Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
// -*- C++ -*-
|
|
|
|
//
|
|
|
|
// This file is part of the Coriolis Software.
|
|
|
|
// Copyright (c) UPMC 2014-2014, All Rights Reserved
|
|
|
|
//
|
|
|
|
// +-----------------------------------------------------------------+
|
|
|
|
// | C O R I O L I S |
|
|
|
|
// | K i t e - D e t a i l e d R o u t e r |
|
|
|
|
// | |
|
|
|
|
// | Author : Jean-Paul CHAPUT |
|
|
|
|
// | E-mail : Jean-Paul.Chaput@asim.lip6.fr |
|
|
|
|
// | =============================================================== |
|
|
|
|
// | C++ Module : "./BuildPreRouteds.cpp" |
|
|
|
|
// +-----------------------------------------------------------------+
|
|
|
|
|
|
|
|
|
|
|
|
#include <map>
|
|
|
|
#include <list>
|
|
|
|
#include "hurricane/Error.h"
|
|
|
|
#include "hurricane/Warning.h"
|
|
|
|
#include "hurricane/DataBase.h"
|
|
|
|
#include "hurricane/Technology.h"
|
|
|
|
#include "hurricane/BasicLayer.h"
|
|
|
|
#include "hurricane/RegularLayer.h"
|
|
|
|
#include "hurricane/Horizontal.h"
|
|
|
|
#include "hurricane/Vertical.h"
|
|
|
|
#include "hurricane/RoutingPad.h"
|
|
|
|
#include "hurricane/NetExternalComponents.h"
|
Add management of fixed wires to Kite (for chip ClockTree)
* Change: In Hurricane, in Plug::setNet(), more informative error messages.
* Change: In Hurricane, In Segment, more informative error messages.
* Change: In Hurricane, In DeepNet, accessor for the Net occurrence.
* Bug: In Katabatic, in AutoSegment::create(), error message uses correct
variables (vertical was using horizontal)...
* Change: In Kite, in BuildPowerRails, already existing wiring in instances
is copied up as blockage. Uses blockage layer instead of true layer
(it was a bug).
* Change: In Kite, in BuildPreRouted, consider as manual global routing
nets with only default wiring (default size wire & contacts).
Non-default routing is flagged as fixed (with the NetRoutingState
property).
2014-08-15 12:26:49 -05:00
|
|
|
#include "hurricane/DeepNet.h"
|
Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
#include "hurricane/Instance.h"
|
|
|
|
#include "hurricane/Plug.h"
|
|
|
|
#include "hurricane/Path.h"
|
|
|
|
#include "hurricane/Query.h"
|
|
|
|
#include "crlcore/AllianceFramework.h"
|
Add NetRoutingState (Property) on Nets to tell Kite what to do.
* New: In Katabatic, add the ability to decorate some (i.e. few) nets
with a state that indicate to Katabatic & Kite what to do with it.
The possible states are:
1. Fixed : all the wire are in fixed positions. The router cannot
move them and account them as obstacles.
2. ManualGlobalRoute : a user-defined topology is supplied. The
wires still have to be detailed route in "Detailed Pre-Route"
but will be skipped for the global routing and fixed for the
general Detailed route.
3. AutomaticGlobalRoute : ordinary nets, to be global routed then
detail routed.
4. Excluded : do not try to global or detail route thoses nets.
5. MixedPreRoute : mask combining Fixed and ManualGlobalRoute.
Not all nets have this property, only those that needs a special
processing.
To ease the access to the state, it is nested inside a
PrivateProperty in the net (NetRoutingProperty), with an extension
access class (NetRoutingExtension).
* New: In Kite, take account of NetRoutingState. Pointers to the
net's states are strored inside an internal map for faster access.
The property is *not* deleted when Kite is destroyed. The property
will remains until the Net itself is destroyed.
As a consequence, the lists that where passed to high level
function are removed as the information can now be accessed directly
through the net NetRoutingProperty.
* New: In Unicorn, in CgtMain, comply with the update interface.
* New: In documentation, update the User's Guide to explain the Pre-routed
step of Kite.
2014-07-02 07:36:58 -05:00
|
|
|
#include "katabatic/NetRoutingProperty.h"
|
Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
#include "katabatic/AutoContact.h"
|
|
|
|
#include "kite/RoutingPlane.h"
|
|
|
|
#include "kite/TrackFixedSegment.h"
|
|
|
|
#include "kite/Track.h"
|
|
|
|
#include "kite/KiteEngine.h"
|
|
|
|
|
|
|
|
|
|
|
|
namespace {
|
|
|
|
|
Add NetRoutingState (Property) on Nets to tell Kite what to do.
* New: In Katabatic, add the ability to decorate some (i.e. few) nets
with a state that indicate to Katabatic & Kite what to do with it.
The possible states are:
1. Fixed : all the wire are in fixed positions. The router cannot
move them and account them as obstacles.
2. ManualGlobalRoute : a user-defined topology is supplied. The
wires still have to be detailed route in "Detailed Pre-Route"
but will be skipped for the global routing and fixed for the
general Detailed route.
3. AutomaticGlobalRoute : ordinary nets, to be global routed then
detail routed.
4. Excluded : do not try to global or detail route thoses nets.
5. MixedPreRoute : mask combining Fixed and ManualGlobalRoute.
Not all nets have this property, only those that needs a special
processing.
To ease the access to the state, it is nested inside a
PrivateProperty in the net (NetRoutingProperty), with an extension
access class (NetRoutingExtension).
* New: In Kite, take account of NetRoutingState. Pointers to the
net's states are strored inside an internal map for faster access.
The property is *not* deleted when Kite is destroyed. The property
will remains until the Net itself is destroyed.
As a consequence, the lists that where passed to high level
function are removed as the information can now be accessed directly
through the net NetRoutingProperty.
* New: In Unicorn, in CgtMain, comply with the update interface.
* New: In documentation, update the User's Guide to explain the Pre-routed
step of Kite.
2014-07-02 07:36:58 -05:00
|
|
|
|
|
|
|
} // Anonymous namespace.
|
|
|
|
|
|
|
|
|
|
|
|
namespace Kite {
|
|
|
|
|
Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
using namespace std;
|
|
|
|
using Hurricane::tab;
|
|
|
|
using Hurricane::inltrace;
|
|
|
|
using Hurricane::ltracein;
|
|
|
|
using Hurricane::ltraceout;
|
|
|
|
using Hurricane::ForEachIterator;
|
|
|
|
using Hurricane::Warning;
|
|
|
|
using Hurricane::Error;
|
|
|
|
using Hurricane::DbU;
|
|
|
|
using Hurricane::Box;
|
|
|
|
using Hurricane::Interval;
|
|
|
|
using Hurricane::Horizontal;
|
|
|
|
using Hurricane::Vertical;
|
|
|
|
using Hurricane::RoutingPad;
|
|
|
|
using Hurricane::NetExternalComponents;
|
Add management of fixed wires to Kite (for chip ClockTree)
* Change: In Hurricane, in Plug::setNet(), more informative error messages.
* Change: In Hurricane, In Segment, more informative error messages.
* Change: In Hurricane, In DeepNet, accessor for the Net occurrence.
* Bug: In Katabatic, in AutoSegment::create(), error message uses correct
variables (vertical was using horizontal)...
* Change: In Kite, in BuildPowerRails, already existing wiring in instances
is copied up as blockage. Uses blockage layer instead of true layer
(it was a bug).
* Change: In Kite, in BuildPreRouted, consider as manual global routing
nets with only default wiring (default size wire & contacts).
Non-default routing is flagged as fixed (with the NetRoutingState
property).
2014-08-15 12:26:49 -05:00
|
|
|
using Hurricane::DeepNet;
|
Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
using Hurricane::Instance;
|
|
|
|
using Hurricane::Plug;
|
|
|
|
using Hurricane::Path;
|
|
|
|
using Hurricane::Query;
|
|
|
|
using Hurricane::Go;
|
|
|
|
using Hurricane::Rubber;
|
|
|
|
using Hurricane::Layer;
|
|
|
|
using Hurricane::BasicLayer;
|
|
|
|
using Hurricane::RegularLayer;
|
|
|
|
using Hurricane::Transformation;
|
|
|
|
using Hurricane::Technology;
|
|
|
|
using Hurricane::DataBase;
|
|
|
|
using CRL::AllianceFramework;
|
Add NetRoutingState (Property) on Nets to tell Kite what to do.
* New: In Katabatic, add the ability to decorate some (i.e. few) nets
with a state that indicate to Katabatic & Kite what to do with it.
The possible states are:
1. Fixed : all the wire are in fixed positions. The router cannot
move them and account them as obstacles.
2. ManualGlobalRoute : a user-defined topology is supplied. The
wires still have to be detailed route in "Detailed Pre-Route"
but will be skipped for the global routing and fixed for the
general Detailed route.
3. AutomaticGlobalRoute : ordinary nets, to be global routed then
detail routed.
4. Excluded : do not try to global or detail route thoses nets.
5. MixedPreRoute : mask combining Fixed and ManualGlobalRoute.
Not all nets have this property, only those that needs a special
processing.
To ease the access to the state, it is nested inside a
PrivateProperty in the net (NetRoutingProperty), with an extension
access class (NetRoutingExtension).
* New: In Kite, take account of NetRoutingState. Pointers to the
net's states are strored inside an internal map for faster access.
The property is *not* deleted when Kite is destroyed. The property
will remains until the Net itself is destroyed.
As a consequence, the lists that where passed to high level
function are removed as the information can now be accessed directly
through the net NetRoutingProperty.
* New: In Unicorn, in CgtMain, comply with the update interface.
* New: In documentation, update the User's Guide to explain the Pre-routed
step of Kite.
2014-07-02 07:36:58 -05:00
|
|
|
using Hurricane::ForEachIterator;
|
|
|
|
using Katabatic::NetRoutingExtension;
|
|
|
|
using Katabatic::NetRoutingState;
|
Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
using Katabatic::AutoContact;
|
|
|
|
using Katabatic::AutoSegment;
|
|
|
|
using Katabatic::ChipTools;
|
|
|
|
|
|
|
|
|
|
|
|
void KiteEngine::buildPreRouteds ()
|
|
|
|
{
|
Add management of fixed wires to Kite (for chip ClockTree)
* Change: In Hurricane, in Plug::setNet(), more informative error messages.
* Change: In Hurricane, In Segment, more informative error messages.
* Change: In Hurricane, In DeepNet, accessor for the Net occurrence.
* Bug: In Katabatic, in AutoSegment::create(), error message uses correct
variables (vertical was using horizontal)...
* Change: In Kite, in BuildPowerRails, already existing wiring in instances
is copied up as blockage. Uses blockage layer instead of true layer
(it was a bug).
* Change: In Kite, in BuildPreRouted, consider as manual global routing
nets with only default wiring (default size wire & contacts).
Non-default routing is flagged as fixed (with the NetRoutingState
property).
2014-08-15 12:26:49 -05:00
|
|
|
cmess1 << " o Looking for fixed or manually global routed nets." << endl;
|
|
|
|
|
Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
forEach ( Net*, inet, getCell()->getNets() ) {
|
|
|
|
if (*inet == _blockageNet) continue;
|
|
|
|
if (inet->getType() == Net::Type::POWER ) continue;
|
|
|
|
if (inet->getType() == Net::Type::GROUND) continue;
|
Add management of fixed wires to Kite (for chip ClockTree)
* Change: In Hurricane, in Plug::setNet(), more informative error messages.
* Change: In Hurricane, In Segment, more informative error messages.
* Change: In Hurricane, In DeepNet, accessor for the Net occurrence.
* Bug: In Katabatic, in AutoSegment::create(), error message uses correct
variables (vertical was using horizontal)...
* Change: In Kite, in BuildPowerRails, already existing wiring in instances
is copied up as blockage. Uses blockage layer instead of true layer
(it was a bug).
* Change: In Kite, in BuildPreRouted, consider as manual global routing
nets with only default wiring (default size wire & contacts).
Non-default routing is flagged as fixed (with the NetRoutingState
property).
2014-08-15 12:26:49 -05:00
|
|
|
// Don't skip the clock.
|
Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
|
|
|
|
vector<Segment*> segments;
|
|
|
|
vector<Contact*> contacts;
|
|
|
|
|
|
|
|
bool isPreRouted = false;
|
Add management of fixed wires to Kite (for chip ClockTree)
* Change: In Hurricane, in Plug::setNet(), more informative error messages.
* Change: In Hurricane, In Segment, more informative error messages.
* Change: In Hurricane, In DeepNet, accessor for the Net occurrence.
* Bug: In Katabatic, in AutoSegment::create(), error message uses correct
variables (vertical was using horizontal)...
* Change: In Kite, in BuildPowerRails, already existing wiring in instances
is copied up as blockage. Uses blockage layer instead of true layer
(it was a bug).
* Change: In Kite, in BuildPreRouted, consider as manual global routing
nets with only default wiring (default size wire & contacts).
Non-default routing is flagged as fixed (with the NetRoutingState
property).
2014-08-15 12:26:49 -05:00
|
|
|
bool isFixed = false;
|
|
|
|
size_t rpCount = 0;
|
|
|
|
|
|
|
|
if (inet->isDeepNet()) {
|
|
|
|
rpCount = 2;
|
|
|
|
|
|
|
|
Net* rootNet = dynamic_cast<Net*>(
|
|
|
|
dynamic_cast<DeepNet*>(*inet)->getRootNetOccurrence().getEntity() );
|
|
|
|
forEach ( Component*, icomponent, rootNet->getComponents() ) {
|
|
|
|
if (dynamic_cast<Horizontal*>(*icomponent)) { isFixed = true; break; }
|
|
|
|
if (dynamic_cast<Vertical*> (*icomponent)) { isFixed = true; break; }
|
|
|
|
if (dynamic_cast<Contact*> (*icomponent)) { isFixed = true; break; }
|
|
|
|
}
|
|
|
|
} else {
|
|
|
|
forEach ( Component*, icomponent, inet->getComponents() ) {
|
|
|
|
Horizontal* horizontal = dynamic_cast<Horizontal*>(*icomponent);
|
|
|
|
if (horizontal) {
|
|
|
|
segments.push_back( horizontal );
|
Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
isPreRouted = true;
|
Add management of fixed wires to Kite (for chip ClockTree)
* Change: In Hurricane, in Plug::setNet(), more informative error messages.
* Change: In Hurricane, In Segment, more informative error messages.
* Change: In Hurricane, In DeepNet, accessor for the Net occurrence.
* Bug: In Katabatic, in AutoSegment::create(), error message uses correct
variables (vertical was using horizontal)...
* Change: In Kite, in BuildPowerRails, already existing wiring in instances
is copied up as blockage. Uses blockage layer instead of true layer
(it was a bug).
* Change: In Kite, in BuildPreRouted, consider as manual global routing
nets with only default wiring (default size wire & contacts).
Non-default routing is flagged as fixed (with the NetRoutingState
property).
2014-08-15 12:26:49 -05:00
|
|
|
if (horizontal->getWidth() != Session::getWireWidth(horizontal->getLayer()))
|
|
|
|
isFixed = true;
|
Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
} else {
|
Add management of fixed wires to Kite (for chip ClockTree)
* Change: In Hurricane, in Plug::setNet(), more informative error messages.
* Change: In Hurricane, In Segment, more informative error messages.
* Change: In Hurricane, In DeepNet, accessor for the Net occurrence.
* Bug: In Katabatic, in AutoSegment::create(), error message uses correct
variables (vertical was using horizontal)...
* Change: In Kite, in BuildPowerRails, already existing wiring in instances
is copied up as blockage. Uses blockage layer instead of true layer
(it was a bug).
* Change: In Kite, in BuildPreRouted, consider as manual global routing
nets with only default wiring (default size wire & contacts).
Non-default routing is flagged as fixed (with the NetRoutingState
property).
2014-08-15 12:26:49 -05:00
|
|
|
Vertical* vertical = dynamic_cast<Vertical*>(*icomponent);
|
|
|
|
if (vertical) {
|
Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
isPreRouted = true;
|
Add management of fixed wires to Kite (for chip ClockTree)
* Change: In Hurricane, in Plug::setNet(), more informative error messages.
* Change: In Hurricane, In Segment, more informative error messages.
* Change: In Hurricane, In DeepNet, accessor for the Net occurrence.
* Bug: In Katabatic, in AutoSegment::create(), error message uses correct
variables (vertical was using horizontal)...
* Change: In Kite, in BuildPowerRails, already existing wiring in instances
is copied up as blockage. Uses blockage layer instead of true layer
(it was a bug).
* Change: In Kite, in BuildPreRouted, consider as manual global routing
nets with only default wiring (default size wire & contacts).
Non-default routing is flagged as fixed (with the NetRoutingState
property).
2014-08-15 12:26:49 -05:00
|
|
|
segments.push_back( vertical );
|
|
|
|
if (vertical->getWidth() != Session::getWireWidth(vertical->getLayer()))
|
|
|
|
isFixed = true;
|
Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
} else {
|
Add management of fixed wires to Kite (for chip ClockTree)
* Change: In Hurricane, in Plug::setNet(), more informative error messages.
* Change: In Hurricane, In Segment, more informative error messages.
* Change: In Hurricane, In DeepNet, accessor for the Net occurrence.
* Bug: In Katabatic, in AutoSegment::create(), error message uses correct
variables (vertical was using horizontal)...
* Change: In Kite, in BuildPowerRails, already existing wiring in instances
is copied up as blockage. Uses blockage layer instead of true layer
(it was a bug).
* Change: In Kite, in BuildPreRouted, consider as manual global routing
nets with only default wiring (default size wire & contacts).
Non-default routing is flagged as fixed (with the NetRoutingState
property).
2014-08-15 12:26:49 -05:00
|
|
|
Contact* contact = dynamic_cast<Contact*>(*icomponent);
|
|
|
|
if (contact) {
|
|
|
|
isPreRouted = true;
|
|
|
|
contacts.push_back( contact );
|
|
|
|
if ( (contact->getWidth () != Session::getViaWidth(contact->getLayer()))
|
|
|
|
or (contact->getHeight() != Session::getViaWidth(contact->getLayer())) )
|
|
|
|
isFixed = true;
|
Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
} else {
|
Add management of fixed wires to Kite (for chip ClockTree)
* Change: In Hurricane, in Plug::setNet(), more informative error messages.
* Change: In Hurricane, In Segment, more informative error messages.
* Change: In Hurricane, In DeepNet, accessor for the Net occurrence.
* Bug: In Katabatic, in AutoSegment::create(), error message uses correct
variables (vertical was using horizontal)...
* Change: In Kite, in BuildPowerRails, already existing wiring in instances
is copied up as blockage. Uses blockage layer instead of true layer
(it was a bug).
* Change: In Kite, in BuildPreRouted, consider as manual global routing
nets with only default wiring (default size wire & contacts).
Non-default routing is flagged as fixed (with the NetRoutingState
property).
2014-08-15 12:26:49 -05:00
|
|
|
RoutingPad* rp = dynamic_cast<RoutingPad*>(*icomponent);
|
|
|
|
if (rp) {
|
|
|
|
++rpCount;
|
|
|
|
} else {
|
|
|
|
// Plug* plug = dynamic_cast<Plug*>(*icomponent);
|
|
|
|
// if (plug) {
|
|
|
|
// cerr << "buildPreRouteds(): " << plug << endl;
|
|
|
|
// ++rpCount;
|
|
|
|
// }
|
|
|
|
}
|
Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
Add management of fixed wires to Kite (for chip ClockTree)
* Change: In Hurricane, in Plug::setNet(), more informative error messages.
* Change: In Hurricane, In Segment, more informative error messages.
* Change: In Hurricane, In DeepNet, accessor for the Net occurrence.
* Bug: In Katabatic, in AutoSegment::create(), error message uses correct
variables (vertical was using horizontal)...
* Change: In Kite, in BuildPowerRails, already existing wiring in instances
is copied up as blockage. Uses blockage layer instead of true layer
(it was a bug).
* Change: In Kite, in BuildPreRouted, consider as manual global routing
nets with only default wiring (default size wire & contacts).
Non-default routing is flagged as fixed (with the NetRoutingState
property).
2014-08-15 12:26:49 -05:00
|
|
|
if (isFixed or isPreRouted or (rpCount < 2)) {
|
Add NetRoutingState (Property) on Nets to tell Kite what to do.
* New: In Katabatic, add the ability to decorate some (i.e. few) nets
with a state that indicate to Katabatic & Kite what to do with it.
The possible states are:
1. Fixed : all the wire are in fixed positions. The router cannot
move them and account them as obstacles.
2. ManualGlobalRoute : a user-defined topology is supplied. The
wires still have to be detailed route in "Detailed Pre-Route"
but will be skipped for the global routing and fixed for the
general Detailed route.
3. AutomaticGlobalRoute : ordinary nets, to be global routed then
detail routed.
4. Excluded : do not try to global or detail route thoses nets.
5. MixedPreRoute : mask combining Fixed and ManualGlobalRoute.
Not all nets have this property, only those that needs a special
processing.
To ease the access to the state, it is nested inside a
PrivateProperty in the net (NetRoutingProperty), with an extension
access class (NetRoutingExtension).
* New: In Kite, take account of NetRoutingState. Pointers to the
net's states are strored inside an internal map for faster access.
The property is *not* deleted when Kite is destroyed. The property
will remains until the Net itself is destroyed.
As a consequence, the lists that where passed to high level
function are removed as the information can now be accessed directly
through the net NetRoutingProperty.
* New: In Unicorn, in CgtMain, comply with the update interface.
* New: In documentation, update the User's Guide to explain the Pre-routed
step of Kite.
2014-07-02 07:36:58 -05:00
|
|
|
NetRoutingState* state = getRoutingState( *inet, Katabatic::KbCreate );
|
|
|
|
state->unsetFlags( NetRoutingState::AutomaticGlobalRoute );
|
Add management of fixed wires to Kite (for chip ClockTree)
* Change: In Hurricane, in Plug::setNet(), more informative error messages.
* Change: In Hurricane, In Segment, more informative error messages.
* Change: In Hurricane, In DeepNet, accessor for the Net occurrence.
* Bug: In Katabatic, in AutoSegment::create(), error message uses correct
variables (vertical was using horizontal)...
* Change: In Kite, in BuildPowerRails, already existing wiring in instances
is copied up as blockage. Uses blockage layer instead of true layer
(it was a bug).
* Change: In Kite, in BuildPreRouted, consider as manual global routing
nets with only default wiring (default size wire & contacts).
Non-default routing is flagged as fixed (with the NetRoutingState
property).
2014-08-15 12:26:49 -05:00
|
|
|
state->setFlags ( NetRoutingState::ManualGlobalRoute );
|
Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
|
Add management of fixed wires to Kite (for chip ClockTree)
* Change: In Hurricane, in Plug::setNet(), more informative error messages.
* Change: In Hurricane, In Segment, more informative error messages.
* Change: In Hurricane, In DeepNet, accessor for the Net occurrence.
* Bug: In Katabatic, in AutoSegment::create(), error message uses correct
variables (vertical was using horizontal)...
* Change: In Kite, in BuildPowerRails, already existing wiring in instances
is copied up as blockage. Uses blockage layer instead of true layer
(it was a bug).
* Change: In Kite, in BuildPreRouted, consider as manual global routing
nets with only default wiring (default size wire & contacts).
Non-default routing is flagged as fixed (with the NetRoutingState
property).
2014-08-15 12:26:49 -05:00
|
|
|
if (isFixed) {
|
|
|
|
cmess2 << " - <" << (*inet)->getName() << "> is fixed." << endl;
|
|
|
|
state->unsetFlags( NetRoutingState::ManualGlobalRoute );
|
|
|
|
state->setFlags ( NetRoutingState::Fixed );
|
|
|
|
} else {
|
|
|
|
if (rpCount > 1) {
|
|
|
|
cmess2 << " - <" << (*inet)->getName() << "> is manually global routed." << endl;
|
|
|
|
for ( auto icontact : contacts ) {
|
|
|
|
AutoContact::createFrom( icontact );
|
|
|
|
}
|
|
|
|
|
|
|
|
for ( auto isegment : segments ) {
|
|
|
|
AutoContact* source = Session::base()->lookup( dynamic_cast<Contact*>( isegment->getSource() ));
|
|
|
|
AutoContact* target = Session::base()->lookup( dynamic_cast<Contact*>( isegment->getTarget() ));
|
|
|
|
AutoSegment* autoSegment = AutoSegment::create( source, target, isegment );
|
|
|
|
autoSegment->setFlags( Katabatic::SegUserDefined|Katabatic::SegAxisSet );
|
|
|
|
}
|
Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
Add NetRoutingState (Property) on Nets to tell Kite what to do.
* New: In Katabatic, add the ability to decorate some (i.e. few) nets
with a state that indicate to Katabatic & Kite what to do with it.
The possible states are:
1. Fixed : all the wire are in fixed positions. The router cannot
move them and account them as obstacles.
2. ManualGlobalRoute : a user-defined topology is supplied. The
wires still have to be detailed route in "Detailed Pre-Route"
but will be skipped for the global routing and fixed for the
general Detailed route.
3. AutomaticGlobalRoute : ordinary nets, to be global routed then
detail routed.
4. Excluded : do not try to global or detail route thoses nets.
5. MixedPreRoute : mask combining Fixed and ManualGlobalRoute.
Not all nets have this property, only those that needs a special
processing.
To ease the access to the state, it is nested inside a
PrivateProperty in the net (NetRoutingProperty), with an extension
access class (NetRoutingExtension).
* New: In Kite, take account of NetRoutingState. Pointers to the
net's states are strored inside an internal map for faster access.
The property is *not* deleted when Kite is destroyed. The property
will remains until the Net itself is destroyed.
As a consequence, the lists that where passed to high level
function are removed as the information can now be accessed directly
through the net NetRoutingProperty.
* New: In Unicorn, in CgtMain, comply with the update interface.
* New: In documentation, update the User's Guide to explain the Pre-routed
step of Kite.
2014-07-02 07:36:58 -05:00
|
|
|
Session::revalidate();
|
Implementation of pre-routing support (for clock-tree compliance).
* New: In Katabatic, in <AutoContact>, this class is no longer derived
from ExtentionGo. With the simplificated AutoContacts, there is no
reason to do so, and it will save some QuadTree insertions/deletions.
New factory function AutoContact::createFrom(Contact*) which try to
build an AutoContact on top of a Hurricane::Contact. Of course that
base contact *must fit* into one of the predefined Contact
configurations (Terminal, Turn, HTee or VTee).
NOTE: This implies that the pre-routed segments & contacts *are*
correctly articulated, which is not the case when a Cell is read
from disk in "ap" format. The pre-routing feature must be used for
now without any re-read from disk. We will implement a re-articulating
pre-process in the future.
* Change: In Katabatic, in <AutoContact> derived classes, the ::updateCache()
method now display an accurate error message if a segment is connected
but has no AutoSegment conterpart (i.e. the lookup fails).
* New: In Katabatic, in <AutoSegment>, the ::computeOptimal() method is
short-circuited for pre-routed segments, the optimal axis position is
considered to be the one it is currently on (i.e. we trust the designer).
* New: In Katabatic, in <KatabaticEngine>, the ::loadGlobalRouting()
method now accept a map of excluded nets (same as Knik). This map is
the one of pre-routed nets.
* New: In Katabatic, in layer assignment, do not try to displace fixed
segments...
* New: In Katabatic, in <AutoSegment>, new flag SegUserDefined and related
methods to know if a segment comes from the global router (Knik) or
is pre-routed (supplied by the user).
* New: In Kite, In <BuildPowerRails>, support (exclusion) for pre-routed
nets.
* New: In Kite, In <GraphicKiteEngine> new menu entry for running the
router on pre-routed nets ("Detailed Pre-Route"), also integrated
in the all-on-one route command.
* New: In Kite, In KiteEngine, new method ::_initDataBase() that group
all the initialisation steps. It is a mix of calls between Knik and
Kite initializations which are intertwinneds (may have to devellop
a shared common base at a later point). It creates the Knik grid,
then the Katabatic grid, then load pre-routed wires and power rails
and protect isolated RoutingPads.
Add support for a map of pre-routed nets (to be excluded for
Knik calls).
The method "::run()" now uses function flags, firstly to know if
it is managing pre-routed wires or general purposes ones.
* New: In Kite, in <NegociateWindow>, the "::run()" methods has now two
modes. The normal one and the 'KtPreRoutedStage' that is for routing
pre-routed nets. When in pre-route stage, the wires are fixed at the
end of this step.
* New: In Kite, in <TrackElement> add decorator for AutoSegment
isUsedDefined().
* New: In Kite, in <TrackSegment>, the various ::canDogleg() methods
returns false for a pre-routed (user-defined segment).
* New: In Kite, in PyKiteEngine, added new method runNegociatePreRouted().
2014-06-21 13:16:47 -05:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
void KiteEngine::setFixedPreRouted ()
|
|
|
|
{
|
|
|
|
for ( size_t depth=0 ; depth<_routingPlanes.size() ; ++depth ) {
|
|
|
|
RoutingPlane* rp = _routingPlanes[depth];
|
|
|
|
if (rp->getLayerGauge()->getType() == Constant::PinOnly ) continue;
|
|
|
|
if (rp->getLayerGauge()->getDepth() > getConfiguration()->getAllowedDepth() ) continue;
|
|
|
|
|
|
|
|
size_t tracksSize = rp->getTracksSize();
|
|
|
|
for ( size_t itrack=0 ; itrack<tracksSize ; ++itrack ) {
|
|
|
|
Track* track = rp->getTrackByIndex( itrack );
|
|
|
|
|
|
|
|
for ( size_t ielement=0 ; ielement<track->getSize() ; ++ielement ) {
|
|
|
|
TrackElement* element = track->getSegment( ielement );
|
|
|
|
|
|
|
|
if (element->getNet() == NULL) continue;
|
|
|
|
element->setRouted();
|
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
|
|
} // Kite namespace.
|