* Bug: In Track::repair(), consider the blockage net as any other, so
the metal filling works correctly (correct management of transitions
between blockage and non-blockage).
* Change: In Katana::PowerRails, in TerminalNetlist cells instances,
the ordinary nets components where generating obstacles, leading
to stupid cross blockages between the obstacle generated by the
component supporting the routing pad and the RP itself.
Now only take into account supplies and clocks (any layers)
and blockage layers.
Fix symbolic benches.
* Change: In Katana::Manipulator::moveUp(), the "reserve" value was
of 0.5 for pivot up and locals, now set it to 1.0, like in all
other cases ("reserve" is the number of free tracks that is
needed to allow the move up, in addition the the length being
moved up).
Fix routing convergence on the MIPS pipeline bench.
* Bug: In Track::repair(), when a same net gap has been found and closed,
we display a warning. We display the two segments fused, but when it's
the two first, we must not use index "i-1" (with i=0) ...
* Bug: In Katana::GlobalNetTable::getRootNet(), look for all fixed nets,
not only supplies and clocks. There may be some as now H-Trees are
not limited to clocks.
Should solve ao68000 short circuit cases.
* Change: In Track::addOverlapCost(), in some configuration, we can
have two overlapping short segments that can *both* be realigned.
But they prevent that because we account their shared length on
the track.
So now, in realign mode only, do not account same-net shared
length if the segment length is less than *two perpandicular pitches*.
This helps the antenna protection by making the diode connected
directly to METAL2 long stripes, and not keeping them isolated.
* Change: In Katana::Track::addOverlapCost(), if an overlaping segment
is owned by the net *and* is the one we want to insert, do not take
it into account in the shared length.
This case never occured before we introduced the "realign" stage,
as a to be inserted segment, was, by definition, not already
inserted in a track. But in the realign stage, it is. So we should
not account it when computing the insertion cost in the track it
is already in. This was preventing short segments (less than a
pitch) to be correctly re-aligned.
And, as a side effect, preventing the antenna/diodes to work as
intended (diode connected at METAL3 layer while the antenna occur
at METAL2 layer).
* Change: In SegmentFsm::_slackenLocal(), in the Minimize state, when
the segment is fully blocked *and* has *lot* of candidate tracks,
that means that it is up against a *massive* blockage (i.e. a macro
block). In that case, try to move up (to go *over* it).
Previous behavior was to go straight to Inimplemented state.
* Change: In SegmentFsm::_slackenGlobal(), manage fully blocked
global segments. But finally, this configuration didn't arise.
* Change: In Manipulator::moveUp(), restore the management of the
AllowLocalMoveUp flag, to be able to move up local segments
(needed by SegmentFsm::_slackenLocal()).
* New: In Track::repair(), the gapset was used to *close* same-net gaps
is now alos used to restore minimal spacing between different nets.
Seems to be not fully working yet.
* In KatanaEngine:
- Former situation:
Each RoutingEvent did store the routing stage it was in. And it
was misnamed "mode".
- New organization:
The routing stage is stored in KatanaEngine itself. It can be
accessed through a proxy in Session.
* Change: In DataNegociate::update(), when in Realign stage and computing
non-preferred perpnadicular routing *do not* expand of one pitch
outside the RoutingPad range.
* Bug: In TrackSegment::getFreeInterval(), if, for whatever reason,
a discrepency happens between the TrackSegment and the Track,
that is the _track fields point to a *wrong* Track. Then the
index lookup will fail (Track::npos), so return an all-span
interval instead of trying to expand it and crash (out of
bound).
* New: In Track::repair(), short gaps between segments of the same
nets where occuring and being not detected. This was causing
DRC minimal distance violations. Now, fuse the segments when
they are too close. Done by extenting the duSource of the
rightmost one to the leftlost one.
Create ancillary class GapSet to manage the gaps of the
various segment of the same net.
When a segment is placed only once (which is to say it is nerver ripped
up) it can sometimes end-up in a non-optimal place. We now add a stage
in Katana where each segment is "re-placed" in order to maximise
alignment on it's neighbor. This is a new stage added to both
RoutingEvent and NegociateWidow. Segments are replaced *only* in free
space, they will not ripup *other* segments, except for their own
perpandiculars. We exclude from re-placement globals (unlikely to move)
and segment that have reduced perpandiculars which *must* not be elongated
and potentially raised.
Add a new katana setting to enable/disable the realign stage (enabled
by default:
- "katana.runRealignStage" ( = True )
We use the segments extensions (dxTarget & dyTarget) to enlarge if
needed the segments. This new implementation is completely at
Anabatic level and should not be seen (i.e. managed) at Katana level.
* Change: In AutoHorizontal & AutoVertical, change the semantic of
getSourceU() and getTargetU(). formerly they where the end
position of the segment (with extension included), now they
gives the position of the anchor contacts, that is the axis
of the perpandiculars.
* New: AutoSegment::getLength() is still a proxy toward the
Segment::getLength() which returns the length of segment with
dxSource & dxTarget. We introduce a getAnchoredlength()
which returns the length between the centers of the S/T
anchors. That is axis to axis.
This is this length which is now used througout Anabatic.
* New: In AutoSegment::_extentionCaps, add a fourth item to hold
the segment minimal length (to respect minimal area given
the wire width).
* New: In AutoSegment::getExtensionCap(), if the segment has
a non-zero S/T extension, returns it instead of the S/T
contact extension *if it is greated*. The check of the
extension can be disabled by the Flag::NoSegExt flag.
* Change: In AutoSegment::isMiddleStack(), security check on
the presence of source and targets. More accurate detection
of perpandicular in "same layer" with a non-zero length,
So the area is OK, even with a short segment.
* New: AutoSegment::expandToMinLength(), check if a segment is
under the minimal length and expand it if need be by playing
with the dxTarget & dxSource. Tag minimal segments with the
AutoSegment::SegAtMinArea flag. Also try to keep the segment
*inside* it's former (supposedly wider) interval.
* New: AutoSegment::unexpandToMinLength(), to be called on a
formerly minimal sized segment which as grown up. Reset
it's S/T extensions to zero and unset the flag SegAtMinArea.
* Change: In AutoHorizontal::updateOrient(), when the extension
are non-zero, also swap them if needed, to keep the exact
footprint of the segment.
* New: In AutoSegment::revalidate(), check that the segment
respect the minimal length (area), and expand it if needed.
Conversely, if the segment has grown up from a minimal
length state, reset it's extensions to zero.
* Change: In Anabatic::Session::revalidate(), invalidateds
segments are now sorted in such a way that the "middle stack"
ones are revalidateds last. Not recall 100% why...
* New: In Katana::TrackCost, add a computation of the free interval
length we are into (if any). Not used yet, keep it for future
use.
* Change: In KatanaEngine::finalizeLayout(), remove the call to
segments minimum area protection. It is now obsoleted by the
new implementation in Anabatic.
* Change: In Track::check(), call the minimum size/area checker
Track::checkMinArea().
* Change: In NetBuilder::getPositions(), ordering of source/target points
is now integrated to this function instead of left to the caller.
In case of real (non-symbolic) routing gauge, skrink the ends of
half the wire width.
* Change: In NetBuilderHV::doRp_AutoContacts(), in case of non-METAL1
RoutingPad, put the axis of the segment on the nearest track.
Issue a warning if we have to shift, as it may be a potential
source of routing problems.
* New: Anabatic::Session::getNearestTrackaAxis(), proxy to compute
track positions, knowing the design abutment box.
* Bug: In Katana::PreProcess::propagateCagedConstraints(), when
looking at all the slave components anchoreds on a RoutingPad,
if they do not have an AutoSegment lookup, skip them instead
of crashing.
* New: In cumulus/plugins.block.Block.placeMacro(), new method to
place a macro cell, partly delegating to the Macro block wrapper.
Must be called *after* both core and corona abutment boxes have
been set.
Adjust the macro block position so the METAL2 & METAL3 pins
are exactly on pitch regarding the full routing grid. The reference
being the corona.
A shift, less than one pitch may be applied, leading in some
cases of overlapping abutment boxes. But this shouldn't be a
problem.
The macro to place is designated through a path of instances
names, rooted at the *core* (not the corona). Meaning that the
head instance must be one of the core.
* Change: In cumulus/plugins.chip.Chip, the complete chip I/O pads
plus corona and core placement is moved out from doPnR() and
put into doChipFloorplan(). It is now mandatory to call this
method *before* doPnR().
Those methods are now cleanly separated so we can perform macro
block placement or any inner core floorplaning operations between
them.
* Change: In cumulus/plugins.macro.Macro, instead of creating large
pads for the I/O pins so whatever the block position, they will
be under a grid point, create a simple dogleg to put them on
grid.
To ensure that they are "on grid", the block pins must be
in METAL2 (horizontal E/W) or METAL3 (vertical N/S) and the block
is assumed to be placed so the bottom left corner of it's
abutment box is exactly on one grid point for M2/M3.
This should be done by Block.placeMacro().
* Bug: In PowerRailsPlanes::Rail::doLayout(), in case of non-blockage but
fixed segments (that is, power lines), expand the segment box of one
picth to put blockage on too close neigboring tracks.
* Change: In Manipulator::avoidBlockage(), more accurate computation of
the blocked area for pushing aside the terminal & turn of the non-pref
segment.
NOTE: To myself, one more bug uncovered in the Track segments management.
This is really too complex, must find time to re-think and simplify
the whole thing.
* New: In Katana::NegociateWidow::createTrackSegment(), detect offgrid
fixed segments and insert them into tracks directly (as *wide* segment
of two tracks).
* New: In Katana::TrackSegment::create() factory method, check for offgrid
fixed segment and use a TrackSegmentWide (of 2 tracks) for them.
* New: In Katana::TrackSegmentWide CTOR, check if they are used in the
context of an offgrid segment and in that case set the track span
to two. We *do not* manage yet the case for both *wide* and *offgrid*
segments.
* Change: In Katana::PowerRails::Rails::doLayout(), do not expand blockage
rectangles over their real size. Add the guard only for real layers
segments.
* Bug: In Katana::PreProcess::propagateCagedConstraints(), when looking
for the first track index, check for out of bound value (npos).
* Bug: In Katana::Track::addOverlapCost(), before using the overlap
segment indexes, check if we are not in a free hole (get the free
interval from center).
* Bug: In Katana::Track::expandFreeInterval(), the interval was badly
computed if it was included inside segments of another (same) net.
under the fixed segment, we were using the axis *of the segment*,
but if it is very wide, this is completly off.
Now use the axis of the *track* to get the right GCells impacteds.
* Bug: In KatanaEngine::annotateGlobalGraph(), overlapping blockages or
fixed segments where taken into account as separate ones. This was
making the edge capacity reservation too high. Creating false
zero-capacity edges at some points.
Didn't show up until now because we did not have overlaps.
* Change: In EtesianEngine::globalPlace(), disable the call to
antennaProtect(). First reason is that, after all, Coloquinte
do not handle so well the resizing of the cells "on the fly",
it overspill the boundaries sometimes. Second reason is that
as we cannot know the routing tree at this stage, we will not
be able to choose the correct points for diode insertions.
We only have a Steiner tree wich may not be the same as a
density driven Dijkstra.
* Change: In Etesian::Area, the Occurrence to the Instances where
not stored in a uniform way. Some where starting from the
placed sub-block, some where starting from the top level
(corona), making their processing (and remembering it) tricky.
Now, they are all expressed from the top cell (corona).
The coordinate system is now systematically the one of the
top block (*not* the block).
Create various overloaded functions EtesianEngine::toCell()
and EtesianEngine::toBlock() to ease Occurrence & coordinate
translations.
* New: In Etesian::Slice::createDiodeUnder(), add a X position hint.
Search is done by going through the whole slice range and
minimizing the distance to the hint. If it starts to be too
slow, we may optimize.
* Bug: In EtesianEngine::toColoquinte(), the placement of the top
level external pins was not taken into account (this at last
explain their weird positioning).
* New: AnabaticEngine::antennaProtect(), new algorithm to avoid
antenna effect. This step must be done *after* global routing
and *before* detailed routing. This way we have access to the
real routing and can mend it (along with the netlist) to
insert diodes at the rigth points.
From the global routing we build clusters (DiodeCluster) of
RoutingPads connected through a set of wire whose total length
is below the antenna effect threshold. Long wires connecting the
clusters are also tagged because we need to put a diode between
them and the first RoutingPad of the cluster. This is to avoid
a long METAL2 wire connecting to the RoutingPad before the diode is
connected through METAL3 (in case of misalignment).
This protection is not even enough. For *very long* wires, we
needs to put *more* than one diode (this is to be implemented).
Integrate new features and bug fixes so the Arlet 6502 benchs successfully
passes real DRC with reference industrial tools. Short summary:
* Manage minimum area for VIAs in Katana::Tracks.
* Allow different wire width for wires perpandicular to the prefered
routing direction.
* StackedVIAs used in the clock tree no longer assume an uniform
routing grid (same offset & pitch all the way up).
* Some hard-coded patches in PowerRails for FlexLib.
* New: In CRL/symbolic/cmos/kite.py & cmos45/kite.py, update the
RoutingLayerGauges by adding the new PWireWidth parameter.
Always zero in case of symbolic layout (too fine tuning).
* New: In CRL::RoutingGauge, add accessor to PWireWidth parameter.
Modify the clone method.
* New: In CRL::RoutingLayerGauge, add new parameter "PWireWidth"
to give the width of a wire when it not drawn in the prefered
routing direction. If it is set to zero, the normal width is
used.
* New: In CRL::PyRoutingGauge, export the updated constructor
interface. It is *not* backward compatible, one must add the
PWireWidth parameter in the various kite.py configuration
files (in etc/).
* Change: In AnabaticEngine::_gutAnabatic(), disable the minimum
area detection mechanism, replaced by a more complete one in
Katana::Track. Left commented out for now, but will be removed
in the future.
* Change: In Anabatic::AutoContact::updateLayer(), now systematically
calls setLayerAndWidth() to potentially resize the VIAs. This is
needed in real mode as VIAs are *not* macro-generated but have
their real final size.
* Change: In Anabatic::AutoContact::setLayerAndWidth(), select the
width and height of the contact using the gauge wire width *and*
perpandicular *wire width*.
* Change: In Anabatic::AutoSegment::_initialize(), the "VIA to same cap"
to PWireWidth/2, this will be the size of the VIA in the
non-preferred direction at the end cap (non-square in real mode).
* Change: In Anabatic::AutoSegment::getExtensionCap(), makes different
cases for symbolic and real. Use raw length in real, add half the
wire width in symbolic.
Add a flag to get the extension cap *only*, not increased of
half the minimal spacing.
* Change: In Anabatic::AutoSegment::bloatStackedStrap(), enhanced,
but finally unused...
* New: In Anabatic::AutoSegment::create(), use the PWireWidth when
the segment is not in the preferred routing direction (and of
minimal width).
* New: In Anabatic::Configuration, add new getPWirewidth(),
DPHorizontalWidth() and DPVerticalWidth() accessors.
* Change: In AnabaticEngine::setupPreRouteds(), skip components in
in "cut" material. We are only interested in objects containing
some metal (happens in real mode when VIAs cuts are really there).
* New: In Katana::PowerRailsPlanes::Rail::doLayout(), add an hard-coded
patch that artificially enlarge the *wide wire* so the spacing for
wide wire is enforced. For now, two pitches on each side for
"FlexLib" gauge.
* New: In Katana::Track, add support to find and correct small wire
chunks so they respect the minimum area rules.
Two helper functions:
* ::hasSameLayerTurn(), to find if a a TrackElement as non-zero length
perpandicular is same layer connected to it.
* ::toFoundryGrid(), to ensure that all coordinates will be on the
foundry grid (may move in a more shared location).
* ::expandToMinArea(), try to expand, *in the routing direction*
the too small wire so it respect the minimal area. Check for the
free space in the track.
Track::minExpandArea() go through all the TrackElements in the track
to look for too small ones and correct them.
* Change: In Katana::RoutingPlane, add an accessor to get the tracks.
* New: In KatanaEngine::finalizeLayout(), add a post-treatment to find
for minimal area violations.
* Change: In cumulus/plugins.block.configuration.GaugeConf, add a
routingBb attribute that will serve as a common reference to all
the functions calculation track positions. We must not have two
different reference for the core and the corona. The reference
is always the corona when we working on a complete chip.
* New: In cumulus/plugins.block.configuration.GaugeConf.getTrack(),
Simplified and more reliable way of getting tracks positions.
Use the routingBb.
* New: In cumulus/plugins.block.configuration.GaugeConf.rpAccess(),
Make use of getTrack() to get every metal strap on the right
X/Y position.
* New: In cumulus/plugins.block.configuration.GaugeConf.expandMinArea(),
As those wires are left alone by the router, it is our responsability
to abide by the minimal area rule here. Hence the code duplication
from the router (bad).
Mainly wires made for the clock tree, I mean.
* Bug: In cumulus/plugins.chip.configuration.ChipConf.setupICore(),
the core instance must be placed on the GCell grid, defined by the
slice height (X *and* Y).
* Bug: In cumulus/plugins.chip.corona.Builder(), forgot to use bigvia
for the corners of the inner ring.
* Bug: In cumulus/plugins.chip.pads.corona._createCoreWire(), hard-coded
patch for LibreSOCIO, the power/ground connectors toward the core
are too wide and can create DRC errors when put side by side.
Shrink them by the minimal distance.
* Bug: In Anabatic::AutoSegment::reduce(), no longer reduce *again*
an already reduced segment.
This bug was seen through a side effect, it was causing the
"reduced perpandicular" counter to be incremented too much and
so it cannot get back to zero, blocking the layer reduction
(AutoSegment::reduceDoglegLayer()) and some bad VIAs where left
over.
More debug information in reduce & raise functions.
* Change: In Katana::Session::_revalidate(), process to be raised
segments *before* segments that can be reduceds.
Note: To implement this in a more flexible way we should introduce a
concept of Instance/Cell "placeholder" to reserve space
transhierarchically.
* Change: In EtesianEngine::toColoquinte(), when placing only one block
in a cell, the cell itself can contains other fixed instances
that are over the placement area. Create dummy fixed instances
to reserve the taken space.
In EtesianEngine::AddFeeds(), do not put feed cells over the
cell area occuped by the sibling instances cells.
* Cleanup: In KatanaEngine::setupPowerRails(): small cleanup.
* New: In Hurricane::NetRoutingProperty, add and change the meaning
of the following flags:
- ManualGlobalRoute : now means that a global routing *trunk*
is present, made of "gmetalh", "gmetalv" & "gcontact".
- Manualdetailroute : added, get the former meaning of
ManualGlobalRoute, that is, the detailed routing is
already present for this net, but can be changed by the
detailed router. Implies that it respect the Terminal,
HTee & VTee structuration.
* New: Add Anabatic::Diskstra::loadFixedGlobal(), to account
a manually global net into the edges capacities.
* New: In Anabatic::Edges::ripup(), exclude manually global routed
segments from the ripup. Change the segment sorting function
so that thoses segments are put in head of list (considered
as "smaller").
* Change: In AnabaticEngine::setupPreRouteds(), now detect manual
global routed and manual detail routed signals, and tag them
accordingly.
* New: In AnabaticEngine::Configuration & Session, add proxies
for the global routing layers ("gmetalh", "gmetalv", "gcontact").
* New: In Anabatic::Constants, add flags for global fixed and
detail routed nets.
* Change: In KatanaEngine::updateEstimateDensity(), now use int64_t
for flute coordinates.
* New: Add CRL::RoutingGauge::hasLayer(), to know if a layer is
managed by the gauge (comparison by mask).
* New: In flute, added a Python binding. Contains two methods: "readLUT()",
to load the POWV9.dat and POST9.dat and "flute()" to build a RSMT.
"flute()" takes a tuple of positions (themselves 2-uple) like:
( (x0,y0), (x1,y1,), ... (xN,yM) )
and returns a tuple of 3-uple of branches:
( (n0,x0,y0), (n1,x1,y1), ... )
In "flute.h", set the distance type (DTYPE) to int64_t to always
accomodate DbU::Unit.
As it now uses the Hurricane Python interface and the path utilities
from CRL Core, move it's compilation *after* them (see build.conf in
bootstrap).
* New: In Katana::Manipulator::moveUp(), if the length of the wire is
greater than 60 pitchs, increase the reserve from 0.5 track to
1.0 track. This is to left more free tracks when lots of very
long segments are moved up. Make the run 17 of the ARM test bench
pass.
* New: In Katana::Configuration, two new parameters hTrackReservedMin
and same for V. Forced decrease of all edges capacities, to use
when the global router is too optimistic...
* Bug: In Hurricane/Commons.h, modify the getRecord<>() templates so
that for both vector<Element> and vector<Element*>, the individual
record created for each element are donne with pointers. That is,
for the vector<Element> case, we take a pointer.
As a general policy, except for the POD types, always use pointers
or references to data in the records/inspector. Never uses values
that can call the copy constructor.
Suppress INSPECTOR_PV_SUPPORT() macro, keep only
INSPECTOR_PR_SUPPORT().
Provide value support only for getString<>() template.
This value & copy constructor problem was causing a crash when
trying to inspect Hurricane::AnalogCellExtension.
* New: In Hurricane::Technology, change the API of the PhysicalRule,
now we can only create/get PhysicalRule, but setting the value of
the rule itself must be done on the rule.
Enhance PhysicalRule to provide for stepped rules, non isotropic
and ratio rules.
Merge TwoLayersPhysicalrule in PhysicalRule, much simpler to
suppress the management of derived classes. That means that we
loose a little memory as some fields are mutually exclusive.
Not a problem considering that there will not be so many of thoses
objects.
* New: In CRL/helpers.analogtechno.py, enhanced DTR support for rules
like:
('minSpacing' , 'metal1', ((0.4,20.0), (0.8,1000.0)), Length, 'REF.1')
('minEnclosure', 'metal1', 'cut1', (0.2,0.3) , Length, 'REF.2')
('minDensity' , 'metal1', 0.30 , Unit , 'REF.3')
The DTR parser has been updated, but not the oroshi.dtr Rule
cache for analog components. Given a rule name, the value used
will be the horizontal one of the first step.
* Change: In hurricane/doc/hurricane, re-generate the documentation
with updated support for Technology & PhysicalRule.
* Bug: In EtesianEngine::place(), reset the placement *only* if we are
*not* placing a sub-block *and* the top cell abutment box is empty.
* Bug: In EtesianEngine::place(), set the instance placement status of
all intermediate instances to PLACED, so the AP driver will save
them (we were having partially saved layout when using hierarchical
designs).
* Bug: In EtesianEngine::resetPlacement(), reset the PLACED flag and
the abutment box on the top cell or sub-block to be placed.
* Change: In CRL::LefParser::_macroCbk(), create a Catalog entry for the
newly read MACRO (that is Cell) and sets the Logical, Physical,
InMemory and TerminalNetlist flags.
* Bug: In CRL::LefParser::_siteCbk(), check for NULL cell gauge.
* New: In CRL::AllianceFramework, add setCellGauge(), to set the default
cell gauge. Exported to Python.
* Change: In CRL/etc/common/technology.py, create variables for VIA
layers, so we can modify their properties afterwards.
* New: In CRL/etc/node45/freepdk45, port the configuration files to the
new Python "importable" format.
Note: in kite.py, all the gauges (Routing & Cells) must be named
"LEF.CoreSite" to please my LEF parser, so it can match the gauge
name with the SITE name for standard cells.
* Bug: In Anabatic::NetBuilderVH::_do_2G(), forgotten to be reimplemented
from the base class. Simply redirect to _do_xG().
* Change: In Katana::PowerRailsPlanes::PowerRailsplanes(), create plane
from the layers in the RoutingGauge and their associated blockages
instead of sweeping through all the basic layers.
Allow to distinguish bewteen "METAL" (symbolic) and "metal" (real).
* Bug: In Katana::NegociateWindow::createTrackSegment(), *fixed* AutoSegment
in conflict with blockage where removeds. This was creating "holes"
in the Anabatic articulated segment structure. Now just *don't*
create the TrackSegment. Pass the regression tests, but not sure
it is not generating problems elsewhere.
* New: AnabaticEngine::checkPlacement() to issue more clear errors about
a defective placement.
* New: In Anabatic::NetBuilderHV(), added configurations to manage
one Pin M3 + one M1 terminal plus 2 & 3 globals:
* _do_2G_1M1_1PinM3()
* _do_3G_1M1_1PinM3()
They were occuring for the first time in soclayout/experiment7
in the "flat" approach.
* New: In Katana::runNegociate(), mark the newly routed netlist as
"NetlistTerminal" so it is not placed and routed *again* when
reused as an instance (mostly interract with Etesian).
* Bug: In CRL::VstParserGrammar & VstParserScanner, when loading the
instances models, we where loading both logical & physical views.
This was causing cases of reentrency of the parser, with reset
of the lexer static dictionary, leading to memory corruption.
Now the identifiers are stored in the YaccState of each
parsed cell and we only recursively call for the logical view.
* Change: In CRL::ApParser::_parseInstance(), recursively load the
physical views as they are no longer loaded by the Vst parser.
* Change: In CRL::AllianceFramework::getCell(), sets the
TerminalNetlist flag from the state (mode 'C' in CATAL) onto
the cell.
* Change: In EtesianEngine::loadLeafcelllayouts(), new functions to
load the layouts of the leaf cells if only the netlist has been
loaded.
* Change: In all tools, FindTOOL.cmake, no longer use LIB_SUFFIX to
search for tool libraries but try "lib64/" then "lib/".
* Change: In bootstrap/socInstaller.py, take Debian 10 into account.
* Change: In bootstrap/docker, move from Debian 9 to Debian 10.
In the Cell/Instance hierarchy, the "terminal" and "leaf cell" concepts
where not clearly defined and partially overlapping. Now, "Terminal" is
the refer to the physical hierarchy (layout) and "TerminalNetlist" to
the logical hierarchy (netlist). The logical hierarchy can be less deep
than the physical one thanks to a Cell dedicated cell flags. Collections
related to the physical hierarchy keep their old names, the one related
to the logical hierarchy are renamed from "Leaf" to "TerminalNetlist".
The name "Leaf" was too ambiguous (leaf for *what* hierarchy).
* Change: In Hurricane::Device, set the "TerminalNetlist" flag once and
for all. No need set it in all the derived classes again.
* New: In Hurricane::MultiCapacitor, added new parameter "dummy" to
create dummies around the capacity matrix.
* Change: In Hurricane::Cell, remove "Leaf" related methods, replace
them by "TerminalNetlist" one, especially Collections. Now we have
two clear sets of Collections to walkthough the layout or the
netlist.
Change the "Terminal" flag into "TerminalNetlist".
* Change: In Hurricane::CellCollections, rename "Leaf" into
"TerminalNetlist" collections and apply the new semantic to the
locators.
* Change: In Hurricane::DataBase, Leaf to TerminalInstance renaming.
* Change: In Hurricane::DeepNet, Leaf to TerminalInstance renaming.
* Change: In Hurricane::HyperNet, Leaf to TerminalInstance renaming.
* Change: In Hurricane::Instance, Leaf to TerminalInstance renaming.
* Change: In Hurricane::Viewer::HierarchyInformations, Leaf to
TerminalInstance renaming.
* Change: In CRL::AllianceFramework, Leaf to TerminalInstance renaming.
* Change: In CRL::Catalog, Leaf to TerminalInstance renaming.
* Change: In CRL::ApParser, Leaf to TerminalInstance renaming.
* Change: In EtesianEngine::AddFeeds, Leaf to TerminalInstance renaming.
* Bug: In EtesianEngine::resetPlacement, move there the loop over
non terminal netlist instances to flag fully placed sub-blocks
as terminal for the netlist. Only then remove the feed cells
from unplaced instances. Previously, the feed cells where stripped
even from already placed instances.
* Change: In Katana, Leaf to TerminalInstance renaming.
* Bug: In Bora::PyDSlicingNode, allow the range parameter to be the
Python None object when we do not want to pass one but need to
have it as positional parameter.
* Change: In Cumulus/clocktree/ClockTree.py, Leaf to TerminalInstance
renaming.
* New: In Hurricane::Cell::isLeaf(), a leaf cell was defined as one
without instances. Now it can be software defined with the
"FlattenLeaf" state. If it is flagged "flatten leaf" is will be
considered as a leaf by the trans-hierarchical walkthrough.
This flag is also set for Cells in the Alliance CATAL.
* New: In Hurricane::Cell_LeafInstanceOccurrences::progress(), add a
test to prune leaf cells.
* Bug: In Hurricane::getComponentOccurrences(), when calling the
locator constructor, the "withLeafCells" argument was forgotten
and was getting the value of "doExtraction" (wich, fortunately,
was the same).
* Change: In Hurricane::HypreNet_LeafPlugOccurrences::progress(),
prune the leaf cells instead of the terminal ones.
* Change: In Hurricane::HypreNet_ComponentOccurrences::progress(),
prune the leaf cells instead of the terminal ones.
* New: In Hurricane::Cell, add a "useFlattenLeaf" mode to take into
account or ignore the "FlattenLeaf" flag when doing trans-
hierarchical walkthrough.
Not sure if it shouldn't be systematic.
* New: In Etesian::toColoquinte() and other, activate the "FlattenLeaf"
mode for all walkthough. So we can stop at already placed sub-blocks.
* Bug: In Etesian::toColoquinte(), when placed sub-block where present,
the number of instances was under estimated, so the instance array
was oversized and the end went unitialized. So we were getting all
kind of strange behavior from Coloquinte...
Now throw an exception if the number of instances differs from
the computed size.
* Bug: In Etesian::toColoquinte(), as for the instance array, now
correctly compute the size with the ecluded nets (supplies, clocks).
* Bug: In Etesian::resetPlacement(), event if the Cell is unplaced,
go through the instance list to remove the potential feed cells.
The netlist is written back after placement *with* the feed
cells added. So, when loading again, they where cluttering the
netlist and giving feed redefintions warning. They also generated
erratic behaviors.
* New: In Anabatic::NetBuilderHV, added configurations for:
* 1G_1M1_1PinM3
* 1G_xM1_1PinM2
* 2G_xM1_1PinM2
* doRp_AccessNorthPin
* New: In Anabatic::NetBuilderHV, added Pin management in SingleGCell.
* Bug: In Anabatic::NetBuilderHV::_do_xG_1PinM3(), the North/South
global routing configuration was forgotten (only East/West).
* Bug: In Katana::TrackFixedSegment, the blockage net was a static
variable initialized at the first run. So we were getting stuck
with the blockage net of the first cell to be routed. Of course,
it did show only when Katana was run multiple times in the same
process.
* New: In CRL/etc/node600/phenitec, ported configuration of Phenitec 0.6um
Compliant with DataBase reset.
* New: In CRL/python/helpers, added function "unloadUserSettings()" to
unload Python modules prior to a full reset.
Added "resetCoriolis()" to perform full DataBase reset.
* Change: In CRL::AllianceFramework, make it a derived class of DBo so
the destroy() is now provided.
* Bug: In CRL::AllianceFramework::getCell(), do not attempt any load if
the library list is empty. Should never occur except in case of a
botched databse reset.
* New: In CRL::AllianceFramework, new method "saveCATAL()" to write back
the catalog of a library and "saveCells()" to write back the cells.
Note: only cells actually loaded in memory will be write back.
* New: In CRL::Catalog, add method "saveToFile()" to write back the CATAL
of a library.
* Change: In CRL::ParserDriver, replace "const string&" by "string"
(improved string support of the GNU STL).
* Change: In CRL::ParserSlot, use string instead of Name.
* Change: In CRL::ApParser, make _layerInformation an ordinary attribute
instead of a static one. This allow for it's correct resetting
across databas resets.
* Change: In CRL::VstParserGrammar, reinitialize Vst::framework at each
parser call. Needed to support database reset.
* New: In Hurricane::DBo, add an object counter to be sure that when
we perform a reset, no remaining DBo is allocated. This is different
of the object id which is ever increasing.
Note that, at reset, we check against "1" remaining element as at
this point only Database is still allocated.
Add a new "resetId()" method. MUST NEVER BE CALLED except by
DataBase::_preDestroy().
* New: In Hurricane::Database, new clear() method to remove the Cells
of all the libraries in reverse hierarchical depth order.
Make use of the new CellsSort class.
* Change: In Hurricane::DataBase::_preDestroy(), call "clear()" and
DBo::resetId().
* Change: In Hurricane::Breakpoint, change the default callback to be
a static function. So we can restore it later.
* Bug: In Hurricane::Instance::_preDestroy(), there was yet another
loop of deletion over a collection for the shared pathes.
Replace it by the repetitive deletion of the first element.
* Bug: In Hurricane::Net::_preDestroy(), RoutingPads must be destroyed
prior to any other component.
* New: In Hurricane::ColorScale, add a "qtFree()" method for freeing
the Qt Brush, Pen & Color.
* New: In Hurricane::DrawingStyle, add a "qtFree()" method for freeing
the Qt Brush, Pen & Color.
* New: In Hurricane::Graphics, add a "disable()" method to call the
various "qtFree()" of the sub-objects.
* Change: In bootstrap/FindBoostrap.cmake, remove the -fsanitize=address
as it requires the "san" librarie which may be difficult to install.
* Change: In CRL/symbolic/cmos45/kite.py, decrease the METAL3 pitch from
10l to 8l. This is for testing with 4 routing metal only technology
like AMS c35b4 symbolic.
* Change: In Katana/BloatProfile, add static bloat option, that is, only
cell bloated in the first pass will be bloated again in subsequent
ones.
Add a "katana.bloatOverloadAdd" parameter to more easily control the
amount added to the computed overload.
* Change: In Oroshi, start integration of multi capacitors as generator.
Translate generator parameter into CapacitorStack ones. Add code for
routing unit capacitor.
* Change: In Hurricane::Viewer::ExceptionWidget & CRL/python/helpers/io.py,
downscale icons for non-HiDPI screen.
* Change: In CRL/etc/common/display.py, change the display threshold of
METAL1 layer so it do not appear at high scaling.
* New: In Etesian, activate the "setFixedAbHeight()" feature and export it
to Python. Allows to increase the space margin at constant height.
To be used by the P&R conductor.
* Change: In Unicorn/cgt.py, when running a script, insert the current
working directory at head of the sys.path, not at the end. So installed
modules do not shadow local one.
* New: In Anabatic::Edge, new accessor "getRawcapacity()" to know the full
capacity of the edge, that is, the real maximum number of tracks that
can go through the associated side.
* Change: In Katana/BloatProfile/Slice::tagsOverloaded(), bloating policy
change, now bloat all the instances under the GCell, not only the first
one.
* Change: In KatanaEngine::runGlobalRouter(), restore the search halo growth
policy to expanding of 3 GCells every 3 iterations.
New metrics displayed, the edge wire length length overload.
* Change: In cumulus/plugins/ConductorPlugin.py, now accepts the following
configuration parameters:
- "anabatic.globalIterationsEstimate", maximum number of global
iterations during the bloating computation passes.
- "conductor.useFixedAbHeight", tells wether the additionnal blank
space must be added so the aspect ratio is kept or the height is
kept (and the block become wider).
Disable the display of "rubber" to unclutter a little the view.
* Bug: In Katana::BloatProfile::FlatInstance for X & Y calculation of
flattened instances reserse the order of transformation. We must apply
the occurrence path transformation to the instance transformation,
and not the other way around.
Was causing the bug in SNX example.
* Bug: In Katana::BloatProfile::Slice::tagOverloadeds(), the underlying
Gcell was not kept in synch with the instance. This was causing a right
shift of the bloated area.
* New: In Katana::BloatProfile, add the selection of overloaded edges and
failed nets.
Add a flag to KatanaEngine::runGlobalrouter() to choose what failed/
overloaded components to display (selectors).
This commit contains two set of features that should have been commited
separately.
1. Compliance with clang 5.0.1, tested with the RedHat collection
llvm-toolset-7. This allow Coriolis to be compiled under Darwin (MacOS)
with Xcode & macports. The bootstrap install system has been modificated
accordingly.
2. The basic support for routing density driven placement. Related
features are:
* Bloat property. Each Occurrence of an Instance can be individually
bloated. This property not attached to any tool to allow the placer and
router to share it as wanted. Nevertheless, it is defined in Etesian.
* BloatProfile in Katana, add individual Bloat properties to Instances
occurrences based on the East & North overflowed edges of each GCell.
* Support in ToolEngine for a "pass number" of a tool. This pass number
is mainly used to make "per pass" measurements. The MeasureSet system
is improved accordingly to support multiple values of a same measure.
* Embryo of "P&R Conductor" to perform the place & route loop until the
design is successfully placed. May be the first brick of a Silicon
Compiler.
* Change: In boostrap/FindBoostrap.cmake, in setup_boost(), added tag to
the python component for macport (ex: python27).
* Change: In boostrap/build.conf, put etesian before anabatic for
instance occurrence BloatProperty dependency.
Added option support for the "llvm-toolset-7" collection to build
against clang 5.0.1.
* Bug: In Hurricane::getRecord( const pair<T,U>& ), the getSlot<> templates
for first & second arguments must be called with <const T> and <const U>
as the pair itself is const (and not simply <T> & <U>).
* Change: In Hurricane::getSlot() temlate, only use "string" arguments and
not const string&, simpler for template argument deduction.
* Bug: In Hurricane::AnalogCellExtension, the StandardPrivateProperty<>
template has a static member "_name". Clang did show that the template
for this static number has to be put inside the namespace where the
template *is defined* (i.e. Hurricane) instead of the namespace where
it is instanciated (i.e. Analog).
* Bug: In Isobar, Matrix_FromListOfList(), PyInt_AsPlacementStatus() must
be put outside the C linkage back in the Isobar C++ namespace (clang).
* Bug: In Hurricane::DBo::~DBo, and derived add a throw() specification
(clang).
* Bug: In Hurricane::RegularLayer::getEnclosure() & setEnclosure(), change
signature so it matches the one of the base class (clang).
* Bug: In Hurricane::CellPrinter, use double brackets for initializer list
(clang).
* Change: In Hurricane::Breakpoint, reverse the meaning of the error level.
Only error level *lesser or equal* than the stop level will be enabled.
* Bug: In CRL/python/helpers/__init__.loadUserSettings(), must put the
current working directory in the sys.path as in certain configuration
it may not be included.
* Bug: In CRL::ApDriver, DumpSegments(), no longer generate segments when
encountering a RoutingPad on a top-level Pin Occurrence. The segment
was generated in the wrong direction, creating DRC violations on the
"mips_core_flat" example.
* Change: In CRL::Measures, partial re-design of the measurements management.
Now, each kind of measure can accept multiple values put in a vector.
The index is intented to match a tool run number.
* Change: In CRL::Histogram, add support for multiple sets of datas,
indexeds with tool run number.
* Change: In CRL::ToolEngine, add support for multiple pass number, add
addMeasure<> templates for the various data-types.
* Change: In CRL::gdsDriver & CRL::gdsParser(), comment out unused GDS record
name constants.
* New: Etesian::BloatProperty, property to attach to Instance occurrences
that contains the extra number of pitch to add to the cell width.
* Bug: In AutoSegment::CompareByDepthLength, the segment length comparison
was wrong, it was always returning true, which broke the "strick weak
ordering" of the comparison.
This was producing a core-dump in GCell::updateDensity() when sorting
a vector<>. The end() iterator was being dereferenced, leading to the
problem.
* Bug: In Katana::DataSymmetric::checkPairing(), the test for segments
whose axis is perpandicular to the symmetry axis was wrong
("!=" instead of "-").
* New: In Katana/GlobalRoute, new ::selectSegments(), selectOverloadedgcells()
and selectBloatedInstances() to automatically select segments from
overloaded edges, overloaded GCells and bloated cells.
* Change: In KatanaEngine, return a more detailed success state, distinguish
between global and detailed.
Add support for multiple routing iterations.
* New: In cumulus/python/plugins/ConductorPlugin.py, embryo of routing
driven placement.
* Change: In Hurricane::Isobar/PyHurricane.h, make the hash function use
the DBo id whenever possible instead of the object pointer, fall back
to it for standalone objects (Box like one). The DirectHashMethod()
macro generate a C style function (linkage) which call a template
function "getPyHash<>()" that uses a SFINAE mechanism to select
the right variant.
Create two comparison macros DirectCmpByPtrMethod() and
DirectCmpByValueMethod() to customize the comparison for objects that
have C++ operator==(). So now two boxes with the same contents will
be seen equal by Python. For DBo objects we keep the previous
comparison by C++ pointer.
* Change: In CRL::RoutingLayerGauge::getHorizontalGauge(), when selecting
the default gauge, try, if possible to avoid the PinOnly one.
Same goes for the vertical one.
* Bug: In Katana::TrackCost CTOR, symmetric track axis position was wrong,
was using the reference instead of the symmetric.
* Bug: In BoraEngine::updatePlacement(), set up the Dijkstra search halo
to one pitch so it can use immediately neighboring channels.
* New: In BoraEngine, added python startup hook like in Katana. Mainly
to setup debug nets.
* New: In bootstrap/coriolisEnv.py, add the "etc" directory to the
PYTHONPATH as initialization are now Python modules.
* New: In Hurricane/analogic, first groundwork for the integration of
PIP/MIM/MOM multi-capacitors. Add C++ and Python interface for the
allocation matrix and the list of capacities values.
* Change: In Hurricane::RegularLayer, add a layer parameter to the
constructor so the association between the RegularLayer and it's
BasicLayer can readily be done.
* Change: In Hurricane::Layer, add a new getCut() accessor to get the
cut layer in ViaLayer.
* Change: In Hurricane::DataBase::get(), the Python wrapper should no
longer consider an error if the data-base has not been created yet.
Just return None.
* Bug: In Isobar::PyLayer::getEnclosure() wrapper, if the overall
enclosure is requested, pass the right parameter to the C++ function.
* Change: In AllianceFramework, make public _bindLibraries() and export
it to the Python interface.
* Change: In AllianceFramework::create(), do not longer call bindLibraries().
This now must be done explicitely and afterwards.
* Change: In AllianceFramework::createLibrary() and
Environement::addSYSTEM_LIBRARY(), minor bug corrections that I don't
recall.
* Change: In SearchPath::prepend(), set the selected index to zero and
return it.
* Change: In CRL::System CTOR, add "etc" to the PYTHONPATH as the
configuration files are now organized as Python modules.
* New: In PyCRL, export the CRL::System singleton, it's creation is no
longer triggered by the one of AllianceFramework.
* New: In CRL/etc/, convert most of the configuration files into the
Python module format. For now, keep the old ".conf", but that are no
longer used.
For the real technologies, we cannot keep the directory name as
"180" or "45" as it not allowed by Python syntax, so we create "node180"
or "node45" instead.
Most of the helpers and coriolisInit.py are no longer used now.
To be removed in future commits after being sure that everything
works...
* Bug: In AutoSegment::makeDogleg(AutoContact*), the layer of the contacts
where badly computed when one end of the original segment was attached
to a non-preferred direction segment (mostly on terminal contacts).
Now use the new AutoContact::updateLayer() method.
* Bug: In Dijkstra::load(), limit symetric search area only if the net
is a symmetric one !
* Change: In Katana/python/katanaInit.py, comply with the new initialisation
scheme.
* Change: In Unicorn/cgt.py, comply to the new inititalization scheme.
* Change: In cumulus various Python scripts remove the call to
helpers.staticInitialization() as they are not needed now (we run in
only *one* interpreter, so we correctly share all init).
In plugins/__init__.py, read the new NDA directory variable.
* Bug: In cumulus/plugins/Chip.doCoronafloorplan(), self.railsNb was not
correctly managed when there was no clock.
* Change: In cumulus/plugins/Configuration.coronaContactArray(), compute
the viaPitch from the technology instead of the hard-coded 4.0 lambdas.
In Configuration.loadConfiguration(), read the "ioring.py" from
the new user's settings module.
* Bug: In stratus.dpgen_ADSB2F, gives coordinates translated into DbU to
the XY functions.
In st_model.Save(), use the VstUseConcat flag to get correct VST files.
In st_net.hur_net(), when a net is POWER/GROUND or CLOCK also make it
global.
* Change: In Oroshi/python/WIP_Transistor.py, encapsulate the generator
inside a try/except block to get prettier error (and stop at the first).
* Bug: In Katana::SegmentFsm CTOR, when computing costs for METAL2 in
non-preferred direction attached to METAL1 terminals, do not try to
align on a METAL3 track, as there may be not. Especially when the
METAL3 pitch is not multiple of the METAL1 one.
Compute at least one cost (with the same axis as the vertical METAL1
terminal).
* Change: In Etesian::BloatCells, adjust the "90%" bloat profile for a
METAL3 pitch of 8 lambdas (sligh decrease).
* Bug: In cumulus/plugins/ChipPLace.py, import chip.Chip, not only chip.
* Bug: In CRL::cstDriver(), re-activate the management of the VstUseConcat
flag. Why was he removed in the first place?
* Change: In KatanaEngine::runGlobalRouter(), no longer give the details of
each overflowed edge and the complete list of impacted nets.
Only a count.
* Change: In Anabatic::GCell::updateDensity(), all non-passthrough wires
now have a cost of 0.5 instead of 0.33 for locals.
* Change: In Manipulator::canMoveUp(), increase the "reserve" amount to
1.0 for "far from terminal" wires (rpDistance > 2).
* Change: In NegociateWindow::NegociateOverlapCost(), always sets "AtRipupLimit"
when the overlapping segment is nearing it's maximum ripup limit.
(different detection for non-preferred and regular)
* Change: In SegmentFsm::_slackenStrap(), call avoidBlockage() if it is
overlapping a blockage *or* a segment at it's ripup limit. I hope I
didn't create an infinite loop here.
* Bug: In cumulus/plugins/PadsCorona.py, CoreWire._computeCoreLayers(),
the big contact between symbolic and real was badly computed for
east/west (was using width instead of height, bummer!).
In Corona._createCoreWire(), completly screwed computation of the
side gap, was using a badly initialized value of the "bb" variable.
* Bug: In cumulus/plugins/Chip.py, the computation of the minimal size
for the corona was wrong, do *not* add the size of the pads and
multiply by two as it is done by "inflate". This was forcing the user
to create way to large chips for a given core size.
This commit degrades the run success rate of ARMv2a to 87% (40 iters).
* New: In CRLcore/etc/.../kite.conf, add configuration parameters:
katana.termSatReservedlocal
katana.termSatthreshold
for the new edge capacity computation system.
* New: In CRLcore/etc/symbolic/phenitec06/, add support for N. Shimizu
small I/O pads (supplied in phlib80). Tune various parameters of
Anabatic/Katana to increase routing success.
* Change: In CRLcore/alliance/ap/ApParser, make Pin external components,
so RoutingPad will be build upon in global routing.
Do not complain when a I/O pad has a physical instance that did
not exists in the netlist. Just create it (appeared in phlib80).
When no netlist instance exists in a pad, the pad Cell is still
considered as terminal.
* New: In Etesian::BloatCells, new profile named "3metals" better suited
for two routing metals technologies (i.e. Phenitec).
* New: In Anabatic::RawGCellsUnder, new CTOR which take only source &
target points instead of a segment. Needed to manage wide segment for
which the axis to consider is not that of the segment (one axis for
each track it intersect).
* New: In Anabatic::GCell, add a RoutingPad count attribute, for Edge
reservation computation.
* New: In AnabaticEngine::computeEdgeCapacities(), instead of decreasing
all edges of a fixed amount (hTrackReservedLocal), guess the GCell
cluttering from the number of RoutingPads that it contains.
For non-saturated GCells, the four edges are decreased by the number
of RoutingPads. We use the maximum from the two neigboring GCells.
The hTrackReservedLocal parameter is now used only as a *maximum*
that the edge reservation can reach.
If a GCell is saturated (more than 8 RoutingPads, the saturation is
propagated horizontally to 2 neigboring GCells).
* Change: In AutoContactTerminal::getNativeConstraintBox(), use a more
flexible gauge name matching for terminal vertical extensions correction.
Namely, match all "msxlib*" kind of gauges.
* Change: In AutoSegment::setAxis(), add the ability to force the axis
position, even if it is a non-canonical segment. Maybe needed in the
initialisation steo, before the first canonisation is performed.
* New: In NetBuilder, added new methods _do_1G_1PinM1() and _do_2G_1PinM1(),
to manage coronas for Phenitec designs.
To avoid various side effects from segments being too close from
the north / east side of the routing area, make those segments fixeds.
* Change: In KatanaEngine::annotateGlobalGraph(), the management of wide
wires was wrong. The axis to use to find the underlying GCells is the
one of the track, not of the segment. This was creating bad edge
capacity computation under the power ring of a block and subsequently
routing failures.
* New: In Kanata::Manipulator, added method reprocessParallels(), not used
though, but keep it anyway, might be of use later...
* New: In Kanata::Manipulator, added method avoidBlockage() for terminal
METAL2 in non-preferred direction, restrict the terminal and turn
constraint box at the current position of the perpandicular, so it
doesn't create a deadlock in METAL2.
* Change: In SegmentFsm::conflictSolveByPlaceds(), if we cannot break
using the whole overlap, try the first atomic overlap.
* New: In SegmentFsm::_slackenStrap(), manage conflict between a non-prefered
segment and a blockage, this when to call avoidBlockage()...
* New: In Katana::Configuration, management of the new edge computation
parameters:
katana.termSatReservedlocal
katana.termSatthreshold
* New: In Cumulus/plugins/Core2Chip, support for Phenitec I/O pads.
* Change: In Katana::SegmentFsm::_slackenStrap(), make unbreakable segments
pass through the LocalVsGlobal state so when other try to ripup them
they are prioritary. Otherwise some could go through Unimplemented
directly, without allowing other to attempt to make a detour.
* Change: In Katana::NegociateWindow::NegociateOverlapCost(), when a
global, which is about to be slackened wants to use a track where there
is a segment directly connected to a terminal with a significant
ripup count, mark it as "AtRipupLimit" so it tries to avoid it.
The idea is that globals with high ripup count must avoid terminal
segments because it is likely they will be riped up again so they
better find another track. This was leading to unsolvable configuration
when two segments always want the same track. In this cas, the global
would loose.
* Bug: In Katana::TrackSegment::canSlacken(), never slacken a segments in
non-preferred direction.
* Change: In Anabatic::AutoHorizontal::_slacken(), allow slackening of
segments which perpandiculars are in non-preferred direction, and
not only directly attached to terminals.
* Change: In Anabatic::AutoSegment::canMoveUp(), re-allow segments which
perpandiculars are in non-preferred direction to be moved up.
* Bug: In Katana::Manipulator::moveUp(), when moving up, do not forget
to ripup and reschedule said segment.
This non-deterministic behavior was showing only in the ARMv2a benchmark
around event 180k...
* Bug: In Anabatic::Session::_netInvalidateds & _netRevalidateds, the
set<> was still sorted on pointers. As contacts & segments can be
created to maintain connexity after a layer change, we got a
discrepency in objects Ids that may generate a change in ordering
later.
* Bug: In Katana::Session::_doRemovalEvents(), the set of Tracks that
got elements deleted was still using pointers. Now we use a TrackSet
sorted on (direction,depth,axis). This should not have created
a change in the results, as destructions do not change Ids, but it
genereate extra differences in traces.
* Change: In Hurricane::Cell_LeafInstanceOccurrences, add the ability to
walkthrough the leaf of one specific top-level instance.
* Change: In Hurricane::Cell_NonLeafInstanceOccurrences, add the ability to
walkthrough the leaf of one specific top-level instance.
* Change: In Hurricane::Cell:
getLeafInstanceOccurrences() and getNonLeafInstanceOccurrences(), now
have a parameter Instance* to select the leafs we want to walk through.
If set NULL (default value) browse through all the instances,
as before.
* Change: In Hurricane::DeepNet, add forgotten Inspector support.
* New: In EtesianEngine, add a "block" (and Instance) attribute to allow
the placement of one specific bloc. If we want to place the core of
a chip and take into account the external terminals (if they are not
already fixed as Pins at the edge of *said* block). We must place
the core *in the context* of it's instanciation in the corona.
Note for G. Gouvine : Pin & external RP should be taken into account
starting at line 629 of EtesianEngine.cpp...
* New: In cumulus/plugins/chip/Chip.py, make use of the new block
placement feature of ETesian.
* Bug: In KatanaEngine::create(), perform a pre-check to prevent trying to
route whole chip, which is forbidden an leads to annoying core-dumps.
Routing must take place "at most" at Corona level.
* Bug: In KatanaEngine::PowerRails, create a plane for METAL1 blockage.
Not completely sure this was a bug...
* Change: In Hurricane::SharedName, replace the incremental Id by a hash key.
This is to ensure better deterministic properties. Between use cases,
additional strings may have to be allocated, shitfing the ids. Even if
hash can be duplicated, we should be able to ensure that the absolute
order in map table should be preserved. Supplemental strings are inserted
in a way that keep the previous order.
* Change: In CRL/etc/symbolic/cmos/kite.conf, add "katabatic.routingGauge"
default parameter value ("sxlib").
* Change: In CRL/etc/common/technology.conf, define minimal spacing for
symbolic layers too (added for METAL4 only for now).
* Change: In CRL::Histogram, extend support to dynamically sized histograms.
Add a text pretty print with table and pseudo-curve.
* Change: In Cumulus/plugins/ClockTreePlugin, create blockage under the
block corona corners so the global router do not draw wire under them.
This was creating deadlock for the detailed router.
When the abutment has to be computed, directly use Etesian to do it
instead of duplicating the computation in the Python plugin.
* New: In Etesian, as Coloquinte seems reluctant to evenly spread the
standard cells, we trick it by making them bigger during the placement
stage. Furthermore, we do not not uniformely increase the size of the
cells but create a "bloating profile" based on cell size, cell name
or it's density of terminals. Currently only two profiles are defined,
"disabled" which does nothing and "nsxlib" targeted on 4 metal layer
technologies (aka AMS 350nm, c35b4).
* Bug: In Knik::MatrixVertex, load the default routing gauge using the
configuration parameter "katabatic.routingGauge" as the default one
may not be the first registered one.
* New: In AnabaticEngine::setupNetDatas(), build a dynamic historgram of
the nets terminal numbers.
* Bug: In Anabatic::AutoContact::Invalidate(), always invalidate the
contact cache when topology is invalidated. In case of multiple
invalidations, if the first did not invalidate the cache, later one
that may need it where not allowed to do so. The end result was correct
nonetheless, but it did generate annoying error messages.
* Bug: In Anabatic::AutoContactTurn::updateTopology(), bad computation
of the contact's depth when delta == 2.
* Bug: In Anabatic::Gcell::getCapacity(), was always returning the west
edge capacity, even for the westermost GCell, should be the east
edge in that case.
* New: In Anabatic::AutoSegment, introduce a new measure "distance to
terminal". This is the minimal number of segments separating the
current one from the nearest RoutingPad. This replace the previous
"strong terminal" and "weak terminal" flags.
This distance is used by Katana to sort the events, we route the
segments *from* the RoutingPads *outward*. The idea being that if we
cannot event connect to the RoutingPad, there is no points continuing
as thoses segments are the more constraineds. This gives an order close
to the simple ascending metals but with better results.
* New: In Anabatic::AutoSegment, introduce a new flag "Unbreakable", disable
dogleg making on those segments. mainly intended for local segments
directly connecteds to RoutingPads (distance == 0).
* New: In Anabatic::AutoSegment, more aggressive reducing of segments.
Now the only case where a segment cannot be reduced is when it is
one horizontal branch in a HTee or a vertical on a VTee. Check if,
when not accounted the source & target VIAs are still connex, if so,
allow reducing.
* New: In Anabatic::AutoContact, new state flags CntVDogleg & CntHDogleg
mainly to prevent making doglegs twice on a turn contact. This is to
limit over-fragmentation. If one dogleg doesn't solve the problem,
making a second one will make things worse only...
* Bug: In Anabatic::Configuration::selectRpcomponent(), we were choosing
the component with the *smallest* span instead of the *bigger* one.
* New: In Anabatic::GCell, introduce a new flag "GoStraight" to tell that
no turn go be made inside those GCells. Mainly used underneath a block
corona.
* New: In AnabaticEngine::layerAssign(), new GCellRps & RpsInRow to manage
GCells with too many terminals. Slacken at least one RoutingPad access
when there is more than 8 RoutingPad in the GCell (slacken or change
a vertical METAL2 (non-preferred) into a METAL3).
* Change: In Anabatic::NetBuilderHV, allow the use of terminal connection
in non-preferred direction. That is, vertical METAL2 directly connected
to the RoutingPad (then a horizontal METAL2). This alllows for short
dogleg without clutering the METAL3 layer (critical for AMS c35b4).
Done in NetBuilderHV::doRp_Access(), with a new UseNonPref flag.
Perform some other tweaking on METAL1 access topologies, to also
minimize METAL3 use.
* New: In AnabaticEngine::computeNetConstraints(), also compute the
distance to RoutingPad for segments. Set the Unbreakable flag, based
on the distance and segment length (local, short global or long global).
New local function "propagateDistanceFromRp()".
* Change: In AnabaticEngine.h, the sorting class for NetData, SparsityOrder,
is modificated so net with a degree superior to 10 are sorted first,
whatever their sparsity. This is to work in tandem with GlobalRouting.
* New: In Katana::TrackSegmentNonPref, introduce a class to manage segment
in non-preferred routing direction. Mostly intended for small METAL2
vertical directly connected to RoutingPad. Modifications to manage
this new variant all through Katana.
* Change: In Katana::GlobalRoute, DigitalDistance honor the GoStraight flag
of the GCell. Do not make bend inside thoses GCells.
* Change: In KatanaEngine::runGlobalRouter(), high degree nets (>= 10) are
routed first and whitout the global routing estimation. There should be
few of them so they wont create saturations and we want them as straight
as possible. Detour are for long be-points.
Set the saerch halo to one GCell in the initial routing stage (before
ripup).
* Bug: In KatanaEngine & NegociateWindow, call _computeCagedconstraints()
inside NegociateWindow::run(), as segments are inserted into tracks
only at that point so we cannot make the computation earlier.
* Change: In Katana::Manipulator::repackPerpandiculars(), add a flag to
select whether to replace the perpandiculars *after* or *before* the
current segment.
* Change: In Katana::NegociateWindow::NegociateOverlapCost(), when the
segment is fully enclosed inside a global, the longest overlap cost
is set to the shortest global hoverhang (before or after).
When the cost is for a global, set an infinite cost if the overlapping
segment has a RP distance less or equal to 1 (this is an access segment).
* Bug: In Katana::PowerRailsPlane::Rail::doLayout(), correct computation of
the segments extension cap.
* New: In Katana::QueryPowerRails::addToPowerRail(), add support for Pad.
* Change: In Katana/PreProcess::protectCagedTerminals(), apply the contraints
to any turn connected to the first segment of the RoutingPad so the
perpandicular constraints got propagated to the perpandicular segment...
* Change: In RoutingEvent, cache the "distance to RP" value.
* Change: In RoutingEvent::Key::compare(), sort *first* on distance to
RoutingPad, then layer depth. If both distance to RoutingPad is null,
then sort on segment length.
* Change: In RoutingEvent::_processRepair(), try a repack perpandicular with
perpandiculars first (then with perpandicular last, then give up).
* Change: In SegmentFsm::bindToTrack() and moveToTrack(), set an axis hint
when creating the insertion event.
* Change: In SegmentFsm::_slackenStrap(), add a step through slacken between
minimize and maximum slack (wihch directly end up in unimplemented).
* Change: In Session::_addInsertEvent(), add an axis parameter needed when
the axis of the segment is not the one of the track (case of wide
segments or non-preferred direction).
* Bug: In Track::_preDestroy(), bad management of the TrackElement reference
count. Destroy the segment only when reaching zero...
* Bug: In Track::expandFreeIneterval(), forgotten to manage case when there
is a set of overlaping segments at the "end" of the track, the
EndIsTrackMax was not set.
* Change: In TrackCost::Compare, increase the cost when an overlaping
segment is at it's ripup limit. We should try *not* to rip it up if
we can. Add a dedicated flag "AtRipupLimit".
* Change: In TrackElement, add proxies for isUnbreakable(), new function
updateTrackSpan().
* New: In TrackFixedSegment CTOR, when a supply wire of METAL2 or above is
found, make the underlying GCells "GoStraight".
* New: In TrackElement::canDogleg(GCell*), check for already done perpandicular
dogleg on source/target (reject if so).
* Change: In Hurricane::Error constructors disable the backtrace generation.
(*very* slow).
* Change: In Hurricane::Library::getHierarchicalname(), more compact
naming. Remove the name of the root library.
* New: In Hurricane::Net, new type "FUSED", for component with no net.
More efficient than having one net for each.
* Change: In CellViewer, BreakpointWidget, use Angry Birds icons.
* Change: In CellWidget::State, use the hierarchical name (cached) as key
to the state. This allow to load two cells with the same name but from
different libraries in the widget history.
* Change: In PyGraphics, export "isEnabled()" and "isHighDpi()" functions.
* Change: In CRL/etc/symbolic/cmos/plugin.conf, and
CRL/etc/common/plugin.conf use the physical dimensions converters.
* Change: In CRL/etc/symbolic/cmos/technology.conf, make the GDS layer
table coherent with the default Alliance cmos.rds.
* New: CRL/python/helpers/io.py, put ErrorMessage new implementation here,
along with a new ErrorWidget written in PyQt4. It seems finally that
PyQt4 can be used alongside Coriolis Qt widgets.
New ErrorMessage.catch() static function to manage all exceptions
in except clauses.
* Change: In CRL/python/helpers/, no longer use ErrorMessage.wrapPrint(),
directly print it.
Rewrite the utilities to display Python stack traces "textStacktrace()"
and "showStacktrace()".
* Change: In CRL::AllianceFramework, shorten the names of the libraries.
* Change: In CRL::ApParser & CRL::ApDriver, more accurate translation between
Alliance connectors (C record) and Hurricane::Pin objects. Pin are no
longer made square but thin and oriented in the connecting direction.
Use the new fused net for unnamed components.
* New: In CRL::GdsParser, implementation of SREF parsing, i.e. instances.
Due to the unordered nature of the GDS stream, instances creation are
delayed until the whole stream has been parsed and only then are they
created.
For the sake of reading back Alliance s2r GDS, we assume that any
TEXT following a boundary is the Net name the boundary (component)
belongs to.
Create abutment box for Cells, computed from the bounding box, so
the Hurricane QuadTree could work properly.
Make use of the fused net for unnamed components.
* New: In Cumulus/plugins/chip, complete rewrite of the I/O pad management.
Now we can mix real (foundry) pads and a symbolic core.
To cleanly support the de-coupling between the real part and the
symbolic one we introduce a new intermediary hierarchical level, the
corona. We have now:
Chip --> Pads + Corona --> Core.
At chip level (and if we are using real pads) the layout is fully
real (excepting the corona).
The Corona contains everything that is symbolic. It has symbolic
wires extending outward the abutment box to make contact with the
real wires coming from the pads.
In the pad ring we can use corners instances (or not), pad spacers
or directly draw wires between connectors ring pads.
Provide two flavors: placement only or full place & route.
WARNING: If routing in a second step, *do not route* the *Chip* but
the *Corona*.
* Change: In Cumulus/plugins/clocktree, give the modified Cell an
additional extension of "_cts" (Clock Tree Synthesis) instead of
"_clocked", to follow the common convention.
* New: In cumulus/plugins/S2R.py, encapsulate call to Alliance S2R and
reload the translated Cell in the editor.
* New: In cumulus/plugins/core2chip, provide an utility to automatically
create a chip from a core. To work this plugins must have a basic
understanding of the pad functionalities which may differs from
foundry to foundry. So a base class CoreToChip is created, then for
each supported pad foundry a derived class is added. Currently we
support AMS c35b4 and Alliance symbolic cmos.
* Bug: In Anabatic::Configuration, read the right configuration parameter
"anabatic.topRoutinglayer" (Katana), and not the one for Katabatic...
* Change: In Unicorn/cgt.py, process the plugins in alphabetical order
to ensure a reproductible ordering of the menus...
* Change: In Hurricane::CellViewer, reorganisation of the to level menus.
Add "Misc." and it's two sub-menus "Beta" and "Obsolete".
* Change: In GraphicKiteEngine::addToMenu(), set Kite in the obsolete menu.
* Change: In GraphicKatanaEngine::addToMenu(), set Katana as the standart
router.
* Bug: In CRL/etc/symbolic/cmos/plugins.conf, rails dimensions are no
longer expressed directly in lambda. Must be created using helper.l().
* Change: In CRL::ApParser, slightly more smart management of Pin width.
Must normalize Pin behavior between Alliance & Hurricane as in
Alliance they have only one dimension.
* Change: In CRL::LefImport, if a net name end with "!", assume it's a
global one. Have to check this naming convention.
* Change: In Anabatic::NetBuilderHV::_do_1G_1PinM3() & _do_1G_1PinM2()
now implemented. Needed for the corona routing support.
* Change: In AnabaticEngine::setupPreRouted(), exclude segments outside
the abutment box.
* Change: In KatanaEngine::PowerRails, remove the I/O pad support as now
we route only inside the Corona. So only one vdd/vss/ck are supported.
* New: In cumulus/plugins/ChipPlugin.py, complete rewrite of the chip
support:
* Uncouple pad I/O ring whith real cells (foundry) from a symbolic
core. A new intermediate level "corona" is introduced to handle
the real/symbolic transition.
* Ability to explicitly setup position of the pads on the chip side
in case of uneven distribution.
* Enable clock tree to be build with 3 metal only (M2 to M4) instead
of (M2 to M5).
* New: In Hurricane::Isobar::PySegment, added wrapper for getOppositeAnchor().
* Bug: CRL::PyRoutingLayerGauge, Python wrapper of getTrackPosition() was
in fact returning getTrackNumer().
* Bug: In Katana::PowerRailsPlanes::Rail::doLayout(), add the half minimum
distance to the blockage segments extensions. Was causing too near
VIAs is cmos45.
* Change: In cumulus/plugins/ClockTree, correctly manage routing gauge when
the lower pitches (M2/M3) is different from the upper one (M4/M5).
But we still can only do sxlib compliant gauges because we do not
handle a switch in preferred routing directions.
* Bug: In Katana::Track::expandFreeInterval(), the OutsideElement case was
not handled correctly, the end index must be increased in that case.
As a result, this function was returning too short an interval.
This was affecting the computation of perpandicular free interval
in DataNegociate::update() for perpandicular fixed but not in a track.
* New: In Anabatic::NetBuilder and NetBuilderVH, now manage GCells with
one Pin, and up to three globals. Used to put terminals at the
edge of a block.
* New: In EtesianEngine, now manage placed Pins.
(done through extractInstanceName())
* Change: In CRL::RoutingGauge::getHorizontalGauge() no longer skip PinOnly
gauges to find the reference one (same goes for vertical).
* In Katana::RoutingEvent::_processRepair(), do no reschedule perpandiculars
that are already in repair mode, they may loop with repackperpandiculars().
* Bug: In Anabatic::Edge::getDistance(), remove the additionnal 0.1
added to horizontal edges. This was for testing before the hScaling
parameter was added (to the distance computation in GlobalRoute).
* New: Anabatic::Path_Edges, collectio to walkthrough all the edges
between two node. More complex than in Knik as we are no longer
using a regular grid. We may request the north bound path or south
bound path.
Collection returned by AnabaticEngine::getEdgesUnderPath().
* New: In Anabatic::NetData, add a new flag GlobalEstimated to tell if
the net RMST has been computed (using FLUTE).
* New: In Anabatic::PriorityQueue, used to sort Vertexes by increasing
distances, add a new criterion to be used in case of distance
equality. The attractor which should be the center of the search
area. In case of equality, we choose the Vertex which is closest
to the attractor. Give a small improvement, and more "dendritic"
trees.
For a more simple implementation of the comparison function it is
made as a static member (so no two Dijkstra objects at the same
time...).
* Change: In Anabatic::Edge, make the estimate occupance a floating
point number instead of an integer.
* New: In Katana::GlobalRoute, finally implement the estimated congestion
driven router. Net RMST estimated using FLUTE.
Use the historic cost from Knik implementation and not the one
given in Damien's thesis, which seems not be the same and a bit
strange.
* New: In KatanaEngine, add the ability to exclude nets from routing,
and export it to Python.
* Change: In Hurricane::CellWidget, new "isPrinter" attribute to know if
the CellWidget is used as a device for printing.
New function copyExtensionsGos() to duplicate the ExtensionGo drawing
callbacks. This is a temporary hack until the ExtensionGo are made static
to be shared by all CellWidgets.
In _redraw(), the DrawingQuery flags were not correctly reset between
different stage of the drawing. This was resulting of uneeded walkthough
of the slicing tree, along with incorrect display of some of the layers
(i.e. rubbers where diplayeds when ExtensionGos where active).
* Change: In GraphicKatanaEngine, fine tune the display of GCells for printing
CellWidget.
* Change: In Hurricane::CellPrinter, copy all the settings from the palette
of the reference (graphic) CellWidget into the printer CellWidget.
Also copy the ExtensionGos callbacks so we can print them. Use the
new CellWidget attribute "isPrinter" for the callbacks to be able
to adapt to Printer settings.
* Change: In Hurricane::Time::getStringTime(), only print two decimals
for time durations.
* Change: To allow multiple tools, and not only Knik, to link and use
FLUTE, remove it from Knik and put it at top level.
Bootsrap must compile this new tool and the library must be
included in all CMakeLists.txt depending on Knik (and soon
Anabatic).
The short net mode degrade the routing in some cases. This will be
fixed in a next batch of commits.
* New: In Hurricane::NetRoutingProperty, added "ShortNet" flag for Nets
that are completly inside *one* GCell.
* Bug: In CRL::BlifParser::Model::staticInit(), when looking for the
output of zero and one cell, also skip the blockage net (as well as
automatic and supplies).
* New: In Anabatic::AutoSegment, added "ShortNet" flag to know if the
segment is part of a short net (fully included in *one* GCell).
Also add accessor/mutators for the _analogMode flag (was it ever
used before?).
* New: In Anabatic::NetBuilder::singleGCell(), if a RoutingPad is
vertically small, add a vertical segment to give it some slack.
* New: In Anabatic::Dijkstra::_materialize(), detect "short net" as
they have only one GCell in their source list...
* Bug: In AnabaticEngine::_loadGrbyNet(), reset the AutoSegment
"short net" and "analog mode" creation flags between two different
nets.
* New: In Katana::Configuration, added dedicated ripup for short net
segmnts.
* New: In Katana: partially implemented support for "short dogleg", that
is dogleg that are always kept in same metal because they connect
neighboring perpandicular tracks. Not finished neither activated
yet.
* New: In Katana::TreckElement and derived, export the the *short net*
support from AutoSegment.
* Bug: In Katana::RoutingEvent::_processRepair(), when a segment is
successfully inserted, re-process any perpandicular that is in
repair state, as it may have a new chance to be placed.
* New: In Katana::SegmentFsm::slackenTopology(), always reject short nets.
* Bug: In Katana::Track::check(), correctly handle wide segments instead
of issuing false check messages.
* New: In Anabatic::LayerAssign, a new mode "LayerAssignNoGlobalM2V" has
been added to manage the 3 routing metal technologies like AMS 350nm.
The standard cells have all their connectors punctual and aligned on
an horizontal line in the middle of the Cell. This is a design
inherited from the channel routing times that makes global routing
in metal2 *through* a standard cell almost impossible (except for
directly neighboring cells). Thus, the layer assignment must move
up all the metal2 that span more than two GCells.
* Change: In Katana::Manipulator::ripupPerpandiculars(), when a perpandicular
has a fixed axis and it's (sole) underlying track is taken, ripup
the other segment to ensure the perpandicular interval will be free.
We need to do that, because in DataNegociate::update(), if the
perpandicular is taken, the perpandicular interval will always been
empty preventing the segment to have a valid track span (so directly
failing).
* Change: In Katana::SegmentFsm::conflictSolveByPlaceds() the fixed axis
segments must also been taken into account as conflicts.
Also correct a small bug, the first conflicting segment in the
interval was not taken into account correctly.
* Change: In all tools supplying documentation, as we use some specific
software to create the doc, they may not be available, or worse, be
and incompatible version. So, by default, we install the files shipped
with the git repository. To force a full doc rebuild, use the "--doc"
flag of ccb.py.
* Change: In Anabatic::setupPreRouteds(), routed DeepNets can have
components both at Occurrence root net devel and at top level.
If no nets remains to route, set the tool state to EngineDriving,
which prevent any further work (except for finalize).
* Bug: In Anabatic::Dijkstra, the degree of a vertex (the number of neighbors
belonging to the same net) was miscalculated. This was leading, in the
materialize step to some feed-through vertexes not being broken.
Leading in turn to incomplete transformation of the detailed routing.
Also in _trackback(), the degree of the first vertex we were backtracking
from was not incremented.
* Bug: In Anabatic::Dijkstra::materialize(), systematically use
GCell::breakGoThrough() on both source and target. This is needed when
we are in the ripup phase as both source and target can be go-through.
This was also leading to incomplete detailed routing transformation.
* Change: In Anabatic::Edge::ripup(), ripup one third of the segments instead
of thoses exeeding the global length threshold. This way we are sure to
desaturate an edge. Needs to be further calibrated.
* Change: In Aanabatic::GCell::breakGoThrough(), no longer return NULL.
Return existing gcontact if any. Break if it is a go-through and create
a new gcontact in last resort. Maybe rename this function.
* New: In Anabatic::Configuration, new parameters:
- anabatic.edgeHScaling, to adjust the length of the horizontal edges
relative to the vertical ones (this is a ratio).
- anabatic.globalIterations, set the maximum number of ripup passes
of the global router.
* New: In CRL/etc/*/kite.conf, added new parameters anabatic.edgeHScaling
and anabatic.globalIterations.
* New: In Katana::GlobalRoute::DigitalDistance, take into account the new
edgeHScaling factor. Must be used when the capacity of V-edges differs
greatly for H-edges (case of AMS 350nm c35b4 for instance).
* Bug: In Katana::GlobalRoute::DigitalDistance, the historic cost is
computed for an edge length of "1". Must be multiplicated by the
current edge length to have any measurable effect.
This bug is finally explaining why the ripup was producing the
same solutions over and over, the historical cost was negligible!
* Change: In Katana::RoutingPlane::getTrackByPosition(), when requesting a
track less than *one pitch* beyond the last one, return the last one
instead of NULL. Only if the mode allows it (i.e. Nearest or Inferior).
* Bug: In Katana::Track::addOverlapCost(), check that the overlap is
not *exactly* zero (exact interval fitting), and do not consider
them as obstacle (they where raising the infinite flag when they
where *fixed*).
* Bug: In Hurricane::Cell::uniquify(), a set<Cell*> sorted on pointers
was remaining. Now sorted on Entity::Id.
* Bug: In CRL::VhdlEntity, in the driver, the components where driven
in pointer order (set<> again). Now use ids.
* Bug: In CRL/etc/scn6m_deep_09/technology.conf, the symbolic extentions
for VIAs and layers were wrong. Have to be multiplied by two.
* Change: In AnabaticEngine, AutoContact and AutoSegment LUTs are now
sorted on Entity::Id. Should not have had any impact, but better
safe than sorry.
* Change: In KatanaEngine, Symmetric contraint map<> is now sorted on
Entity::id. Idem for TrackSegmentLut.
* New: In Hurricane::Entity, add an id counter limit and a memory size
limit. The two limits are checked only when a new Entity object is
created. This should help avoiding massive memory links.
* New: In CRL Core, add a "crlcore.groundName" and a "crlcore.powerName"
parameter to specify the name of the ground/power signals to be
created if they are missing in a Cell. For Alliance libraries it
would be "vss" & "vdd" (default values), but for real technologies,
it is often "gnd!" & "vdd!".
The Blif parser is modificated to make use of it.
* Bug: In AnabaticEngine::unify(), set the resulting unified segment in
the center of the GCells common side. Gcells under a segment are
found by using the edge that cover the segment axis. When we have
a "bend" GCell stack and the axis is wrong, they could be ommited.
This was causing deleted segments to be not removed from some
Edges, then core dump.
* Change: In Anabatic::AutoSegment::create(), smarter choosing of the
reference contact, select the fixed or terminal one instead of
always the source one.
* New: In Anabatic::Edge::isEnding(), new function to check if a
segment going through an Edge is starting/ending in either source
or target GCell of the edge (active only when running in channel
mode).
* New: In Anabatic::Edge::add(), a segment takes part in the occupancy
only if it is not ending in either source or target (channel mode
only). The occupancy due to terminal is pre-computed in Katana.
* New: In Anabatic::Edge::ripup(), in channel mode, never ripup a
segment which is ending in either source or target (we *have* to
access this edge to connect to the terminal).
* Bug: In Anabatic::GCell::hcut() and vcut(), force the update of
the Edge which is on the side that will get splitted by the cut.
It's capacity will be reduced to it must be updated.
* Change: In Anabatic::GCell::updateGContacts() add a flag to conditionnally
update horizontals or verticals only. We may require only a partial
update when resizing the GCell in only one direction.
This, again, related to the fact that we compute the GCells under
a segment thanks to it's axis position, so we need to be very careful
when modificating axis.
* Change: In Katana::Block::resizeChannels(), only update GContact vertical
position. Do not disturb X positions of segments.
* Bug: In Katana::GlobalRoute::DigitalDistance, in channel mode, some
Edges can have a zero capacity, but still be reachable if the net has
a terminal in either source or target. Look for this case and return
a distance of zero instead of "unreachable". This was causing the
global routing not to complete in channel mode.
For computing the edge distance, makes the vertical edges much more
long (10 times) than the horizontal ones as the vertical capacity is
very limited. Hard coded for now, should make it a parameter in the
future.
* Change: In KatanaEngine::annotateGlobalGraph(), decrease the capacity
of edges with reserveCapacity for each terminal inside a GCell.
Both north and south edges are decreased as we a terminal will
block both north and south edges.
As a counterpart, the Edge capacity is not decreased when the
global router connect to a terminal.
* Change: In Katana::RoutingEvent::revalidate(), when in repair stage,
do not expand the slack for horizontal segments in channel mode.
So they may not overlap the standard cell row.
* Bug: In Stratus documentation, do not use the french option in babel,
the documentation is in english!
* New: In Documentation, added Hurricane/Python tutorial, part for drawing
layout.
* New: In Anabatic::Edge::ripup(), sort edges to ripup by decreasing
length so the longest gets riped up first.
In two metals mode, ripup all segments *except* those who have
terminal contact in the GCell, because they must use it anyway.
* Bug: In Anabatic::GCell::getEdgeAt(), the size hint flag was not
correctly selected, leading to the use of an edge in the wrong
side. So deleted segments where not deleted from their edges,
leading to core dump. Don't understand how it can have not shown
until now.
* New: In KatanaEngine::annotateGlobalGraph(), for two metal gauges,
decrease the edge capacity on both north and south side for each
terminal in the GCell. As a terminal must be accessed through
north or south it blocks the whole vertical track (hence both
edges).
* Bug: In AnabaticEngine::loadGlobalRouting(), call relaxOverconstraineds()
only if we are *not* in two-metal mode.
* Bug: In NetBuilder::construct(), allow any number of globals (up to 6)
when in two-metal mode. Should be sufficent for now.
* New: In AnabaticEngine, new method _updateGContacts() to re-compute
the positions of the global routing contacts *after* a GCell
resize.
* Bug: In Katana::Block::resizeChannels(), must call _updateGContacts()
after the resize to properly shift their positions.
* Bug: In Anabatic::AutoSegment::computeOptimal(), the "side stack"
computing the intersection of all the sides of the GCell that the
segment is going through was implicitly supposing that the
resulting intersection wasn't empty. But for analog segment, we
compute the position of all the segments linked though simple
doglegs, and as dogleg occurs there can be a sufficient shift
so the intersections of all the sides became empty.
Now the "side stack" can manage configuration when instead
of having an intersection we have a "hole" in the GCell side
span (only one hole is supported at the moment). When a hole
is present, the optimal position is the center of the hole.
Should be refined so that the position is computed according
to the longest GCell that we go through.
* Change: In Katana::SegmentFsm::_slackenGlobal(), when slackening
a global from a ananlog net, allow to make a dog leg once
instead of immediately moving up. The break point is the center
of the segment.
* Change: In Katana::Manipulator::Makedogleg(DbU::Unit) if the break
position is over a device, choose the left of right GCell.
* New: In Anabatic::EdgeCapacity, dedicated object to manage the capacities
of an edge by layer. This needed now because with real technologies
layers capacities differs (unlike with symbolic technologies).
This object is separated to be shared between Edges with identical
characteristics (direction+interval). Deletion is automatic and
done through refcounting. All the already allocateds EdgeCapacity
are kept into a set in the AnabaticEngine (key is (direction,interval)).
* New: In Anabatic::Edge, capacities are stored in a shared EdgeCapacity
object. The total capacity can be annotated (i.e. decreased).
EdgeCapacity attribute is created during the materialize() call.
The capacities are computed at this time.
The incCapacity() function is renamed in reserveCapacity().
* New: In Anabatic::AnabaticEngine, added attribute _edgeCapacitiesLut
to store the shared EdgeCapacity.
Lookup/Creation of an EdgeCapacity is done through _createCapacity().
* Change: In Anabatic::Constants, rename Flags::IllimitedCapacity into
Flags::InfiniteCapacity. Add Flags::NullCapacity (both for Edges).
* Change: In Anabatic::GCell, implement a by depth (for layer) getCapacity().
This modification did expose a bug in the density calculation :
per depth density where divided by the complete density instead of the
density's depth. This was leading to greatly underestimated densities.
Thoses underestimations where preventing Dijkstra and layer assignement
to manage congestion correctly (in fact, it was acting as if there
never was congestion).
Also avoid a divide by zero (thus -NAN showing in densities).
* Change: In Anabatic::GCell, rename setEdgeOccupancy() into the more
accurate forceEdgesCapacities().
Note for Eric: only the first Edge on each side has it's capacity
forced. What if there's more than one Edge ?
* New: In Commons, inspector support for std::pair<T,U>.
* New: In Hurricane::Layer, ContactLayer & ViaLayer, support for non
square VIAs. The hole (cut) remains square, but the various metal
extensions can now be different in X and Y. The ::getEnclosure()
method now takes a flag EnclosureH / EnclosureV.
* New: In Hurricane::DbU, inspector support for:
std::pair<DbU::Unit,DbU::Unit>
std::array<DbU::Unit,3>
Must be defined here as DbU do not exists yet in Commons.h
* Bug: In Hurricane::Interval::getSize(), when the interval is "full span",
do not return the difference between min and max, but directly DbU::Max.
(the previous result was -1 !)
* New: In CRL Core Python/Technology.py, support for non square VIAs in
the configuration files. Applied to FreePDK 45.
* New: In CRL::RoutingGauge, added a "symbolic" flag to tell if a gauge
is for symbolic layout or not. Exported to Python.
* New: In Anabatic::AutoHorizontal::updatePosition(), differentiated
computation for soure or target taking account of the VIA extension
in the right segment metal (due to non-square VIAs).
* Change: In Anabatic::AutoHorizontal::_makeDogleg(), the dogleg is
UP for HV gauges and DOWN for VH.
* New: In Anabatic::AutoSegment::_initialize(), create a cache of the
various extension length for each layer (viaToTop, viaToBottom,
viaToSame).
New implementation of getExtensionCap() using the previous cached
extension table. See updatePositions().
New static functions to access the extension cache in the header:
getViaTotopCap() ...
* Change: In Anabatic::AutoSegment, in various update methods, updateOrient()
must always be called *before* updatePositions() as extensions are
dependant on source/target.
* New: In Anabatic::AutoSegment::getEndAxes() compute the position of the
first source and last target position (center/axes) on an *aligned*
set of segments.
* New: In Anabatic::AutoSegment, add a new state flag SegAxisFixed to
signal segments that can be put on only one track. Specific case
to VH gauge for a M1 vertical terminal with a M2 vertical segment.
The M2 is effectively bound to the M1 axis position.
* Bug: In Anabatic::NetBuilderVH::_do_xG_xM1_xM3(), in case of E/W global
and only one RoutingPad the connexion to the RoutingPad was duplicated.
It was valid, but totally stupid.
* Bug: In Anabatic::Session::_canonize(), for an aligned segment set,
intersect the user constraints from all segments instead of only
considering the canonical one.
Issue a warning about too tight constraints only for symbolic
gauges. It may be correct for the real ones.
* New: In Katata::DataNegociate::update(), more accurate computation
of the perpandicular free interval. Use segment extension cap
calculation. Create a special case for fixed axis segments allowing
them to find alternative free interval, try under source and under
target as they are likely to be draggable segments.
* Change: In Katana::Manipulator::relax(), use the extension cap value
to compute the axis of the perpandicular segemnts.
* Change: In Katana::Manipulator::moveUp(), now move up the whole set
of aligned segments instead of just the canonical one.
* Change: In Katana::NegociateWindow::loadRoutingPads(), more accurate
TrackMarkers insertions for fixed terminals.
* New: In Katana::RoutingEvent::Key::Compare::operator(), segments with
fixed axis are processed prior to any others.
* New: In Katana::RoutingEventLoop, store segment pointers instead of
ids to generate more accurate error messages.
* Change: In Katana::RoutingPlane::create(), perform local track
assignment only for HV gauges.
* Change: In Katana::SegmentFsm::_slackenLocal(), add a "dragMinimize"
step in the automaton. Mutliple states transitions can occurs in
a row if an action fails.
* New: In Katana::Session::_toIntervalAxis(), normalize interval
bounds so they are on track positions (by shrinking the interval).
* Bug: In Katana::TrackMarker CTOR, the weigh computation was wrong.
* New: In Anabatic & Katana, add the new "drag" feature.
With VH gauges used by real technologies (M1-H, M2-V, M3-H) a new
routing configuration that was not efficiently handled did appear.
While the preferred routing direction for metal1 is officially
horizontal, due to the way the standard cell must be designed,
their metal1 terminals are still verticals (or punctuals).
Thus, when connecting to them, we face the case where the metal1
terminal (RoutingPad) is vertical *and* the metal2 wire is also
vertical. With that setup, the position of the AutoContactTerminal
via12 cannot be deduced, it may range all the way over the
metal1 RoutingPad. What may define it's position is the metal3 the
metal2 finally connects to. That, is, when we have one horizontal
(the metal3) and one vertical (the metal1 RoutingPad).
The intermediate wire of metal2 can be kept to a minimum size
by "dragging" the via12 close to the via23 when the metal3 wire is
moved.
* New: In Anabatic & Katana, problem of closely vertically aligneds
RoutingPads in metal1 is managed first in PreProcess by restricting
the span of the connecteds metal3 and in _makeDogleg also by restricting
the span even more tightly (to the RoutingPad itself).
* New: In Anabatic::AutoContactTerminal, add the "drag" support.
Automatically check if the connecting segment is in the same
direction as the RoutingPad, if so, sets the "SegDrag" flag.
The dragging state can be known with the "::canDrag()" predicate.
* New: In Anabatic::AutoHorizontal, add the "drag" support.
The drag state can be known with the "::isDrag()" predicate.
In "::_makeDogleg()", when making a dogleg on a dragable segment
pass the drag state correctly and restrict the perpandicular span
of the perpandicular to the RoutingPad (though segment user constraints).
If we make a dogleg on the metal2 is it likely than we cannot go
straigth out vertically from the RoutingPad, so the new perpandicular
*is* restricted to the RoutingPad span.
Idem for AutoVertical.
* New: In Katana::Manipulator, add method "::dragMinimize()" which find a
hole where to minimize a draggable segment. We finally did not use it,
but keep it for potential further use.
* New: In Katana::PreProcess, adds a "protectAlignedaccesses()" local
function to check for vertically aligned metal1 RoutingPads, in that
case setup user constraints on the metal3 segments so they cannot
completly cover the other RoutingPad with metal2.
We also keep a "metal2protect()" function that create a fixed segment
to lock/protect a RoutingPad. Not used for now.
* New: In Katana::Session, add a RoutingPad locking event mechanism.
This allows us to request the creation of a locking (fixed segment)
over a draggable segment. Not used for now.
Lock events are processeds before all others as they create new
TrackElements.
* New: In Katana::Track, "::getNextFree()" and "::getPreviousFree()"
method to find the nearest free interval in a Track after/before a
position.
* Bug: In Anabatic::AutoHorizontal::getConstraints(), merge with user
constraints *only* if it's not an empty interval (as we use min/max
functions). Idem for AutoVertical.
* Bug: In AutoSegments_OnContacts::Locator::isValid(), the boolean test
must be inverted. Seems it never worked, but we never used it until
now...
* Change: In Anabatic::GCell::doGrid(), remove the "3 slice height"
limit (for small digital analog blocs).
* Bug: In Anabatic::NetBuilder::setStartHook(), perform a check for
a RoutingPad still on a Plug. Diplay an error instead of crashing.
* Bug: In CRL::RoutingLayerGauge::getTrackIndex(), the upper bound
of the track interval must be included instead of excluded.
* New: In Hurricane::Cell, add a StayOnPlugs flags for flattenNets().
To keep the RoutingPad occurrences on Plug instead of selecting
physical components.
* New: In Isobar::PyNet, add setAutomatic() and isAutomatic() to the
interface.
* Bug: In Katana::protectRoutingPads(), do not create protections on
PinOnly layers (mostly metal1).
* Bug: In Katana::PreProcess::protectCagedTerminals(), the contacts of
the fixed segment must be fixed too.
* Change: In Katana::RoutingPlane constructor, more accurate computation
of the extensionCap (for real technologies).
* Bug: In Katana::DataNegociate::update(), the perpandicular free
interval must be shrunk of the extensionCap of the perpandicular
layer. This problem did show with metal1 "half-offgrid" terminals.
* Change: In Katana::runGlobalRouter(), increase the number of ripup
passes to ten. Display the overloaded edges and the related nets.
* New: In Anabatic::NetBuilder, set all the attributes as private and
create accessors and mutators.
Finish virtualising all GCell build methods and transfer them
into the NetBuilderHV class.
Build methods now return a boolean to tell if the GCell was
processed or not, to allow cascading in the "big switch".
Reorganise the "big switch" in separate sections only partially
cascading.
Truly fuse the *big switch* for channel routing and over-the-cells.
Create a new method "_do_globalSegment()" to delagate the
drawing of global segments between two GCell to the derived classes.
* Bug: In Kite::NegociateWidow and Katana::NegociateWindow, when creating
the TrackSegment from the AutoSegment, we put it on the nearest track
from its current position. But it may happens that the nearest track
is outside the terminal constraint interval (in the case of "nsxlib").
Add the terminal constraint interval check.
This was not affecting the routing result because the segment was
put inside the right interval afterwards. It was only generating
disgraceful transient error messages...
Jean-Paul Chaput
Luke Kenneth Casson Leighton
EricLaoGitHub