Previously, the relevant NetBuilder and routing strategies where
directly guessed from the RoutingGauge traits. This is no longer
doable as the combinations increases. Now to configure both the
global and detailed router we need three "parameters" :
1. The routing gauge itself (tells which layers are in which
directions) and how to make the VIAs.
2. The NetBuilder to use, they are identified by strings.
Currently we support:
* "HV,3RL+", for all SxLib derived standard cells.
* "VH,2RL", for hybrid routing (over the cell, but terminals
are also in the first RL).
* "2RL-", for strict channel routing.
* "VH,3RL+", an attempt for FreePDK 45, not optimized enough
to be considered as usable.
3. The routing style, mostly affect the way the GCell grid will be
built.
* VH : first RL is V.
* HV : first RL is H.
* OTH : Run in full over-the-cell mode (needs at least 3RL).
* Channel : Run in *strict* channel routing mode (no routing over
the standard cells).
* Hybrid : Create channels, but can use H tracks over the
standard cells.
Thoses three parameters are partly overlapping and must be sets in
a consistent manner, otherwise strange results may occurs.
* New: CRL::RoutingGauge::getFirstRoutingGauge(), to get the lowest
layer available for routing (not a PinOnly, not a PowerSupply).
* Change: In CRL::RoutingGauge::isHV() and isVH(), were previously
always returning false when the gauge was 2RL only. Now, check
on the first usable RL.
* Bug: In cumulus/plugins.block.configuration._loadRoutingGauge(),
there was a bad computation of the deep RLs when the top layer
was not defined. Occured for 2RL gauges only.
* Bug: In Anabatic::RpsInRow::slacken() (LayerAssign), forgotten curly braces
in the test to skip METAL2 terminals.
* Change: In Etestian::BloatChannel::getDx(), adjust the bloating
policy to converge on Arlet6502. Always ensure that there is
a 50% ratio between terminal used V-tracks and free ones.
If there is more than 80% of terminals, add one more track.
* Bug: In AnabaticEngine & KatanaEngine, KatanaEngine is a derived
class of AnabaticEngine. They uses Anabatic::Configuration
and Katana::Configuration that also derives from each other.
I though I had made one configuration attribute in the base
class that was using the right Configuration. But no. I did
have two configurations attributes, one in AnabaticEngine and
one in KatanaEngine, the later "shadowing" the former. As a
results, parameters modified in AnabaticEngine, *after* the
initial creation of the tool *where never seen* at Katana
level (due to it's own duplicate). What a mess.
Now there is only one attribute in the *base* class Anabatic,
which is created through a new virtual function _createConfiguration()
called in _postCreate() which allocate the right Configuration
according to the dynamic type of the tool (KatanaEngine).
In KatanaEngine, access the configuration through the
attribute (_configuration) and not the accessor (getConfiguration()).
* Bug: In KatanaEngine, no longer directly use the _configuration attribute
(which is not accessible anyway) but the getConfiguration() accessor.
The accessor perform a static_cast from the Super::getConfiguration()
into Katana::Configuration.
Complete cleanup of the various configuration accessors.
* New: AnabaticEngine::setupNetBuilder(), perform an early check
of the requested NetBuilderStyle. The NetBuilderStyle is just a
string that will be matched against the (hard-coded) supported
NetBuilders. Then check the topological characteristics against
the capabilities of the gauge (HV, VH and so on).
Still a bit too hard-coded for now.
This function has been split from AnabaticEngine::_loadGrByNet().
* Change: AnabaticEngine::isChannelStyle() renamed from isChannelMode().
* New: In Anabatic::Configuration, two new attributes to select the
topology and routing style:
- _netBuilderStyle to explicitely select the NetBuilder to use.
It's a string, which is provided by each NetBuilder.
- _routingStyle to define how the overall routing will work.
It's a set of flags (StyleFlags):
* VH : first RL is V.
* HV : first RL is H.
* OTH : Run in full over-the-cell mode (needs at least 3RL).
* Channel : Run in *strict* channel routing mode (no routing over
the standard cells).
* Hybrid : Create channels, but can use H tracks over the
standard cells.
* New: In anabatic/Constants, add StyleFlags to define how the router
should operate (see above).
* Bug: In Anabatic::GCell, in CTOR, no reason to set up the HChannelGCell flag.
* Bug: In Anabatic::GCell::updateDensity(), when computing layers non contiguous
saturation, do not systematically skip RL 0, but only if it's PinOnly.
* Change: In Anabatic::NetBuilder, rename isTwoMetal by isStrictChannel.
* Change: In Anabatic::NetBuilderHV, rename doRp_AccessNorthPin() in
doRp_AccessNorthSouthPin(). More accurate.
* Bug: In NetBuilderHV::_do_1G_xM1_1PinM2(), the wires to connect the M1
terminals where created *twice*. Uterly stupid, there where placed in
overlap by the router!
* New: In AnabaticEngine, new accessors to the NetBuilderStyle and
RoutingStyle, proxies towards Configuration.
* Bug: In Manipulator::relax(), if there are two doglegs to be done, but
they are in the same GCell, only do one (the conflicting interval)
is short.
* Change: In Katana::Session, rename isChannelMode() into isChannelStyle().
* Change: In TrackSegment::isUnbreakable() and isStrap(), return false
when the base segment is a *weak global* (aligned with a global one).
* Change: In Katana::Row::createChannel(), correctly distinguish between
*strict channel* style and *hybrid* style. Tag the GCells as std cells
row or channels only in the former case.
* Update: In CRL/node600/phenitec/kite.py, update the routing gauge to
the new format. So now we can use again SxLib-2M (channel routing
SxLib for two metal technologies).
* Change: In CRL::BlifParser, if a master cell is not found in the
AllianceFramework, then try in the Blif supplied libraries.
This is used to load the zero, one and tie cells.
Add a Blif::getCell() static function to look into the Blif
supplied libraries.
* Change: In CRL::LefImport, sometimes there can be discrepencies between
the LEF ROUTING layers and the Coriolis routing gauge. Now ignore
routing layers that are *not* presents in the Coriolis gauge.
* Change: In AnabaticEngine, moved routingMode attribute from KatanaEngine,
as some setup operations needs it.
* Change: In AutoSegment::canReduce(), allow fixed segments to be reduced
if they are "jumpers" (turn+turn and top+top or bot+bot).
This case arise on the edge of routing channels for fixed wires
to connect terminals.
* Change: In AutoSegment::getTopologicalinfos(), compute differently the
(leftBound,rightBound) interval when in channel mode.
In over-the-cell mode, this interval is the one of the whole
GCells under the wire. In channel mode, for fixed wires (that is,
verticals connecteds to cells) this interval is reduced to half
the GCell height, on the connected side of said channel.
This allows Manipulator::_insertToTrack() to issue disantangling
requests (push left/push right) for fixed segments that are face
to face in the channel.
* Change: In Anabatic::Configuration CTOR, allow the cellGauge to have a
different name from the routingGauge. Now if the cell gauge that
should match the routing gauge is not found, fallback to the
name set in "anabatic.cellGauge" parameter.
Case occur when we try to match with CORE sites from LEF files.
* Change: In Etesian::Configuration CTOR, same change as in the
Anabatic configuration.
* Change: In Anabatic::GCell::updateDensity(), never set the GoStraight
flag in channel mode. This flag makes sense when there is at least
4 routing layers (so we have 2 contiguous free of blockages).
* Bug: In Anabatic::Session::_getNearestGridpoint(), sometimes the nearest on
grid point is outside the constraint box. Now force the point
to remains inside constraints even if offgrid.
* Change: In Katana::DataNegociate::update(), perpandiculars that are
either reduced or in non-preferred routing direction should not
trigger a bug message.
* Change: In KatanaEngine::_check(), do not check for fixed, horizontal
non-prefs AutoSegments in channel mode (avoid false bug display).
* Bug: In Manipulator::_forceToTrack(), slighty shrink (-1) the interval
to free. The intersection function of intervals returns true when
the two intervals *exactly* touches (1.vMax == 2.vMin). But in
this specific case, they are not *overlapping* and no action
should be taken...
* Bug: In Manipulator::_insertInTrack(), do not reject the track when
we are overlapping a fixed vertical segment in channel mode.
(Hmm, maybe already corrected by the previous one).
* Change: In Katana::NegociateOverlapCost(), in channel mode, do
not put two overlaping vertical fixed segments into infinite cost.
This happens when two cell connected verticals are face to face in
a channel. We want them negociated the track (by shrinking their
length) instead of excluding it right away.
* Change: In NegociateWindow::createTrackSegment(), in channel mode,
do not attempt to create a track segment over a fixed and reduced
AutoSegment.
Do not attempt to put a non-preferred AutoSegment on a Track
either.
* Bug: In RoutingEvent::revalidate(), the number of availables tracks
was badly computed when in the pure constraint case, when there
was only one it was reporting zero.
* Change: In TrackElements::TrackElements_Perpandicular::Locator,
do not issue a bug when an non-pref or reduced AutoSegment do not
have an associated TrackElement.
* Change: In TrackSegmentCost::update(), do not issue a bug when a
perpandicular is reduded or non-pref and do not have a TrackElement.
* New: In Katana::DataNegociate, add a "sameRipup" counter to keep
the *consecutive* number of time a segment is put in the same
track.
* New: In TrackSegment::setAxis(), update/reset the "sameRipup"
counter of the DataNegociate.
* New: In TrackCost, add new flag "Blacklisted" to mark Tracks that
have been riped up too much in a consecutive row.
TrackCost::Compare::operator() will then sort the blacklisted
track after the non-blacklisted ones.
* New: In SegmentFsm CTOR, raise the Blacklist flag on the TrackCost
if the "sameRipup" is above 10. This to get away from a state
well in the ripup.
* Bug: In Katana::DataNegociate::update(), when computing the length of
source & target extension on a perpandicular segment, must use the
extensions of the *directly* connected AutoSegment (the baseSegment)
and not the canonical one that may be different, so with unrelated
extensions.
NOTE: This is likely to explain why we still got overlap in the
track coherency check in very rare occasions.
* Bug: In Katana::DataNegociate::update(), when computing the allowed
free interval for the segment axis deduced from the perpandicularly
connex segments, we account for the extension of the connecting
VIA. Those extension varies according to the kind of VIA and are
given by getExtensionCap().
We were accounting for the source & target extension VIA on the
parallel segments, assuming that source/target would not swap when
the perpandicular is moved. Which is *not* true.
Now account for the extension of the *connecting* VIA on all ends.
* Change: In AutoSegment::getTopologicalInfos(), enrich the list of
perpandicularly connected segment with wether they are connex by
their *source* or *target* contact. Mainly to be used by
DataNegociate::update().
* In KatanaEngine:
- Former situation:
Each RoutingEvent did store the routing stage it was in. And it
was misnamed "mode".
- New organization:
The routing stage is stored in KatanaEngine itself. It can be
accessed through a proxy in Session.
* Change: In DataNegociate::update(), when in Realign stage and computing
non-preferred perpnadicular routing *do not* expand of one pitch
outside the RoutingPad range.
* Change: In Hurricane::SharedName, replace the incremental Id by a hash key.
This is to ensure better deterministic properties. Between use cases,
additional strings may have to be allocated, shitfing the ids. Even if
hash can be duplicated, we should be able to ensure that the absolute
order in map table should be preserved. Supplemental strings are inserted
in a way that keep the previous order.
* Change: In CRL/etc/symbolic/cmos/kite.conf, add "katabatic.routingGauge"
default parameter value ("sxlib").
* Change: In CRL/etc/common/technology.conf, define minimal spacing for
symbolic layers too (added for METAL4 only for now).
* Change: In CRL::Histogram, extend support to dynamically sized histograms.
Add a text pretty print with table and pseudo-curve.
* Change: In Cumulus/plugins/ClockTreePlugin, create blockage under the
block corona corners so the global router do not draw wire under them.
This was creating deadlock for the detailed router.
When the abutment has to be computed, directly use Etesian to do it
instead of duplicating the computation in the Python plugin.
* New: In Etesian, as Coloquinte seems reluctant to evenly spread the
standard cells, we trick it by making them bigger during the placement
stage. Furthermore, we do not not uniformely increase the size of the
cells but create a "bloating profile" based on cell size, cell name
or it's density of terminals. Currently only two profiles are defined,
"disabled" which does nothing and "nsxlib" targeted on 4 metal layer
technologies (aka AMS 350nm, c35b4).
* Bug: In Knik::MatrixVertex, load the default routing gauge using the
configuration parameter "katabatic.routingGauge" as the default one
may not be the first registered one.
* New: In AnabaticEngine::setupNetDatas(), build a dynamic historgram of
the nets terminal numbers.
* Bug: In Anabatic::AutoContact::Invalidate(), always invalidate the
contact cache when topology is invalidated. In case of multiple
invalidations, if the first did not invalidate the cache, later one
that may need it where not allowed to do so. The end result was correct
nonetheless, but it did generate annoying error messages.
* Bug: In Anabatic::AutoContactTurn::updateTopology(), bad computation
of the contact's depth when delta == 2.
* Bug: In Anabatic::Gcell::getCapacity(), was always returning the west
edge capacity, even for the westermost GCell, should be the east
edge in that case.
* New: In Anabatic::AutoSegment, introduce a new measure "distance to
terminal". This is the minimal number of segments separating the
current one from the nearest RoutingPad. This replace the previous
"strong terminal" and "weak terminal" flags.
This distance is used by Katana to sort the events, we route the
segments *from* the RoutingPads *outward*. The idea being that if we
cannot event connect to the RoutingPad, there is no points continuing
as thoses segments are the more constraineds. This gives an order close
to the simple ascending metals but with better results.
* New: In Anabatic::AutoSegment, introduce a new flag "Unbreakable", disable
dogleg making on those segments. mainly intended for local segments
directly connecteds to RoutingPads (distance == 0).
* New: In Anabatic::AutoSegment, more aggressive reducing of segments.
Now the only case where a segment cannot be reduced is when it is
one horizontal branch in a HTee or a vertical on a VTee. Check if,
when not accounted the source & target VIAs are still connex, if so,
allow reducing.
* New: In Anabatic::AutoContact, new state flags CntVDogleg & CntHDogleg
mainly to prevent making doglegs twice on a turn contact. This is to
limit over-fragmentation. If one dogleg doesn't solve the problem,
making a second one will make things worse only...
* Bug: In Anabatic::Configuration::selectRpcomponent(), we were choosing
the component with the *smallest* span instead of the *bigger* one.
* New: In Anabatic::GCell, introduce a new flag "GoStraight" to tell that
no turn go be made inside those GCells. Mainly used underneath a block
corona.
* New: In AnabaticEngine::layerAssign(), new GCellRps & RpsInRow to manage
GCells with too many terminals. Slacken at least one RoutingPad access
when there is more than 8 RoutingPad in the GCell (slacken or change
a vertical METAL2 (non-preferred) into a METAL3).
* Change: In Anabatic::NetBuilderHV, allow the use of terminal connection
in non-preferred direction. That is, vertical METAL2 directly connected
to the RoutingPad (then a horizontal METAL2). This alllows for short
dogleg without clutering the METAL3 layer (critical for AMS c35b4).
Done in NetBuilderHV::doRp_Access(), with a new UseNonPref flag.
Perform some other tweaking on METAL1 access topologies, to also
minimize METAL3 use.
* New: In AnabaticEngine::computeNetConstraints(), also compute the
distance to RoutingPad for segments. Set the Unbreakable flag, based
on the distance and segment length (local, short global or long global).
New local function "propagateDistanceFromRp()".
* Change: In AnabaticEngine.h, the sorting class for NetData, SparsityOrder,
is modificated so net with a degree superior to 10 are sorted first,
whatever their sparsity. This is to work in tandem with GlobalRouting.
* New: In Katana::TrackSegmentNonPref, introduce a class to manage segment
in non-preferred routing direction. Mostly intended for small METAL2
vertical directly connected to RoutingPad. Modifications to manage
this new variant all through Katana.
* Change: In Katana::GlobalRoute, DigitalDistance honor the GoStraight flag
of the GCell. Do not make bend inside thoses GCells.
* Change: In KatanaEngine::runGlobalRouter(), high degree nets (>= 10) are
routed first and whitout the global routing estimation. There should be
few of them so they wont create saturations and we want them as straight
as possible. Detour are for long be-points.
Set the saerch halo to one GCell in the initial routing stage (before
ripup).
* Bug: In KatanaEngine & NegociateWindow, call _computeCagedconstraints()
inside NegociateWindow::run(), as segments are inserted into tracks
only at that point so we cannot make the computation earlier.
* Change: In Katana::Manipulator::repackPerpandiculars(), add a flag to
select whether to replace the perpandiculars *after* or *before* the
current segment.
* Change: In Katana::NegociateWindow::NegociateOverlapCost(), when the
segment is fully enclosed inside a global, the longest overlap cost
is set to the shortest global hoverhang (before or after).
When the cost is for a global, set an infinite cost if the overlapping
segment has a RP distance less or equal to 1 (this is an access segment).
* Bug: In Katana::PowerRailsPlane::Rail::doLayout(), correct computation of
the segments extension cap.
* New: In Katana::QueryPowerRails::addToPowerRail(), add support for Pad.
* Change: In Katana/PreProcess::protectCagedTerminals(), apply the contraints
to any turn connected to the first segment of the RoutingPad so the
perpandicular constraints got propagated to the perpandicular segment...
* Change: In RoutingEvent, cache the "distance to RP" value.
* Change: In RoutingEvent::Key::compare(), sort *first* on distance to
RoutingPad, then layer depth. If both distance to RoutingPad is null,
then sort on segment length.
* Change: In RoutingEvent::_processRepair(), try a repack perpandicular with
perpandiculars first (then with perpandicular last, then give up).
* Change: In SegmentFsm::bindToTrack() and moveToTrack(), set an axis hint
when creating the insertion event.
* Change: In SegmentFsm::_slackenStrap(), add a step through slacken between
minimize and maximum slack (wihch directly end up in unimplemented).
* Change: In Session::_addInsertEvent(), add an axis parameter needed when
the axis of the segment is not the one of the track (case of wide
segments or non-preferred direction).
* Bug: In Track::_preDestroy(), bad management of the TrackElement reference
count. Destroy the segment only when reaching zero...
* Bug: In Track::expandFreeIneterval(), forgotten to manage case when there
is a set of overlaping segments at the "end" of the track, the
EndIsTrackMax was not set.
* Change: In TrackCost::Compare, increase the cost when an overlaping
segment is at it's ripup limit. We should try *not* to rip it up if
we can. Add a dedicated flag "AtRipupLimit".
* Change: In TrackElement, add proxies for isUnbreakable(), new function
updateTrackSpan().
* New: In TrackFixedSegment CTOR, when a supply wire of METAL2 or above is
found, make the underlying GCells "GoStraight".
* New: In TrackElement::canDogleg(GCell*), check for already done perpandicular
dogleg on source/target (reject if so).
The short net mode degrade the routing in some cases. This will be
fixed in a next batch of commits.
* New: In Hurricane::NetRoutingProperty, added "ShortNet" flag for Nets
that are completly inside *one* GCell.
* Bug: In CRL::BlifParser::Model::staticInit(), when looking for the
output of zero and one cell, also skip the blockage net (as well as
automatic and supplies).
* New: In Anabatic::AutoSegment, added "ShortNet" flag to know if the
segment is part of a short net (fully included in *one* GCell).
Also add accessor/mutators for the _analogMode flag (was it ever
used before?).
* New: In Anabatic::NetBuilder::singleGCell(), if a RoutingPad is
vertically small, add a vertical segment to give it some slack.
* New: In Anabatic::Dijkstra::_materialize(), detect "short net" as
they have only one GCell in their source list...
* Bug: In AnabaticEngine::_loadGrbyNet(), reset the AutoSegment
"short net" and "analog mode" creation flags between two different
nets.
* New: In Katana::Configuration, added dedicated ripup for short net
segmnts.
* New: In Katana: partially implemented support for "short dogleg", that
is dogleg that are always kept in same metal because they connect
neighboring perpandicular tracks. Not finished neither activated
yet.
* New: In Katana::TreckElement and derived, export the the *short net*
support from AutoSegment.
* Bug: In Katana::RoutingEvent::_processRepair(), when a segment is
successfully inserted, re-process any perpandicular that is in
repair state, as it may have a new chance to be placed.
* New: In Katana::SegmentFsm::slackenTopology(), always reject short nets.
* Bug: In Katana::Track::check(), correctly handle wide segments instead
of issuing false check messages.
* New: In Hurricane::Entity, add an id counter limit and a memory size
limit. The two limits are checked only when a new Entity object is
created. This should help avoiding massive memory links.
* New: In CRL Core, add a "crlcore.groundName" and a "crlcore.powerName"
parameter to specify the name of the ground/power signals to be
created if they are missing in a Cell. For Alliance libraries it
would be "vss" & "vdd" (default values), but for real technologies,
it is often "gnd!" & "vdd!".
The Blif parser is modificated to make use of it.
* Bug: In AnabaticEngine::unify(), set the resulting unified segment in
the center of the GCells common side. Gcells under a segment are
found by using the edge that cover the segment axis. When we have
a "bend" GCell stack and the axis is wrong, they could be ommited.
This was causing deleted segments to be not removed from some
Edges, then core dump.
* Change: In Anabatic::AutoSegment::create(), smarter choosing of the
reference contact, select the fixed or terminal one instead of
always the source one.
* New: In Anabatic::Edge::isEnding(), new function to check if a
segment going through an Edge is starting/ending in either source
or target GCell of the edge (active only when running in channel
mode).
* New: In Anabatic::Edge::add(), a segment takes part in the occupancy
only if it is not ending in either source or target (channel mode
only). The occupancy due to terminal is pre-computed in Katana.
* New: In Anabatic::Edge::ripup(), in channel mode, never ripup a
segment which is ending in either source or target (we *have* to
access this edge to connect to the terminal).
* Bug: In Anabatic::GCell::hcut() and vcut(), force the update of
the Edge which is on the side that will get splitted by the cut.
It's capacity will be reduced to it must be updated.
* Change: In Anabatic::GCell::updateGContacts() add a flag to conditionnally
update horizontals or verticals only. We may require only a partial
update when resizing the GCell in only one direction.
This, again, related to the fact that we compute the GCells under
a segment thanks to it's axis position, so we need to be very careful
when modificating axis.
* Change: In Katana::Block::resizeChannels(), only update GContact vertical
position. Do not disturb X positions of segments.
* Bug: In Katana::GlobalRoute::DigitalDistance, in channel mode, some
Edges can have a zero capacity, but still be reachable if the net has
a terminal in either source or target. Look for this case and return
a distance of zero instead of "unreachable". This was causing the
global routing not to complete in channel mode.
For computing the edge distance, makes the vertical edges much more
long (10 times) than the horizontal ones as the vertical capacity is
very limited. Hard coded for now, should make it a parameter in the
future.
* Change: In KatanaEngine::annotateGlobalGraph(), decrease the capacity
of edges with reserveCapacity for each terminal inside a GCell.
Both north and south edges are decreased as we a terminal will
block both north and south edges.
As a counterpart, the Edge capacity is not decreased when the
global router connect to a terminal.
* Change: In Katana::RoutingEvent::revalidate(), when in repair stage,
do not expand the slack for horizontal segments in channel mode.
So they may not overlap the standard cell row.
* Bug: In Stratus documentation, do not use the french option in babel,
the documentation is in english!
* New: In Documentation, added Hurricane/Python tutorial, part for drawing
layout.
* New: In Commons, inspector support for std::pair<T,U>.
* New: In Hurricane::Layer, ContactLayer & ViaLayer, support for non
square VIAs. The hole (cut) remains square, but the various metal
extensions can now be different in X and Y. The ::getEnclosure()
method now takes a flag EnclosureH / EnclosureV.
* New: In Hurricane::DbU, inspector support for:
std::pair<DbU::Unit,DbU::Unit>
std::array<DbU::Unit,3>
Must be defined here as DbU do not exists yet in Commons.h
* Bug: In Hurricane::Interval::getSize(), when the interval is "full span",
do not return the difference between min and max, but directly DbU::Max.
(the previous result was -1 !)
* New: In CRL Core Python/Technology.py, support for non square VIAs in
the configuration files. Applied to FreePDK 45.
* New: In CRL::RoutingGauge, added a "symbolic" flag to tell if a gauge
is for symbolic layout or not. Exported to Python.
* New: In Anabatic::AutoHorizontal::updatePosition(), differentiated
computation for soure or target taking account of the VIA extension
in the right segment metal (due to non-square VIAs).
* Change: In Anabatic::AutoHorizontal::_makeDogleg(), the dogleg is
UP for HV gauges and DOWN for VH.
* New: In Anabatic::AutoSegment::_initialize(), create a cache of the
various extension length for each layer (viaToTop, viaToBottom,
viaToSame).
New implementation of getExtensionCap() using the previous cached
extension table. See updatePositions().
New static functions to access the extension cache in the header:
getViaTotopCap() ...
* Change: In Anabatic::AutoSegment, in various update methods, updateOrient()
must always be called *before* updatePositions() as extensions are
dependant on source/target.
* New: In Anabatic::AutoSegment::getEndAxes() compute the position of the
first source and last target position (center/axes) on an *aligned*
set of segments.
* New: In Anabatic::AutoSegment, add a new state flag SegAxisFixed to
signal segments that can be put on only one track. Specific case
to VH gauge for a M1 vertical terminal with a M2 vertical segment.
The M2 is effectively bound to the M1 axis position.
* Bug: In Anabatic::NetBuilderVH::_do_xG_xM1_xM3(), in case of E/W global
and only one RoutingPad the connexion to the RoutingPad was duplicated.
It was valid, but totally stupid.
* Bug: In Anabatic::Session::_canonize(), for an aligned segment set,
intersect the user constraints from all segments instead of only
considering the canonical one.
Issue a warning about too tight constraints only for symbolic
gauges. It may be correct for the real ones.
* New: In Katata::DataNegociate::update(), more accurate computation
of the perpandicular free interval. Use segment extension cap
calculation. Create a special case for fixed axis segments allowing
them to find alternative free interval, try under source and under
target as they are likely to be draggable segments.
* Change: In Katana::Manipulator::relax(), use the extension cap value
to compute the axis of the perpandicular segemnts.
* Change: In Katana::Manipulator::moveUp(), now move up the whole set
of aligned segments instead of just the canonical one.
* Change: In Katana::NegociateWindow::loadRoutingPads(), more accurate
TrackMarkers insertions for fixed terminals.
* New: In Katana::RoutingEvent::Key::Compare::operator(), segments with
fixed axis are processed prior to any others.
* New: In Katana::RoutingEventLoop, store segment pointers instead of
ids to generate more accurate error messages.
* Change: In Katana::RoutingPlane::create(), perform local track
assignment only for HV gauges.
* Change: In Katana::SegmentFsm::_slackenLocal(), add a "dragMinimize"
step in the automaton. Mutliple states transitions can occurs in
a row if an action fails.
* New: In Katana::Session::_toIntervalAxis(), normalize interval
bounds so they are on track positions (by shrinking the interval).
* Bug: In Katana::TrackMarker CTOR, the weigh computation was wrong.
* Bug: In Katana::PreProcess::protectCagedTerminals(), the contacts of
the fixed segment must be fixed too.
* Change: In Katana::RoutingPlane constructor, more accurate computation
of the extensionCap (for real technologies).
* Bug: In Katana::DataNegociate::update(), the perpandicular free
interval must be shrunk of the extensionCap of the perpandicular
layer. This problem did show with metal1 "half-offgrid" terminals.
* Change: In Katana::runGlobalRouter(), increase the number of ripup
passes to ten. Display the overloaded edges and the related nets.
* New: In Anabatic::AutoContact and the derived classes, manages wide
wires. The contact self dimension itself according to the segments
it is connected to. Special case for the AutoContactTerminal which
also read the size of the component it is anchored upon.
New refresh method "updateSize()" and flag CntInvalidatedWidth.
to compute the size.
In AutoContactTerminal, compute the constraint box according to
the width of the segment.
* New: In Anabatic::AutoSegment, flags are now implemented as "static const"
attributes of the class. The flags are stored into a uint64_t as
they are more than 32.
Added new flag "SegWide" and associated predicates.
* Change: In GCellTopology::_doHChannel() and GCellTopology::_doVChannel(),
uses the simpler overload of AutoSegment::create() in order to detect
the wire width automatically.
* New: In Katana::Manipulator, split insertToTrack() and forceToTrack()
into a one-track method and a segment level method that iterate over
the track span of the segment.
* New: In Katana::SegmentFsm, for each cost in the table, now allow access
to a specific track. So the base functions have now two parameters:
"icost" and "itrack" (has a cost can have multiple tracks in the case
of wide segments).
* Change: In Katana::TrackElement, remove the index of the element inside
it's track, as for a wide segment it will not be meaningful for the
non-base track. This means that we have to use the Track::find()
method each time instead.
Remove the wide flag, as it is a duplicate of the one in AutoSegment.
Added a getTrackCount() method to tell the number of track the
segment is inserted into. Needed in the Track destroy step to delete
a segment only when the last track that refers it is destroyed.
Added getSymmetricAxis() to correct the computation of the symmetric
base track in case of wide segment as the base track is not centered
but the the leftmost one.
* Change: In Track::insert() insert wide segments in their whole track span.
* Change: In TrackCost, create an array of costs according to the segment
track span.
* Change: In TrackSegment::create(), now activate the factory and create
wide segments.
* Bug: In Katana::AutoSegments_Perpandicular, correct the debug indentation
problem (ever shifting to the right).
* New: In Katana::SegmentFsm, the object is now able to handle two events
at the same time. The master and it's symmetric. When there is no
symmetric, the corresponing data is just left blank. This makes a
bigger object, but as there is only one when running, it is not an
issue.
Candidates tracks are now an vector of array<2> (pairs), the
TrackCost::Compare() functor has to be wrapped through CompareCostArray.
The compined TrackCost of the two tracks is accumulated into the first
element.
Everything related to events gets duplicated: _event is now _event1
and _event2, and so on.
As there can be now two Manipulator actions done with SegmentFsm,
this class now completly hide the Manipulator level from the
RoutingEvent processing.
New function ::bindToTrack() to perform the track insertion.
* New: In Katana::TrackCost, add a new ::merge() function.
* New: In Katana::TrackElement and Katana::TrackSegment, add symmetric
management. Allows to know if a TrackElement has a symmetric and to
access it.
* New: In Katana::DataSymmetric, add new overload for ::getSymmetrical()
to handle DbU::Unit and intervals.
* Change: In Katana::RoutingEvent, remove all direct uses of Manipulator
objects. Now any change to the event associated segment must go through
call to Segment Fsm.
* Change: In Katana, adjust the debug level so internal informations are
put below level 156.
* New: In Hurricane::DbU, in ::getValueString(), special display when the
value is Min or Max (more helpful than a gigantic number).
* Bug: In Hurricane, in StaticObservable::getObserver(), if the slot
pointer is NULL, do not try to access the owner. Returns NULL, so
the caller can be aware of the situation...
* Change: In Hurricane, in BreakpointWidget & ExceptionWidget some
cosmetic changes (fonts and window sizes).
* Bug: In Anabatic, In AutoHorizontal::getConstraints(), take into account
the constraints from the source AutoContact, as it holds the constraints
transmitted by the RoutingPads and sets up by propageConstraintsFromRp().
It is likely to be a bug affecting the original Katabatic as well.
* Change: In Anabatic, in RawGCellsUnder(), check that the segment is not
completly oustside the cell abutment box and truncate the coordinates
to the part that is inside. Use the "shrink" if we reach the east/north
border.
* Change: In Anabatic, in Configuration, no more decorator because we will
use a true derived relationship. Katana *derives* from *Anabatic* and do
not *decorate* it, so the Configuration can do the same. It also implies
that we directly create a Katana engine, not an Anabatic one.
* Change: In Anabatic, in Session, do not allow the opening of the Session
in a standalone fashion (with a static method). Instead it must be opened
using the relevant method of the Anabatic/Katana engine. This ensure we
are opening the right Session type.
* Change: In Anabatic, in AutoSegment_Aligneds() collection the seed segment
is not part of the collection by default, but will be included if the
Flags::WithSelf is set.
* Change: In Configuration, all the flags value are now defined in two steps.
Declared in the header and initialized in the module. This is to prevent
the fact that on some cases, in relation with the Python "extern C" part
modules, we need a true allocated variable. It was causing weird linking
problems.
A side effect is that they can no longer be used as entry is switches,
have to replace them by if/else.
* New: In Anabatic, new GCell::getNeighborAt() utility function.
* Bug: In Anabatic, in GCell::doGrid(), tag all the GCells of the grid with
the grid type... Back annote all the edges capacity (north & east) with
the reserved local capacity.
* New: Complete portage of Kite over Anabatic. The new engine is christened
"Katana" for Kite-Analogic. When it's capabilities and performances
will be on a part with Kite, it is to completly replace it (and take
back the "Kite" name). Preliminary tests seems to show that, contrary
to intuition (because built on a more complex/slower grid), it is even
slightly faster than Kite 8-).
Jean-Paul Chaput