Merge branch 'main' of https://github.com/efabless/caravel_openframe into main

Makefile

@@ -796,6 +796,7 @@ endif
 
 __gpio_defaults:
 	mkdir -p ./signoff/build
+	mkdir -p ./verilog/gl
 	python3 $(CARAVEL_ROOT)/scripts/gen_gpio_defaults.py $(shell pwd) 2>&1 | tee ./signoff/build/gpio_defaults.out
 
 .PHONY: update_caravel

verilog/dv/caravel/mgmt_soc/pll/pll.c

@@ -21,12 +21,9 @@
 
 /*
  *	PLL Test (self-switching)
- *	- Enables SPI master
+ *      - Switches PLL bypass in housekeeping
- *	- Uses SPI master to internally access the housekeeping SPI
+ *	- Changes PLL divider in housekeeping
- *      - Switches PLL bypass
- *	- Changes PLL divider
  *
- * 	Tesbench mostly copied from sysctrl
  */
 void main()
 {
@@ -54,67 +51,89 @@ void main()
     reg_mprj_io_17 = GPIO_MODE_MGMT_STD_OUTPUT;
     reg_mprj_io_16 = GPIO_MODE_MGMT_STD_OUTPUT;
 
+    /* Monitor pins must be set to output */
+    reg_mprj_io_15 = GPIO_MODE_MGMT_STD_OUTPUT;
+    reg_mprj_io_14 = GPIO_MODE_MGMT_STD_OUTPUT;
+
     /* Apply configuration */
     reg_mprj_xfer = 1;
     while (reg_mprj_xfer == 1);
 
     // Start test
+
+    /*
+     *-------------------------------------------------------------
+     * Register 2610_000c	reg_hkspi_pll_ena
+     * SPI address 0x08 = PLL enables
+     * bit 0 = PLL enable, bit 1 = DCO enable
+     *
+     * Register 2610_0010	reg_hkspi_pll_bypass
+     * SPI address 0x09 = PLL bypass
+     * bit 0 = PLL bypass
+     *
+     * Register 2610_0020	reg_hkspi_pll_source
+     * SPI address 0x11 = PLL source
+     * bits 0-2 = phase 0 divider, bits 3-5 = phase 90 divider
+     *
+     * Register 2610_0024	reg_hkspi_pll_divider
+     * SPI address 0x12 = PLL divider
+     * bits 0-4 = feedback divider
+     *
+     * Register 2620_0004	reg_clk_out_dest
+     * SPI address 0x1b = Output redirect
+     * bit 0 = trap to mprj_io[13]
+     * bit 1 = clk  to mprj_io[14]
+     * bit 2 = clk2 to mprj_io[15]
+     *-------------------------------------------------------------
+     */
+
+    // Monitor the core clock and user clock on mprj_io[14] and mprj_io[15]
+    // reg_clk_out_dest = 0x6 to turn on, 0x0 to turn off
+
+    // Write checkpoint for clock counting (PLL bypassed)
     reg_mprj_datal = 0xA0400000;
-
+    reg_clk_out_dest = 0x6;
-    // Enable SPI master
+    reg_clk_out_dest = 0x0;
-    // SPI master configuration bits:
-    // bits 7-0:	Clock prescaler value (default 2)
-    // bit  8:		MSB/LSB first (0 = MSB first, 1 = LSB first)
-    // bit  9:		CSB sense (0 = inverted, 1 = noninverted)
-    // bit 10:		SCK sense (0 = noninverted, 1 = inverted)
-    // bit 11:		mode (0 = read/write opposite edges, 1 = same edges)
-    // bit 12:		stream (1 = CSB ends transmission)
-    // bit 13:		enable (1 = enabled)
-    // bit 14:		IRQ enable (1 = enabled)
-    // bit 15:		Connect to housekeeping SPI (1 = connected)
-
-    reg_spimaster_config = 0xa002;	// Enable, prescaler = 2,
-					// connect to housekeeping SPI
-
-    // Apply stream read (0x40 + 0x03) and read back one byte 
-
-    reg_spimaster_config = 0xb002;	// Apply stream mode
-    reg_spimaster_data = 0x80;		// Write 0x80 (write mode)
-    reg_spimaster_data = 0x08;		// Write 0x18 (start address)
-    reg_spimaster_data = 0x01;		// Write 0x01 to PLL enable, no DCO mode
-    reg_spimaster_config = 0xa102;	// Release CSB (ends stream mode)
-
-    reg_spimaster_config = 0xb002;	// Apply stream mode
-    reg_spimaster_data = 0x80;		// Write 0x80 (write mode)
-    reg_spimaster_data = 0x11;		// Write 0x11 (start address)
-    reg_spimaster_data = 0x03;		// Write 0x03 to PLL output divider
-    reg_spimaster_config = 0xa102;	// Release CSB (ends stream mode)
-
-    reg_spimaster_config = 0xb002;	// Apply stream mode
-    reg_spimaster_data = 0x80;		// Write 0x80 (write mode)
-    reg_spimaster_data = 0x09;		// Write 0x09 (start address)
-    reg_spimaster_data = 0x00;		// Write 0x00 to clock from PLL (no bypass)
-    reg_spimaster_config = 0xa102;	// Release CSB (ends stream mode)
-
-    // Write checkpoint
     reg_mprj_datal = 0xA0410000;
 
-    reg_spimaster_config = 0xb002;	// Apply stream mode
+    // Set PLL enable, no DCO mode
-    reg_spimaster_data = 0x80;		// Write 0x80 (write mode)
+    reg_hkspi_pll_ena = 0x1; 
-    reg_spimaster_data = 0x12;		// Write 0x12 (start address)
+
-    reg_spimaster_data = 0x03;		// Write 0x03 to feedback divider (was 0x04)
+    // Set PLL output divider to 0x03
-    reg_spimaster_config = 0xa102;	// Release CSB (ends stream mode)
+    reg_hkspi_pll_source = 0x3;
+
+    // Write checkpoint for clock counting (PLL bypassed)
+    reg_mprj_datal = 0xA0420000;
+    reg_clk_out_dest = 0x6;
+    reg_clk_out_dest = 0x0;
+    reg_mprj_datal = 0xA0430000;
+
+    // Disable PLL bypass
+    reg_hkspi_pll_bypass = 0x0;
+
+    // Write checkpoint for clock counting
+    reg_mprj_datal = 0xA0440000;
+    reg_clk_out_dest = 0x6;
+    reg_clk_out_dest = 0x0;
+    reg_mprj_datal = 0xA0450000;
+
+    // Write 0x03 to feedback divider (was 0x04)
+    reg_hkspi_pll_divider = 0x3;
 
     // Write checkpoint
-    reg_mprj_datal = 0xA0420000;
+    reg_mprj_datal = 0xA0460000;
+    reg_clk_out_dest = 0x6;
+    reg_clk_out_dest = 0x0;
+    reg_mprj_datal = 0xA0470000;
 
-    reg_spimaster_config = 0xb002;	// Apply stream mode
+    // Write 0x04 to PLL output divider
-    reg_spimaster_data = 0x80;		// Write 0x80 (write mode)
+    reg_hkspi_pll_source = 0x4;
-    reg_spimaster_data = 0x11;		// Write 0x11 (start address)
-    reg_spimaster_data = 0x04;		// Write 0x04 to PLL output divider
-    reg_spimaster_config = 0xa102;	// Release CSB (ends stream mode)
 
-    reg_spimaster_config = 0x2102;	// Release housekeeping SPI
+    // Write checkpoint
+    reg_mprj_datal = 0xA0480000;
+    reg_clk_out_dest = 0x6;
+    reg_clk_out_dest = 0x0;
+    reg_mprj_datal = 0xA0490000;
 
     // End test
     reg_mprj_datal = 0xA0900000;

verilog/dv/caravel/mgmt_soc/pll/pll_tb.v

@@ -37,6 +37,9 @@ module pll_tb;
 	wire flash_io1;
 	wire SDO;
 
+	integer ccount;
+	integer ucount;
+
 	assign checkbits = mprj_io[31:16];
 	assign spivalue  = mprj_io[15:8];
 
@@ -46,6 +49,16 @@ module pll_tb;
 
 	always #10 clock <= (clock === 1'b0);
 
+	// User clock monitoring
+	always @(posedge mprj_io[15]) begin
+	    ucount = ucount + 1;
+	end
+
+	// Core clock monitoring
+	always @(posedge mprj_io[14]) begin
+	    ccount = ccount + 1;
+	end
+
 	initial begin
 		clock = 0;
 	end
@@ -66,21 +79,59 @@ module pll_tb;
 	// Monitor
 	initial begin
 	    wait(checkbits == 16'hA040);
-		
+	    $display("Monitor: Test 1 PLL (RTL) Started");
-		$display("Monitor: Test PLL (RTL) Started");
+	    ucount = 0;
-		
+	    ccount = 0;
 	    wait(checkbits == 16'hA041);
-            // $display("   SPI value = 0x%x (should be 0x04)", spivalue);
+	    $display("Monitor: ucount = %d ccount = %d", ucount, ccount);
-            // if(spivalue !== 32'h04) begin
+            if (ucount !== 129 || ccount != 129) begin
-            //     $display("Monitor: Test PLL (RTL) Failed");
+                $display("Monitor: Test PLL Failed");
-            //     $finish;
+                $finish;
-            // end
+            end
+		
 	    wait(checkbits == 16'hA042);
-            // $display("   SPI value = 0x%x (should be 0x56)", spivalue);
+	    $display("Monitor: Test 2 PLL (RTL) Started");
-            // if(spivalue !== 32'h56) begin
+	    ucount = 0;
-            //     $display("Monitor: Test PLL (RTL) Failed");
+	    ccount = 0;
-            //     $finish;
+	    wait(checkbits == 16'hA043);
-            // end
+	    $display("Monitor: ucount = %d ccount = %d", ucount, ccount);
+            if (ucount !== 193 || ccount != 193) begin
+                $display("Monitor: Test PLL Failed");
+                $finish;
+            end
+
+	    wait(checkbits == 16'hA044);
+	    $display("Monitor: Test 3 PLL (RTL) Started");
+	    ucount = 0;
+	    ccount = 0;
+	    wait(checkbits == 16'hA045);
+	    $display("Monitor: ucount = %d ccount = %d", ucount, ccount);
+            if (ucount !== 385 || ccount != 129) begin
+                $display("Monitor: Test PLL Failed");
+                $finish;
+            end
+
+	    wait(checkbits == 16'hA046);
+	    $display("Monitor: Test 4 PLL (RTL) Started");
+	    ucount = 0;
+	    ccount = 0;
+	    wait(checkbits == 16'hA047);
+	    $display("Monitor: ucount = %d ccount = %d", ucount, ccount);
+            if (ucount !== 385 || ccount != 129) begin
+                $display("Monitor: Test PLL Failed");
+                $finish;
+            end
+
+	    wait(checkbits == 16'hA048);
+	    $display("Monitor: Test 5 PLL (RTL) Started");
+	    ucount = 0;
+	    ccount = 0;
+	    wait(checkbits == 16'hA049);
+	    $display("Monitor: ucount = %d ccount = %d", ucount, ccount);
+            if (ucount !== 513 || ccount != 129) begin
+                $display("Monitor: Test PLL Failed");
+                $finish;
+            end
 
 	    wait(checkbits == 16'hA090);
 

verilog/dv/caravel/mgmt_soc/sysctrl/sysctrl.c

@@ -20,39 +20,23 @@
 // --------------------------------------------------------
 
 /*
- *	System Control Test
+ *	System control test
- *	- Enables SPI master
+ *      - Sets GPIO to monitor the core and user clocks
- *	- Uses SPI master to internally access the housekeeping SPI
+ *
- *      - Reads default value of SPI-Controlled registers
+ *	This test is basically just the first part of the
- *      - Flags failure/success using mprj_io
+ *	PLL test, with the PLL bypassed.  Unlike the PLL
+ *	test, it can be run on a gate-level netlist.
+ *
  */
 void main()
 {
     int i;
-    uint32_t value;
-
-    // Force housekeeping SPI into a disabled state so that the CSB
-    // pin can be used as an output without the system failing
-
-    reg_hkspi_disable = 1;
 
     reg_mprj_datal = 0;
 
-    // Configure upper 6 bits of user GPIO for generating testbench
+    // Configure upper 16 bits of user GPIO for generating testbench
     // checkpoints.
 
-    reg_mprj_io_37 = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_36 = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_35 = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_34 = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_33 = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_32 = GPIO_MODE_MGMT_STD_OUTPUT;
-
-    // Configure all lower 32 bits for writing the SPI value read on GPIO
-    // NOTE:  Converting reg_mprj_io_3 (CSB) to output will disable the
-    // SPI.  But that should not disable the back-door access to the SPI
-    // register values!
-
     reg_mprj_io_31 = GPIO_MODE_MGMT_STD_OUTPUT;
     reg_mprj_io_30 = GPIO_MODE_MGMT_STD_OUTPUT;
     reg_mprj_io_29 = GPIO_MODE_MGMT_STD_OUTPUT;
@@ -70,71 +54,48 @@ void main()
     reg_mprj_io_17 = GPIO_MODE_MGMT_STD_OUTPUT;
     reg_mprj_io_16 = GPIO_MODE_MGMT_STD_OUTPUT;
 
+    /* Monitor pins must be set to output */
     reg_mprj_io_15 = GPIO_MODE_MGMT_STD_OUTPUT;
     reg_mprj_io_14 = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_13 = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_12 = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_11 = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_10 = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_9  = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_8  = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_7  = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_6  = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_5  = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_4  = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_3  = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_2  = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_1  = GPIO_MODE_MGMT_STD_OUTPUT;
-    reg_mprj_io_0  = GPIO_MODE_MGMT_STD_OUTPUT;
 
     /* Apply configuration */
     reg_mprj_xfer = 1;
     while (reg_mprj_xfer == 1);
 
     // Start test
-    reg_mprj_datah = 0x04;
 
-    // Read manufacturer and product ID
+    /*
-    value = reg_hkspi_chip_id;
+     *-------------------------------------------------------------
-    reg_mprj_datal = value;	// Mfgr + product ID
+     * Register 2620_0004	reg_clk_out_dest
-    reg_mprj_datah = 0x05;
+     * SPI address 0x1b = Output redirect
+     * bit 0 = trap to mprj_io[13]
+     * bit 1 = clk  to mprj_io[14]
+     * bit 2 = clk2 to mprj_io[15]
+     *-------------------------------------------------------------
+     */
 
-    // Read user ID
+    // Monitor the core clock and user clock on mprj_io[14] and mprj_io[15]
-    value = reg_hkspi_user_id;
+    // reg_clk_out_dest = 0x6 to turn on, 0x0 to turn off
-    reg_mprj_datal = value;	// User ID
-    reg_mprj_datah = 0x06;
 
-    // Read PLL enables
+    // Write checkpoint for making sure nothing is counted when monitoring is off
-    value = reg_hkspi_pll_ena;
+    reg_mprj_datal = 0xA0400000;
-    reg_mprj_datal = value;	// DLL enables
+    reg_clk_out_dest = 0x0;
-    reg_mprj_datah = 0x07;
+    reg_clk_out_dest = 0x0;
+    reg_mprj_datal = 0xA0410000;
 
-    // Read PLL bypass state
+    // Write checkpoint for core clock counting (PLL bypassed)
-    value = reg_hkspi_pll_bypass;
+    reg_mprj_datal = 0xA0420000;
-    reg_mprj_datal = value;	// DLL bypass state
+    reg_clk_out_dest = 0x2;
-    reg_mprj_datah = 0x08;
+    reg_clk_out_dest = 0x0;
+    reg_mprj_datal = 0xA0430000;
 
-    // Read PLL trim
+    // Write checkpoint for user clock counting (PLL bypassed)
-    value = reg_hkspi_pll_trim;
+    reg_mprj_datal = 0xA0440000;
-    reg_mprj_datal = value;	// DLL trim
+    reg_clk_out_dest = 0x4;
-    reg_mprj_datah = 0x09;
+    reg_clk_out_dest = 0x0;
-
+    reg_mprj_datal = 0xA0450000;
-    // Read PLL source
-    value = reg_hkspi_pll_source;
-    reg_mprj_datal = value;	// DLL source
-    reg_mprj_datah = 0x0a;
-
-    // Read PLL divider
-    value = reg_hkspi_pll_divider;
-    reg_mprj_datal = value;	// DLL divider
-    reg_mprj_datah = 0x0b;
-
-    // Read a GPIO configuration word
-    value = reg_mprj_io_6;
-    reg_mprj_datal = value;	// DLL divider
-    reg_mprj_datah = 0x0c;
 
     // End test
-    reg_mprj_datah = 0x0d;
+    reg_mprj_datal = 0xA0900000;
 }
 

verilog/dv/caravel/mgmt_soc/sysctrl/sysctrl_tb.v

@@ -23,13 +23,13 @@
 
 module sysctrl_tb;
 	reg clock;
+	reg power1;
+	reg power2;
 	reg RSTB;
-	reg csb_set;
-	reg power1, power2;
 
 	wire gpio;
-	wire [5:0] checkbits;
+	wire [15:0] checkbits;
-	wire [31:0] spivalue;
+	wire [7:0] spivalue;
 	wire [37:0] mprj_io;
 	wire flash_csb;
 	wire flash_clk;
@@ -37,11 +37,11 @@ module sysctrl_tb;
 	wire flash_io1;
 	wire SDO;
 
-	assign checkbits = mprj_io[37:32];
+	integer ccount;
-	assign spivalue  = mprj_io[31:0];
+	integer ucount;
 
-	// mrpj_io[3] = CSB needs to be set until the program disables the SPI.
+	assign checkbits = mprj_io[31:16];
-	assign mprj_io[3] = (csb_set) ? 1'b1 : 1'bz;
+	assign spivalue  = mprj_io[15:8];
 
 	// External clock is used by default.  Make this artificially fast for the
 	// simulation.  Normally this would be a slow clock and the digital PLL
@@ -49,6 +49,16 @@ module sysctrl_tb;
 
 	always #10 clock <= (clock === 1'b0);
 
+	// User clock monitoring
+	always @(posedge mprj_io[15]) begin
+	    ucount = ucount + 1;
+	end
+
+	// Core clock monitoring
+	always @(posedge mprj_io[14]) begin
+	    ccount = ccount + 1;
+	end
+
 	initial begin
 		clock = 0;
 	end
@@ -61,79 +71,49 @@ module sysctrl_tb;
 			$display("+1000 cycles");
 		end
 		$display("%c[1;31m",27);
-		`ifdef GL
-			$display ("Monitor: Timeout, Test Sysctrl (GL) Failed");
-		`else
 		$display ("Monitor: Timeout, Test Sysctrl (RTL) Failed");
-		`endif
 		$display("%c[0m",27);
 		$finish;
 	end
 
 	// Monitor
 	initial begin
-	    wait(checkbits == 6'h04);
+	    wait(checkbits == 16'hA040);
-			`ifdef GL
+	    $display("Monitor: Test 1 Sysctrl (RTL) Started");
-            	$display("Monitor: Test Sysctrl (GL) Started");
+	    ucount = 0;
-			`else
+	    ccount = 0;
-			    $display("Monitor: Test Sysctrl (RTL) Started");
+	    wait(checkbits == 16'hA041);
-			`endif
+	    $display("Monitor: ucount = %d ccount = %d", ucount, ccount);
-	    wait(checkbits == 6'h05);
+            if (ucount !== 0 || ccount != 0) begin
-            $display("   Chip ID value = 0x%x (should be 0x00045611)", spivalue);
-            if(spivalue !== 32'h00045611) begin
-                $display("Monitor: Test Sysctrl Failed");
-                $finish;
-            end
-	    wait(checkbits == 6'h06);
-            $display("   User ID value = 0x%x (should be 0x00000000)", spivalue);
-            if(spivalue !== 32'h00000000) begin
-                $display("Monitor: Test Sysctrl Failed");
-                $finish;
-            end
-	    wait(checkbits == 6'h07);
-            $display("   PLL enables value = 0x%x (should be 0x00000002)", spivalue);
-            if(spivalue !== 32'h00000002) begin
-                $display("Monitor: Test Sysctrl Failed");
-                $finish;
-            end
-	    wait(checkbits == 6'h08);
-            $display("   PLL bypass value = 0x%x (should be 0x00000001)", spivalue);
-            if(spivalue !== 32'h00000001) begin
-                $display("Monitor: Test Sysctrl Failed");
-                $finish;
-            end
-	    wait(checkbits == 6'h09);
-            $display("   PLL trim value = 0x%x (should be 0x03ffefff)", spivalue);
-            if(spivalue !== 32'h03ffefff) begin
-                $display("Monitor: Test Sysctrl Failed");
-                $finish;
-            end
-	    wait(checkbits == 6'h0a);
-            $display("   PLL divider value = 0x%x (should be 0x00000012)", spivalue);
-            if(spivalue !== 32'h00000012) begin
-                $display("Monitor: Test Sysctrl Failed");
-                $finish;
-            end
-	    wait(checkbits == 6'h0b);
-            $display("   PLL source value = 0x%x (should be 0x00000004)", spivalue);
-            if(spivalue !== 32'h00000004) begin
-                $display("Monitor: Test Sysctrl Failed");
-                $finish;
-            end
-	    wait(checkbits == 6'h0c);
-            $display("   GPIO config value = 0x%x (should be 0x00001809)", spivalue);
-            if(spivalue !== 32'h00001809) begin
                 $display("Monitor: Test Sysctrl Failed");
                 $finish;
             end
 		
+	    wait(checkbits == 16'hA042);
+	    $display("Monitor: Test 1 Sysctrl (RTL) Started");
+	    ucount = 0;
+	    ccount = 0;
+	    wait(checkbits == 16'hA043);
+	    $display("Monitor: ucount = %d ccount = %d", ucount, ccount);
+            if (ucount !== 129 || ccount != 0) begin
+                $display("Monitor: Test Sysctrl Failed");
+                $finish;
+            end
+		
+	    wait(checkbits == 16'hA044);
+	    $display("Monitor: Test 2 Sysctrl (RTL) Started");
+	    ucount = 0;
+	    ccount = 0;
+	    wait(checkbits == 16'hA045);
+	    $display("Monitor: ucount = %d ccount = %d", ucount, ccount);
+            if (ucount !== 0 || ccount != 129) begin
+                $display("Monitor: Test Sysctrl Failed");
+                $finish;
+            end
+
+	    wait(checkbits == 16'hA090);
 
-	    wait(checkbits == 6'h0d);
-		 	`ifdef GL
-            	$display("Monitor: Test Sysctrl (GL) Passed");
-			`else
 	    $display("Monitor: Test Sysctrl (RTL) Passed");
-			`endif
 	    $finish;
 	end
 
@@ -144,16 +124,13 @@ module sysctrl_tb;
 		#2000;
 	end
 
-	initial begin		// Power-up sequence
+	initial begin
 		power1 <= 1'b0;
 		power2 <= 1'b0;
-		csb_set <= 1'b1;
 		#200;
 		power1 <= 1'b1;
 		#200;
 		power2 <= 1'b1;
-		#200000;
-		csb_set <= 1'b0;	// Release CSB after SPI is disabled
 	end
 
 	always @(checkbits) begin
@@ -168,21 +145,18 @@ module sysctrl_tb;
 	assign VDD1V8 = power2;
 	assign VSS = 1'b0;
 
+	assign mprj_io[3] = 1'b1;  // Force CSB high.
 
 	caravel uut (
 		.vddio	  (VDD3V3),
-		.vddio_2  (VDD3V3),
 		.vssio	  (VSS),
-		.vssio_2  (VSS),
 		.vdda	  (VDD3V3),
 		.vssa	  (VSS),
 		.vccd	  (VDD1V8),
 		.vssd	  (VSS),
 		.vdda1    (VDD3V3),
-		.vdda1_2  (VDD3V3),
 		.vdda2    (VDD3V3),
 		.vssa1	  (VSS),
-		.vssa1_2  (VSS),
 		.vssa2	  (VSS),
 		.vccd1	  (VDD1V8),
 		.vccd2	  (VDD1V8),

verilog/gl/caravan.v

@@ -3841,7 +3841,7 @@ module caravan(vddio, vddio_2, vssio, vssio_2, vdda, vssa, vccd, vssd, vdda1, vd
     .sram_ro_data({ \hkspi_sram_data[31] , \hkspi_sram_data[30] , \hkspi_sram_data[29] , \hkspi_sram_data[28] , \hkspi_sram_data[27] , \hkspi_sram_data[26] , \hkspi_sram_data[25] , \hkspi_sram_data[24] , \hkspi_sram_data[23] , \hkspi_sram_data[22] , \hkspi_sram_data[21] , \hkspi_sram_data[20] , \hkspi_sram_data[19] , \hkspi_sram_data[18] , \hkspi_sram_data[17] , \hkspi_sram_data[16] , \hkspi_sram_data[15] , \hkspi_sram_data[14] , \hkspi_sram_data[13] , \hkspi_sram_data[12] , \hkspi_sram_data[11] , \hkspi_sram_data[10] , \hkspi_sram_data[9] , \hkspi_sram_data[8] , \hkspi_sram_data[7] , \hkspi_sram_data[6] , \hkspi_sram_data[5] , \hkspi_sram_data[4] , \hkspi_sram_data[3] , \hkspi_sram_data[2] , \hkspi_sram_data[1] , \hkspi_sram_data[0]  }),
     .trap(trap),
     .uart_enabled(uart_enabled),
-    .user_clock(mprj_clock2),
+    .user_clock(caravel_clk2),
     .usr1_vcc_pwrgood(mprj_vcc_pwrgood),
     .usr1_vdd_pwrgood(mprj_vdd_pwrgood),
     .usr2_vcc_pwrgood(mprj2_vcc_pwrgood),

verilog/gl/caravel.v

@@ -4579,7 +4579,7 @@ module caravel(vddio, vddio_2, vssio, vssio_2, vdda, vssa, vccd, vssd, vdda1, vd
     .sram_ro_data({ \hkspi_sram_data[31] , \hkspi_sram_data[30] , \hkspi_sram_data[29] , \hkspi_sram_data[28] , \hkspi_sram_data[27] , \hkspi_sram_data[26] , \hkspi_sram_data[25] , \hkspi_sram_data[24] , \hkspi_sram_data[23] , \hkspi_sram_data[22] , \hkspi_sram_data[21] , \hkspi_sram_data[20] , \hkspi_sram_data[19] , \hkspi_sram_data[18] , \hkspi_sram_data[17] , \hkspi_sram_data[16] , \hkspi_sram_data[15] , \hkspi_sram_data[14] , \hkspi_sram_data[13] , \hkspi_sram_data[12] , \hkspi_sram_data[11] , \hkspi_sram_data[10] , \hkspi_sram_data[9] , \hkspi_sram_data[8] , \hkspi_sram_data[7] , \hkspi_sram_data[6] , \hkspi_sram_data[5] , \hkspi_sram_data[4] , \hkspi_sram_data[3] , \hkspi_sram_data[2] , \hkspi_sram_data[1] , \hkspi_sram_data[0]  }),
     .trap(trap),
     .uart_enabled(uart_enabled),
-    .user_clock(mprj_clock2),
+    .user_clock(caravel_clk2),
     .usr1_vcc_pwrgood(mprj_vcc_pwrgood),
     .usr1_vdd_pwrgood(mprj_vdd_pwrgood),
     .usr2_vcc_pwrgood(mprj2_vcc_pwrgood),

verilog/rtl/caravan.v

@@ -767,7 +767,7 @@ module caravan (
 
 	.trap(trap),
 
-	.user_clock(mprj_clock2),
+	.user_clock(caravel_clk2),
 
 	.mask_rev_in(mask_rev),
 

verilog/rtl/caravel.v

@@ -1,4 +1,6 @@
-// `default_nettype none
+ `ifdef SIM
+ `default_nettype wire
+ `endif
 // SPDX-FileCopyrightText: 2020 Efabless Corporation
 //
 // Licensed under the Apache License, Version 2.0 (the "License");
@@ -710,7 +712,7 @@ module caravel (
 
         .trap(trap),
 
-	.user_clock(mprj_clock2),
+	.user_clock(caravel_clk2),
 
         .mask_rev_in(mask_rev),
 

verilog/rtl/caravel_netlists.v

@@ -48,6 +48,8 @@
 
     `ifdef GL
 	`include "gl/digital_pll.v"
+	`include "gl/digital_pll_controller.v"
+	`include "gl/ring_osc2x13.v"
 	`include "gl/caravel_clocking.v"
 	`include "gl/user_id_programming.v"
 	`include "gl/chip_io.v"
@@ -67,6 +69,8 @@
 	`include "gl/caravel.v"
     `else
 	`include "digital_pll.v"
+	`include "digital_pll_controller.v"
+	`include "ring_osc2x13.v"
 	`include "caravel_clocking.v"
 	`include "user_id_programming.v"
 	`include "clock_div.v"

verilog/rtl/chip_io.v

@@ -126,74 +126,58 @@ module chip_io(
 
     	sky130_ef_io__vddio_hvc_clamped_pad \mgmt_vddio_hvclamp_pad[0]  (
 		`MGMT_ABUTMENT_PINS
-`ifdef TOP_ROUTING
+`ifndef TOP_ROUTING
-		.VDDIO(vddio)
+		.VDDIO_PAD(vddio_pad)
-`else 
-		,.VDDIO_PAD(vddio_pad)
 `endif
     	);
 
 	// lies in user area 2
     	sky130_ef_io__vddio_hvc_clamped_pad \mgmt_vddio_hvclamp_pad[1]  (
 		`USER2_ABUTMENT_PINS
-`ifdef TOP_ROUTING
+`ifndef TOP_ROUTING
-		.VDDIO(vddio)
+		.VDDIO_PAD(vddio_pad2)
-`else 
-		,.VDDIO_PAD(vddio_pad2)
 `endif
     	);
 
     	sky130_ef_io__vdda_hvc_clamped_pad mgmt_vdda_hvclamp_pad (
 		`MGMT_ABUTMENT_PINS
-`ifdef TOP_ROUTING
+`ifndef TOP_ROUTING
-		.VDDA(vdda)
+		.VDDA_PAD(vdda_pad)
-`else 
-		,.VDDA_PAD(vdda_pad)
 `endif
     	);
 
     	sky130_ef_io__vccd_lvc_clamped_pad mgmt_vccd_lvclamp_pad (
 		`MGMT_ABUTMENT_PINS
-`ifdef TOP_ROUTING
+`ifndef TOP_ROUTING
-		.VCCD(vccd)
+		.VCCD_PAD(vccd_pad)
-`else 
-		,.VCCD_PAD(vccd_pad)
 `endif
     	);
 
     	sky130_ef_io__vssio_hvc_clamped_pad \mgmt_vssio_hvclamp_pad[0]  (
 		`MGMT_ABUTMENT_PINS
-`ifdef TOP_ROUTING
+`ifndef TOP_ROUTING
-		.VSSIO(vssio)
+		.VSSIO_PAD(vssio_pad)
-`else
-		,.VSSIO_PAD(vssio_pad)
 `endif
     	);
 
     	sky130_ef_io__vssio_hvc_clamped_pad \mgmt_vssio_hvclamp_pad[1]  (
 		`USER2_ABUTMENT_PINS
-`ifdef TOP_ROUTING
+`ifndef TOP_ROUTING
-		.VSSIO(vssio)
+		.VSSIO_PAD(vssio_pad2)
-`else
-		,.VSSIO_PAD(vssio_pad2)
 `endif
     	);
 
     	sky130_ef_io__vssa_hvc_clamped_pad mgmt_vssa_hvclamp_pad (
 		`MGMT_ABUTMENT_PINS
-`ifdef TOP_ROUTING
+`ifndef TOP_ROUTING
-		.VSSA(vssa)
+		.VSSA_PAD(vssa_pad)
-`else
-		,.VSSA_PAD(vssa_pad)
 `endif
     	);
 
     	sky130_ef_io__vssd_lvc_clamped_pad mgmt_vssd_lvclamp_pad (
 		`MGMT_ABUTMENT_PINS
-`ifdef TOP_ROUTING
+`ifndef TOP_ROUTING
-		.VSSD(vssd)
+		.VSSD_PAD(vssd_pad)
-`else
-		,.VSSD_PAD(vssd_pad)
 `endif
     	);
 
@@ -202,58 +186,48 @@ module chip_io(
 
     	sky130_ef_io__vdda_hvc_clamped_pad \user1_vdda_hvclamp_pad[0] (
 		`USER1_ABUTMENT_PINS
-`ifdef TOP_ROUTING
+`ifndef TOP_ROUTING
-		.VDDA(vdda1)
+		.VDDA_PAD(vdda1_pad)
-`else
-		,.VDDA_PAD(vdda1_pad)
 `endif
     	);
 
 		sky130_ef_io__vdda_hvc_clamped_pad \user1_vdda_hvclamp_pad[1] (
 		`USER1_ABUTMENT_PINS
-`ifdef TOP_ROUTING
+`ifndef TOP_ROUTING
-		.VDDA(vdda1)
+		.VDDA_PAD(vdda1_pad2)
-`else
-		,.VDDA_PAD(vdda1_pad2)
 `endif
     	);
 
     	sky130_ef_io__vccd_lvc_clamped3_pad user1_vccd_lvclamp_pad (
 		`USER1_ABUTMENT_PINS
-`ifdef TOP_ROUTING
 		.VCCD1(vccd1),
-		.VSSD1(vssd1)
+		.VSSD1(vssd1),
-`else
+`ifndef TOP_ROUTING
-		,.VCCD_PAD(vccd1_pad)
+		.VCCD_PAD(vccd1_pad)
 `endif
     	);
 
     	sky130_ef_io__vssa_hvc_clamped_pad \user1_vssa_hvclamp_pad[0] (
 		`USER1_ABUTMENT_PINS
-`ifdef TOP_ROUTING
+`ifndef TOP_ROUTING
-		.VSSA(vssa1)
+		.VSSA_PAD(vssa1_pad)
-`else
-		,.VSSA_PAD(vssa1_pad)
 `endif
     	);
 
 
     	sky130_ef_io__vssa_hvc_clamped_pad \user1_vssa_hvclamp_pad[1] (
 		`USER1_ABUTMENT_PINS
-`ifdef TOP_ROUTING
+`ifndef TOP_ROUTING
-		.VSSA(vssa1)
+		.VSSA_PAD(vssa1_pad2)
-`else
-		,.VSSA_PAD(vssa1_pad2)
 `endif
     	);
 
     	sky130_ef_io__vssd_lvc_clamped3_pad user1_vssd_lvclamp_pad (
 		`USER1_ABUTMENT_PINS
-`ifdef TOP_ROUTING
 		.VCCD1(vccd1),
-		.VSSD1(vssd1)
+		.VSSD1(vssd1),
-`else
+`ifndef TOP_ROUTING
-		,.VSSD_PAD(vssd1_pad)
+		.VSSD_PAD(vssd1_pad)
 `endif
     	);
 
@@ -262,39 +236,33 @@ module chip_io(
 
     	sky130_ef_io__vdda_hvc_clamped_pad user2_vdda_hvclamp_pad (
 		`USER2_ABUTMENT_PINS
-`ifdef TOP_ROUTING
+`ifndef TOP_ROUTING
-		.VDDA(vdda2)
+		.VDDA_PAD(vdda2_pad)
-`else
-		,.VDDA_PAD(vdda2_pad)
 `endif
     	);
 
     	sky130_ef_io__vccd_lvc_clamped3_pad user2_vccd_lvclamp_pad (
 		`USER2_ABUTMENT_PINS
-`ifdef TOP_ROUTING
 		.VCCD1(vccd2),
-		.VSSD1(vssd2)
+		.VSSD1(vssd2),
-`else
+`ifndef TOP_ROUTING
-		,.VCCD_PAD(vccd2_pad)
+		.VCCD_PAD(vccd2_pad)
 `endif
     	);
 
     	sky130_ef_io__vssa_hvc_clamped_pad user2_vssa_hvclamp_pad (
 		`USER2_ABUTMENT_PINS
-`ifdef TOP_ROUTING
+`ifndef TOP_ROUTING
-		.VSSA(vssa2)
+		.VSSA_PAD(vssa2_pad)
-`else
-		,.VSSA_PAD(vssa2_pad)
 `endif
     	);
 
     	sky130_ef_io__vssd_lvc_clamped3_pad user2_vssd_lvclamp_pad (
 		`USER2_ABUTMENT_PINS
-`ifdef TOP_ROUTING
 		.VCCD1(vccd2),
-		.VSSD1(vssd2)
+		.VSSD1(vssd2),
-`else
+`ifndef TOP_ROUTING
-		,.VSSD_PAD(vssd2_pad)
+		.VSSD_PAD(vssd2_pad)
 `endif
     	);
 
@@ -328,7 +296,7 @@ module chip_io(
 	sky130_fd_io__top_xres4v2 resetb_pad (
 		`MGMT_ABUTMENT_PINS
 		`ifndef	TOP_ROUTING
-		    ,.PAD(resetb),
+		    .PAD(resetb),
 		`endif
 		.TIE_WEAK_HI_H(xresloop),   // Loop-back connection to pad through pad_a_esd_h
 		.TIE_HI_ESD(),
@@ -361,10 +329,7 @@ module chip_io(
 		.VDDA(vdda),
 		.VCCD(vccd),
 		.VCCHIB(vccd)
-`else
-		.VCCHIB()
 `endif
-
     	    );
 	    sky130_ef_io__corner_pad user1_corner (
 `ifndef TOP_ROUTING
@@ -380,8 +345,6 @@ module chip_io(
 		.VDDA(vdda1),
 		.VCCD(vccd),
 		.VCCHIB(vccd)
-`else
-		.VCCHIB()
 `endif
     	    );
 	    sky130_ef_io__corner_pad user2_corner (
@@ -398,8 +361,6 @@ module chip_io(
 		.VDDA(vdda2),
 		.VCCD(vccd),
 		.VCCHIB(vccd)
-`else
-		.VCCHIB()
 `endif
     	    );
 

verilog/rtl/clock_div.v

@@ -102,9 +102,10 @@ module odd #(
     end
  
     reg [SIZE-1:0] initial_begin;	// this is used to offset the negative edge counter
-    // wire [SIZE:0] interm_3;		// from the positive edge counter in order to
+    wire [SIZE:0] interm_3;		// from the positive edge counter in order to
-    // assign interm_3 = {1'b0,N} + 2'b11;	// guarante 50% duty cycle.
+    assign interm_3 = {1'b0, N} + 2'b11;	// guarantee 50% duty cycle.
-    localparam [SIZE:0] interm_3 = {1'b0,`CLK_DIV} + 2'b11;
+
+    localparam [SIZE:0] interm_init = {1'b0,`CLK_DIV} + 2'b11;
 
     // Counter driven by negative edge of clock.
 
@@ -112,7 +113,7 @@ module odd #(
 	if (resetb == 1'b0) begin
 	    // reset the counter at system reset
 	    counter2 <= `CLK_DIV;
-	    initial_begin <= interm_3[SIZE:1];
+	    initial_begin <= interm_init[SIZE:1];
 	    out_counter2 <= 1;
 	end else if (rst_pulse) begin
 	    // reset the counter at change of N.

verilog/rtl/digital_pll.v

@@ -17,8 +17,10 @@
 // Digital PLL (ring oscillator + controller)
 // Technically this is a frequency locked loop, not a phase locked loop.
 
+`ifndef SIM
 `include "digital_pll_controller.v"
 `include "ring_osc2x13.v"
+`endif
 
 module digital_pll(
 `ifdef USE_POWER_PINS

verilog/rtl/mprj_io.v

@@ -71,7 +71,7 @@ module mprj_io #(
     sky130_ef_io__gpiov2_pad_wrapped  area1_io_pad [AREA1PADS - 1:0] (
 	`USER1_ABUTMENT_PINS
 	`ifndef	TOP_ROUTING
-	    ,.PAD(io[AREA1PADS - 1:0]),
+	    .PAD(io[AREA1PADS - 1:0]),
 	`endif
 	    .OUT(io_out[AREA1PADS - 1:0]),
 	    .OE_N(oeb[AREA1PADS - 1:0]),
@@ -102,7 +102,7 @@ module mprj_io #(
     sky130_ef_io__gpiov2_pad_wrapped area2_io_pad [TOTAL_PADS - AREA1PADS - 1:0] (
 	`USER2_ABUTMENT_PINS
 	`ifndef	TOP_ROUTING
-	    ,.PAD(io[TOTAL_PADS - 1:AREA1PADS]),
+	    .PAD(io[TOTAL_PADS - 1:AREA1PADS]),
 	`endif
 	    .OUT(io_out[TOTAL_PADS - 1:AREA1PADS]),
 	    .OE_N(oeb[TOTAL_PADS - 1:AREA1PADS]),

verilog/rtl/pads.v

@@ -27,7 +27,7 @@
 	.VCCD(vccd),\
 	.VSSIO(vssio),\
 	.VSSD(vssd),\
-	.VSSIO_Q(vssio_q)
+	.VSSIO_Q(vssio_q),
 
 	`define USER2_ABUTMENT_PINS \
 	.AMUXBUS_A(analog_a),\
@@ -41,7 +41,7 @@
 	.VCCD(vccd),\
 	.VSSIO(vssio),\
 	.VSSD(vssd),\
-	.VSSIO_Q(vssio_q)
+	.VSSIO_Q(vssio_q),
 
 	`define MGMT_ABUTMENT_PINS \
 	.AMUXBUS_A(analog_a),\
@@ -55,7 +55,7 @@
 	.VCCD(vccd),\
 	.VSSIO(vssio),\
 	.VSSD(vssd),\
-	.VSSIO_Q(vssio_q)
+	.VSSIO_Q(vssio_q),
 `else 
 	`define USER1_ABUTMENT_PINS 
 	`define USER2_ABUTMENT_PINS 
@@ -78,7 +78,7 @@
 	sky130_ef_io__gpiov2_pad_wrapped X``_pad ( \
 	`MGMT_ABUTMENT_PINS \
 	`ifndef	TOP_ROUTING \
-		,.PAD(X), \
+		.PAD(X), \
 	`endif	\
 		.OUT(vssd), \
 		.OE_N(vccd), \
@@ -110,7 +110,7 @@
 	sky130_ef_io__gpiov2_pad_wrapped X``_pad ( \
 	`MGMT_ABUTMENT_PINS \
 	`ifndef	TOP_ROUTING \
-		,.PAD(X), \
+		.PAD(X), \
 	`endif \
 		.OUT(Y), \
 		.OE_N(OUT_EN_N), \
@@ -142,7 +142,7 @@
 	sky130_ef_io__gpiov2_pad_wrapped X``_pad ( \
 	`MGMT_ABUTMENT_PINS \
 	`ifndef	TOP_ROUTING \
-		,.PAD(X), \
+		.PAD(X), \
 	`endif \
 		.OUT(Y), \
 		.OE_N(OUT_EN_N), \
@@ -174,7 +174,7 @@
 	sky130_ef_io__gpiov2_pad_wrapped X``_pad ( \
 	`MGMT_ABUTMENT_PINS \
 	`ifndef	TOP_ROUTING \
-		,.PAD(X), \
+		.PAD(X), \
 	`endif	\
 		.OUT(Y_OUT),	\
 		.OE_N(OUT_EN_N), \