Previously, the relevant NetBuilder and routing strategies where
directly guessed from the RoutingGauge traits. This is no longer
doable as the combinations increases. Now to configure both the
global and detailed router we need three "parameters" :
1. The routing gauge itself (tells which layers are in which
directions) and how to make the VIAs.
2. The NetBuilder to use, they are identified by strings.
Currently we support:
* "HV,3RL+", for all SxLib derived standard cells.
* "VH,2RL", for hybrid routing (over the cell, but terminals
are also in the first RL).
* "2RL-", for strict channel routing.
* "VH,3RL+", an attempt for FreePDK 45, not optimized enough
to be considered as usable.
3. The routing style, mostly affect the way the GCell grid will be
built.
* VH : first RL is V.
* HV : first RL is H.
* OTH : Run in full over-the-cell mode (needs at least 3RL).
* Channel : Run in *strict* channel routing mode (no routing over
the standard cells).
* Hybrid : Create channels, but can use H tracks over the
standard cells.
Thoses three parameters are partly overlapping and must be sets in
a consistent manner, otherwise strange results may occurs.
* New: CRL::RoutingGauge::getFirstRoutingGauge(), to get the lowest
layer available for routing (not a PinOnly, not a PowerSupply).
* Change: In CRL::RoutingGauge::isHV() and isVH(), were previously
always returning false when the gauge was 2RL only. Now, check
on the first usable RL.
* Bug: In cumulus/plugins.block.configuration._loadRoutingGauge(),
there was a bad computation of the deep RLs when the top layer
was not defined. Occured for 2RL gauges only.
* Bug: In Anabatic::RpsInRow::slacken() (LayerAssign), forgotten curly braces
in the test to skip METAL2 terminals.
* Change: In Etestian::BloatChannel::getDx(), adjust the bloating
policy to converge on Arlet6502. Always ensure that there is
a 50% ratio between terminal used V-tracks and free ones.
If there is more than 80% of terminals, add one more track.
* Bug: In AnabaticEngine & KatanaEngine, KatanaEngine is a derived
class of AnabaticEngine. They uses Anabatic::Configuration
and Katana::Configuration that also derives from each other.
I though I had made one configuration attribute in the base
class that was using the right Configuration. But no. I did
have two configurations attributes, one in AnabaticEngine and
one in KatanaEngine, the later "shadowing" the former. As a
results, parameters modified in AnabaticEngine, *after* the
initial creation of the tool *where never seen* at Katana
level (due to it's own duplicate). What a mess.
Now there is only one attribute in the *base* class Anabatic,
which is created through a new virtual function _createConfiguration()
called in _postCreate() which allocate the right Configuration
according to the dynamic type of the tool (KatanaEngine).
In KatanaEngine, access the configuration through the
attribute (_configuration) and not the accessor (getConfiguration()).
* Bug: In KatanaEngine, no longer directly use the _configuration attribute
(which is not accessible anyway) but the getConfiguration() accessor.
The accessor perform a static_cast from the Super::getConfiguration()
into Katana::Configuration.
Complete cleanup of the various configuration accessors.
* New: AnabaticEngine::setupNetBuilder(), perform an early check
of the requested NetBuilderStyle. The NetBuilderStyle is just a
string that will be matched against the (hard-coded) supported
NetBuilders. Then check the topological characteristics against
the capabilities of the gauge (HV, VH and so on).
Still a bit too hard-coded for now.
This function has been split from AnabaticEngine::_loadGrByNet().
* Change: AnabaticEngine::isChannelStyle() renamed from isChannelMode().
* New: In Anabatic::Configuration, two new attributes to select the
topology and routing style:
- _netBuilderStyle to explicitely select the NetBuilder to use.
It's a string, which is provided by each NetBuilder.
- _routingStyle to define how the overall routing will work.
It's a set of flags (StyleFlags):
* VH : first RL is V.
* HV : first RL is H.
* OTH : Run in full over-the-cell mode (needs at least 3RL).
* Channel : Run in *strict* channel routing mode (no routing over
the standard cells).
* Hybrid : Create channels, but can use H tracks over the
standard cells.
* New: In anabatic/Constants, add StyleFlags to define how the router
should operate (see above).
* Bug: In Anabatic::GCell, in CTOR, no reason to set up the HChannelGCell flag.
* Bug: In Anabatic::GCell::updateDensity(), when computing layers non contiguous
saturation, do not systematically skip RL 0, but only if it's PinOnly.
* Change: In Anabatic::NetBuilder, rename isTwoMetal by isStrictChannel.
* Change: In Anabatic::NetBuilderHV, rename doRp_AccessNorthPin() in
doRp_AccessNorthSouthPin(). More accurate.
* Bug: In NetBuilderHV::_do_1G_xM1_1PinM2(), the wires to connect the M1
terminals where created *twice*. Uterly stupid, there where placed in
overlap by the router!
* New: In AnabaticEngine, new accessors to the NetBuilderStyle and
RoutingStyle, proxies towards Configuration.
* Bug: In Manipulator::relax(), if there are two doglegs to be done, but
they are in the same GCell, only do one (the conflicting interval)
is short.
* Change: In Katana::Session, rename isChannelMode() into isChannelStyle().
* Change: In TrackSegment::isUnbreakable() and isStrap(), return false
when the base segment is a *weak global* (aligned with a global one).
* Change: In Katana::Row::createChannel(), correctly distinguish between
*strict channel* style and *hybrid* style. Tag the GCells as std cells
row or channels only in the former case.
* Update: In CRL/node600/phenitec/kite.py, update the routing gauge to
the new format. So now we can use again SxLib-2M (channel routing
SxLib for two metal technologies).
* Change: In CRL::BlifParser, if a master cell is not found in the
AllianceFramework, then try in the Blif supplied libraries.
This is used to load the zero, one and tie cells.
Add a Blif::getCell() static function to look into the Blif
supplied libraries.
* Change: In CRL::LefImport, sometimes there can be discrepencies between
the LEF ROUTING layers and the Coriolis routing gauge. Now ignore
routing layers that are *not* presents in the Coriolis gauge.
* Change: In AnabaticEngine, moved routingMode attribute from KatanaEngine,
as some setup operations needs it.
* Change: In AutoSegment::canReduce(), allow fixed segments to be reduced
if they are "jumpers" (turn+turn and top+top or bot+bot).
This case arise on the edge of routing channels for fixed wires
to connect terminals.
* Change: In AutoSegment::getTopologicalinfos(), compute differently the
(leftBound,rightBound) interval when in channel mode.
In over-the-cell mode, this interval is the one of the whole
GCells under the wire. In channel mode, for fixed wires (that is,
verticals connecteds to cells) this interval is reduced to half
the GCell height, on the connected side of said channel.
This allows Manipulator::_insertToTrack() to issue disantangling
requests (push left/push right) for fixed segments that are face
to face in the channel.
* Change: In Anabatic::Configuration CTOR, allow the cellGauge to have a
different name from the routingGauge. Now if the cell gauge that
should match the routing gauge is not found, fallback to the
name set in "anabatic.cellGauge" parameter.
Case occur when we try to match with CORE sites from LEF files.
* Change: In Etesian::Configuration CTOR, same change as in the
Anabatic configuration.
* Change: In Anabatic::GCell::updateDensity(), never set the GoStraight
flag in channel mode. This flag makes sense when there is at least
4 routing layers (so we have 2 contiguous free of blockages).
* Bug: In Anabatic::Session::_getNearestGridpoint(), sometimes the nearest on
grid point is outside the constraint box. Now force the point
to remains inside constraints even if offgrid.
* Change: In Katana::DataNegociate::update(), perpandiculars that are
either reduced or in non-preferred routing direction should not
trigger a bug message.
* Change: In KatanaEngine::_check(), do not check for fixed, horizontal
non-prefs AutoSegments in channel mode (avoid false bug display).
* Bug: In Manipulator::_forceToTrack(), slighty shrink (-1) the interval
to free. The intersection function of intervals returns true when
the two intervals *exactly* touches (1.vMax == 2.vMin). But in
this specific case, they are not *overlapping* and no action
should be taken...
* Bug: In Manipulator::_insertInTrack(), do not reject the track when
we are overlapping a fixed vertical segment in channel mode.
(Hmm, maybe already corrected by the previous one).
* Change: In Katana::NegociateOverlapCost(), in channel mode, do
not put two overlaping vertical fixed segments into infinite cost.
This happens when two cell connected verticals are face to face in
a channel. We want them negociated the track (by shrinking their
length) instead of excluding it right away.
* Change: In NegociateWindow::createTrackSegment(), in channel mode,
do not attempt to create a track segment over a fixed and reduced
AutoSegment.
Do not attempt to put a non-preferred AutoSegment on a Track
either.
* Bug: In RoutingEvent::revalidate(), the number of availables tracks
was badly computed when in the pure constraint case, when there
was only one it was reporting zero.
* Change: In TrackElements::TrackElements_Perpandicular::Locator,
do not issue a bug when an non-pref or reduced AutoSegment do not
have an associated TrackElement.
* Change: In TrackSegmentCost::update(), do not issue a bug when a
perpandicular is reduded or non-pref and do not have a TrackElement.
The decoupling of the cell gauge and the routing gauge implies that
the METAL2 & METAL3 terminals of macro blocks cannot be aligned on
the routing tracks anymore. That is, an horizontal METAL2 terminal
will not be on a track axis, but offgrid, so we no longer can use
a METAL2 horizontal segment to connect to it. Making an adjustement
between the offgrid terminal and the on-grid segment has proven
too complex and generating difficult configuration for the router.
Moreover, METLA2 terminal could be fully inside a METAL2 blockage.
So now, when the gauges are decoupled, we connect the METAL2 and
METAL3 the same way we do for METAL1: *from above* in the perpandicular
direction and using a *sliding* VIA. We assume that those kind of
terminals in upper metals are quite long.
* New: In Hurricane::Rectilinear, export the isNonRectangle() method
to the Python interface.
* New: In CRL::RoutingGauge, add function isSuperPitched() with the
associated boolean attribute. Set to true when each pitch of
each layer is independant (not low fractional multiples).
* New: In AnabaticEngine, add the ability to temporarily disable the
canonize() operation (mainly used in dogleg creation).
* New: In AutoSegment::canonize(), do nothing if the operation is
disabled by AnabaticEngine.
* Bug: In Session::_revalidateTopology(), disable the canonization
during the topology updating of a net. Too early canonization
was occuring in makeDogleg() leading to incoherencies when
performing the later canonization stage over the complete net.
Mostly occured in the initial build stage of the net.
* New: In GCell, add function postGlobalAnnotate(), if a layer
is fully blocked (above 0.9), typically, under a blockage,
add a further capacity decrease of 2 on the edges. So we may
handle a modicum of doglegs.
* Bug; In GCell::addBlockage(), removeContact(), removeHSegment()
and removeVSegment(), forgot to set the Invalidated flag.
This may have lead to innacurate densities.
* Change: In GCell::updateDensity(), more complex setting of the
GoStraight flag. This flag is now set if we don't have two
*contiguous* below 60% of density. We need free contiguous
layers to make doglegs.
* New: In NetBuilder, now manage a current state flag along
with the state flag of the *source* GCell. This flag is used
to tell if the GCell needs it's *global* routing to be done
using the upper layers (METAL4 & METAL5) instead of the
lower ones.
* New: In NetBuilder::setStartHook(), set the state flag of the
GCell to ToUpperRouting when processing a global routing
articulation and one of the base layer is obstructed
above 0.9.
In GCell with terminals, also set ToUpperRouting when there
are some in METAL2 / METAL3 and the gauge is not super-pitched.
* New: In NetBuilder, function isInsideBlockage(), to check if a
terminal is completely or partially enclosed in a blockage.
* Change: In NetBuilderHV::doRp_AutoContact(), remove support for
trying to put on grid misaligned METAL2/METAL3.
Instead systematically access them from above.
Do not cover with fixed protection terminals that are already
enclosed in blockages.
* Bug: In NetBuilderHV::doRp_AutoContact(), always add the terminal
contact in the requested GCell and not the target/source one,
in case the terminal span several GCells.
* Change: In NetBuilderHV::doRp_Access(), create the local wiring
according to the RoutingPad layer.
* Change: In NetBuilderHV::_do_xG(), _do_2G(),
create the global wiring in upper layers, according to the
ToUpperRouting flag.
* Change: In NetBuilderHV::_do_xG_xM3(), now delegate to
_do_xG_xM3_baseRouting() and _do_xG_xM3_upperRouting() if the
density at terminal level is above 0.5.
* New: NetBuilderHV::_do_xG_xM3_baseRouting() and
_do_xG_xM3_upperRouting() separated function to manage the
local routing.
* Change: In NetBuilder::_do_globalSegment(), if the currently
processed GCell or it's source is in ToUpperRouting mode,
move up the global segment. Do *not* use the moveUp() function
which would create doglegs unwanted at this stage.
* New: In KatanaEngine::annotateGlobalGraph(), call postGlobalAnnotate()
on the GCell after the blockages have been taken into accound to
add the penalty.
* Bug: In Track::getPrevious(), correctly manage the 0 value for the
index argument. Strange it didn't show earlier.
Same goes for Track::expandFreeInterval().
* Bug: In Anabatic::_desaturate(), the set of invalidated GCells was never
cleared between iterations of desaturated GCells. This was not a
memory leak per se because, in the end, the set was freed. But it did
induce a gigantic bloating in memory. This finally explain the strange
slow down in that stage.
Detected in ls180+cmos45.
* Change: In Anabatic::GCell, add a flag for each depth to avoid
desaturating twice the same GCell (maybe not needed now that the
bug is corrected, but it ensure a no-looping).
First part of the antenna effect protection : diode insertions.
Anabatic::antennaProtect(Net*) and it's supporting infrastructure
has been rewritten & simplificated. Must be used in conjuction
with the "Flexlib" bloat model of Etesian. A cursory description
of the algorithm has been added in the source file.
* New: GCell::hasNet() to tell if net is going through a GCell,
either as a straigth wire or has a local GContact (turn,
branch, terminal).
* New: Etesian::BloatFlexib class (tagged "Flexlib") suited for
flexlib uses. It is derived from "nsxlib".
To have enough space to insert all the wanted diodes, we
enlarge "mx2_x2" & "mx3_x2" of resp. 1 and 2 pitches.
This is an empiric finding, Yosys seems very fond of thoses
gates and we often see them underneath area where no space
was available to put a diode... May need some more fine grained
analysis.
* Bug: In Anabatic::GCell::updateDensity(), the GoStraight flag is now
set in this function when the density of blockage is above 40%.
(should be parametrized in the future). This is linked with the
Katabatic TrackFixedsegment bug.
* Bug: In Anabatic::GCell::Key::Compare, the densities of the GCell
where sorted in the *wrong* order, that is *less denser first*.
This was making the layer assignment working on it's head.
WTF, how did it ever work.
Also sort on global saturation.
* Change: In EtesianEngine::globalPlace(), disable the call to
antennaProtect(). First reason is that, after all, Coloquinte
do not handle so well the resizing of the cells "on the fly",
it overspill the boundaries sometimes. Second reason is that
as we cannot know the routing tree at this stage, we will not
be able to choose the correct points for diode insertions.
We only have a Steiner tree wich may not be the same as a
density driven Dijkstra.
* Change: In Etesian::Area, the Occurrence to the Instances where
not stored in a uniform way. Some where starting from the
placed sub-block, some where starting from the top level
(corona), making their processing (and remembering it) tricky.
Now, they are all expressed from the top cell (corona).
The coordinate system is now systematically the one of the
top block (*not* the block).
Create various overloaded functions EtesianEngine::toCell()
and EtesianEngine::toBlock() to ease Occurrence & coordinate
translations.
* New: In Etesian::Slice::createDiodeUnder(), add a X position hint.
Search is done by going through the whole slice range and
minimizing the distance to the hint. If it starts to be too
slow, we may optimize.
* Bug: In EtesianEngine::toColoquinte(), the placement of the top
level external pins was not taken into account (this at last
explain their weird positioning).
* New: AnabaticEngine::antennaProtect(), new algorithm to avoid
antenna effect. This step must be done *after* global routing
and *before* detailed routing. This way we have access to the
real routing and can mend it (along with the netlist) to
insert diodes at the rigth points.
From the global routing we build clusters (DiodeCluster) of
RoutingPads connected through a set of wire whose total length
is below the antenna effect threshold. Long wires connecting the
clusters are also tagged because we need to put a diode between
them and the first RoutingPad of the cluster. This is to avoid
a long METAL2 wire connecting to the RoutingPad before the diode is
connected through METAL3 (in case of misalignment).
This protection is not even enough. For *very long* wires, we
needs to put *more* than one diode (this is to be implemented).
* Change: In AnabaticEngine::_desaturate(), now use a STL priority
queue built upon a vector with duplicates of the GCell keys.
Much much more faster than the previous set with a custom
sorting key over the GCell. Insertion & removal where getting
a lot of time. Now it's down to less than a minutes, even for
big designs.
* Change; In Anabatic::GCells, add the ability to clone the GCell
key, to use it independently in GCells sorting containers.
This way the cloned value do not change when the GCell is
updated. Keep track of the latest (most up to date) cloned
key.
This commit contains two set of features that should have been commited
separately.
1. Compliance with clang 5.0.1, tested with the RedHat collection
llvm-toolset-7. This allow Coriolis to be compiled under Darwin (MacOS)
with Xcode & macports. The bootstrap install system has been modificated
accordingly.
2. The basic support for routing density driven placement. Related
features are:
* Bloat property. Each Occurrence of an Instance can be individually
bloated. This property not attached to any tool to allow the placer and
router to share it as wanted. Nevertheless, it is defined in Etesian.
* BloatProfile in Katana, add individual Bloat properties to Instances
occurrences based on the East & North overflowed edges of each GCell.
* Support in ToolEngine for a "pass number" of a tool. This pass number
is mainly used to make "per pass" measurements. The MeasureSet system
is improved accordingly to support multiple values of a same measure.
* Embryo of "P&R Conductor" to perform the place & route loop until the
design is successfully placed. May be the first brick of a Silicon
Compiler.
* Change: In boostrap/FindBoostrap.cmake, in setup_boost(), added tag to
the python component for macport (ex: python27).
* Change: In boostrap/build.conf, put etesian before anabatic for
instance occurrence BloatProperty dependency.
Added option support for the "llvm-toolset-7" collection to build
against clang 5.0.1.
* Bug: In Hurricane::getRecord( const pair<T,U>& ), the getSlot<> templates
for first & second arguments must be called with <const T> and <const U>
as the pair itself is const (and not simply <T> & <U>).
* Change: In Hurricane::getSlot() temlate, only use "string" arguments and
not const string&, simpler for template argument deduction.
* Bug: In Hurricane::AnalogCellExtension, the StandardPrivateProperty<>
template has a static member "_name". Clang did show that the template
for this static number has to be put inside the namespace where the
template *is defined* (i.e. Hurricane) instead of the namespace where
it is instanciated (i.e. Analog).
* Bug: In Isobar, Matrix_FromListOfList(), PyInt_AsPlacementStatus() must
be put outside the C linkage back in the Isobar C++ namespace (clang).
* Bug: In Hurricane::DBo::~DBo, and derived add a throw() specification
(clang).
* Bug: In Hurricane::RegularLayer::getEnclosure() & setEnclosure(), change
signature so it matches the one of the base class (clang).
* Bug: In Hurricane::CellPrinter, use double brackets for initializer list
(clang).
* Change: In Hurricane::Breakpoint, reverse the meaning of the error level.
Only error level *lesser or equal* than the stop level will be enabled.
* Bug: In CRL/python/helpers/__init__.loadUserSettings(), must put the
current working directory in the sys.path as in certain configuration
it may not be included.
* Bug: In CRL::ApDriver, DumpSegments(), no longer generate segments when
encountering a RoutingPad on a top-level Pin Occurrence. The segment
was generated in the wrong direction, creating DRC violations on the
"mips_core_flat" example.
* Change: In CRL::Measures, partial re-design of the measurements management.
Now, each kind of measure can accept multiple values put in a vector.
The index is intented to match a tool run number.
* Change: In CRL::Histogram, add support for multiple sets of datas,
indexeds with tool run number.
* Change: In CRL::ToolEngine, add support for multiple pass number, add
addMeasure<> templates for the various data-types.
* Change: In CRL::gdsDriver & CRL::gdsParser(), comment out unused GDS record
name constants.
* New: Etesian::BloatProperty, property to attach to Instance occurrences
that contains the extra number of pitch to add to the cell width.
* Bug: In AutoSegment::CompareByDepthLength, the segment length comparison
was wrong, it was always returning true, which broke the "strick weak
ordering" of the comparison.
This was producing a core-dump in GCell::updateDensity() when sorting
a vector<>. The end() iterator was being dereferenced, leading to the
problem.
* Bug: In Katana::DataSymmetric::checkPairing(), the test for segments
whose axis is perpandicular to the symmetry axis was wrong
("!=" instead of "-").
* New: In Katana/GlobalRoute, new ::selectSegments(), selectOverloadedgcells()
and selectBloatedInstances() to automatically select segments from
overloaded edges, overloaded GCells and bloated cells.
* Change: In KatanaEngine, return a more detailed success state, distinguish
between global and detailed.
Add support for multiple routing iterations.
* New: In cumulus/python/plugins/ConductorPlugin.py, embryo of routing
driven placement.
* Change: In Anabatic::GCell::updateDensity(), all non-passthrough wires
now have a cost of 0.5 instead of 0.33 for locals.
* Change: In Manipulator::canMoveUp(), increase the "reserve" amount to
1.0 for "far from terminal" wires (rpDistance > 2).
* Change: In NegociateWindow::NegociateOverlapCost(), always sets "AtRipupLimit"
when the overlapping segment is nearing it's maximum ripup limit.
(different detection for non-preferred and regular)
* Change: In SegmentFsm::_slackenStrap(), call avoidBlockage() if it is
overlapping a blockage *or* a segment at it's ripup limit. I hope I
didn't create an infinite loop here.
* Bug: In cumulus/plugins/PadsCorona.py, CoreWire._computeCoreLayers(),
the big contact between symbolic and real was badly computed for
east/west (was using width instead of height, bummer!).
In Corona._createCoreWire(), completly screwed computation of the
side gap, was using a badly initialized value of the "bb" variable.
* Bug: In cumulus/plugins/Chip.py, the computation of the minimal size
for the corona was wrong, do *not* add the size of the pads and
multiply by two as it is done by "inflate". This was forcing the user
to create way to large chips for a given core size.
This commit degrades the run success rate of ARMv2a to 87% (40 iters).
* New: In CRLcore/etc/.../kite.conf, add configuration parameters:
katana.termSatReservedlocal
katana.termSatthreshold
for the new edge capacity computation system.
* New: In CRLcore/etc/symbolic/phenitec06/, add support for N. Shimizu
small I/O pads (supplied in phlib80). Tune various parameters of
Anabatic/Katana to increase routing success.
* Change: In CRLcore/alliance/ap/ApParser, make Pin external components,
so RoutingPad will be build upon in global routing.
Do not complain when a I/O pad has a physical instance that did
not exists in the netlist. Just create it (appeared in phlib80).
When no netlist instance exists in a pad, the pad Cell is still
considered as terminal.
* New: In Etesian::BloatCells, new profile named "3metals" better suited
for two routing metals technologies (i.e. Phenitec).
* New: In Anabatic::RawGCellsUnder, new CTOR which take only source &
target points instead of a segment. Needed to manage wide segment for
which the axis to consider is not that of the segment (one axis for
each track it intersect).
* New: In Anabatic::GCell, add a RoutingPad count attribute, for Edge
reservation computation.
* New: In AnabaticEngine::computeEdgeCapacities(), instead of decreasing
all edges of a fixed amount (hTrackReservedLocal), guess the GCell
cluttering from the number of RoutingPads that it contains.
For non-saturated GCells, the four edges are decreased by the number
of RoutingPads. We use the maximum from the two neigboring GCells.
The hTrackReservedLocal parameter is now used only as a *maximum*
that the edge reservation can reach.
If a GCell is saturated (more than 8 RoutingPads, the saturation is
propagated horizontally to 2 neigboring GCells).
* Change: In AutoContactTerminal::getNativeConstraintBox(), use a more
flexible gauge name matching for terminal vertical extensions correction.
Namely, match all "msxlib*" kind of gauges.
* Change: In AutoSegment::setAxis(), add the ability to force the axis
position, even if it is a non-canonical segment. Maybe needed in the
initialisation steo, before the first canonisation is performed.
* New: In NetBuilder, added new methods _do_1G_1PinM1() and _do_2G_1PinM1(),
to manage coronas for Phenitec designs.
To avoid various side effects from segments being too close from
the north / east side of the routing area, make those segments fixeds.
* Change: In KatanaEngine::annotateGlobalGraph(), the management of wide
wires was wrong. The axis to use to find the underlying GCells is the
one of the track, not of the segment. This was creating bad edge
capacity computation under the power ring of a block and subsequently
routing failures.
* New: In Kanata::Manipulator, added method reprocessParallels(), not used
though, but keep it anyway, might be of use later...
* New: In Kanata::Manipulator, added method avoidBlockage() for terminal
METAL2 in non-preferred direction, restrict the terminal and turn
constraint box at the current position of the perpandicular, so it
doesn't create a deadlock in METAL2.
* Change: In SegmentFsm::conflictSolveByPlaceds(), if we cannot break
using the whole overlap, try the first atomic overlap.
* New: In SegmentFsm::_slackenStrap(), manage conflict between a non-prefered
segment and a blockage, this when to call avoidBlockage()...
* New: In Katana::Configuration, management of the new edge computation
parameters:
katana.termSatReservedlocal
katana.termSatthreshold
* New: In Cumulus/plugins/Core2Chip, support for Phenitec I/O pads.
* Change: In Hurricane::SharedName, replace the incremental Id by a hash key.
This is to ensure better deterministic properties. Between use cases,
additional strings may have to be allocated, shitfing the ids. Even if
hash can be duplicated, we should be able to ensure that the absolute
order in map table should be preserved. Supplemental strings are inserted
in a way that keep the previous order.
* Change: In CRL/etc/symbolic/cmos/kite.conf, add "katabatic.routingGauge"
default parameter value ("sxlib").
* Change: In CRL/etc/common/technology.conf, define minimal spacing for
symbolic layers too (added for METAL4 only for now).
* Change: In CRL::Histogram, extend support to dynamically sized histograms.
Add a text pretty print with table and pseudo-curve.
* Change: In Cumulus/plugins/ClockTreePlugin, create blockage under the
block corona corners so the global router do not draw wire under them.
This was creating deadlock for the detailed router.
When the abutment has to be computed, directly use Etesian to do it
instead of duplicating the computation in the Python plugin.
* New: In Etesian, as Coloquinte seems reluctant to evenly spread the
standard cells, we trick it by making them bigger during the placement
stage. Furthermore, we do not not uniformely increase the size of the
cells but create a "bloating profile" based on cell size, cell name
or it's density of terminals. Currently only two profiles are defined,
"disabled" which does nothing and "nsxlib" targeted on 4 metal layer
technologies (aka AMS 350nm, c35b4).
* Bug: In Knik::MatrixVertex, load the default routing gauge using the
configuration parameter "katabatic.routingGauge" as the default one
may not be the first registered one.
* New: In AnabaticEngine::setupNetDatas(), build a dynamic historgram of
the nets terminal numbers.
* Bug: In Anabatic::AutoContact::Invalidate(), always invalidate the
contact cache when topology is invalidated. In case of multiple
invalidations, if the first did not invalidate the cache, later one
that may need it where not allowed to do so. The end result was correct
nonetheless, but it did generate annoying error messages.
* Bug: In Anabatic::AutoContactTurn::updateTopology(), bad computation
of the contact's depth when delta == 2.
* Bug: In Anabatic::Gcell::getCapacity(), was always returning the west
edge capacity, even for the westermost GCell, should be the east
edge in that case.
* New: In Anabatic::AutoSegment, introduce a new measure "distance to
terminal". This is the minimal number of segments separating the
current one from the nearest RoutingPad. This replace the previous
"strong terminal" and "weak terminal" flags.
This distance is used by Katana to sort the events, we route the
segments *from* the RoutingPads *outward*. The idea being that if we
cannot event connect to the RoutingPad, there is no points continuing
as thoses segments are the more constraineds. This gives an order close
to the simple ascending metals but with better results.
* New: In Anabatic::AutoSegment, introduce a new flag "Unbreakable", disable
dogleg making on those segments. mainly intended for local segments
directly connecteds to RoutingPads (distance == 0).
* New: In Anabatic::AutoSegment, more aggressive reducing of segments.
Now the only case where a segment cannot be reduced is when it is
one horizontal branch in a HTee or a vertical on a VTee. Check if,
when not accounted the source & target VIAs are still connex, if so,
allow reducing.
* New: In Anabatic::AutoContact, new state flags CntVDogleg & CntHDogleg
mainly to prevent making doglegs twice on a turn contact. This is to
limit over-fragmentation. If one dogleg doesn't solve the problem,
making a second one will make things worse only...
* Bug: In Anabatic::Configuration::selectRpcomponent(), we were choosing
the component with the *smallest* span instead of the *bigger* one.
* New: In Anabatic::GCell, introduce a new flag "GoStraight" to tell that
no turn go be made inside those GCells. Mainly used underneath a block
corona.
* New: In AnabaticEngine::layerAssign(), new GCellRps & RpsInRow to manage
GCells with too many terminals. Slacken at least one RoutingPad access
when there is more than 8 RoutingPad in the GCell (slacken or change
a vertical METAL2 (non-preferred) into a METAL3).
* Change: In Anabatic::NetBuilderHV, allow the use of terminal connection
in non-preferred direction. That is, vertical METAL2 directly connected
to the RoutingPad (then a horizontal METAL2). This alllows for short
dogleg without clutering the METAL3 layer (critical for AMS c35b4).
Done in NetBuilderHV::doRp_Access(), with a new UseNonPref flag.
Perform some other tweaking on METAL1 access topologies, to also
minimize METAL3 use.
* New: In AnabaticEngine::computeNetConstraints(), also compute the
distance to RoutingPad for segments. Set the Unbreakable flag, based
on the distance and segment length (local, short global or long global).
New local function "propagateDistanceFromRp()".
* Change: In AnabaticEngine.h, the sorting class for NetData, SparsityOrder,
is modificated so net with a degree superior to 10 are sorted first,
whatever their sparsity. This is to work in tandem with GlobalRouting.
* New: In Katana::TrackSegmentNonPref, introduce a class to manage segment
in non-preferred routing direction. Mostly intended for small METAL2
vertical directly connected to RoutingPad. Modifications to manage
this new variant all through Katana.
* Change: In Katana::GlobalRoute, DigitalDistance honor the GoStraight flag
of the GCell. Do not make bend inside thoses GCells.
* Change: In KatanaEngine::runGlobalRouter(), high degree nets (>= 10) are
routed first and whitout the global routing estimation. There should be
few of them so they wont create saturations and we want them as straight
as possible. Detour are for long be-points.
Set the saerch halo to one GCell in the initial routing stage (before
ripup).
* Bug: In KatanaEngine & NegociateWindow, call _computeCagedconstraints()
inside NegociateWindow::run(), as segments are inserted into tracks
only at that point so we cannot make the computation earlier.
* Change: In Katana::Manipulator::repackPerpandiculars(), add a flag to
select whether to replace the perpandiculars *after* or *before* the
current segment.
* Change: In Katana::NegociateWindow::NegociateOverlapCost(), when the
segment is fully enclosed inside a global, the longest overlap cost
is set to the shortest global hoverhang (before or after).
When the cost is for a global, set an infinite cost if the overlapping
segment has a RP distance less or equal to 1 (this is an access segment).
* Bug: In Katana::PowerRailsPlane::Rail::doLayout(), correct computation of
the segments extension cap.
* New: In Katana::QueryPowerRails::addToPowerRail(), add support for Pad.
* Change: In Katana/PreProcess::protectCagedTerminals(), apply the contraints
to any turn connected to the first segment of the RoutingPad so the
perpandicular constraints got propagated to the perpandicular segment...
* Change: In RoutingEvent, cache the "distance to RP" value.
* Change: In RoutingEvent::Key::compare(), sort *first* on distance to
RoutingPad, then layer depth. If both distance to RoutingPad is null,
then sort on segment length.
* Change: In RoutingEvent::_processRepair(), try a repack perpandicular with
perpandiculars first (then with perpandicular last, then give up).
* Change: In SegmentFsm::bindToTrack() and moveToTrack(), set an axis hint
when creating the insertion event.
* Change: In SegmentFsm::_slackenStrap(), add a step through slacken between
minimize and maximum slack (wihch directly end up in unimplemented).
* Change: In Session::_addInsertEvent(), add an axis parameter needed when
the axis of the segment is not the one of the track (case of wide
segments or non-preferred direction).
* Bug: In Track::_preDestroy(), bad management of the TrackElement reference
count. Destroy the segment only when reaching zero...
* Bug: In Track::expandFreeIneterval(), forgotten to manage case when there
is a set of overlaping segments at the "end" of the track, the
EndIsTrackMax was not set.
* Change: In TrackCost::Compare, increase the cost when an overlaping
segment is at it's ripup limit. We should try *not* to rip it up if
we can. Add a dedicated flag "AtRipupLimit".
* Change: In TrackElement, add proxies for isUnbreakable(), new function
updateTrackSpan().
* New: In TrackFixedSegment CTOR, when a supply wire of METAL2 or above is
found, make the underlying GCells "GoStraight".
* New: In TrackElement::canDogleg(GCell*), check for already done perpandicular
dogleg on source/target (reject if so).
* Bug: In Anabatic::Edge::getDistance(), remove the additionnal 0.1
added to horizontal edges. This was for testing before the hScaling
parameter was added (to the distance computation in GlobalRoute).
* New: Anabatic::Path_Edges, collectio to walkthrough all the edges
between two node. More complex than in Knik as we are no longer
using a regular grid. We may request the north bound path or south
bound path.
Collection returned by AnabaticEngine::getEdgesUnderPath().
* New: In Anabatic::NetData, add a new flag GlobalEstimated to tell if
the net RMST has been computed (using FLUTE).
* New: In Anabatic::PriorityQueue, used to sort Vertexes by increasing
distances, add a new criterion to be used in case of distance
equality. The attractor which should be the center of the search
area. In case of equality, we choose the Vertex which is closest
to the attractor. Give a small improvement, and more "dendritic"
trees.
For a more simple implementation of the comparison function it is
made as a static member (so no two Dijkstra objects at the same
time...).
* Change: In Anabatic::Edge, make the estimate occupance a floating
point number instead of an integer.
* New: In Katana::GlobalRoute, finally implement the estimated congestion
driven router. Net RMST estimated using FLUTE.
Use the historic cost from Knik implementation and not the one
given in Damien's thesis, which seems not be the same and a bit
strange.
* New: In KatanaEngine, add the ability to exclude nets from routing,
and export it to Python.
* Bug: In Anabatic::AutoSegment::_changeDepth(), GCells under the segment
must be invalidated in order for the density to be recomputed.
But we were using GCell::invalidate() which is meant for the quad-tree
and graphic system, so the density almost never updated in case of
a layer change, leading to over-congested GCells in the top layers
(110% !).
Now we directly set the Invalidated flag.
* Bug: In Anabatic::Dijkstra, the degree of a vertex (the number of neighbors
belonging to the same net) was miscalculated. This was leading, in the
materialize step to some feed-through vertexes not being broken.
Leading in turn to incomplete transformation of the detailed routing.
Also in _trackback(), the degree of the first vertex we were backtracking
from was not incremented.
* Bug: In Anabatic::Dijkstra::materialize(), systematically use
GCell::breakGoThrough() on both source and target. This is needed when
we are in the ripup phase as both source and target can be go-through.
This was also leading to incomplete detailed routing transformation.
* Change: In Anabatic::Edge::ripup(), ripup one third of the segments instead
of thoses exeeding the global length threshold. This way we are sure to
desaturate an edge. Needs to be further calibrated.
* Change: In Aanabatic::GCell::breakGoThrough(), no longer return NULL.
Return existing gcontact if any. Break if it is a go-through and create
a new gcontact in last resort. Maybe rename this function.
* New: In Anabatic::Configuration, new parameters:
- anabatic.edgeHScaling, to adjust the length of the horizontal edges
relative to the vertical ones (this is a ratio).
- anabatic.globalIterations, set the maximum number of ripup passes
of the global router.
* New: In CRL/etc/*/kite.conf, added new parameters anabatic.edgeHScaling
and anabatic.globalIterations.
* New: In Katana::GlobalRoute::DigitalDistance, take into account the new
edgeHScaling factor. Must be used when the capacity of V-edges differs
greatly for H-edges (case of AMS 350nm c35b4 for instance).
* Bug: In Katana::GlobalRoute::DigitalDistance, the historic cost is
computed for an edge length of "1". Must be multiplicated by the
current edge length to have any measurable effect.
This bug is finally explaining why the ripup was producing the
same solutions over and over, the historical cost was negligible!
* Change: In Anabatic::GCell::doGrid(), the GCell where square using the
slice height as side. This was leading to vertical edges with slightly
different capacities when the vertical picth was not a multiple of
the horizontal one. This was not a bug per se as the global router
is able to manage any interval.
Now the horizontal side is rounded on the slice step.
* New: In Hurricane::Entity, add an id counter limit and a memory size
limit. The two limits are checked only when a new Entity object is
created. This should help avoiding massive memory links.
* New: In CRL Core, add a "crlcore.groundName" and a "crlcore.powerName"
parameter to specify the name of the ground/power signals to be
created if they are missing in a Cell. For Alliance libraries it
would be "vss" & "vdd" (default values), but for real technologies,
it is often "gnd!" & "vdd!".
The Blif parser is modificated to make use of it.
* Bug: In AnabaticEngine::unify(), set the resulting unified segment in
the center of the GCells common side. Gcells under a segment are
found by using the edge that cover the segment axis. When we have
a "bend" GCell stack and the axis is wrong, they could be ommited.
This was causing deleted segments to be not removed from some
Edges, then core dump.
* Change: In Anabatic::AutoSegment::create(), smarter choosing of the
reference contact, select the fixed or terminal one instead of
always the source one.
* New: In Anabatic::Edge::isEnding(), new function to check if a
segment going through an Edge is starting/ending in either source
or target GCell of the edge (active only when running in channel
mode).
* New: In Anabatic::Edge::add(), a segment takes part in the occupancy
only if it is not ending in either source or target (channel mode
only). The occupancy due to terminal is pre-computed in Katana.
* New: In Anabatic::Edge::ripup(), in channel mode, never ripup a
segment which is ending in either source or target (we *have* to
access this edge to connect to the terminal).
* Bug: In Anabatic::GCell::hcut() and vcut(), force the update of
the Edge which is on the side that will get splitted by the cut.
It's capacity will be reduced to it must be updated.
* Change: In Anabatic::GCell::updateGContacts() add a flag to conditionnally
update horizontals or verticals only. We may require only a partial
update when resizing the GCell in only one direction.
This, again, related to the fact that we compute the GCells under
a segment thanks to it's axis position, so we need to be very careful
when modificating axis.
* Change: In Katana::Block::resizeChannels(), only update GContact vertical
position. Do not disturb X positions of segments.
* Bug: In Katana::GlobalRoute::DigitalDistance, in channel mode, some
Edges can have a zero capacity, but still be reachable if the net has
a terminal in either source or target. Look for this case and return
a distance of zero instead of "unreachable". This was causing the
global routing not to complete in channel mode.
For computing the edge distance, makes the vertical edges much more
long (10 times) than the horizontal ones as the vertical capacity is
very limited. Hard coded for now, should make it a parameter in the
future.
* Change: In KatanaEngine::annotateGlobalGraph(), decrease the capacity
of edges with reserveCapacity for each terminal inside a GCell.
Both north and south edges are decreased as we a terminal will
block both north and south edges.
As a counterpart, the Edge capacity is not decreased when the
global router connect to a terminal.
* Change: In Katana::RoutingEvent::revalidate(), when in repair stage,
do not expand the slack for horizontal segments in channel mode.
So they may not overlap the standard cell row.
* Bug: In Stratus documentation, do not use the french option in babel,
the documentation is in english!
* New: In Documentation, added Hurricane/Python tutorial, part for drawing
layout.
* New: In Anabatic::Edge::ripup(), sort edges to ripup by decreasing
length so the longest gets riped up first.
In two metals mode, ripup all segments *except* those who have
terminal contact in the GCell, because they must use it anyway.
* Bug: In Anabatic::GCell::getEdgeAt(), the size hint flag was not
correctly selected, leading to the use of an edge in the wrong
side. So deleted segments where not deleted from their edges,
leading to core dump. Don't understand how it can have not shown
until now.
* New: In KatanaEngine::annotateGlobalGraph(), for two metal gauges,
decrease the edge capacity on both north and south side for each
terminal in the GCell. As a terminal must be accessed through
north or south it blocks the whole vertical track (hence both
edges).
* New: In Anabatic::EdgeCapacity, dedicated object to manage the capacities
of an edge by layer. This needed now because with real technologies
layers capacities differs (unlike with symbolic technologies).
This object is separated to be shared between Edges with identical
characteristics (direction+interval). Deletion is automatic and
done through refcounting. All the already allocateds EdgeCapacity
are kept into a set in the AnabaticEngine (key is (direction,interval)).
* New: In Anabatic::Edge, capacities are stored in a shared EdgeCapacity
object. The total capacity can be annotated (i.e. decreased).
EdgeCapacity attribute is created during the materialize() call.
The capacities are computed at this time.
The incCapacity() function is renamed in reserveCapacity().
* New: In Anabatic::AnabaticEngine, added attribute _edgeCapacitiesLut
to store the shared EdgeCapacity.
Lookup/Creation of an EdgeCapacity is done through _createCapacity().
* Change: In Anabatic::Constants, rename Flags::IllimitedCapacity into
Flags::InfiniteCapacity. Add Flags::NullCapacity (both for Edges).
* Change: In Anabatic::GCell, implement a by depth (for layer) getCapacity().
This modification did expose a bug in the density calculation :
per depth density where divided by the complete density instead of the
density's depth. This was leading to greatly underestimated densities.
Thoses underestimations where preventing Dijkstra and layer assignement
to manage congestion correctly (in fact, it was acting as if there
never was congestion).
Also avoid a divide by zero (thus -NAN showing in densities).
* Change: In Anabatic::GCell, rename setEdgeOccupancy() into the more
accurate forceEdgesCapacities().
Note for Eric: only the first Edge on each side has it's capacity
forced. What if there's more than one Edge ?
* New: In Commons, inspector support for std::pair<T,U>.
* New: In Hurricane::Layer, ContactLayer & ViaLayer, support for non
square VIAs. The hole (cut) remains square, but the various metal
extensions can now be different in X and Y. The ::getEnclosure()
method now takes a flag EnclosureH / EnclosureV.
* New: In Hurricane::DbU, inspector support for:
std::pair<DbU::Unit,DbU::Unit>
std::array<DbU::Unit,3>
Must be defined here as DbU do not exists yet in Commons.h
* Bug: In Hurricane::Interval::getSize(), when the interval is "full span",
do not return the difference between min and max, but directly DbU::Max.
(the previous result was -1 !)
* New: In CRL Core Python/Technology.py, support for non square VIAs in
the configuration files. Applied to FreePDK 45.
* New: In CRL::RoutingGauge, added a "symbolic" flag to tell if a gauge
is for symbolic layout or not. Exported to Python.
* New: In Anabatic::AutoHorizontal::updatePosition(), differentiated
computation for soure or target taking account of the VIA extension
in the right segment metal (due to non-square VIAs).
* Change: In Anabatic::AutoHorizontal::_makeDogleg(), the dogleg is
UP for HV gauges and DOWN for VH.
* New: In Anabatic::AutoSegment::_initialize(), create a cache of the
various extension length for each layer (viaToTop, viaToBottom,
viaToSame).
New implementation of getExtensionCap() using the previous cached
extension table. See updatePositions().
New static functions to access the extension cache in the header:
getViaTotopCap() ...
* Change: In Anabatic::AutoSegment, in various update methods, updateOrient()
must always be called *before* updatePositions() as extensions are
dependant on source/target.
* New: In Anabatic::AutoSegment::getEndAxes() compute the position of the
first source and last target position (center/axes) on an *aligned*
set of segments.
* New: In Anabatic::AutoSegment, add a new state flag SegAxisFixed to
signal segments that can be put on only one track. Specific case
to VH gauge for a M1 vertical terminal with a M2 vertical segment.
The M2 is effectively bound to the M1 axis position.
* Bug: In Anabatic::NetBuilderVH::_do_xG_xM1_xM3(), in case of E/W global
and only one RoutingPad the connexion to the RoutingPad was duplicated.
It was valid, but totally stupid.
* Bug: In Anabatic::Session::_canonize(), for an aligned segment set,
intersect the user constraints from all segments instead of only
considering the canonical one.
Issue a warning about too tight constraints only for symbolic
gauges. It may be correct for the real ones.
* New: In Katata::DataNegociate::update(), more accurate computation
of the perpandicular free interval. Use segment extension cap
calculation. Create a special case for fixed axis segments allowing
them to find alternative free interval, try under source and under
target as they are likely to be draggable segments.
* Change: In Katana::Manipulator::relax(), use the extension cap value
to compute the axis of the perpandicular segemnts.
* Change: In Katana::Manipulator::moveUp(), now move up the whole set
of aligned segments instead of just the canonical one.
* Change: In Katana::NegociateWindow::loadRoutingPads(), more accurate
TrackMarkers insertions for fixed terminals.
* New: In Katana::RoutingEvent::Key::Compare::operator(), segments with
fixed axis are processed prior to any others.
* New: In Katana::RoutingEventLoop, store segment pointers instead of
ids to generate more accurate error messages.
* Change: In Katana::RoutingPlane::create(), perform local track
assignment only for HV gauges.
* Change: In Katana::SegmentFsm::_slackenLocal(), add a "dragMinimize"
step in the automaton. Mutliple states transitions can occurs in
a row if an action fails.
* New: In Katana::Session::_toIntervalAxis(), normalize interval
bounds so they are on track positions (by shrinking the interval).
* Bug: In Katana::TrackMarker CTOR, the weigh computation was wrong.
* Change: In Anabatic::GCell::doGrid(), remove the "3 slice height"
limit (for small digital analog blocs).
* Bug: In Anabatic::NetBuilder::setStartHook(), perform a check for
a RoutingPad still on a Plug. Diplay an error instead of crashing.
* Bug: In CRL::RoutingLayerGauge::getTrackIndex(), the upper bound
of the track interval must be included instead of excluded.
* New: In Hurricane::Cell, add a StayOnPlugs flags for flattenNets().
To keep the RoutingPad occurrences on Plug instead of selecting
physical components.
* New: In Isobar::PyNet, add setAutomatic() and isAutomatic() to the
interface.
* Bug: In Katana::protectRoutingPads(), do not create protections on
PinOnly layers (mostly metal1).
* New: In AnabaticEngine::invalidateRoutingPads() this method is a temporary
workaround for a Hurricane problems. When an instance is moved, the
RoutingPads that use it must be moved accordingly, but they are not
invalidated so they stay in the wrong QuadTree.
New method ::_resizeMatrix() to be called when the associated Cell
is resized.
* Bug: In AutoHorizontal::getConstraints() and AutoVertical::getConstraints(),
the *target* constraints where never merged.
* Change: In AutoHorizontal::getCells() and AutoVertical::getGCells(),
now return a boolean to tell if it was ok (must not encounter a NULL
GCell while progessing from source to target).
* New: In Anabatic::Configuration and Anabatic:Session, create new methods:
- getDHorizontalLayer()
- getDhorizontalDepth()
- getDHorizontalWidth()
- getDHorizontalPitch()
And so on for Vertical and Contact.
They supply depth-independant informations about the H/V layers to
build the initial detailed routing.
The AutoSegment::create() methods have been modificated accordingly.
* New: In Anabatic::GCell, add two new types "StdCellRow" and "ChannelRow"
for implementing 2-Metal blocks.
Rename the GCell::setXY() method in GCell::setSouthWestCorner(),
move the contents of GCell::updateContactsPosition() into it and
suppress it.
WARNING: In case of a GCell shrink this may cause problems. But for
now we only expand...
New method GCell::getNetCount() to count the number of Net going
though the GCell.
* Change: In Anabatic::Edge, add specific support for capacity of 2-Metal
routing channels.
* Change: In Anabatic::Dijsktra various methods, replace the "gcell->isMatrix()"
calls by "not gcell->isAnalog()". Add more check so that the methods
pertaining to the analog routing (GRData) are not called in digital
mode.
* New: In Anabatic::Dijkstra::materialize(), add support for 2-Metal specific
cases. That is, always break in case of vertical pass-through or
U-turn. The global routing must always be broken in H-Channel.
* New: In Anabatic::GCell & Anabatic::Edge, make use of the Session mechanism
to ensure the revalidation. The "::revalidate()" method is then moved
as "::materialize()" (overload of Go) and "::_invalidate()" becomes
"::invalidate()"
* Change: In LoadGlobalRouting, cosmetic rename of SortHkByX in SortHookByX.
* New: In GCellTopology, added support for building 2-Metal topologies.
* ForkStack is now an object attribute as many methods do need it.
* To push segments/hook on the stack, a new method "push()" is
available. Perform NULL and fromHook checking. Can also setup
_southWestContact or _northEastContact if it is the "from" edge.
* N/S/E/W edges are now vector as in digital channel mode there
can be more than one.
* Added build topological build methods:
- doRp_2m_Access() RoutingPad stem access.
- _do_2m_1G_1M1() North or south access.
- _do_2m_2G_1M1() North AND south access.
- _do_2m_xG() H-Channel routing.
* New: In Anabatic::Matrix, new ::resize() function, as Cell can be resizeds.
* New: In Anabatic::Vertex, new static method ::getValueString() for a
friendly text rendering.
* New: In Katana::DigitalDistance, support for channel routing.
* Change: In KatanaEngine::digitalSetup() and KatanaEngine::runGlobalrouter(),
for channel routing, calls to setupPowerRails() and
protectRoutingPads() must be called after the core block has
been fully dimensionned.
::runGlobalrouter() contains the code tasked with the grid creation
and channel sizing.
* New: In KatanaEngine: Added support for core block, for 2-Metal routing.
May be expanded for over-the-cell routing in the future.
Added methods :
- isDigitalMode()
- isAnalogMode()
- isMixedMode()
- isChannelMode()
- getBlock() / addBlock()
- setupChannelMode()
- createChannel()
* New: In Katana, new class Block to manage core blocks and perform
channel routing.
* New: In Katana::Session, new convenience method "isOpen()".
in Dijkstra.cpp/.h, Edge.cpp/.h, GCell.cpp/.h:
*Change: GlobalRouting wires can have different wires' width. One Net's wires has one width only.
in NetRoutingProperty.cpp/.h, PyNetRoutingProperty.cpp/.h:
*New: A wire width parameter is added. It can be set through python script.
* New: In Anabatic_AutoSegments collection, added a Flag to the constructors
to allow different behavior between digital and analog modes.
For "Aligneds" and "Perpandiculars" collections, now manage a new
Flag WithDoglegs to follow aligned globals through local doglegs
(for analog nets).
Adjust the log level of collections to 144 (formerly 145).
* New: In Anabatic::AutoSegment, new flag SegAnalog for segments that are
part of an analog net.
Note that with this flag, we reach the 32 bits limit...
* Change: In Anabatic::Constants, Flags are now declared as BaseFlags
objects and *not* uint64_t. This avoids overload resolution problems with
arithmetical overload of the operators.
The BaseFlags/Flags types are now completly "isolated" from the
uint64_t, it has the advantage of showing where unwanted previous implicit
conversions where occuring.
* Change: In Katana::Constants, Flags values are now of BaseFlags type instead
of uint64_t.
* Change: In Anabatic::Dijkstra, lots of log cleanup.
* Change: In Anabatic::GCell::getSide(), make the "shrink" parameter visible
to allow to substract the topmost and rightmost track for axis span
computation in AutoSegment::computeOptimal(). Used for analog mode.
* Change: In NetRoutingState, added a flag for analog mode. Use uint32_t
for the flags type.
* New: In Isobar, export the NetRoutingState and NetRoutingExtension objects.
* Change: In Anabatic::AutoSegments collections, change the type of all
the flags that where in "unsigned int" (32 bits) to Flags (uint64_t)
as there is now more than 32 flags for functions.
* New: In Ababatic::Constants, added new flag Flags::WithPerpands, which
makes the number of flags tip over 32 bits, thus making mandatory
to uses Flags and not unsigned int.
* New: In Anabatic::AutoSegments_Perpandiculars, manage a new flag
Flags::WithDoglegs to allow to propagate through global segments that
are connecteds via doglegs on local segments. Meaning that there is
a good chance that they could be aligned.
Slighly change the way we propagate on aligned segments: no longer
check for VTee or HTee, but only for same direction and layer as
master.
* New: In Anabatic & Katana, replace all the "int", "long" and their
variants by the less implementation ambiguous "int32_t", "int64_t"
(and variant). This should help to better detect bit trucation in
flags.
Use the type to give a hint about the flags kind:
- Type "Flags", for flags shared among Anabatic & Katana
functions/methods (may also appear in some objects states).
- Type "uint32_t" for flags belonging to an object internal
state of from Hurricane functions flags (those should be
grouped in a Flag subclass in a perfect world).
* Bug: In Anabatic::RawGCellsUnder, *again*, the north and east borders
of the whole area *are* includeds (shut up disgraceful warning).
* New: In Anabatic::GCell, add a display mode to select between boundary
display (for analogic) and density display (for numeric).
* Bug: In KatanaEngine::runGlobalRouter(), do not check if an Edge cannot
be desatured when the vector or overloaded Edges is empty.
(one less disgraceful warning)
* New: In GraphicKatanaEngine::drawGCell(), support for drawing the GCells
in density mode. Use the fire scale and the MaxDensity mode.
Setup the GCell drawing mode in GraphicKatanaEngine::initGCell().
* Change: In GraphicKatanaEngine::drawEdge(), adjust the various thresholds
for showing the Edge and its label.
* New: In CRL Core, adds "anabatic.gcell.displayMode" to the set of Anabatic
parameters.
Adjust the showing threshold for GCells in "display.conf" so when the
zoom level is low, we still can see the density map.
* Bug: In Anabatic, in AutoHorizontal & AutoVertical, native constraints
must use GCell::getConstraintsUMax().
* Bug: In Anabatic::GCell, correct terribly bad implementation of
both getConstraintUmax().
In getSide(), use getConstraintUMax().
* Bug: In Anabatic::AutoContact, setCBUMax() must be set using the GCell
getContraintUMax().
* Bug: In Anabatic::GCell, new functions getConstraintUMax() to return the
correct bounding box for the last north/east GCell. The GCells do not
own their north/east edges, except for the last ones. Thoses functions
must distinct from getUMax() because for them, the shrink is always
applied. getConstraintBox() uses the "getConstraintUMax()" functions.
* Bug: In Anabatic::AutoContact, initialize the constraint box from the
new GCell::getConstraintUMax(), to manage correctly the boundaries
of the nothernmost & easternmost GCells. The problem was showing for
pins on the north/east side of a circuit, the constraint
* Bug: In Anabatic::AutoContactHTee, Anabatic::AutoContactVTee and
Anabatic::AutoContactTerminal forgot to call the _preCreate() function
in the various create().
* Bug: In Matrix::getUnder(), if on the N/E boundary, decrease by one to
be enclosed in it.
- Modified: Matrix is now correctly updated for irregular floorplans.
Dijkstra:
- Modified: Source and Target contacts are now correctly chosen in _materialize.
* Bug: In Hurricane, in StaticObservable::getObserver(), if the slot
pointer is NULL, do not try to access the owner. Returns NULL, so
the caller can be aware of the situation...
* Change: In Hurricane, in BreakpointWidget & ExceptionWidget some
cosmetic changes (fonts and window sizes).
* Bug: In Anabatic, In AutoHorizontal::getConstraints(), take into account
the constraints from the source AutoContact, as it holds the constraints
transmitted by the RoutingPads and sets up by propageConstraintsFromRp().
It is likely to be a bug affecting the original Katabatic as well.
* Change: In Anabatic, in RawGCellsUnder(), check that the segment is not
completly oustside the cell abutment box and truncate the coordinates
to the part that is inside. Use the "shrink" if we reach the east/north
border.
* Change: In Anabatic, in Configuration, no more decorator because we will
use a true derived relationship. Katana *derives* from *Anabatic* and do
not *decorate* it, so the Configuration can do the same. It also implies
that we directly create a Katana engine, not an Anabatic one.
* Change: In Anabatic, in Session, do not allow the opening of the Session
in a standalone fashion (with a static method). Instead it must be opened
using the relevant method of the Anabatic/Katana engine. This ensure we
are opening the right Session type.
* Change: In Anabatic, in AutoSegment_Aligneds() collection the seed segment
is not part of the collection by default, but will be included if the
Flags::WithSelf is set.
* Change: In Configuration, all the flags value are now defined in two steps.
Declared in the header and initialized in the module. This is to prevent
the fact that on some cases, in relation with the Python "extern C" part
modules, we need a true allocated variable. It was causing weird linking
problems.
A side effect is that they can no longer be used as entry is switches,
have to replace them by if/else.
* New: In Anabatic, new GCell::getNeighborAt() utility function.
* Bug: In Anabatic, in GCell::doGrid(), tag all the GCells of the grid with
the grid type... Back annote all the edges capacity (north & east) with
the reserved local capacity.
* New: Complete portage of Kite over Anabatic. The new engine is christened
"Katana" for Kite-Analogic. When it's capabilities and performances
will be on a part with Kite, it is to completly replace it (and take
back the "Kite" name). Preliminary tests seems to show that, contrary
to intuition (because built on a more complex/slower grid), it is even
slightly faster than Kite 8-).
* Bug: In Anabatic::GCell, when width and/or heigh is null, do not try to
compute densities as it will trigger a divide by zero (and do not make
much sense anyway).
* Change: In CRL Core, in cmos/alliance.conf, honor the ALLIANCE_TOP variable
if it is found in the user's environement.
* Change: In Anabatic:
- Long wires, going straight accross multiple GCells were splitted
into a long sequence of segment+contact, one for each gone-through
GCell. It was memory-consuming and algorithmically inefficient.
Now there is only one straight wire.
As a consequence, Edges now store the list of all segments
going through them. That way we do not need to load a Net into
Dijkstra before riping up some of it's segment. The ripup mechanims
can now be implemented right at AnabaticEngine level, without
dependencies over Dijkstra. Note that long wires are automatically
broken in two if we need to attach a new branch on it (breakAt()).
And fused back into one if a branch is removed (unify()).
* Bug: In Hurricane, in tstream (Commons.h), in the *template* overload of
operator<<(), do not use the operator<<() of ostream as it will be
looked up in "stage 1" (template definition) and so will miss all the
overloads added later and built over getString<>(). Instead, make use
of getString<>(), which, as another template will be looked up in
"stage 2" (template instanciation) and at that point will have all the
needed template specialisation of getString<>().
We also need to define new stream manipulators to be able to create
a matching template overload not dependant from the implementation.
To avoid name clashes, we prefix a 't'. For now, only 'tsetw()' is
refined.
As a side effect, we cannot directly print bit-fields into the stream,
we must go through an intermediate variable (happens once in AutoContact).
* New: In Anabatic:
- In AnabaticEngine, keep track of overflowed edges.
- In AnabaticEngine, getNetsFromedge() to lookup all nets going
through an Edge.
- In Configuration, read the Kite "reserved local" parameter to
decrease the Edge capacity (it's a guessing of the cost of the
local routing).
- In Edge, add an attribute to know if there is an associated
segment of the current net (set by Dijkstra::_traceback()).
Transparently manage the overflowed edges.
- In GCell_Edges, correct a filtering bug when not all sides are
selecteds.
- New GCell::getEdgeTo() to find the edge between two adjacent
GCells.
- New GCell::unrefContact() to automatically removes global contacts
no longer used by any global segments (used during the ripup
step).
- In Dijkstra::load(), now able to "reload" and already partially
or completly routed net (look for Contact of "gcontact" layer
and their attached segments).
- In Dijkstra, keep the last net loaded until the next one is.
Put the cleanup operations in an isolated function "_cleanup()".
- In Dijkstra::_selectFirstsource() and run(), load first source
component made of multiple vertexes.
- In Dijkstra::_trackback(), link the Net segments to the Edges.
- New Dijkstra::ripup(), Dijkstra::_propagateRipup() to perform
the ripup of one edge of a Net (must be loaded in Dijkstra first).
Dijkstra::_tagConnecteds() setup the connexId of a set of Vertexes
- that are connecteds through edges *with* segments.
- In GraphicAnabaticengine & GlobalRoute.cpp, embryo of a global
routing tool with ripup & reroute.
- (Add) HurricaneAMS includes
in Dijkstra:
- (Add+Modify) Handle restriction rules in Vertex for analog devices
in GCell:
- (Add) Check neighboring cells (North/South/East/West)
Jean-Paul Chaput
Myrtle Shah
EricLaoGitHub