mirror of https://github.com/lnis-uofu/SOFA.git
110 lines
5.8 KiB
ReStructuredText
110 lines
5.8 KiB
ReStructuredText
.. _sofa_hd_io_resource:
|
|
|
|
I/O Resources
|
|
-------------
|
|
|
|
DATA I/Os
|
|
^^^^^^^^^
|
|
|
|
The *High-Density* (HD) FPGA IP has 144 data I/O pins as shown in :numref:`fig_sofa_hd_fpga_io_switch`.
|
|
|
|
Among the 144 I/Os,
|
|
|
|
- **29 external I/Os** are accessible through the Caravel SoC's *General-Purpose I/Os* (GPIOs).
|
|
|
|
- **115 internal I/Os** are accessible through the Caravel SOC's logic analyzer and wishbone interfaces, which are controlled by the RISC-V processor. See :ref:`sofa_hd_io_resource_debug` and :ref:`sofa_hd_io_resource_accelerator` for details.
|
|
|
|
.. warning:: For all the unused GPIOs, please set them to **input** mode, so that the FPGA will not output any noise signals to damage other SoC components.
|
|
|
|
.. note:: The connectivity of the 115 internal I/Os can be switched through a GPIO of Caravel SoC. As a result, the FPGA can operate in different modes.
|
|
|
|
.. warning:: The internal I/O pins will drive either Wishbone or the logic analyzer, following the same truth table as mode-switch bit in :numref:`fig_sofa_hd_fpga_io_switch`.
|
|
|
|
.. _fig_sofa_hd_fpga_io_switch:
|
|
|
|
.. figure:: ./figures/sofa_hd_fpga_io_switch.svg
|
|
:scale: 20%
|
|
:alt: I/O arrangement of FPGA IP
|
|
|
|
I/O arrangement of *High-Density* (HD) FPGA IP: switchable between logic analyzer and wishbone bus interface
|
|
|
|
.. _io_resource_sofa_hd_external_io:
|
|
|
|
External I/Os
|
|
~~~~~~~~~~~~~
|
|
|
|
A SOFA HD FPGA IP contains 37 external I/O pins, including 29 data I/Os and 8 control I/Os.
|
|
|
|
Full details are summarized in the following table.
|
|
|
|
.. table:: SOFA HD FPGA I/O usage and sizes
|
|
|
|
+-----------+------------------------------------------------------------------------+-------------+
|
|
| I/O Type | Description | No. of Pins |
|
|
+===========+========================================================================+=============+
|
|
| Data I/O | Datapath I/Os of FPGA fabric | 29 |
|
|
+-----------+------------------------------------------------------------------------+-------------+
|
|
| Clk | Operating clock of FPGA core | 1 |
|
|
+-----------+------------------------------------------------------------------------+-------------+
|
|
| ProgClk | Clock used by configuration protocol to program FPGA fabric | 1 |
|
|
+-----------+------------------------------------------------------------------------+-------------+
|
|
| CCin | Input of configuation protocol to load bitstream | 1 |
|
|
+-----------+------------------------------------------------------------------------+-------------+
|
|
| CCout | Output of configuration protocol to read back bitstream | 1 |
|
|
+-----------+------------------------------------------------------------------------+-------------+
|
|
| TestEn | Activate the test mode of FPGA fabric | 1 |
|
|
+-----------+------------------------------------------------------------------------+-------------+
|
|
| SCin | Input of built-in scan-chain to load data to flip-flops of FPGA fabric | 1 |
|
|
+-----------+------------------------------------------------------------------------+-------------+
|
|
| SCout | Output of built-in scan-chain to read back flip-flops from FPGA fabric | 1 |
|
|
+-----------+------------------------------------------------------------------------+-------------+
|
|
| IO_ISLO_N | Active-low signal to enable I/O datapath isolation from external ports | 1 |
|
|
+-----------+------------------------------------------------------------------------+-------------+
|
|
| Total | | 37 |
|
|
+-----------+------------------------------------------------------------------------+-------------+
|
|
|
|
.. _sofa_hd_io_resource_accelerator:
|
|
|
|
Accelerator Mode
|
|
~~~~~~~~~~~~~~~~
|
|
|
|
When the Wishbone interface is enabled, the FPGA can operate as an accelerator for the RISC-V processor.
|
|
:numref:`fig_sofa_hd_fpga_io_map_wishbone_mode` illustrates the detailed I/O arrangement for the FPGA, where the wishbone bus signals are connected to fixed FPGA I/O locations.
|
|
|
|
.. note:: Not all the 115 internal I/Os are used by the Wishbone interface. Especially, the I/O[21:29] are not connected.
|
|
|
|
.. warning:: The FPGA does not contain a Wishbone slave IP. Users have to implement a soft Wishbone slave when use the FPGA as an accelerator.
|
|
|
|
.. _fig_sofa_hd_fpga_io_map_wishbone_mode:
|
|
|
|
.. figure:: ./figures/sofa_hd_fpga_io_map_wishbone_mode.svg
|
|
:scale: 20%
|
|
:alt: I/O arrangement of FPGA IP when interfacing wishbone bus
|
|
|
|
I/O arrangement of *High-Density* (HD) FPGA IP when interfacing wishbone bus
|
|
|
|
.. _sofa_hd_io_resource_debug:
|
|
|
|
Debug Mode
|
|
~~~~~~~~~~
|
|
|
|
When the logic analyzer interface is enabled, the FPGA can operate in debug mode, whose internal signals can be readback through the registers of the RISC-V processor.
|
|
:numref:`fig_sofa_hd_fpga_io_map_logic_analyzer_mode` illustrates the detailed I/O arrangement for the FPGA, where the logic analyzer signals are connected to fixed FPGA I/O locations.
|
|
|
|
.. note:: The logic analyzer is 128-bit, while 115 bits can drive or be driven by the FPGA I/O. The other 14 bits are connected to internal spots of the FPGA fabric, monitoring critical signal activities of the FPGA in debugging purpose.
|
|
|
|
.. warning:: If the logic analyzer is not used, please configure both the management SoC and the FPGA as follows:
|
|
|
|
- all the I/O directionality is set to **input mode**.
|
|
- all the output ports is pulled down to **logic ``0``**.
|
|
|
|
.. _fig_sofa_hd_fpga_io_map_logic_analyzer_mode:
|
|
|
|
.. figure:: ./figures/sofa_hd_fpga_io_map_logic_analyzer_mode.svg
|
|
:scale: 20%
|
|
:alt: I/O arrangement of FPGA IP when interfacing logic analyzer
|
|
|
|
I/O arrangement of *High-Density* (HD) FPGA IP when interfacing logic analyzer
|
|
|
|
|