mirror of https://github.com/lnis-uofu/SOFA.git
updated to use timing annotation file
This commit is contained in:
Andrew Pond
parent
9ba10b3700
commit
3dcdad3253
|
|
@ -1,5 +1,5 @@
|
|||
<!--
|
||||
Low-cost homogeneous FPGA Architecture.
|
||||
Low-cost homogeneous FPGA Architecture for QLSOFA_HD.
|
||||
|
||||
- Skywater 130 nm technology
|
||||
- General purpose logic block:
|
||||
|
|
@ -204,21 +204,6 @@
|
|||
</fixed_layout>
|
||||
</layout>
|
||||
<device>
|
||||
<!-- VB & JL: Using Ian Kuon's transistor sizing and drive strength data for routing, at 40 nm. Ian used BPTM
|
||||
models. We are modifying the delay values however, to include metal C and R, which allows more architecture
|
||||
experimentation. We are also modifying the relative resistance of PMOS to be 1.8x that of NMOS
|
||||
(vs. Ian's 3x) as 1.8x lines up with Jeff G's data from a 45 nm process (and is more typical of
|
||||
45 nm in general). I'm upping the Rmin_nmos from Ian's just over 6k to nearly 9k, and dropping
|
||||
RminW_pmos from 18k to 16k to hit this 1.8x ratio, while keeping the delays of buffers approximately
|
||||
lined up with Stratix IV.
|
||||
We are using Jeff G.'s capacitance data for 45 nm (in tech/ptm_45nm).
|
||||
Jeff's tables list C in for transistors with widths in multiples of the minimum feature size (45 nm).
|
||||
The minimum contactable transistor is 2.5 * 45 nm, so I need to multiply drive strength sizes in this file
|
||||
by 2.5x when looking up in Jeff's tables.
|
||||
The delay values are lined up with Stratix IV, which has an architecture similar to this
|
||||
proposed FPGA, and which is also 40 nm
|
||||
C_ipin_cblock: input capacitance of a track buffer, which VPR assumes is a single-stage
|
||||
4x minimum drive strength buffer. -->
|
||||
<sizing R_minW_nmos="8926" R_minW_pmos="16067"/>
|
||||
<!-- The grid_logic_tile_area below will be used for all blocks that do not explicitly set their own (non-routing)
|
||||
area; set to 0 since we explicitly set the area of all blocks currently in this architecture file.
|
||||
|
|
@ -232,41 +217,25 @@
|
|||
<connection_block input_switch_name="ipin_cblock"/>
|
||||
</device>
|
||||
<switchlist>
|
||||
<!-- VB: the mux_trans_size and buf_size data below is in minimum width transistor *areas*, assuming the purple
|
||||
book area formula. This means the mux transistors are about 5x minimum drive strength.
|
||||
We assume the first stage of the buffer is 3x min drive strength to be reasonable given the large
|
||||
mux transistors, and this gives a reasonable stage ratio of a bit over 5x to the second stage. We assume
|
||||
the n and p transistors in the first stage are equal-sized to lower the buffer trip point, since it's fed
|
||||
by a pass transistor mux. We can then reverse engineer the buffer second stage to hit the specified
|
||||
buf_size (really buffer area) - 16.2x minimum drive nmos and 1.8*16.2 = 29.2x minimum drive.
|
||||
I then took the data from Jeff G.'s PTM modeling of 45 nm to get the Cin (gate of first stage) and Cout
|
||||
(diff of second stage) listed below. Jeff's models are in tech/ptm_45nm, and are in min feature multiples.
|
||||
The minimum contactable transistor is 2.5 * 45 nm, so I need to multiply the drive strength sizes above by
|
||||
2.5x when looking up in Jeff's tables.
|
||||
Finally, we choose a switch delay (58 ps) that leads to length 4 wires having a delay equal to that of SIV of 126 ps.
|
||||
This also leads to the switch being 46% of the total wire delay, which is reasonable. -->
|
||||
<switch type="mux" name="L1_mux" R="551" Cin=".77e-15" Cout="4e-15" Tdel="58e-12" mux_trans_size="2.630740" buf_size="27.645901"/>
|
||||
<switch type="mux" name="L2_mux" R="551" Cin=".77e-15" Cout="4e-15" Tdel="58e-12" mux_trans_size="2.630740" buf_size="27.645901"/>
|
||||
<switch type="mux" name="L4_mux" R="551" Cin=".77e-15" Cout="4e-15" Tdel="58e-12" mux_trans_size="2.630740" buf_size="27.645901"/>
|
||||
<switch type="mux" name="L1_mux" R="0" Cin="0" Cout="0" Tdel="${L1_SB_MUX_DELAY}" mux_trans_size="2.630740" buf_size="27.645901"/>
|
||||
<switch type="mux" name="L2_mux" R="0" Cin="0" Cout="0" Tdel="${L2_SB_MUX_DELAY}" mux_trans_size="2.630740" buf_size="27.645901"/>
|
||||
<switch type="mux" name="L4_mux" R="0" Cin="0" Cout="0" Tdel="${L4_SB_MUX_DELAY}" mux_trans_size="2.630740" buf_size="27.645901"/>
|
||||
<!--switch ipin_cblock resistance set to yeild for 4x minimum drive strength buffer-->
|
||||
<switch type="mux" name="ipin_cblock" R="2231.5" Cout="0." Cin="1.47e-15" Tdel="7.247000e-11" mux_trans_size="1.222260" buf_size="auto"/>
|
||||
<switch type="mux" name="ipin_cblock" R="0" Cout="0" Cin="0" Tdel="${CB_MUX_DELAY}" mux_trans_size="1.222260" buf_size="auto"/>
|
||||
</switchlist>
|
||||
<segmentlist>
|
||||
<!--- VB & JL: using ITRS metal stack data, 96 nm half pitch wires, which are intermediate metal width/space.
|
||||
With the 96 nm half pitch, such wires would take 60 um of height, vs. a 90 nm high (approximated as square) Stratix IV tile so this seems
|
||||
reasonable. Using a tile length of 90 nm, corresponding to the length of a Stratix IV tile if it were square. -->
|
||||
<!-- GIVE a specific name for the segment! OpenFPGA appreciate that! -->
|
||||
<segment name="L1" freq="0.10" length="1" type="unidir" Rmetal="101" Cmetal="22.5e-15">
|
||||
<segment name="L1" freq="0.10" length="1" type="unidir" Rmetal="${L1_WIRE_R}" Cmetal="${L1_WIRE_C}">
|
||||
<mux name="L1_mux"/>
|
||||
<sb type="pattern">1 1</sb>
|
||||
<cb type="pattern">1</cb>
|
||||
</segment>
|
||||
<segment name="L2" freq="0.10" length="2" type="unidir" Rmetal="101" Cmetal="22.5e-15">
|
||||
<segment name="L2" freq="0.10" length="2" type="unidir" Rmetal="${L2_WIRE_R}" Cmetal="${L2_WIRE_C}">
|
||||
<mux name="L2_mux"/>
|
||||
<sb type="pattern">1 1 1</sb>
|
||||
<cb type="pattern">1 1</cb>
|
||||
</segment>
|
||||
<segment name="L4" freq="0.80" length="4" type="unidir" Rmetal="101" Cmetal="22.5e-15">
|
||||
<segment name="L4" freq="0.80" length="4" type="unidir" Rmetal="${L4_WIRE_R}" Cmetal="${L4_WIRE_C}">
|
||||
<mux name="L4_mux"/>
|
||||
<sb type="pattern">1 1 1 1 1</sb>
|
||||
<cb type="pattern">1 1 1 1</cb>
|
||||
|
|
@ -296,10 +265,10 @@
|
|||
</pb_type>
|
||||
<interconnect>
|
||||
<direct name="outpad" input="io.outpad" output="iopad.outpad">
|
||||
<delay_constant max="1.394e-11" in_port="io.outpad" out_port="iopad.outpad"/>
|
||||
<delay_constant max="${OUTPAD_DELAY}" in_port="io.outpad" out_port="iopad.outpad"/>
|
||||
</direct>
|
||||
<direct name="inpad" input="iopad.inpad" output="io.inpad">
|
||||
<delay_constant max="4.243e-11" in_port="iopad.inpad" out_port="io.inpad"/>
|
||||
<delay_constant max="${INPAD_DELAY}" in_port="iopad.inpad" out_port="io.inpad"/>
|
||||
</direct>
|
||||
</interconnect>
|
||||
</mode>
|
||||
|
|
@ -315,7 +284,7 @@
|
|||
</pb_type>
|
||||
<interconnect>
|
||||
<direct name="inpad" input="inpad.inpad" output="io.inpad">
|
||||
<delay_constant max="4.243e-11" in_port="inpad.inpad" out_port="io.inpad"/>
|
||||
<delay_constant max="${INPAD_DELAY}" in_port="inpad.inpad" out_port="io.inpad"/>
|
||||
</direct>
|
||||
</interconnect>
|
||||
</mode>
|
||||
|
|
@ -325,7 +294,7 @@
|
|||
</pb_type>
|
||||
<interconnect>
|
||||
<direct name="outpad" input="io.outpad" output="outpad.outpad">
|
||||
<delay_constant max="1.394e-11" in_port="io.outpad" out_port="outpad.outpad"/>
|
||||
<delay_constant max="${OUTPAD_DELAY}" in_port="io.outpad" out_port="outpad.outpad"/>
|
||||
</direct>
|
||||
</interconnect>
|
||||
</mode>
|
||||
|
|
@ -430,10 +399,10 @@
|
|||
<input name="reset" num_pins="1"/>
|
||||
<output name="Q" num_pins="1"/>
|
||||
<clock name="clk" num_pins="1"/>
|
||||
<T_setup value="66e-12" port="ff.D" clock="clk"/>
|
||||
<T_setup value="66e-12" port="ff.DI" clock="clk"/>
|
||||
<T_setup value="66e-12" port="ff.reset" clock="clk"/>
|
||||
<T_clock_to_Q max="124e-12" port="ff.Q" clock="clk"/>
|
||||
<T_setup value="${FF_T_SETUP}" port="ff.D" clock="clk"/>
|
||||
<T_setup value="${FF_T_SETUP}" port="ff.DI" clock="clk"/>
|
||||
<T_setup value="${FF_T_SETUP}" port="ff.reset" clock="clk"/>
|
||||
<T_clock_to_Q max="${FF_T_CLK2Q}" port="ff.Q" clock="clk"/>
|
||||
</pb_type>
|
||||
<interconnect>
|
||||
<direct name="direct1" input="fabric.in" output="frac_logic.in"/>
|
||||
|
|
@ -446,22 +415,22 @@
|
|||
<complete name="complete1" input="fabric.clk" output="ff[1:0].clk"/>
|
||||
<complete name="complete2" input="fabric.reset" output="ff[1:0].reset"/>
|
||||
<mux name="mux1" input="frac_logic.out[0:0] fabric.reg_in" output="ff[0:0].D">
|
||||
<delay_constant max="25e-12" in_port="frac_logic.out[0:0]" out_port="ff[0:0].D"/>
|
||||
<delay_constant max="45e-12" in_port="fabric.reg_in" out_port="ff[0:0].D"/>
|
||||
<delay_constant max="${LUT_OUT0_TO_FF_D_DELAY}" in_port="frac_logic.out[0:0]" out_port="ff[0:0].D"/>
|
||||
<delay_constant max="${LUT_OUT0_TO_FF_D_DELAY}" in_port="fabric.reg_in" out_port="ff[0:0].D"/>
|
||||
</mux>
|
||||
<mux name="mux2" input="frac_logic.out[1:1] ff[0:0].Q" output="ff[1:1].D">
|
||||
<delay_constant max="25e-12" in_port="frac_logic.out[1:1]" out_port="ff[1:1].D"/>
|
||||
<delay_constant max="45e-12" in_port="ff[0:0].Q" out_port="ff[1:1].D"/>
|
||||
<delay_constant max="${LUT_OUT1_TO_FF_D_DELAY}" in_port="frac_logic.out[1:1]" out_port="ff[1:1].D"/>
|
||||
<delay_constant max="${LUT_OUT1_TO_FF_D_DELAY}" in_port="ff[0:0].Q" out_port="ff[1:1].D"/>
|
||||
</mux>
|
||||
<mux name="mux3" input="ff[0].Q frac_logic.out[0]" output="fabric.out[0]">
|
||||
<!-- LUT to output is faster than FF to output on a Stratix IV -->
|
||||
<delay_constant max="25e-12" in_port="frac_logic.out[0]" out_port="fabric.out[0]"/>
|
||||
<delay_constant max="45e-12" in_port="ff[0].Q" out_port="fabric.out[0]"/>
|
||||
<delay_constant max="${LUT_OUT0_TO_FLE_OUT_DELAY}" in_port="frac_logic.out[0]" out_port="fabric.out[0]"/>
|
||||
<delay_constant max="${FF0_Q_TO_FLE_OUT_DELAY}" in_port="ff[0].Q" out_port="fabric.out[0]"/>
|
||||
</mux>
|
||||
<mux name="mux4" input="ff[1].Q frac_logic.out[1]" output="fabric.out[1]">
|
||||
<!-- LUT to output is faster than FF to output on a Stratix IV -->
|
||||
<delay_constant max="25e-12" in_port="frac_logic.out[1]" out_port="fabric.out[1]"/>
|
||||
<delay_constant max="45e-12" in_port="ff[1].Q" out_port="fabric.out[1]"/>
|
||||
<delay_constant max="${LUT_OUT1_TO_FLE_OUT_DELAY}" in_port="frac_logic.out[1]" out_port="fabric.out[1]"/>
|
||||
<delay_constant max="${FF1_Q_TO_FLE_OUT_DELAY}" in_port="ff[1].Q" out_port="fabric.out[1]"/>
|
||||
</mux>
|
||||
</interconnect>
|
||||
</pb_type>
|
||||
|
|
@ -494,18 +463,10 @@
|
|||
<input name="in" num_pins="3" port_class="lut_in"/>
|
||||
<output name="out" num_pins="1" port_class="lut_out"/>
|
||||
<!-- LUT timing using delay matrix -->
|
||||
<!-- These are the physical delay inputs on a Stratix IV LUT but because VPR cannot do LUT rebalancing,
|
||||
we instead take the average of these numbers to get more stable results
|
||||
82e-12
|
||||
173e-12
|
||||
261e-12
|
||||
263e-12
|
||||
398e-12
|
||||
-->
|
||||
<delay_matrix type="max" in_port="lut3.in" out_port="lut3.out">
|
||||
235e-12
|
||||
235e-12
|
||||
235e-12
|
||||
${LUT3_DELAY}
|
||||
${LUT3_DELAY}
|
||||
${LUT3_DELAY}
|
||||
</delay_matrix>
|
||||
</pb_type>
|
||||
<!-- Define the flip-flop -->
|
||||
|
|
@ -513,8 +474,8 @@
|
|||
<input name="D" num_pins="1" port_class="D"/>
|
||||
<output name="Q" num_pins="1" port_class="Q"/>
|
||||
<clock name="clk" num_pins="1" port_class="clock"/>
|
||||
<T_setup value="66e-12" port="ff.D" clock="clk"/>
|
||||
<T_clock_to_Q max="124e-12" port="ff.Q" clock="clk"/>
|
||||
<T_setup value="${FF_T_SETUP}" port="ff.D" clock="clk"/>
|
||||
<T_clock_to_Q max="${FF_T_CLK2Q}" port="ff.Q" clock="clk"/>
|
||||
</pb_type>
|
||||
<interconnect>
|
||||
<direct name="direct1" input="ble3.in[2:0]" output="lut3[0:0].in[2:0]"/>
|
||||
|
|
@ -525,8 +486,8 @@
|
|||
<direct name="direct3" input="ble3.clk" output="ff[0:0].clk"/>
|
||||
<mux name="mux1" input="ff[0:0].Q lut3.out[0:0]" output="ble3.out[0:0]">
|
||||
<!-- LUT to output is faster than FF to output on a Stratix IV -->
|
||||
<delay_constant max="25e-12" in_port="lut3.out[0:0]" out_port="ble3.out[0:0]"/>
|
||||
<delay_constant max="45e-12" in_port="ff[0:0].Q" out_port="ble3.out[0:0]"/>
|
||||
<delay_constant max="${LUT3_OUT_TO_FLE_OUT_DELAY}" in_port="lut3.out[0:0]" out_port="ble3.out[0:0]"/>
|
||||
<delay_constant max="${FF1_Q_TO_FLE_OUT_DELAY}" in_port="ff[0:0].Q" out_port="ble3.out[0:0]"/>
|
||||
</mux>
|
||||
</interconnect>
|
||||
</pb_type>
|
||||
|
|
@ -556,20 +517,11 @@
|
|||
<input name="in" num_pins="4" port_class="lut_in"/>
|
||||
<output name="out" num_pins="1" port_class="lut_out"/>
|
||||
<!-- LUT timing using delay matrix -->
|
||||
<!-- These are the physical delay inputs on a Stratix IV LUT but because VPR cannot do LUT rebalancing,
|
||||
we instead take the average of these numbers to get more stable results
|
||||
82e-12
|
||||
173e-12
|
||||
261e-12
|
||||
263e-12
|
||||
398e-12
|
||||
397e-12
|
||||
-->
|
||||
<delay_matrix type="max" in_port="lut4.in" out_port="lut4.out">
|
||||
261e-12
|
||||
261e-12
|
||||
261e-12
|
||||
261e-12
|
||||
${LUT4_DELAY}
|
||||
${LUT4_DELAY}
|
||||
${LUT4_DELAY}
|
||||
${LUT4_DELAY}
|
||||
</delay_matrix>
|
||||
</pb_type>
|
||||
<!-- Define flip-flop -->
|
||||
|
|
@ -577,20 +529,21 @@
|
|||
<input name="D" num_pins="1" port_class="D"/>
|
||||
<output name="Q" num_pins="1" port_class="Q"/>
|
||||
<clock name="clk" num_pins="1" port_class="clock"/>
|
||||
<T_setup value="66e-12" port="ff.D" clock="clk"/>
|
||||
<T_clock_to_Q max="124e-12" port="ff.Q" clock="clk"/>
|
||||
<T_setup value="${FF_T_SETUP}" port="ff.D" clock="clk"/>
|
||||
<T_clock_to_Q max="${FF_T_CLK2Q}" port="ff.Q" clock="clk"/>
|
||||
</pb_type>
|
||||
<interconnect>
|
||||
<direct name="direct1" input="ble4.in" output="lut4[0:0].in"/>
|
||||
<direct name="direct2" input="lut4.out" output="ff.D">
|
||||
<!-- Advanced user option that tells CAD tool to find LUT+FF pairs in netlist -->
|
||||
<pack_pattern name="ble4" in_port="lut4.out" out_port="ff.D"/>
|
||||
<delay_constant max="${LUT_OUT0_TO_FF_D_DELAY}" in_port="lut4.out" out_port="ff.D"/>
|
||||
</direct>
|
||||
<direct name="direct3" input="ble4.clk" output="ff.clk"/>
|
||||
<mux name="mux1" input="ff.Q lut4.out" output="ble4.out">
|
||||
<!-- LUT to output is faster than FF to output on a Stratix IV -->
|
||||
<delay_constant max="25e-12" in_port="lut4.out" out_port="ble4.out"/>
|
||||
<delay_constant max="45e-12" in_port="ff.Q" out_port="ble4.out"/>
|
||||
<delay_constant max="${LUT4_OUT_TO_FLE_OUT_DELAY}" in_port="lut4.out" out_port="ble4.out"/>
|
||||
<delay_constant max="${FF0_Q_TO_FLE_OUT_DELAY}" in_port="ff.Q" out_port="ble4.out"/>
|
||||
</mux>
|
||||
</interconnect>
|
||||
</pb_type>
|
||||
|
|
@ -612,15 +565,23 @@
|
|||
<input name="D" num_pins="1" port_class="D"/>
|
||||
<output name="Q" num_pins="1" port_class="Q"/>
|
||||
<clock name="clk" num_pins="1" port_class="clock"/>
|
||||
<T_setup value="66e-12" port="ff.D" clock="clk"/>
|
||||
<T_clock_to_Q max="124e-12" port="ff.Q" clock="clk"/>
|
||||
<T_setup value="${FF_T_SETUP}" port="ff.D" clock="clk"/>
|
||||
<T_clock_to_Q max="${FF_T_CLK2Q}" port="ff.Q" clock="clk"/>
|
||||
</pb_type>
|
||||
<interconnect>
|
||||
<direct name="direct1" input="shift_reg.reg_in" output="ff[0].D"/>
|
||||
<direct name="direct2" input="ff[0].Q" output="ff[1].D"/>
|
||||
<direct name="direct1" input="shift_reg.reg_in" output="ff[0].D">
|
||||
<delay_constant max="${LUT_OUT0_TO_FF_D_DELAY}" in_port="shift_reg.reg_in" out_port="ff[0].D"/>
|
||||
</direct>
|
||||
<direct name="direct2" input="ff[0].Q" output="ff[1].D">
|
||||
<delay_constant max="${FF0_TO_FF1_DELAY}" in_port="ff[0].Q" out_port="ff[1].D"/>
|
||||
</direct>
|
||||
<direct name="direct3" input="ff[1].Q" output="shift_reg.reg_out"/>
|
||||
<direct name="direct4" input="ff[0].Q" output="shift_reg.ff_out[0:0]"/>
|
||||
<direct name="direct5" input="ff[1].Q" output="shift_reg.ff_out[1:1]"/>
|
||||
<direct name="direct4" input="ff[0].Q" output="shift_reg.ff_out[0:0]">
|
||||
<delay_constant max="${FF0_Q_TO_FLE_OUT_DELAY}" in_port="ff[0].Q" out_port="shift_reg.ff_out[0:0]"/>
|
||||
</direct>
|
||||
<direct name="direct5" input="ff[1].Q" output="shift_reg.ff_out[1:1]">
|
||||
<delay_constant max="${FF1_Q_TO_FLE_OUT_DELAY}" in_port="ff[1].Q" out_port="shift_reg.ff_out[1:1]"/>
|
||||
</direct>
|
||||
<complete name="complete1" input="shift_reg.clk" output="ff.clk"/>
|
||||
</interconnect>
|
||||
</pb_type>
|
||||
|
|
@ -642,52 +603,36 @@
|
|||
I[0] should be connected to in[0]
|
||||
-->
|
||||
<direct name="direct_fle0" input="clb.I0[0:1]" output="fle[0:0].in[0:1]">
|
||||
<!-- TODO: Timing should be backannotated from post-PnR results -->
|
||||
</direct>
|
||||
<direct name="direct_fle0i" input="clb.I0i[0:1]" output="fle[0:0].in[2:3]">
|
||||
<!-- TODO: Timing should be backannotated from post-PnR results -->
|
||||
</direct>
|
||||
<direct name="direct_fle1" input="clb.I1[0:1]" output="fle[1:1].in[0:1]">
|
||||
<!-- TODO: Timing should be backannotated from post-PnR results -->
|
||||
</direct>
|
||||
<direct name="direct_fle1i" input="clb.I1i[0:1]" output="fle[1:1].in[2:3]">
|
||||
<!-- TODO: Timing should be backannotated from post-PnR results -->
|
||||
</direct>
|
||||
<direct name="direct_fle2" input="clb.I2[0:1]" output="fle[2:2].in[0:1]">
|
||||
<!-- TODO: Timing should be backannotated from post-PnR results -->
|
||||
</direct>
|
||||
<direct name="direct_fle2i" input="clb.I2i[0:1]" output="fle[2:2].in[2:3]">
|
||||
<!-- TODO: Timing should be backannotated from post-PnR results -->
|
||||
</direct>
|
||||
<direct name="direct_fle3" input="clb.I3[0:1]" output="fle[3:3].in[0:1]">
|
||||
<!-- TODO: Timing should be backannotated from post-PnR results -->
|
||||
</direct>
|
||||
<direct name="direct_fle3i" input="clb.I3i[0:1]" output="fle[3:3].in[2:3]">
|
||||
<!-- TODO: Timing should be backannotated from post-PnR results -->
|
||||
</direct>
|
||||
<direct name="direct_fle4" input="clb.I4[0:1]" output="fle[4:4].in[0:1]">
|
||||
<!-- TODO: Timing should be backannotated from post-PnR results -->
|
||||
</direct>
|
||||
<direct name="direct_fle4i" input="clb.I4i[0:1]" output="fle[4:4].in[2:3]">
|
||||
<!-- TODO: Timing should be backannotated from post-PnR results -->
|
||||
</direct>
|
||||
<direct name="direct_fle5" input="clb.I5[0:1]" output="fle[5:5].in[0:1]">
|
||||
<!-- TODO: Timing should be backannotated from post-PnR results -->
|
||||
</direct>
|
||||
<direct name="direct_fle5i" input="clb.I5i[0:1]" output="fle[5:5].in[2:3]">
|
||||
<!-- TODO: Timing should be backannotated from post-PnR results -->
|
||||
</direct>
|
||||
<direct name="direct_fle6" input="clb.I6[0:1]" output="fle[6:6].in[0:1]">
|
||||
<!-- TODO: Timing should be backannotated from post-PnR results -->
|
||||
</direct>
|
||||
<direct name="direct_fle6i" input="clb.I6i[0:1]" output="fle[6:6].in[2:3]">
|
||||
<!-- TODO: Timing should be backannotated from post-PnR results -->
|
||||
</direct>
|
||||
<direct name="direct_fle7" input="clb.I7[0:1]" output="fle[7:7].in[0:1]">
|
||||
<!-- TODO: Timing should be backannotated from post-PnR results -->
|
||||
</direct>
|
||||
<direct name="direct_fle7i" input="clb.I7i[0:1]" output="fle[7:7].in[2:3]">
|
||||
<!-- TODO: Timing should be backannotated from post-PnR results -->
|
||||
</direct>
|
||||
<complete name="clks" input="clb.clk" output="fle[7:0].clk">
|
||||
</complete>
|
||||
|
|
@ -703,7 +648,7 @@
|
|||
<!-- Shift register chain links -->
|
||||
<direct name="shift_register_in" input="clb.reg_in" output="fle[0:0].reg_in">
|
||||
<!-- Put all inter-block carry chain delay on this one edge -->
|
||||
<delay_constant max="0.16e-9" in_port="clb.reg_in" out_port="fle[0:0].reg_in"/>
|
||||
<delay_constant max="0" in_port="clb.reg_in" out_port="fle[0:0].reg_in"/>
|
||||
<!--pack_pattern name="chain" in_port="clb.reg_in" out_port="fle[0:0].reg_in"/-->
|
||||
</direct>
|
||||
<direct name="shift_register_out" input="fle[7:7].reg_out" output="clb.reg_out">
|
||||
|
|
@ -715,7 +660,7 @@
|
|||
<!-- Scan chain links -->
|
||||
<direct name="scan_chain_in" input="clb.sc_in" output="fle[0:0].sc_in">
|
||||
<!-- Put all inter-block carry chain delay on this one edge -->
|
||||
<delay_constant max="0.16e-9" in_port="clb.sc_in" out_port="fle[0:0].sc_in"/>
|
||||
<delay_constant max="0" in_port="clb.sc_in" out_port="fle[0:0].sc_in"/>
|
||||
</direct>
|
||||
<direct name="scan_chain_out" input="fle[7:7].sc_out" output="clb.sc_out">
|
||||
</direct>
|
||||
|
|
@ -724,7 +669,7 @@
|
|||
<!-- Carry chain links -->
|
||||
<direct name="carry_chain_in" input="clb.cin" output="fle[0:0].cin">
|
||||
<!-- Put all inter-block carry chain delay on this one edge -->
|
||||
<delay_constant max="0.16e-9" in_port="clb.cin" out_port="fle[0:0].cin"/>
|
||||
<delay_constant max="0" in_port="clb.cin" out_port="fle[0:0].cin"/>
|
||||
</direct>
|
||||
<direct name="carry_chain_out" input="fle[7:7].cout" output="clb.cout">
|
||||
</direct>
|
||||
|
|
|
|||
|
|
@ -14,6 +14,7 @@ spice_output=false
|
|||
verilog_output=true
|
||||
timeout_each_job = 1*60
|
||||
fpga_flow=yosys_vpr
|
||||
arch_variable_file=${SKYWATER_OPENFPGA_HOME}/ARCH/timing_annotation/k4_frac_N8_tileable_register_scan_chain_nonLR_caravel_io_skywater130nm_timing_tt_025C_1v80.yml
|
||||
|
||||
[OpenFPGA_SHELL]
|
||||
openfpga_shell_template=${SKYWATER_OPENFPGA_HOME}/SCRIPT/openfpga_shell_script/skywater_generate_testbench_arch_exploration.openfpga
|
||||
|
|
|
|||
Loading…
Reference in New Issue