1 component are
sets. This is needed because we can attach *before* the first
cache revalidation (in the initial building stage).
* Bug: In Katabatic, in AutoSegment::getPPitch() out of bound access
of the top of the RoutingGauge, in case of a top layer segment
with a spin top flag (maybe this shouldn't happen?).
* Change: In Kite, in SegmentFsm::conflictSolveByPlaceds() take
account as conflicting other global, global, blockage *and*
now fixeds.
* Change: In Cumulus, in px2mpx.py more accurate way of transforming
the pad blockages.
* New: In CRL Core, in helpers & alliance.conf, set and read a "PAD"
variable to define the pad model name extension ("px" for "sxlib
and "pxr" for vsxlib, this is provisional).
* New: In CRL Core, in plugin.conf, add parameters to define the name
of used for power & clock supply. We may remove the extention in
the future (to be more coherent with the previous modification).
* New: In Cumulus, in chip.Configuration.GaugeConf._rpAccess(), no
longer place the accessing contact *at the center* of the
RoutingPad. It works under sxlib because buffers & registers all
have same size terminals. But this is not true under vsxlib,
leading to misaligned contacts & wires. Now systematically place
on the slice midlle track (maybe with one pitch above or below).
This is still very weak as we do not check if the terminal
reach were the contact is being put. Has to be strenthened in
the future.
* New: In Cumulus, in chip.Configuration.ChipConf, read the new
clock & power pad parameters.
* Change: In Isobar (and all other Python wrappers), uses PyLong instead
of PyInt for DbU conversions. In PyHurricane argument converter,
automatically check for both PyLong and then PyInt.
* Change: In Cumulus, in chip.PadsCorona, more accurate error message
in case of discrepency in global net connections (i.e. no net
of the same name in instance model and instance model owner.
* Change: In Kite, in BuildPowerRails, when looking up at the pads
model name to find "pck_" or "pvddeck_", do not compare the
extension part. But we still use hard-coded stem pad names,
maybe we shouldn't.
* Bug: In Katabatic, in GCellConfiguration::_do_xG_xM1_xM3(), there
was a loop in the search of the best N/E initial RoutingPad.
* Bug: In Kite, in KiteEngine::protectRoutingPads(), *do not* protect
RoutingPads of fixed nets, they are already through the
BuildPowerRails stage (and it's causing scary overlap warning
messages).
* Bug: In Cumulus, in ClockTree.HTreeNode.addLeaf(), do not create
deep-plug when the core is flat (not sub-modules). All the new
nets are at core level.
* Bug: In Cumulus, in ChipPlugin.PlaceCore.doFloorplan(), ensure
that the core is aligned on the GCell grid (i.e. the slice
grid of the overall chip).
* Bug: In Kite, in GCellTopology::_do_xG_xM1_xM3(), infinite loop
while looking for the bigger N-E RoutingPad. Forgot to decrement
the index...
* Change: In Hurricane, in Plug::setNet(), more informative error messages.
* Change: In Hurricane, In Segment, more informative error messages.
* Change: In Hurricane, In DeepNet, accessor for the Net occurrence.
* Bug: In Katabatic, in AutoSegment::create(), error message uses correct
variables (vertical was using horizontal)...
* Change: In Kite, in BuildPowerRails, already existing wiring in instances
is copied up as blockage. Uses blockage layer instead of true layer
(it was a bug).
* Change: In Kite, in BuildPreRouted, consider as manual global routing
nets with only default wiring (default size wire & contacts).
Non-default routing is flagged as fixed (with the NetRoutingState
property).
* Change: In bootstrap, in ccb & builder, build by default with Qt4 and
provide a --qt5 command line switch to enable Qt5.
FindBootstrap.cmake now provides a qtX_wrap_cpp() macros to be
independant of the version of Qt being used.
Add all thoses options to the graphical interface to the builder.
* Change: In all the tools using Qt, switch to the qtX_*() macros from
FindBootstrap.cmake.
* Change: In Hurricane, in CellViewer, revert to the Qt4 way of connecting
signal/slots for backward compatibility.
* Bug: In Kite, in TrackCost, the boolean attribute "_forGlobal" was not
initialized in the constructor causing the non-deterministic behavior.
Arrrrgggghhhhhh.
* Bug: In Kite, in PyKiteEngine, forgot to perform the
"balanceGlobalDensity()" in the layer assign Python wrapper, another
cause for non-determinism.
* Change: In Kite, In KiteEngine, print the configuration at the same
point as in the python script (to get identical output).
* New: In Katabatic, add the ability to decorate some (i.e. few) nets
with a state that indicate to Katabatic & Kite what to do with it.
The possible states are:
1. Fixed : all the wire are in fixed positions. The router cannot
move them and account them as obstacles.
2. ManualGlobalRoute : a user-defined topology is supplied. The
wires still have to be detailed route in "Detailed Pre-Route"
but will be skipped for the global routing and fixed for the
general Detailed route.
3. AutomaticGlobalRoute : ordinary nets, to be global routed then
detail routed.
4. Excluded : do not try to global or detail route thoses nets.
5. MixedPreRoute : mask combining Fixed and ManualGlobalRoute.
Not all nets have this property, only those that needs a special
processing.
To ease the access to the state, it is nested inside a
PrivateProperty in the net (NetRoutingProperty), with an extension
access class (NetRoutingExtension).
* New: In Kite, take account of NetRoutingState. Pointers to the
net's states are strored inside an internal map for faster access.
The property is *not* deleted when Kite is destroyed. The property
will remains until the Net itself is destroyed.
As a consequence, the lists that where passed to high level
function are removed as the information can now be accessed directly
through the net NetRoutingProperty.
* New: In Unicorn, in CgtMain, comply with the update interface.
* New: In documentation, update the User's Guide to explain the Pre-routed
step of Kite.
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
* Change: In Kite, Katabatic & Knik, express the number of tracks truly
available to the global router by the number of tracks reserved to
the local routage inside a GCell. Replace the ratio parameter
"hEdgeCapacity" by an integer parameter "hTracksReservedLocal"
(duplicate for verticals).
It is more explicit to give directly the number of tracks that
are to be used locally, and potentially saves us from rouding
problems when calculating the number of availables tracks.
Note: we cannot do that for the layer saturateRatio as it
uses the density ratio that take account local wires, leading
to fractional results.
* Change: In Katabatic, in <GCellGrid>, rename checkEdgeSaturation()
into checkEdgeOverflow(), more explicit.
* Change: In Knik, in <Graph>, display the computed capacities of the
lower left node edges (should be the same througout all the grid).
* Change: In Unicorn, in <cgt.py>, uses the new parameters names for
edge density.
Placement management:
* Change: In <metis>, always disable the hMetis support regardless of
it being detected or not as the placer is still unable manage the
final bin contents.
Routing gauge management:
* Bug: In CRL Core, <vsclib/alliance.conf>, set the correct pitches and
size for the routing layers and the cell gauge.
* Change: In Katabatic & Kite, extract the correct extension cap for each
routing layer from the layers characteristics (cache then in
Katabatic::Configuration).
* Change: In Katabatic, <AutoSegment>, create segment with the wire width
defined in the gauge. For AutoSegment created on already existing
Segment from the global routing, adjust the width.
* Change: In Katabatic, <AutoSegment>, more accurate information about how
a segment is connected to terminal via source and/or target.
The flag SegStrongTerminal is splitted into SegSourceTerminal and
SegSourceTarget (but still used as a mask). So now we can know by
which end an AutoSegment is connected to a terminal.
* Change: In Katabatic, ::doRp_Access(), create constraint freeing segments
not only when HSmall but also when VSmall (more critical for <vsclib>).
Otherwise we may see AutoSegments with incompatible source/target
constraints.
* Change: In Kite, BuildPowerRails, do not create blockage on PinOnly
layers *but* still create power rails planes. This is a temporary
workaround for <vsclib> where the METAL1 blockages overlaps the
terminals (it was fine for Nero, but they shouldn't for Kite).
* Change: In Kite, <RoutingEvent>, if a TrackSegment is overconstrained,
directly bybass it's slackening state to DataNegociate::Slacken.
Also rename the flag "_canHandleConstraints" to "_overConstrained",
seems clearer to me.
Miscellaneous:
* Change: In CRL Core, <Utilities>, add a "pass-though" capability on the
mstream to temporarily make them print everything.
In Katabatic & Kite, remove all hard-coded values related to track pitches.
* New: In <Session>, add more convenience function to access RoutingGauge
characteristics.
* New: In <AutoSegment>, <AutoContact>, add support for the "depth spin",
that is, if the source/target contacts are going "top" or "down".
Used to compute the perpandicular pitch. Need a small modification
of the revalidation mechanism. The observers of <AutoSegment> are
notified when the spin changes.
* New: In <AutoSegment>, the getPPitch() method allow to compute the
"perpandicular pitch". For now it is simply the greatest from the
source perpandicular pitch and the target perpandicular pitch.
Make uses of the "depth spin".
* New: In <TrackElement>, <TrackSegment>, cache the perpandicular pitch.
Updated through the notification from the observable.
When upgrading from doxygen 1.5.x to 1.8.5 the way the documentation
is generated has underwent many changes, particularly in the headers.
* Change: In <header.html>, must include the javascripts <jquery.js>
and <dynsections.js>.
* In <CMakeLists.txt>, as the header is customized, doxygen seems not
copy some files like the javascripts and some images (open.png,
closed.png). So we copy them from doxygen installation and make
the CMakeLists.txt install them. I hope they will not change too
much in the future.
* In <doxyfile>, disable markdown support as it do not interpret
correctly the formating we already adopted (with a left margin
to put command into). Use HTML_EXTRA_STYLESHEET instead of
HTML_STYLESHEET. Enable the index (DISABLE_INDEX=NO), for the
top header. Enable dot for inheritance diagram. Set the
EXAMPLE_PATH=. to include the synthetic hierarchy.
Correct the tag inclusion (faulty path in some places).
* In <SoC.css>, create style for the new header generated by doxygen.
* In the documentation, move the synthetic hierarchy into a module.
Miscellaneous:
* Change: In <crlcore>, in display.conf use the same display threshold
for both METAL2 & METAL3.
In alliance.conf, the side of VIAs in the gauge is 2l (not 3l).
In kite.conf, separate edge densities for H/V.
* Change: In <Cell>, in flattenNets() use flag as argument, not a
boolean. Do not create rings for clock or supply nets.
* Change: In <DeepNet>, in _createRoutingPads() do not create rings
for clock or supply net (duplicated policy as in Cell::flattenNets()).
* Bug: In <ControllerWidget>, at last find the bad signal disconnect
that was causing ungraceful messages.
* Change: In <knik>, in Edge display occupancy/capacity in the string
name. Improved display progress and debugging capabilities.
Improved exception catch & breakpoint managment:
* Bug: In <PaletteWidget>, in updateExtensions() replace the calls to
deleteLayer() by delete. This cause the widget to be immediatly
erased instead of waiting for the event queue to be completly
processed. This was causing the widget to be left in a incoherent
state when stoping at a breakpoint.
* Bug: In <BreakpointWidget>, in execNoModal(), flush the main event
loop (QApplication::flush()) *before* lauching the *local* event
loop. This is to ensure all widgets are in their final state when
waiting (especially <PaletteWidget>).
* Change: In <ExceptionWidget>, new method catchAllWrapper() to
execute any std::function< void() > function/method with a "try"/
"catch" wraparound and lauch the widget in case something is catch.
* New: In <hurricane>, support for a oberver pattern, backported from
<katabatic> with an Obervable capable of being linked to any
number of Obervers.
* New: In <Cell>, made it observable to detect Cell change, currently
emit two kind of signals:
- Cell::CellAboutToChange : *before* any change.
- Cell::CellChanged : *after* the change has been completed.
* New: In <UpdateSession>, in Go::invalidate() add the Cell owning the
Go to the UPDATOR_STACK (of course the cell is added only once).
In addition, when the Cell is added, send a notification of
Cell::CellAboutToChange to all it's observers. The slave instances
are also invalidated.
Conversely in UpdateSession::_preDestroy() for each invalidated
Cell send a Cell::CellChanged notification to all observer.
The UPDATOR_STACK has been slightly amended to accept Cell which
are not Gos. Prior to this, the Cell where completly excluded from
the UpdateSession mechanism, so it's instances where never actualised
of anything referring to the Cell for that matter.
Note: we use two different mechanisms to transmit a Cell change,
observers and the slave instance map. I think at some point it
should be unificated.
* Change: In <CellViewer>, make it a Cell observer to redraw when the
cell is modificated (also update the palette).
Uses the catchAllWrapper() to protect all critical actions.
* Change: In <GraphicTool>, no longer need of cellPreModificated and
cellPostModificated signals. Now done through the Cell obersvers.
* Change: In <mauka>, <etesian> & <kite> now uses the catchAllWrapper
method for protection (need to split methods in two, to be able
to pass it as argument). No longer emit cellPreModificated and
cellPostModificated.
Support for RoutingGauge in P&R:
* Bug: In <placeandroute.py>, the connection from the internal power
ring to the connectors was not done correctly. Wrong contact layers
leading to a gap.
* Change: In <BuildPowerRails>, detection of the corona signals based
on how the "pck_px" pad is connected. No longer based on name
matching.
* Change: In <placeandroute.py>, support for 2 routing metal only
(3 metal in the technology).
* Change: In <katabatic> & <kite> support for a "top layer" limitation
on the routing gauge, this allows to use only two routing metals
(METAL2 & METAL3). Work in progress.
Update to Qt 5:
* Change: Now requires at least cmake 2.8.9.
* Change: CMakeLists.txt needs small changes. Qt modules must be found
one by one (Core, Gui, Widgets). Must add "set(CMAKE_AUTOMOC ON)"
in the top file and replace "qt4" prefix in macros by "qt5".
Added simpler macro "setup_qt()" in FindBootstrap.cmake.
* Change: No longer need to include <QGtkStyle> is is choosen by default
according to the current desktop environment.
* Change: In <hurricane>, In HApplication, launch ExceptionWidget when
a std::exception is catched instead of silently discarting it.
New placer Tool: Etesian
* New: <etesian> analytical placer. Encapsulate Coloquinte from
Gabriel Gouvine.
* New: in <documentation>, add stub demonstration ToolEngine <smurf>.
Needs to be commented.
Miscellaneous:
* New: in <boostrap> and <unicorn>, added support for Etesian, the new
analytic placer. The tool itself will be added in the next commit.
* Bug: in <CellWidget>, when shifting the display buffer, we no longer
can copy the buffer on itself (we should never have). Now go through
a temporary one (PlaneId::AutoCopy) which is added to the
DrawingPlanes. Affect "goLeft()" and "goUp()".
* Bug: In <CellWidget>, remove the WA_PaintOnScreen flag/attribute.
When it's on, no PaintEvent is transmitted to the CellWidget
when it's the central widget of the <CellViewer> (QMainWindow).
It's something I still don't understand from the doc of Qt.
* Change: In <AreaCommand>, use the PlaneId enumeration instead of a
anonymous numerical index.
* Change: In <HApplication>, no longer catch and silently discard
standartd exceptions but launch the ExceptionWidget...
Suppress the now deprecated constructor with "Type" argument.
* Change: In <SelectionModel>, the "reset()" method is deprecated in
Qt5, instead enclose the "clear()" by a "beginResetModel()" and
"endResetModel()" pair.
* New: In <crlcore>, add support for ISPD05 benchmarks (in Bookshelf
format). Forked from ISPD04 and not finished yet.
* Change: In <Mauka>, distinguish the Action string identifier from
<Etesian>
* New: In <unicorn>, add entry for ISPD05 loader. Add entry for
<Etesian> analytic placer.
Details:
* New: in <bootstrap>: add support for devtoolset-2 in ccb. Run the
cmake commands through 'scl', set shell environment variables
BOOST_INCLUDEDIR & BOOST_LIBRARYDIR and disable the default
system path search.
* Change: In various flex scanners add the %nounput to suppress
compiler warnings.
* Change: Little cleanup for g++ 4.8.1 as it's more strict.
* Change: In various top CMakeLists.txt, suppress extraneous '/'
after DESTDIR.
Documentation restructuration:
* Bug: in <hurricane>: bad figure for transf-R1.
* Change, in <kite>: Remove deprecated configuration variables.
* New: documentation <tool> to regroup all documentation not directly
related to one tool.
* Change, in <crlcore>, move the user's guide and the top doc index
into <documentation>.
* New, in <documenation>: added Python script demo based on AM2901.
- In Session::_canonize(): if the canonical segment has never had it's axis
sets, put it into *optimal* position instead of simply constraint
compliant. Force realignment of the segment sets as rounding errors
may introduce slight misalignment on the axis (causing error laters
in the various contact topological updates).
This also seems to solve the ludicrous problem of negative ratio of
expansion wires... (segments *not* at their optimal position at the
start).
- In LayerAssign, KatabaticEngine::layerAssign(), suppress the triple loop
enclosign the desaturation. Now desaturate each layer exactly once and
from bottom to top.
- New: Added FreeBSD/Ubuntu patches from Otacilio De Araujo
(<otaciliodearaujo@gmail.com>).
* ./katabatic:
- New: Makes use of cbug to display the (scary) debug messages.
- New: In LayerAssignement & GCell, perform layer assignment on whole net
trunk, instead on a segment by segment basis.
- New: In GCell, fragmentation analysis. When a layer change is requested,
it allows to check if the additionnal perpandiculars created to
maintain connexity will not over fragment the layer. This is particu-
larly critical for M3->M5 which create M4 in perpandiculars, and M4
may be subject to very dense configuration.
- New: In AutoSegment & LoadGrByNet, adds a flags telling if the net's
degree equal 2. Has not proven to be useful yet.
- New: In AutoSegment, adds a flag telling if the segment is the perpan-
dicular part of a dogleg. Has not proven useful yet.
- New: In GCell, compute a "fragmentation" indice, the average free track
length, the more fragmented, the smaller the indice.
- New: In AutoSegment::canMoveUp(), when requested, not only check for free
(parallel) track in the up layer but also check that the begin/end
local segments created to maintain layer connexity do not creates too
much fragmentation. This fragment could prove critical in higly dense
GCells.
- Change: In LayerAssign, disable the ::rpDesaturate() steps, after optimization
the router can handle 10 terminals per GCells in M2 without problem.
And ::rpDesaturate() must uses GCell::stepNetDesaturate() and *not*
directly ::stepDesaturate().
- New: In AutoSegment, adds a "_parent" attribute to keep track of the fragmentation
processus. Currently used only for strap segments, points to the original
segment in the appropriate direction (before the split).
- New: In GCell & LayerAssign, new method of layer assignment. Move up
the whole net trunk if only one of it's segment is inside an over-saturated
GCell. AutoSegment are moved up only if there is at least 2 free tracks
remaining on the upper level.
- Change: In Session::_canonize(), uses the lowest segment Id as canonical.
More reliable than geometricals criterions in the end. Assuming that the
segments are being created in deterministic order, which *should* be the
case consediring the way we are walking through the global routing.
- Change: In AutoSegment, completly suppress the CompareCanonical(), replace
it by the much simpler CompareId().
- Change: In GCell::rpDesaturate(), stops desaturation when bottom density
is under 0.5, otherwise we are causing a severe imbalance in M2/M4
densities. All wires pushed up to M4...
- Change: In ChipTools, for the Pad's RoutingPad, reslect the best component
using the one in the lowest layer. To avoid problem when splitting
AutoContact as we expect the base Contact to be on the lower layer.
- Bug: In GCellConfiguration::_GCell_xG_xL1_xL3(), add H/V alignement constraints
in fork case. This allow NE/SW contact to be splitted correctly later.
- Bug: In AutoContact::split(), the connexity on the splitted contacts was
not correctly restored, leading to canonization and parentage looping
errors. This was concealed by the Kite Track::_check() bug (incomplete
individual TrackSegment checking).
- Change: In GCell & GCellGrid, unificated way of computing all the GCell's
densities.
- Change: In GCell::stepDesaturate(), uses shearUp() instead of moveUp().
- Change: In AutoSegment, new method ::shearUp() to avoid moveUp() saturating
GCells as side-effect.
- New: ChipTools, regroup all datas and utilities to manage a full-chip
design.
- Change: In LoadGrByNet/GCellConfiguration::_GCell_xG_1Pad(), uses straight
perpandicular wires on top & right pads. The GCells under those connectors
are fully saturated, wires must go out as straight as possible.
- Change: In AutoHorizontal/AutoVertical, update the "terminal" flag after
slackening. This is to avoid global that are no longer connected to
terminals behave as such.
- Change: In AutoSegment::canMoveUp() & canPivotUp(), prevent all local segments
to go up. This is to avoid cluttering upper levels with small segments.
- Change: In GCellConfiguration, for xG_xL3, detect straight vertical topologies
and for them to be fixed (new flag FIXED_GLOBAL set by the topological
builder instead of the constructor). This prevent the router to do
stupid things...
To sets the "Fixed" flag *after* the axis of global segments have been
positionned correctly adds a "_toFixGlobals" static table lookup.
- Change: In GCell::stepDesaturate(), if less than one free track remains in
the upper layer, do not move up the segment. This allows from a minimum
free room for expansion.
- Change: In GCell::_getString(), display indexes and layer names in various
saturation tables.
- Change: In AutoSegment, allow move up of local Segment. ::moveUp() and
::canMoveUp() arguments go from booleans to flags, which are more
explicits.
- Change: In loadGlobalRouting(), more exlicit message as to why a net is
filtered out the routing set (POWER, GROUND, CLOCK or BLOCKAGE).
- New: ChipTool, module with utilities specific to chip routing. Containing
a function to pre-break wires around a block.
- New: In loadGlobalRouting/GCellConfiguration, adds supports for RoutingPad
connected on chip's pad.
- New: In GCellGrid/GCell, can compute the density in three modes: average,
max of H/V and max of layer. Currently implemented in getMaxHVDensity(),
should be unificated with getDensity(). Used for display purposes.
- Bug: In AutoContact, when splitting a contact, add a specific check for
"one layer span".
- Bug: In AutoSegment::canMoveUp(), do not move up fixed segments.
- Change: In LayerAssign, desaturate until the last two top layers are reacheds
instead of only METAL2 & METAL3.
- Change: In Configuration/GCellGrid/GCell, correct computation of the edges
capacity (based on the numbers of avalaibles layers and not hard-wired to
4).
- New: To pass the ibmXX, new parameter "katabatic.saturateRp" which allows
to sets the threshold above which a GCell has too much RoutingPads in
it and must be further desaturated. Must be 8 for FPGA, and 10 for ibm.
- Bug: In LoadGrByNet(), when looking for the starting GCell, the computation
of unconnecteds RoutingPads was incorrect, too great and letting the
router believe that the routage was incomplete.
Jean-Paul Chaput
Gabriel Gouvine
The Coriolis Project