connections to the core side VCCD1 and VSSD1 on the clamped3 pads.
Also added scripts for running LVS on chip_io to the mag/ directory,
and revised the scripts so that they will only re-run extraction if
there is no netlist file in the mag/ directory.
gate-level simulations from running. Corrected caravan_netlists.v,
which did not have the same change made yesterday to caravel_netlists.v
for the DLL.
knowledge and which went undetected since before MPW-one. Modified
the "pll" and "sysctrl" testbenches so that they run and measure
something useful. Both exercise the clock monitoring on GPIO
outputs functions. The PLL test also runs the digital locked
loop (behavioral verilog). The PLL test overlaps sysctrl, but
"pll" cannot be run on gate level verilog, whereas "sysctrl" can.
(input for monitoring) changed from being connected directly to the
user project (where it shouldn't be) to the same signal on the input
side of the management protect block (where it should be). This is
functionally the same. Checked for any other signals connected
directly from the user project to any block other than mgmt_protect,
didn't find any (good). Modified the gate-level netlists and top-level
layouts for caravel and caravan with the corresponding change. This
was the only change affecting layout. Also: Revised the "pll"
testbench. This is still ongoing work. Also: Fixed the way the
pins on I/O pads are declared in chip_io.v, mprj_io.v, and pads.v, so
that it isn't so bizarre. Most of this change is functionally
agnostic (just a change in the way the ifdefs work), but did fix an
incorrect ifdef that causes the whole user power domain to be broken.
which is now done through setting an environment variable to point to the
location of the management SoC wrapper. Added the missing user project
wrappers to the GL directory (copied from the original caravel repository),
and also the GL version of chip_io_alt. Modified the caravan_netlists and
caravel_netlists files to import the correct list of gate level netlists,
which has been reduced by moving "include" statements for components of the
management SoC into the management SoC repository (e.g., caravel_pico).
the change in the implementation of the serial loader, which split the load
signal out as a separate bit, and therefore had a separate bit-bang entry).
to housekeeping and the management core wrapper to separate the
wb_cyc_i signal and connect to new signal hk_cyc_o on the
management core. Also: Fixed a dangling input (user_clock) on
the housekeeping (minor error caused by the earlier refactoring
and unnoticed because there is no testbench covering that
function).
blocks; that is, there are special versions of the block for the
first 6 GPIO pins. That should allow the GL netlists to simulate,
although the end goal is to have the gen_gpio_defaults.py script
modify the GL netlists to exactly match the configuration, as is
done for the .mag layouts.
add a separate signal for the houskeeping wb_cyc_i wishbone signal,
instead of combining it with the user project's wb_cyc_i. This
change makes it compatible with the LiteX implementation of the
wishbone bus.
to resolve the problem with the typo that caused the propagated
GPIO serial load, reset, and clock signals to get scrambled on the
user2 side. Caravel is now LVS clean again (Caravan needs layout
work).
verilog for both caravel and caravan. Hand-edited the RTL and GL netlists to
correct this; still need to correct the layouts. The error causes the user1
side clock, load, and reset buffers to drive the user2 side as well as the user1
side, making a huge mess of the routing. Will route this by hand.
Fixed rstb_h, which was being input to low-voltage blocks. (2)
Fixed flash_csb_ieb_core and flash_clk_ieb_core, which were not
output from housekeeping as they should be; the solution was
to tie the INP_DIS lines low at the pad by connecting them to
the TIE_LO_ESD line. This should probably be addressed in
housekeeping but would change the current pinout.
problems that had been fixed recently in caravel, and which cause
the caravan testbench to break, but which were not noticed; (2)
corrected the count of gpio_control_block modules, which was one
off, with two of them overlapping (not sure how that even passes
simulation, but it did); (3) fixed a power connection in the
caravel chip_io, which should have caused chip_io to fail LVS,
so apparently LVS was not run on chip_io. . .
got removed from its net by a chang in the LEF view of an I/O pad, and
a lack of declaration of an array to attach to pwr_ctrl_out in the
verilog, which is valid verilog but netgen can't know the bus size
without the no-connect net being declared. The remaining issue has to
do with separation of ground domains in the mgmt_protect block.
Tim Edwards
manarabdelaty
jeffdi