* New: In Hurricane::Layer, add support for a minimal area (given in
microns). Exported in the Python interface.
* New: In Anabatic::AutoSegment::bloatStackedStrap(), method to
enlarge too small vertically stacked VIAs. For now just create
a square ensuring the minimal area. Potentially cause DRC error in
some cases so needs to be refined.
* New: In Anabatic::_gutAnabatic(), check for too little stacked VIAs
and display a report.
* New: In Hurricane::NetRoutingProperty, add and change the meaning
of the following flags:
- ManualGlobalRoute : now means that a global routing *trunk*
is present, made of "gmetalh", "gmetalv" & "gcontact".
- Manualdetailroute : added, get the former meaning of
ManualGlobalRoute, that is, the detailed routing is
already present for this net, but can be changed by the
detailed router. Implies that it respect the Terminal,
HTee & VTee structuration.
* New: Add Anabatic::Diskstra::loadFixedGlobal(), to account
a manually global net into the edges capacities.
* New: In Anabatic::Edges::ripup(), exclude manually global routed
segments from the ripup. Change the segment sorting function
so that thoses segments are put in head of list (considered
as "smaller").
* Change: In AnabaticEngine::setupPreRouteds(), now detect manual
global routed and manual detail routed signals, and tag them
accordingly.
* New: In AnabaticEngine::Configuration & Session, add proxies
for the global routing layers ("gmetalh", "gmetalv", "gcontact").
* New: In Anabatic::Constants, add flags for global fixed and
detail routed nets.
* Change: In KatanaEngine::updateEstimateDensity(), now use int64_t
for flute coordinates.
* New: Add CRL::RoutingGauge::hasLayer(), to know if a layer is
managed by the gauge (comparison by mask).
* In NetBuilder::_do_xG_1PinM3(), in the three global case, an
incorrect connexion was made.
* In NetBuilder::_do_2G_xM1_1PinM2(), in the global E+W case,
segment between vtee1 <-> turn1 must be vertical.
* Bug: In Anabatic::AutoHorizontal::_slacken(), when creating the target
dogleg, if the target was a fixed pin (M2) on the east side, the
vertical was put righ on the side, which is *not* an allowed track.
The exact east side is not covered by a vertical track (this comes
from a policy adpopted for the GCell, to avoid overlapping tracks
on the border). So we got an error message when katana tries to
bind it to a track. Now shift one perpandicular pitch to the *left*
for the EAST pins.
* Change: In Anabatic::NetBuilderHV::_do_1G_xM1_1PinM2(), the M2 pin
(horizonal) was directly aligned with the outgoing global through
a H-Tee. This was too rigid. Now it can be misaligned.
* Change: In AnabaticEngine::_desaturate(), now use a STL priority
queue built upon a vector with duplicates of the GCell keys.
Much much more faster than the previous set with a custom
sorting key over the GCell. Insertion & removal where getting
a lot of time. Now it's down to less than a minutes, even for
big designs.
* Change; In Anabatic::GCells, add the ability to clone the GCell
key, to use it independently in GCells sorting containers.
This way the cloned value do not change when the GCell is
updated. Keep track of the latest (most up to date) cloned
key.
* Bug: In Anabatic::NetBuilderHV::_do_2G_xM1_1PinM2(), in the case of a
bend of global wires, the topology was faulty. Too rigid topology,
the global wire was forcibly aligned on the external Pin.
* New: In Anabatic::AutoContactTerminal, new method "isOnPin()" to
know if the terminal contact is on a Pin. Introduced in base
class.
* Bug: In Anabatic::AutoHorizontal::_canSlacken() & AutoVertical,
forbid slackening from a Pin. As Pin are all on the side of the
cell (aligneds) and the perpandicular segment will be locked on
the Pin, it generates intractable overlaps for the router.
* Bug: In Anabatic::Configuration::selectRpComponent(), always select
the Pin as the best component. It is mandatory for a block that
we pick up the terminal at the periphery and not one deep inside
the block.
* Bug: In Hurricane::RoutingPad::setOnBestcomponent(), same rule as
in Anabatic, if there is any, the Pin must always be the best
RoutingPad component.
* Bug: In Hurricane/Commons.h, modify the getRecord<>() templates so
that for both vector<Element> and vector<Element*>, the individual
record created for each element are donne with pointers. That is,
for the vector<Element> case, we take a pointer.
As a general policy, except for the POD types, always use pointers
or references to data in the records/inspector. Never uses values
that can call the copy constructor.
Suppress INSPECTOR_PV_SUPPORT() macro, keep only
INSPECTOR_PR_SUPPORT().
Provide value support only for getString<>() template.
This value & copy constructor problem was causing a crash when
trying to inspect Hurricane::AnalogCellExtension.
* New: In Hurricane::Technology, change the API of the PhysicalRule,
now we can only create/get PhysicalRule, but setting the value of
the rule itself must be done on the rule.
Enhance PhysicalRule to provide for stepped rules, non isotropic
and ratio rules.
Merge TwoLayersPhysicalrule in PhysicalRule, much simpler to
suppress the management of derived classes. That means that we
loose a little memory as some fields are mutually exclusive.
Not a problem considering that there will not be so many of thoses
objects.
* New: In CRL/helpers.analogtechno.py, enhanced DTR support for rules
like:
('minSpacing' , 'metal1', ((0.4,20.0), (0.8,1000.0)), Length, 'REF.1')
('minEnclosure', 'metal1', 'cut1', (0.2,0.3) , Length, 'REF.2')
('minDensity' , 'metal1', 0.30 , Unit , 'REF.3')
The DTR parser has been updated, but not the oroshi.dtr Rule
cache for analog components. Given a rule name, the value used
will be the horizontal one of the first step.
* Change: In hurricane/doc/hurricane, re-generate the documentation
with updated support for Technology & PhysicalRule.
* New: In Anabatic::NetBuilder, some GCells configurations of Libre-SOC
"test_issuer" (soclayout/experiments9) did have more METAL1 terminals
than was though possible. Just added more entries in the connexity
table for bigger numbers of METAL1. No new configuration was added,
used the already existing ones.
* Bug: In Anabatic::AutoHorizontal & AutoVertical, in getGCells()
method, do not display the "NULL GCell under" error message if the
segment has just been created. It could on a "wrong" axis position
so the line probing method may fail.
* Bug: In AnabaticEngine CTOR, if the "blockagenet" is created there,
do not forget to set it's type to BLOCKAGE (to avoid later warnings).
* Bug: In Anabatic::NetBuilder::_load(), do not display a warning if the
blockage net has no RoutingPads (it *must* not have one).
* Bug: In Bora::SlicingNode::clearGlobalRouting(), as we are unrouting the
cell, the flags set up by Katana must be reset. The Cell is no longer
"Terminal" and it's nets are "Un-flattened".
* Bug: In Anabatic::Session::_revalidateTopology(), when iterating over
_segmentInvalidateds, the vector can be modified. If it leads to a
reallocation we end up on invalid iterators (using freed memory so
sometimes with overwritten contents). Now, iterate with an index
which warranty that we get a valid item at each iteration of the
loop. And, of course, the vector is ensured to not shrink...
* Change: In Anabatic::Session::Session(), reserve (pre-allocate) at least
1024 elements for all vectors. Mostly prevent the above bug and
avoid constant reallocation.
* Change: In CRL::LefParser::_macroCbk(), create a Catalog entry for the
newly read MACRO (that is Cell) and sets the Logical, Physical,
InMemory and TerminalNetlist flags.
* Bug: In CRL::LefParser::_siteCbk(), check for NULL cell gauge.
* New: In CRL::AllianceFramework, add setCellGauge(), to set the default
cell gauge. Exported to Python.
* Change: In CRL/etc/common/technology.py, create variables for VIA
layers, so we can modify their properties afterwards.
* New: In CRL/etc/node45/freepdk45, port the configuration files to the
new Python "importable" format.
Note: in kite.py, all the gauges (Routing & Cells) must be named
"LEF.CoreSite" to please my LEF parser, so it can match the gauge
name with the SITE name for standard cells.
* Bug: In Anabatic::NetBuilderVH::_do_2G(), forgotten to be reimplemented
from the base class. Simply redirect to _do_xG().
* Change: In Katana::PowerRailsPlanes::PowerRailsplanes(), create plane
from the layers in the RoutingGauge and their associated blockages
instead of sweeping through all the basic layers.
Allow to distinguish bewteen "METAL" (symbolic) and "metal" (real).
* Bug: In Katana::NegociateWindow::createTrackSegment(), *fixed* AutoSegment
in conflict with blockage where removeds. This was creating "holes"
in the Anabatic articulated segment structure. Now just *don't*
create the TrackSegment. Pass the regression tests, but not sure
it is not generating problems elsewhere.
* New: AnabaticEngine::checkPlacement() to issue more clear errors about
a defective placement.
* New: In Anabatic::NetBuilderHV(), added configurations to manage
one Pin M3 + one M1 terminal plus 2 & 3 globals:
* _do_2G_1M1_1PinM3()
* _do_3G_1M1_1PinM3()
They were occuring for the first time in soclayout/experiment7
in the "flat" approach.
* New: In Katana::runNegociate(), mark the newly routed netlist as
"NetlistTerminal" so it is not placed and routed *again* when
reused as an instance (mostly interract with Etesian).
* Bug: In Katana::AutoSegment::_preDestroy(), remove the segment from
the source & target AutoContact cache.
In LibreSOC/experiment7, weird placement caused fixed AutoSegment
overlaping blockage to be deleteds. It seems to have never occured
before (or at least, no ended up in core dump).
* Bug: In Hurricane::NetRoutingState::getSymValue(), outrageously bad
computation of the symmetric coordinate when the value was superior
to the axis... (shame on me).
* Change: In Anabatic::Disjkstra::load(), for symmetrically paired nets,
check that the axis of symmetry is *outside* the searchArea.
Otherwise, the two mirrored areas overlaps and the two nets will
unescapably be on top of each other. Issue a warning but still
continue.
* Change: In Anabatic::Vertex::isRestricted(), allow perpandicular
wire to go through struts or thin (less than one routing pitch)
node. May have to recheck in the future and restrict to struts
only.
* Bug: In Bora::HVSlicingNode::updateSymNetAxis(), rescursive call in
child node was not systematically done (bad curly brace position).
Also checks that symmetries are not empty before accessing the
front element (one less core dump).
* Change: In all tools, FindTOOL.cmake, no longer use LIB_SUFFIX to
search for tool libraries but try "lib64/" then "lib/".
* Change: In bootstrap/socInstaller.py, take Debian 10 into account.
* Change: In bootstrap/docker, move from Debian 9 to Debian 10.
* New: In Hurricane::Cell::isLeaf(), a leaf cell was defined as one
without instances. Now it can be software defined with the
"FlattenLeaf" state. If it is flagged "flatten leaf" is will be
considered as a leaf by the trans-hierarchical walkthrough.
This flag is also set for Cells in the Alliance CATAL.
* New: In Hurricane::Cell_LeafInstanceOccurrences::progress(), add a
test to prune leaf cells.
* Bug: In Hurricane::getComponentOccurrences(), when calling the
locator constructor, the "withLeafCells" argument was forgotten
and was getting the value of "doExtraction" (wich, fortunately,
was the same).
* Change: In Hurricane::HypreNet_LeafPlugOccurrences::progress(),
prune the leaf cells instead of the terminal ones.
* Change: In Hurricane::HypreNet_ComponentOccurrences::progress(),
prune the leaf cells instead of the terminal ones.
* New: In Hurricane::Cell, add a "useFlattenLeaf" mode to take into
account or ignore the "FlattenLeaf" flag when doing trans-
hierarchical walkthrough.
Not sure if it shouldn't be systematic.
* New: In Etesian::toColoquinte() and other, activate the "FlattenLeaf"
mode for all walkthough. So we can stop at already placed sub-blocks.
* Bug: In Etesian::toColoquinte(), when placed sub-block where present,
the number of instances was under estimated, so the instance array
was oversized and the end went unitialized. So we were getting all
kind of strange behavior from Coloquinte...
Now throw an exception if the number of instances differs from
the computed size.
* Bug: In Etesian::toColoquinte(), as for the instance array, now
correctly compute the size with the ecluded nets (supplies, clocks).
* Bug: In Etesian::resetPlacement(), event if the Cell is unplaced,
go through the instance list to remove the potential feed cells.
The netlist is written back after placement *with* the feed
cells added. So, when loading again, they where cluttering the
netlist and giving feed redefintions warning. They also generated
erratic behaviors.
* New: In Anabatic::NetBuilderHV, added configurations for:
* 1G_1M1_1PinM3
* 1G_xM1_1PinM2
* 2G_xM1_1PinM2
* doRp_AccessNorthPin
* New: In Anabatic::NetBuilderHV, added Pin management in SingleGCell.
* Bug: In Anabatic::NetBuilderHV::_do_xG_1PinM3(), the North/South
global routing configuration was forgotten (only East/West).
* Bug: In Katana::TrackFixedSegment, the blockage net was a static
variable initialized at the first run. So we were getting stuck
with the blockage net of the first cell to be routed. Of course,
it did show only when Katana was run multiple times in the same
process.
* Change: In Hurricane::Viewer::ExceptionWidget & CRL/python/helpers/io.py,
downscale icons for non-HiDPI screen.
* Change: In CRL/etc/common/display.py, change the display threshold of
METAL1 layer so it do not appear at high scaling.
* New: In Etesian, activate the "setFixedAbHeight()" feature and export it
to Python. Allows to increase the space margin at constant height.
To be used by the P&R conductor.
* Change: In Unicorn/cgt.py, when running a script, insert the current
working directory at head of the sys.path, not at the end. So installed
modules do not shadow local one.
* New: In Anabatic::Edge, new accessor "getRawcapacity()" to know the full
capacity of the edge, that is, the real maximum number of tracks that
can go through the associated side.
* Change: In Katana/BloatProfile/Slice::tagsOverloaded(), bloating policy
change, now bloat all the instances under the GCell, not only the first
one.
* Change: In KatanaEngine::runGlobalRouter(), restore the search halo growth
policy to expanding of 3 GCells every 3 iterations.
New metrics displayed, the edge wire length length overload.
* Change: In cumulus/plugins/ConductorPlugin.py, now accepts the following
configuration parameters:
- "anabatic.globalIterationsEstimate", maximum number of global
iterations during the bloating computation passes.
- "conductor.useFixedAbHeight", tells wether the additionnal blank
space must be added so the aspect ratio is kept or the height is
kept (and the block become wider).
Disable the display of "rubber" to unclutter a little the view.
This commit contains two set of features that should have been commited
separately.
1. Compliance with clang 5.0.1, tested with the RedHat collection
llvm-toolset-7. This allow Coriolis to be compiled under Darwin (MacOS)
with Xcode & macports. The bootstrap install system has been modificated
accordingly.
2. The basic support for routing density driven placement. Related
features are:
* Bloat property. Each Occurrence of an Instance can be individually
bloated. This property not attached to any tool to allow the placer and
router to share it as wanted. Nevertheless, it is defined in Etesian.
* BloatProfile in Katana, add individual Bloat properties to Instances
occurrences based on the East & North overflowed edges of each GCell.
* Support in ToolEngine for a "pass number" of a tool. This pass number
is mainly used to make "per pass" measurements. The MeasureSet system
is improved accordingly to support multiple values of a same measure.
* Embryo of "P&R Conductor" to perform the place & route loop until the
design is successfully placed. May be the first brick of a Silicon
Compiler.
* Change: In boostrap/FindBoostrap.cmake, in setup_boost(), added tag to
the python component for macport (ex: python27).
* Change: In boostrap/build.conf, put etesian before anabatic for
instance occurrence BloatProperty dependency.
Added option support for the "llvm-toolset-7" collection to build
against clang 5.0.1.
* Bug: In Hurricane::getRecord( const pair<T,U>& ), the getSlot<> templates
for first & second arguments must be called with <const T> and <const U>
as the pair itself is const (and not simply <T> & <U>).
* Change: In Hurricane::getSlot() temlate, only use "string" arguments and
not const string&, simpler for template argument deduction.
* Bug: In Hurricane::AnalogCellExtension, the StandardPrivateProperty<>
template has a static member "_name". Clang did show that the template
for this static number has to be put inside the namespace where the
template *is defined* (i.e. Hurricane) instead of the namespace where
it is instanciated (i.e. Analog).
* Bug: In Isobar, Matrix_FromListOfList(), PyInt_AsPlacementStatus() must
be put outside the C linkage back in the Isobar C++ namespace (clang).
* Bug: In Hurricane::DBo::~DBo, and derived add a throw() specification
(clang).
* Bug: In Hurricane::RegularLayer::getEnclosure() & setEnclosure(), change
signature so it matches the one of the base class (clang).
* Bug: In Hurricane::CellPrinter, use double brackets for initializer list
(clang).
* Change: In Hurricane::Breakpoint, reverse the meaning of the error level.
Only error level *lesser or equal* than the stop level will be enabled.
* Bug: In CRL/python/helpers/__init__.loadUserSettings(), must put the
current working directory in the sys.path as in certain configuration
it may not be included.
* Bug: In CRL::ApDriver, DumpSegments(), no longer generate segments when
encountering a RoutingPad on a top-level Pin Occurrence. The segment
was generated in the wrong direction, creating DRC violations on the
"mips_core_flat" example.
* Change: In CRL::Measures, partial re-design of the measurements management.
Now, each kind of measure can accept multiple values put in a vector.
The index is intented to match a tool run number.
* Change: In CRL::Histogram, add support for multiple sets of datas,
indexeds with tool run number.
* Change: In CRL::ToolEngine, add support for multiple pass number, add
addMeasure<> templates for the various data-types.
* Change: In CRL::gdsDriver & CRL::gdsParser(), comment out unused GDS record
name constants.
* New: Etesian::BloatProperty, property to attach to Instance occurrences
that contains the extra number of pitch to add to the cell width.
* Bug: In AutoSegment::CompareByDepthLength, the segment length comparison
was wrong, it was always returning true, which broke the "strick weak
ordering" of the comparison.
This was producing a core-dump in GCell::updateDensity() when sorting
a vector<>. The end() iterator was being dereferenced, leading to the
problem.
* Bug: In Katana::DataSymmetric::checkPairing(), the test for segments
whose axis is perpandicular to the symmetry axis was wrong
("!=" instead of "-").
* New: In Katana/GlobalRoute, new ::selectSegments(), selectOverloadedgcells()
and selectBloatedInstances() to automatically select segments from
overloaded edges, overloaded GCells and bloated cells.
* Change: In KatanaEngine, return a more detailed success state, distinguish
between global and detailed.
Add support for multiple routing iterations.
* New: In cumulus/python/plugins/ConductorPlugin.py, embryo of routing
driven placement.
* New: In bootstrap/coriolisEnv.py, add the "etc" directory to the
PYTHONPATH as initialization are now Python modules.
* New: In Hurricane/analogic, first groundwork for the integration of
PIP/MIM/MOM multi-capacitors. Add C++ and Python interface for the
allocation matrix and the list of capacities values.
* Change: In Hurricane::RegularLayer, add a layer parameter to the
constructor so the association between the RegularLayer and it's
BasicLayer can readily be done.
* Change: In Hurricane::Layer, add a new getCut() accessor to get the
cut layer in ViaLayer.
* Change: In Hurricane::DataBase::get(), the Python wrapper should no
longer consider an error if the data-base has not been created yet.
Just return None.
* Bug: In Isobar::PyLayer::getEnclosure() wrapper, if the overall
enclosure is requested, pass the right parameter to the C++ function.
* Change: In AllianceFramework, make public _bindLibraries() and export
it to the Python interface.
* Change: In AllianceFramework::create(), do not longer call bindLibraries().
This now must be done explicitely and afterwards.
* Change: In AllianceFramework::createLibrary() and
Environement::addSYSTEM_LIBRARY(), minor bug corrections that I don't
recall.
* Change: In SearchPath::prepend(), set the selected index to zero and
return it.
* Change: In CRL::System CTOR, add "etc" to the PYTHONPATH as the
configuration files are now organized as Python modules.
* New: In PyCRL, export the CRL::System singleton, it's creation is no
longer triggered by the one of AllianceFramework.
* New: In CRL/etc/, convert most of the configuration files into the
Python module format. For now, keep the old ".conf", but that are no
longer used.
For the real technologies, we cannot keep the directory name as
"180" or "45" as it not allowed by Python syntax, so we create "node180"
or "node45" instead.
Most of the helpers and coriolisInit.py are no longer used now.
To be removed in future commits after being sure that everything
works...
* Bug: In AutoSegment::makeDogleg(AutoContact*), the layer of the contacts
where badly computed when one end of the original segment was attached
to a non-preferred direction segment (mostly on terminal contacts).
Now use the new AutoContact::updateLayer() method.
* Bug: In Dijkstra::load(), limit symetric search area only if the net
is a symmetric one !
* Change: In Katana/python/katanaInit.py, comply with the new initialisation
scheme.
* Change: In Unicorn/cgt.py, comply to the new inititalization scheme.
* Change: In cumulus various Python scripts remove the call to
helpers.staticInitialization() as they are not needed now (we run in
only *one* interpreter, so we correctly share all init).
In plugins/__init__.py, read the new NDA directory variable.
* Bug: In cumulus/plugins/Chip.doCoronafloorplan(), self.railsNb was not
correctly managed when there was no clock.
* Change: In cumulus/plugins/Configuration.coronaContactArray(), compute
the viaPitch from the technology instead of the hard-coded 4.0 lambdas.
In Configuration.loadConfiguration(), read the "ioring.py" from
the new user's settings module.
* Bug: In stratus.dpgen_ADSB2F, gives coordinates translated into DbU to
the XY functions.
In st_model.Save(), use the VstUseConcat flag to get correct VST files.
In st_net.hur_net(), when a net is POWER/GROUND or CLOCK also make it
global.
* Change: In Oroshi/python/WIP_Transistor.py, encapsulate the generator
inside a try/except block to get prettier error (and stop at the first).
* Change: In Anabatic::AutoContactTerminal::updateGeometry(), when a
draggable AutoContact is moved, pitch it on the routing grid instead
of putting it in lowest/highest position.
* Change: In Anabatic::GCell::updateDensity(), all non-passthrough wires
now have a cost of 0.5 instead of 0.33 for locals.
* Change: In Manipulator::canMoveUp(), increase the "reserve" amount to
1.0 for "far from terminal" wires (rpDistance > 2).
* Change: In NegociateWindow::NegociateOverlapCost(), always sets "AtRipupLimit"
when the overlapping segment is nearing it's maximum ripup limit.
(different detection for non-preferred and regular)
* Change: In SegmentFsm::_slackenStrap(), call avoidBlockage() if it is
overlapping a blockage *or* a segment at it's ripup limit. I hope I
didn't create an infinite loop here.
* Bug: In cumulus/plugins/PadsCorona.py, CoreWire._computeCoreLayers(),
the big contact between symbolic and real was badly computed for
east/west (was using width instead of height, bummer!).
In Corona._createCoreWire(), completly screwed computation of the
side gap, was using a badly initialized value of the "bb" variable.
* Bug: In cumulus/plugins/Chip.py, the computation of the minimal size
for the corona was wrong, do *not* add the size of the pads and
multiply by two as it is done by "inflate". This was forcing the user
to create way to large chips for a given core size.
This commit degrades the run success rate of ARMv2a to 87% (40 iters).
* New: In CRLcore/etc/.../kite.conf, add configuration parameters:
katana.termSatReservedlocal
katana.termSatthreshold
for the new edge capacity computation system.
* New: In CRLcore/etc/symbolic/phenitec06/, add support for N. Shimizu
small I/O pads (supplied in phlib80). Tune various parameters of
Anabatic/Katana to increase routing success.
* Change: In CRLcore/alliance/ap/ApParser, make Pin external components,
so RoutingPad will be build upon in global routing.
Do not complain when a I/O pad has a physical instance that did
not exists in the netlist. Just create it (appeared in phlib80).
When no netlist instance exists in a pad, the pad Cell is still
considered as terminal.
* New: In Etesian::BloatCells, new profile named "3metals" better suited
for two routing metals technologies (i.e. Phenitec).
* New: In Anabatic::RawGCellsUnder, new CTOR which take only source &
target points instead of a segment. Needed to manage wide segment for
which the axis to consider is not that of the segment (one axis for
each track it intersect).
* New: In Anabatic::GCell, add a RoutingPad count attribute, for Edge
reservation computation.
* New: In AnabaticEngine::computeEdgeCapacities(), instead of decreasing
all edges of a fixed amount (hTrackReservedLocal), guess the GCell
cluttering from the number of RoutingPads that it contains.
For non-saturated GCells, the four edges are decreased by the number
of RoutingPads. We use the maximum from the two neigboring GCells.
The hTrackReservedLocal parameter is now used only as a *maximum*
that the edge reservation can reach.
If a GCell is saturated (more than 8 RoutingPads, the saturation is
propagated horizontally to 2 neigboring GCells).
* Change: In AutoContactTerminal::getNativeConstraintBox(), use a more
flexible gauge name matching for terminal vertical extensions correction.
Namely, match all "msxlib*" kind of gauges.
* Change: In AutoSegment::setAxis(), add the ability to force the axis
position, even if it is a non-canonical segment. Maybe needed in the
initialisation steo, before the first canonisation is performed.
* New: In NetBuilder, added new methods _do_1G_1PinM1() and _do_2G_1PinM1(),
to manage coronas for Phenitec designs.
To avoid various side effects from segments being too close from
the north / east side of the routing area, make those segments fixeds.
* Change: In KatanaEngine::annotateGlobalGraph(), the management of wide
wires was wrong. The axis to use to find the underlying GCells is the
one of the track, not of the segment. This was creating bad edge
capacity computation under the power ring of a block and subsequently
routing failures.
* New: In Kanata::Manipulator, added method reprocessParallels(), not used
though, but keep it anyway, might be of use later...
* New: In Kanata::Manipulator, added method avoidBlockage() for terminal
METAL2 in non-preferred direction, restrict the terminal and turn
constraint box at the current position of the perpandicular, so it
doesn't create a deadlock in METAL2.
* Change: In SegmentFsm::conflictSolveByPlaceds(), if we cannot break
using the whole overlap, try the first atomic overlap.
* New: In SegmentFsm::_slackenStrap(), manage conflict between a non-prefered
segment and a blockage, this when to call avoidBlockage()...
* New: In Katana::Configuration, management of the new edge computation
parameters:
katana.termSatReservedlocal
katana.termSatthreshold
* New: In Cumulus/plugins/Core2Chip, support for Phenitec I/O pads.
Now reliably work for 20 successive runs (doRun.sh) with pseudo-random
variations.
* Change: In AnabaticEngine::computeNetConstraints(), fully recompute
the "distance to RoutingPads" for all AutoSegments.
Previously we tried to do it incrementally, but as it's computed
as a minimum, it stayed stuck at the lowest value, event after a
net's change of topology that could made it increase (a new dogleg
did appear between the segment and the RoutingPad).
* Change: In Katana::SegmentFsm::_slackenStrap(), make unbreakable segments
pass through the LocalVsGlobal state so when other try to ripup them
they are prioritary. Otherwise some could go through Unimplemented
directly, without allowing other to attempt to make a detour.
* Change: In Katana::NegociateWindow::NegociateOverlapCost(), when a
global, which is about to be slackened wants to use a track where there
is a segment directly connected to a terminal with a significant
ripup count, mark it as "AtRipupLimit" so it tries to avoid it.
The idea is that globals with high ripup count must avoid terminal
segments because it is likely they will be riped up again so they
better find another track. This was leading to unsolvable configuration
when two segments always want the same track. In this cas, the global
would loose.
* Bug: In Katana::TrackSegment::canSlacken(), never slacken a segments in
non-preferred direction.
* Change: In Anabatic::AutoHorizontal::_slacken(), allow slackening of
segments which perpandiculars are in non-preferred direction, and
not only directly attached to terminals.
* Change: In Anabatic::AutoSegment::canMoveUp(), re-allow segments which
perpandiculars are in non-preferred direction to be moved up.
* Bug: In Katana::Manipulator::moveUp(), when moving up, do not forget
to ripup and reschedule said segment.
This non-deterministic behavior was showing only in the ARMv2a benchmark
around event 180k...
* Bug: In Anabatic::Session::_netInvalidateds & _netRevalidateds, the
set<> was still sorted on pointers. As contacts & segments can be
created to maintain connexity after a layer change, we got a
discrepency in objects Ids that may generate a change in ordering
later.
* Bug: In Katana::Session::_doRemovalEvents(), the set of Tracks that
got elements deleted was still using pointers. Now we use a TrackSet
sorted on (direction,depth,axis). This should not have created
a change in the results, as destructions do not change Ids, but it
genereate extra differences in traces.
* Bug: In Anabatic::AutoSegment::reduceDoglegLayer(), we did not check
that not only source and target depth span was zero, but also both
on the same one. This was seen in the RISC-V where a METAL2 small
segment was demoted into METAL1 causing a gap in the routing (and
a short in the underlying standart cell).
* Change: In Anabatic::AutoHorizontal::_canSlacken(), if the source or
target contact is in a GCell flagged "go straight", do not slacken,
which would create a dogleg. This case is usually meet under big
power rails that render a dogleg impossible to place as all tracks
are used.
Same modification for AutoVertical.
* Change: In Hurricane::SharedName, replace the incremental Id by a hash key.
This is to ensure better deterministic properties. Between use cases,
additional strings may have to be allocated, shitfing the ids. Even if
hash can be duplicated, we should be able to ensure that the absolute
order in map table should be preserved. Supplemental strings are inserted
in a way that keep the previous order.
* Change: In CRL/etc/symbolic/cmos/kite.conf, add "katabatic.routingGauge"
default parameter value ("sxlib").
* Change: In CRL/etc/common/technology.conf, define minimal spacing for
symbolic layers too (added for METAL4 only for now).
* Change: In CRL::Histogram, extend support to dynamically sized histograms.
Add a text pretty print with table and pseudo-curve.
* Change: In Cumulus/plugins/ClockTreePlugin, create blockage under the
block corona corners so the global router do not draw wire under them.
This was creating deadlock for the detailed router.
When the abutment has to be computed, directly use Etesian to do it
instead of duplicating the computation in the Python plugin.
* New: In Etesian, as Coloquinte seems reluctant to evenly spread the
standard cells, we trick it by making them bigger during the placement
stage. Furthermore, we do not not uniformely increase the size of the
cells but create a "bloating profile" based on cell size, cell name
or it's density of terminals. Currently only two profiles are defined,
"disabled" which does nothing and "nsxlib" targeted on 4 metal layer
technologies (aka AMS 350nm, c35b4).
* Bug: In Knik::MatrixVertex, load the default routing gauge using the
configuration parameter "katabatic.routingGauge" as the default one
may not be the first registered one.
* New: In AnabaticEngine::setupNetDatas(), build a dynamic historgram of
the nets terminal numbers.
* Bug: In Anabatic::AutoContact::Invalidate(), always invalidate the
contact cache when topology is invalidated. In case of multiple
invalidations, if the first did not invalidate the cache, later one
that may need it where not allowed to do so. The end result was correct
nonetheless, but it did generate annoying error messages.
* Bug: In Anabatic::AutoContactTurn::updateTopology(), bad computation
of the contact's depth when delta == 2.
* Bug: In Anabatic::Gcell::getCapacity(), was always returning the west
edge capacity, even for the westermost GCell, should be the east
edge in that case.
* New: In Anabatic::AutoSegment, introduce a new measure "distance to
terminal". This is the minimal number of segments separating the
current one from the nearest RoutingPad. This replace the previous
"strong terminal" and "weak terminal" flags.
This distance is used by Katana to sort the events, we route the
segments *from* the RoutingPads *outward*. The idea being that if we
cannot event connect to the RoutingPad, there is no points continuing
as thoses segments are the more constraineds. This gives an order close
to the simple ascending metals but with better results.
* New: In Anabatic::AutoSegment, introduce a new flag "Unbreakable", disable
dogleg making on those segments. mainly intended for local segments
directly connecteds to RoutingPads (distance == 0).
* New: In Anabatic::AutoSegment, more aggressive reducing of segments.
Now the only case where a segment cannot be reduced is when it is
one horizontal branch in a HTee or a vertical on a VTee. Check if,
when not accounted the source & target VIAs are still connex, if so,
allow reducing.
* New: In Anabatic::AutoContact, new state flags CntVDogleg & CntHDogleg
mainly to prevent making doglegs twice on a turn contact. This is to
limit over-fragmentation. If one dogleg doesn't solve the problem,
making a second one will make things worse only...
* Bug: In Anabatic::Configuration::selectRpcomponent(), we were choosing
the component with the *smallest* span instead of the *bigger* one.
* New: In Anabatic::GCell, introduce a new flag "GoStraight" to tell that
no turn go be made inside those GCells. Mainly used underneath a block
corona.
* New: In AnabaticEngine::layerAssign(), new GCellRps & RpsInRow to manage
GCells with too many terminals. Slacken at least one RoutingPad access
when there is more than 8 RoutingPad in the GCell (slacken or change
a vertical METAL2 (non-preferred) into a METAL3).
* Change: In Anabatic::NetBuilderHV, allow the use of terminal connection
in non-preferred direction. That is, vertical METAL2 directly connected
to the RoutingPad (then a horizontal METAL2). This alllows for short
dogleg without clutering the METAL3 layer (critical for AMS c35b4).
Done in NetBuilderHV::doRp_Access(), with a new UseNonPref flag.
Perform some other tweaking on METAL1 access topologies, to also
minimize METAL3 use.
* New: In AnabaticEngine::computeNetConstraints(), also compute the
distance to RoutingPad for segments. Set the Unbreakable flag, based
on the distance and segment length (local, short global or long global).
New local function "propagateDistanceFromRp()".
* Change: In AnabaticEngine.h, the sorting class for NetData, SparsityOrder,
is modificated so net with a degree superior to 10 are sorted first,
whatever their sparsity. This is to work in tandem with GlobalRouting.
* New: In Katana::TrackSegmentNonPref, introduce a class to manage segment
in non-preferred routing direction. Mostly intended for small METAL2
vertical directly connected to RoutingPad. Modifications to manage
this new variant all through Katana.
* Change: In Katana::GlobalRoute, DigitalDistance honor the GoStraight flag
of the GCell. Do not make bend inside thoses GCells.
* Change: In KatanaEngine::runGlobalRouter(), high degree nets (>= 10) are
routed first and whitout the global routing estimation. There should be
few of them so they wont create saturations and we want them as straight
as possible. Detour are for long be-points.
Set the saerch halo to one GCell in the initial routing stage (before
ripup).
* Bug: In KatanaEngine & NegociateWindow, call _computeCagedconstraints()
inside NegociateWindow::run(), as segments are inserted into tracks
only at that point so we cannot make the computation earlier.
* Change: In Katana::Manipulator::repackPerpandiculars(), add a flag to
select whether to replace the perpandiculars *after* or *before* the
current segment.
* Change: In Katana::NegociateWindow::NegociateOverlapCost(), when the
segment is fully enclosed inside a global, the longest overlap cost
is set to the shortest global hoverhang (before or after).
When the cost is for a global, set an infinite cost if the overlapping
segment has a RP distance less or equal to 1 (this is an access segment).
* Bug: In Katana::PowerRailsPlane::Rail::doLayout(), correct computation of
the segments extension cap.
* New: In Katana::QueryPowerRails::addToPowerRail(), add support for Pad.
* Change: In Katana/PreProcess::protectCagedTerminals(), apply the contraints
to any turn connected to the first segment of the RoutingPad so the
perpandicular constraints got propagated to the perpandicular segment...
* Change: In RoutingEvent, cache the "distance to RP" value.
* Change: In RoutingEvent::Key::compare(), sort *first* on distance to
RoutingPad, then layer depth. If both distance to RoutingPad is null,
then sort on segment length.
* Change: In RoutingEvent::_processRepair(), try a repack perpandicular with
perpandiculars first (then with perpandicular last, then give up).
* Change: In SegmentFsm::bindToTrack() and moveToTrack(), set an axis hint
when creating the insertion event.
* Change: In SegmentFsm::_slackenStrap(), add a step through slacken between
minimize and maximum slack (wihch directly end up in unimplemented).
* Change: In Session::_addInsertEvent(), add an axis parameter needed when
the axis of the segment is not the one of the track (case of wide
segments or non-preferred direction).
* Bug: In Track::_preDestroy(), bad management of the TrackElement reference
count. Destroy the segment only when reaching zero...
* Bug: In Track::expandFreeIneterval(), forgotten to manage case when there
is a set of overlaping segments at the "end" of the track, the
EndIsTrackMax was not set.
* Change: In TrackCost::Compare, increase the cost when an overlaping
segment is at it's ripup limit. We should try *not* to rip it up if
we can. Add a dedicated flag "AtRipupLimit".
* Change: In TrackElement, add proxies for isUnbreakable(), new function
updateTrackSpan().
* New: In TrackFixedSegment CTOR, when a supply wire of METAL2 or above is
found, make the underlying GCells "GoStraight".
* New: In TrackElement::canDogleg(GCell*), check for already done perpandicular
dogleg on source/target (reject if so).
* New: In Isobar::PyCell, export the isRouted() and setRouted() to the
Python interface.
* Bug: In CRL::Entity::parseEntity(), check that the closing parenthesis
is the last character of the net name. Issue a more relevant error
message.
* In Anabatic::NetBuilder::_do_xG() and all other unimplemented methods,
throw an error if called from a derived classes instead of just
issuing a message in the debug stream. Avoid later core dumps...
* In Anabatic::NetBuilderHV, implement the builders for GCells with
one pin. Needed to support chip/corona routing.
* Bug: In Cumulus/plugins/Chip.py, check that coronaCk exists before
using it.
* New: In Cumulus/plugins/PadsCorona/Side._placePad(), when routing
a design with symbolic pads, export the chip external "pad"
connectors to be able to perform a lvx (otherwise cougar do not
create external nets).
In Corona._createCoreWire(), set the minimal gap between the pads
and the corona to 6 pitches. Empirical value to avoid DRC errors
with symbolic pads (pxlib).
When successufully done, mark the Corona cell as routed.
* Bug: In Cumulus/plugins/Core2Chip.IoNet, the regex for vectorizet net
was wrong, it was allowing only one digit in the index.
* Bug: In Cumulus/plugins/Core2Chip.cmos, correct management of
pad & corona clock nets. Correct connexion between vdde/vddi.
* Bug: In Unicorn/cgt.py, forgot to execute scripts when in text mode.
* Change: In Hurricane::Error constructors disable the backtrace generation.
(*very* slow).
* Change: In Hurricane::Library::getHierarchicalname(), more compact
naming. Remove the name of the root library.
* New: In Hurricane::Net, new type "FUSED", for component with no net.
More efficient than having one net for each.
* Change: In CellViewer, BreakpointWidget, use Angry Birds icons.
* Change: In CellWidget::State, use the hierarchical name (cached) as key
to the state. This allow to load two cells with the same name but from
different libraries in the widget history.
* Change: In PyGraphics, export "isEnabled()" and "isHighDpi()" functions.
* Change: In CRL/etc/symbolic/cmos/plugin.conf, and
CRL/etc/common/plugin.conf use the physical dimensions converters.
* Change: In CRL/etc/symbolic/cmos/technology.conf, make the GDS layer
table coherent with the default Alliance cmos.rds.
* New: CRL/python/helpers/io.py, put ErrorMessage new implementation here,
along with a new ErrorWidget written in PyQt4. It seems finally that
PyQt4 can be used alongside Coriolis Qt widgets.
New ErrorMessage.catch() static function to manage all exceptions
in except clauses.
* Change: In CRL/python/helpers/, no longer use ErrorMessage.wrapPrint(),
directly print it.
Rewrite the utilities to display Python stack traces "textStacktrace()"
and "showStacktrace()".
* Change: In CRL::AllianceFramework, shorten the names of the libraries.
* Change: In CRL::ApParser & CRL::ApDriver, more accurate translation between
Alliance connectors (C record) and Hurricane::Pin objects. Pin are no
longer made square but thin and oriented in the connecting direction.
Use the new fused net for unnamed components.
* New: In CRL::GdsParser, implementation of SREF parsing, i.e. instances.
Due to the unordered nature of the GDS stream, instances creation are
delayed until the whole stream has been parsed and only then are they
created.
For the sake of reading back Alliance s2r GDS, we assume that any
TEXT following a boundary is the Net name the boundary (component)
belongs to.
Create abutment box for Cells, computed from the bounding box, so
the Hurricane QuadTree could work properly.
Make use of the fused net for unnamed components.
* New: In Cumulus/plugins/chip, complete rewrite of the I/O pad management.
Now we can mix real (foundry) pads and a symbolic core.
To cleanly support the de-coupling between the real part and the
symbolic one we introduce a new intermediary hierarchical level, the
corona. We have now:
Chip --> Pads + Corona --> Core.
At chip level (and if we are using real pads) the layout is fully
real (excepting the corona).
The Corona contains everything that is symbolic. It has symbolic
wires extending outward the abutment box to make contact with the
real wires coming from the pads.
In the pad ring we can use corners instances (or not), pad spacers
or directly draw wires between connectors ring pads.
Provide two flavors: placement only or full place & route.
WARNING: If routing in a second step, *do not route* the *Chip* but
the *Corona*.
* Change: In Cumulus/plugins/clocktree, give the modified Cell an
additional extension of "_cts" (Clock Tree Synthesis) instead of
"_clocked", to follow the common convention.
* New: In cumulus/plugins/S2R.py, encapsulate call to Alliance S2R and
reload the translated Cell in the editor.
* New: In cumulus/plugins/core2chip, provide an utility to automatically
create a chip from a core. To work this plugins must have a basic
understanding of the pad functionalities which may differs from
foundry to foundry. So a base class CoreToChip is created, then for
each supported pad foundry a derived class is added. Currently we
support AMS c35b4 and Alliance symbolic cmos.
* Bug: In Anabatic::Configuration, read the right configuration parameter
"anabatic.topRoutinglayer" (Katana), and not the one for Katabatic...
* Change: In Unicorn/cgt.py, process the plugins in alphabetical order
to ensure a reproductible ordering of the menus...
* Bug: In CRL/etc/symbolic/cmos/plugins.conf, rails dimensions are no
longer expressed directly in lambda. Must be created using helper.l().
* Change: In CRL::ApParser, slightly more smart management of Pin width.
Must normalize Pin behavior between Alliance & Hurricane as in
Alliance they have only one dimension.
* Change: In CRL::LefImport, if a net name end with "!", assume it's a
global one. Have to check this naming convention.
* Change: In Anabatic::NetBuilderHV::_do_1G_1PinM3() & _do_1G_1PinM2()
now implemented. Needed for the corona routing support.
* Change: In AnabaticEngine::setupPreRouted(), exclude segments outside
the abutment box.
* Change: In KatanaEngine::PowerRails, remove the I/O pad support as now
we route only inside the Corona. So only one vdd/vss/ck are supported.
* New: In cumulus/plugins/ChipPlugin.py, complete rewrite of the chip
support:
* Uncouple pad I/O ring whith real cells (foundry) from a symbolic
core. A new intermediate level "corona" is introduced to handle
the real/symbolic transition.
* Ability to explicitly setup position of the pads on the chip side
in case of uneven distribution.
* Enable clock tree to be build with 3 metal only (M2 to M4) instead
of (M2 to M5).
* Change: In Etesian::Configuration CTOR, use the gauge from the
configuration parameter "anabatic.routinGauge" instead of the default
one.
* Change: In Anabatic::Configuration CTOR, use the gauge from the
configuration parameter "anabatic.routinGauge" instead of the default
one.
* New: In Hurricane::IntrusiveMap, introduce IntrusiveMapConst which allow
to search with a "const Key&" instead of a "Key", sparing the copy
construction of the Key.
* Change: In Hurricane::Cell::NetMap, use the new kind of map with
"const Name&" key access. This speeds up the Cell::getNet() method
by suppressing one copy construction of a Name, which are costly
after all...
Should review the whole code to use "const Name&" everywhere it
is possible.
* Change: In Hurricane::Entity & Hurricane::DBo, displace the unique
identifier from Entity to DBo (move up to the base class).This
to allow us to build deterministic map of DBo requireds in
UpdateSession (which is built upon a SharedProperty).
WARNING: This break the JSON database exportation support, do not
use it until fixed/rewritten.
* Change: In Hurricane::Layer, add an attribute to know if a layer is
associated to a blockage. Modificate accordingly PyLayer and
BasicLayer.
* Change: In Hurricane::SharedProperty, the set of owners (DBo*) is now
stored in a std::set sorted on the objects Ids, instead of a simple
vector. The linera search time through the std::vector was starting
to show (ISPD05 bigblue1).
* Bug: In Isobar::PyInstance, make full contructor signature (5 arguments)
conform to the C++ one. It was only accepting the four first and
forcing the placement status to be FIXED.
* Bug: In CRL/etc/symbolic/ispd05/kite.conf, update for the new configuration
requirements where all distance must be converted into DbU in the
file itself (use "helpers.l()", "helpers.m()"). Apply to the cell &
routing gauges.
* Bug: In CRL/etc/symbolic/ispd05/technology.conf, update for the new
configuration. "helpers.initTechno()" *must* by called first thing
in this file in order for the Technology to be created.
* New: In CRL::AllianceFramework, add matchCellGauge() &
matchCellgaugeByHeight()
* New: In CRL::CellGauge, add a flag to distinguish gauges meant for
IO Pads and an "isPad()" predicate.
* Change: In CRL::Ispd05Bookshelf, flush the UpdateSession stack every
1000 elements additions. Maybe not necessary now the the UpdateSession
property relies on a std::set instead of a std::vector.
* New: In CRL::LefImport, support for SITE and match/create the appropriate
CellGauge on the fly. Specific support for MACROS that are flagged PAD.
Add a dedicated post-treatment for PAD connectors, extend them toward
the boundary of the nearest abutment box side. Tested only on AMS 350nm
c35b4 for now.
This part is most likely to be tweaked for every kind of real foundry
pad that we may encounter...
* Change: In EtesianEngine::findYSpin(), use the C++ "for" construct to loop
over Collections.
* Change: In Unicorn/cgt.py, register the Python/C++ tutorial support by
default.
* Bug: In Hurricane::Collection::iterator, the iterator use a locator from
a getLocator() not wrapped inside an auto_pointer like GenericLocator.
So the destructor of the iterator must take care of the deletion.
This was showing more and more as we converted forEach() into the
C++ 11 for syntax.
Seems to decrease the memory use by almost a factor 2...
* Bug: In Dijkstra::_cleanup(), as a double security, cleanup the queue.
* Bug: In Katana::Track::expandFreeInterval(), the OutsideElement case was
not handled correctly, the end index must be increased in that case.
As a result, this function was returning too short an interval.
This was affecting the computation of perpandicular free interval
in DataNegociate::update() for perpandicular fixed but not in a track.
* New: In Anabatic::NetBuilder and NetBuilderVH, now manage GCells with
one Pin, and up to three globals. Used to put terminals at the
edge of a block.
* New: In EtesianEngine, now manage placed Pins.
(done through extractInstanceName())
* Change: In CRL::RoutingGauge::getHorizontalGauge() no longer skip PinOnly
gauges to find the reference one (same goes for vertical).
* Bug: In Anabatic::Edge::getDistance(), remove the additionnal 0.1
added to horizontal edges. This was for testing before the hScaling
parameter was added (to the distance computation in GlobalRoute).
* New: Anabatic::Path_Edges, collectio to walkthrough all the edges
between two node. More complex than in Knik as we are no longer
using a regular grid. We may request the north bound path or south
bound path.
Collection returned by AnabaticEngine::getEdgesUnderPath().
* New: In Anabatic::NetData, add a new flag GlobalEstimated to tell if
the net RMST has been computed (using FLUTE).
* New: In Anabatic::PriorityQueue, used to sort Vertexes by increasing
distances, add a new criterion to be used in case of distance
equality. The attractor which should be the center of the search
area. In case of equality, we choose the Vertex which is closest
to the attractor. Give a small improvement, and more "dendritic"
trees.
For a more simple implementation of the comparison function it is
made as a static member (so no two Dijkstra objects at the same
time...).
* Change: In Anabatic::Edge, make the estimate occupance a floating
point number instead of an integer.
* New: In Katana::GlobalRoute, finally implement the estimated congestion
driven router. Net RMST estimated using FLUTE.
Use the historic cost from Knik implementation and not the one
given in Damien's thesis, which seems not be the same and a bit
strange.
* New: In KatanaEngine, add the ability to exclude nets from routing,
and export it to Python.
* New: Anabatic::AutoContact::setLayerAndWidth() to set both layer and
VIA width/side according to the RoutingGauge. If the delta in zero,
use the metal gauge, and the VIA gauge otherwise.
* Bug: In Anabatic::AutoContactTerminal, Anabatic::AutoContactTurn,
Anabatic::AutoContactHTee & Anabatic::AutoContactVTee, in the
updateTopology() method, set both the layer and the VIA with when
there is a change of layer. Note that this default size may be
overriden later by updateSeize() in the case of non-default width
segments.
* New: In Anabatic::AutoSegment, new overload setLayer(size_t) to set
both layer and segment with according to the routing gauge.
* Bug: In Anabatic::AutoHorizontal and Anabatic::AutoVertical, in method
_makeDogleg(), make use of the new setLayer() to correctly set up
the wire width.
Idem for Anabatic::AutoSegment::changeDepth() and ::makeDogleg(),
and in Anabatic::LayerAssign.
* New: In Hurricane::RbTree, template for red-black tree. Standard
implementation but well integrated in the Hurricane database and
ready to be derived (both iterator and Collection support).
* New: In Hurricane::IntervalTree, template for interval tree, derived
from RbTree.
* New: unittests tool to perform unit tests.
* Change: In Bora::ChannelRouting, now implemented with IntervalTree.
There is something suspicious here : the "thick" version of
addWireoccupation() seems never to be called. Have to check the
wide wire support implementation.
* Change: In Hurricane::CellWidget, set the minimal size to 350 pixels
to fit my normal DPI secondary screen...
* Change: In Hurricane::Error(), reactivate the backtrace generation by
default. Seriously slow down the program each time an Error is to
be constructed.
* Bug: In Analog::Device::preCreate(), check for NULL Technology before
attempting to use it.
* Change: In Hurricane/Analog, remove all '*Arguments*' classes and their
Python interface. It was an obsoleted way of passing devices parameters
to the Python layout generators (located in Oroshi). Now we just get
them straight from the Device with the getParamter() method.
* Change: In CRL::System CTOR, add Python pathes for Oroshi & Karakaze.
* Change: In Oroshi/Python/WIP_*.py layout generator scripts, remove
all uses of the "Arguments". Directly access the parameters through
the device itself. Make the checkCoherency() with identical arguments
as of layout().
* New: Bora tool that performs analog place & route. Based on a slicing
tree representation. It is the thesis work of Eric Lao.
Code beautyfication and some programming cleanup.
* New: Karakaze tool, provide the Python base class AnalogDesign used
to build an analog design. Create/configure devices and assemble
them in a slicing tree.
* Change: In Unicorn/cgt.py, display the stack trace in case of an
ImportError exception as well as for other exceptions.
Add Bora to the set for included tool engines.
Jean-Paul Chaput