From 01fabc65cc2d85cdfc66bc02a1eb05b2f5cbc9b8 Mon Sep 17 00:00:00 2001
From: Tarachand Pagarani <tpagarani@quicklogic.com>
Date: Mon, 21 Dec 2020 07:13:38 -0800
Subject: [PATCH] added a new architecture with LUT4, Soft adder and cross
 local routing with 24 clb inputs and feedback

---
 ...avel_io_skywater130nm_fdhd_cc_openfpga.xml | 261 ++++++++
 ...n_chain_nonLR_caravel_io_skywater130nm.xml | 591 ++++++++++++++++++
 .../generate_fabric/config/task_template.conf |   4 +-
 .../generate_sdc/config/task_template.conf    |   4 +-
 .../config/task_template.conf                 |   8 +-
 5 files changed, 860 insertions(+), 8 deletions(-)
 create mode 100644 ARCH/openfpga_arch_template/k4_N8_reset_softadder_register_scan_chain_caravel_io_skywater130nm_fdhd_cc_openfpga.xml
 create mode 100644 ARCH/vpr_arch/k4_N8_tileable_reset_softadder_register_scan_chain_nonLR_caravel_io_skywater130nm.xml

diff --git a/ARCH/openfpga_arch_template/k4_N8_reset_softadder_register_scan_chain_caravel_io_skywater130nm_fdhd_cc_openfpga.xml b/ARCH/openfpga_arch_template/k4_N8_reset_softadder_register_scan_chain_caravel_io_skywater130nm_fdhd_cc_openfpga.xml
new file mode 100644
index 0000000..b7a2687
--- /dev/null
+++ b/ARCH/openfpga_arch_template/k4_N8_reset_softadder_register_scan_chain_caravel_io_skywater130nm_fdhd_cc_openfpga.xml
@@ -0,0 +1,261 @@
+<!-- Architecture annotation for OpenFPGA framework
+     This annotation supports the k4_frac_cc_sky130nm.xml
+     - General purpose logic block
+       - K = 6, N = 10, I = 40
+       - Single mode
+     - Routing architecture
+       - L = 4, fc_in = 0.15, fc_out = 0.1
+     - Skywater 130nm PDK
+       - circuit models are binded to the opensource skywater
+         foundry middle-speed (ms) standard cell library
+  -->
+<openfpga_architecture>
+  <technology_library>
+    <device_library>
+      <device_model name="logic" type="transistor">
+        <lib type="industry" corner="TOP_TT" ref="M" path="${OPENFPGA_PATH}/openfpga_flow/tech/PTM_45nm/45nm.pm"/>
+        <design vdd="0.9" pn_ratio="2"/>
+        <pmos name="pch" chan_length="40e-9" min_width="140e-9" variation="logic_transistor_var"/>
+        <nmos name="nch" chan_length="40e-9" min_width="140e-9" variation="logic_transistor_var"/>
+      </device_model>
+      <device_model name="io" type="transistor">
+        <lib type="academia" ref="M" path="${OPENFPGA_PATH}/openfpga_flow/tech/PTM_45nm/45nm.pm"/>
+        <design vdd="2.5" pn_ratio="3"/>
+        <pmos name="pch_25" chan_length="270e-9" min_width="320e-9" variation="io_transistor_var"/>
+        <nmos name="nch_25" chan_length="270e-9" min_width="320e-9" variation="io_transistor_var"/>
+      </device_model>
+    </device_library>
+    <variation_library>
+      <variation name="logic_transistor_var" abs_deviation="0.1" num_sigma="3"/>
+      <variation name="io_transistor_var" abs_deviation="0.1" num_sigma="3"/>
+    </variation_library>
+  </technology_library>
+  <circuit_library>
+    <circuit_model type="inv_buf" name="sky130_fd_sc_hd__inv_1" prefix="sky130_fd_sc_hd__inv_1" is_default="true" verilog_netlist="${SKYWATER_OPENFPGA_HOME}/PDK/skywater-pdk/libraries/sky130_fd_sc_hd/latest/cells/inv/sky130_fd_sc_hd__inv_1.v">
+      <design_technology type="cmos" topology="inverter" size="1"/>
+      <device_technology device_model_name="logic"/>
+      <port type="input" prefix="in" lib_name="A" size="1"/>
+      <port type="output" prefix="out" lib_name="Y" size="1"/>
+      <delay_matrix type="rise" in_port="in" out_port="out">
+        10e-12
+      </delay_matrix>
+      <delay_matrix type="fall" in_port="in" out_port="out">
+        10e-12
+      </delay_matrix>
+    </circuit_model>
+    <circuit_model type="inv_buf" name="sky130_fd_sc_hd__buf_2" prefix="sky130_fd_sc_hd__buf_2" is_default="false" verilog_netlist="${SKYWATER_OPENFPGA_HOME}/PDK/skywater-pdk/libraries/sky130_fd_sc_hd/latest/cells/buf/sky130_fd_sc_hd__buf_2.v">
+      <design_technology type="cmos" topology="buffer" size="1" num_level="2" f_per_stage="2"/>
+      <device_technology device_model_name="logic"/>
+      <port type="input" prefix="in" lib_name="A" size="1"/>
+      <port type="output" prefix="out" lib_name="X" size="1"/>
+      <delay_matrix type="rise" in_port="in" out_port="out">
+        10e-12
+      </delay_matrix>
+      <delay_matrix type="fall" in_port="in" out_port="out">
+        10e-12
+      </delay_matrix>
+    </circuit_model>
+    <circuit_model type="inv_buf" name="sky130_fd_sc_hd__buf_4" prefix="sky130_fd_sc_hd__buf_4" is_default="false" verilog_netlist="${SKYWATER_OPENFPGA_HOME}/PDK/skywater-pdk/libraries/sky130_fd_sc_hd/latest/cells/buf/sky130_fd_sc_hd__buf_4.v">
+      <design_technology type="cmos" topology="buffer" size="1" num_level="2" f_per_stage="4"/>
+      <device_technology device_model_name="logic"/>
+      <port type="input" prefix="in" lib_name="A" size="1"/>
+      <port type="output" prefix="out" lib_name="X" size="1"/>
+      <delay_matrix type="rise" in_port="in" out_port="out">
+        10e-12
+      </delay_matrix>
+      <delay_matrix type="fall" in_port="in" out_port="out">
+        10e-12
+      </delay_matrix>
+    </circuit_model>
+    <circuit_model type="inv_buf" name="sky130_fd_sc_hd__inv_2" prefix="sky130_fd_sc_hd__inv_2" is_default="false" verilog_netlist="${SKYWATER_OPENFPGA_HOME}/PDK/skywater-pdk/libraries/sky130_fd_sc_hd/latest/cells/inv/sky130_fd_sc_hd__inv_2.v">
+      <design_technology type="cmos" topology="buffer" size="1"/>
+      <device_technology device_model_name="logic"/>
+      <port type="input" prefix="in" lib_name="A" size="1"/>
+      <port type="output" prefix="out" lib_name="Y" size="1"/>
+      <delay_matrix type="rise" in_port="in" out_port="out">
+        10e-12
+      </delay_matrix>
+      <delay_matrix type="fall" in_port="in" out_port="out">
+        10e-12
+      </delay_matrix>
+    </circuit_model>
+    <circuit_model type="gate" name="sky130_fd_sc_hd__or2_1" prefix="sky130_fd_sc_hd__or2_1" is_default="true" verilog_netlist="${SKYWATER_OPENFPGA_HOME}/PDK/skywater-pdk/libraries/sky130_fd_sc_hd/latest/cells/or2/sky130_fd_sc_hd__or2_1.v">
+      <design_technology type="cmos" topology="OR"/>
+      <device_technology device_model_name="logic"/>
+      <input_buffer exist="false"/>
+      <output_buffer exist="false"/>
+      <port type="input" prefix="a" lib_name="A" size="1"/>
+      <port type="input" prefix="b" lib_name="B" size="1"/>
+      <port type="output" prefix="out" lib_name="X" size="1"/>
+      <delay_matrix type="rise" in_port="a b" out_port="out">
+        10e-12 5e-12
+      </delay_matrix>
+      <delay_matrix type="fall" in_port="a b" out_port="out">
+        10e-12 5e-12
+      </delay_matrix>
+    </circuit_model>
+    <!-- Define a circuit model for the standard cell MUX2
+         OpenFPGA requires the following truth table for the MUX2
+         When the select signal sel is enabled, the first input, i.e., in0
+         will be propagated to the output, i.e., out
+         If your standard cell provider does not offer the exact truth table,
+         you can simply swap the inputs as shown in the example below
+      -->
+    <circuit_model type="gate" name="sky130_fd_sc_hd__mux2_1" prefix="sky130_fd_sc_hd__mux2_1" verilog_netlist="${SKYWATER_OPENFPGA_HOME}/PDK/skywater-pdk/libraries/sky130_fd_sc_hd/latest/cells/mux2/sky130_fd_sc_hd__mux2_1.v">
+      <design_technology type="cmos" topology="MUX2"/>
+      <device_technology device_model_name="logic"/>
+      <input_buffer exist="false"/>
+      <output_buffer exist="false"/>
+      <port type="input" prefix="in0" lib_name="A1" size="1"/>
+      <port type="input" prefix="in1" lib_name="A0" size="1"/>
+      <port type="input" prefix="sel" lib_name="S" size="1"/>
+      <port type="output" prefix="out" lib_name="X" size="1"/>
+    </circuit_model>
+    <circuit_model type="chan_wire" name="chan_segment" prefix="track_seg" is_default="true">
+      <design_technology type="cmos"/>
+      <input_buffer exist="false"/>
+      <output_buffer exist="false"/>
+      <port type="input" prefix="in" size="1"/>
+      <port type="output" prefix="out" size="1"/>
+      <wire_param model_type="pi" R="101" C="22.5e-15" num_level="1"/>
+      <!-- model_type could be T, res_val and cap_val DON'T CARE -->
+    </circuit_model>
+    <circuit_model type="wire" name="direct_interc" prefix="direct_interc" is_default="true">
+      <design_technology type="cmos"/>
+      <input_buffer exist="false"/>
+      <output_buffer exist="false"/>
+      <port type="input" prefix="in" size="1"/>
+      <port type="output" prefix="out" size="1"/>
+      <wire_param model_type="pi" R="0" C="0" num_level="1"/>
+      <!-- model_type could be T, res_val cap_val should be defined -->
+    </circuit_model>
+    <circuit_model type="mux" name="mux_tree" prefix="mux_tree" is_default="true" dump_structural_verilog="true">
+      <design_technology type="cmos" structure="tree" add_const_input="true" const_input_val="1"/>
+      <input_buffer exist="false"/>
+      <output_buffer exist="false"/>
+      <pass_gate_logic circuit_model_name="sky130_fd_sc_hd__mux2_1"/>
+      <port type="input" prefix="in" size="1"/>
+      <port type="output" prefix="out" size="1"/>
+      <port type="sram" prefix="sram" size="1"/>
+    </circuit_model>
+    <circuit_model type="mux" name="mux_tree_tapbuf" prefix="mux_tree_tapbuf" dump_structural_verilog="true">
+      <design_technology type="cmos" structure="tree" add_const_input="true" const_input_val="1"/>
+      <input_buffer exist="false"/>
+      <output_buffer exist="true" circuit_model_name="sky130_fd_sc_hd__buf_4"/>
+      <pass_gate_logic circuit_model_name="sky130_fd_sc_hd__mux2_1"/>
+      <port type="input" prefix="in" size="1"/>
+      <port type="output" prefix="out" size="1"/>
+      <port type="sram" prefix="sram" size="1"/>
+    </circuit_model>
+    <!--DFF subckt ports should be defined as <D> <Q> <CLK> <RESET> <SET>  -->
+    <circuit_model type="ff" name="sky130_fd_sc_hd__sdfrtp_1" prefix="sky130_fd_sc_hd__sdfrtp_1" verilog_netlist="${SKYWATER_OPENFPGA_HOME}/PDK/skywater-pdk/libraries/sky130_fd_sc_hd/latest/cells/sdfrtp/sky130_fd_sc_hd__sdfrtp_1.v">
+      <design_technology type="cmos"/>
+      <input_buffer exist="true" circuit_model_name="sky130_fd_sc_hd__inv_1"/>
+      <output_buffer exist="true" circuit_model_name="sky130_fd_sc_hd__inv_1"/>
+      <port type="input" prefix="D" size="1"/>
+      <port type="input" prefix="DI" lib_name="SCD" size="1"/>
+      <port type="input" prefix="Test_en" lib_name="SCE" size="1" is_global="true" default_val="0"/>
+      <port type="input" prefix="reset" lib_name="RESET_B" size="1" default_val="1"/> 
+      <port type="output" prefix="Q" size="1"/>
+      <port type="clock" prefix="clk" lib_name="CLK" size="1" is_global="false" default_val="0" />
+    </circuit_model>
+    <circuit_model type="lut" name="frac_lut4" prefix="frac_lut4" dump_structural_verilog="true">
+      <design_technology type="cmos" fracturable_lut="true"/>
+      <input_buffer exist="false"/>
+      <output_buffer exist="true" circuit_model_name="sky130_fd_sc_hd__buf_2"/>
+      <lut_input_inverter exist="true" circuit_model_name="sky130_fd_sc_hd__inv_1"/>
+      <lut_input_buffer exist="true" circuit_model_name="sky130_fd_sc_hd__buf_2"/>
+      <lut_intermediate_buffer exist="true" circuit_model_name="sky130_fd_sc_hd__buf_2" location_map="-1-"/>
+      <pass_gate_logic circuit_model_name="sky130_fd_sc_hd__mux2_1"/>
+      <port type="input" prefix="in" size="4" tri_state_map="---1" circuit_model_name="sky130_fd_sc_hd__or2_1"/>
+      <port type="output" prefix="lut2_out" size="2" lut_frac_level="2" lut_output_mask="2,3"/>
+      <port type="output" prefix="lut4_out" size="1" lut_output_mask="0"/>
+      <port type="sram" prefix="sram" size="16"/>
+      <port type="sram" prefix="mode" size="1" mode_select="true" circuit_model_name="sky130_fd_sc_hd__dfrtp_1" default_val="1"/>
+    </circuit_model>
+    <!--Scan-chain DFF subckt ports should be defined as <D> <Q> <Qb> <CLK> <RESET> <SET>  -->
+    <circuit_model type="ccff" name="sky130_fd_sc_hd__dfrtp_1" prefix="sky130_fd_sc_hd__dfrtp_1" verilog_netlist="${SKYWATER_OPENFPGA_HOME}/PDK/skywater-pdk/libraries/sky130_fd_sc_hd/latest/cells/dfrtp/sky130_fd_sc_hd__dfrtp_1.v">
+      <design_technology type="cmos"/>
+      <input_buffer exist="true" circuit_model_name="sky130_fd_sc_hd__inv_1"/>
+      <output_buffer exist="true" circuit_model_name="sky130_fd_sc_hd__inv_1"/>
+      <port type="input" prefix="D" size="1"/>
+      <port type="output" prefix="Q" size="1"/>
+      <port type="clock" prefix="prog_clk" lib_name="CLK" size="1" is_global="true" default_val="0" is_prog="true"/>
+      <port type="input" prefix="pReset" lib_name="RESET_B" size="1" is_global="true" default_val="1" is_prog="true" is_reset="true"/> 
+    </circuit_model>
+    <circuit_model type="iopad" name="EMBEDDED_IO_HD" prefix="EMBEDDED_IO_HD" is_default="true" verilog_netlist="${SKYWATER_OPENFPGA_HOME}/HDL/common/digital_io_hd.v">
+      <design_technology type="cmos"/>
+      <input_buffer exist="true" circuit_model_name="sky130_fd_sc_hd__inv_1"/>
+      <output_buffer exist="true" circuit_model_name="sky130_fd_sc_hd__inv_1"/>
+      <port type="input" prefix="SOC_IN" lib_name="SOC_IN" size="1" is_global="true" is_io="true" is_data_io="true"/>
+      <port type="output" prefix="SOC_OUT" lib_name="SOC_OUT" size="1" is_global="true" is_io="true" is_data_io="true"/>
+      <port type="output" prefix="SOC_DIR" lib_name="SOC_DIR" size="1" is_global="true" is_io="true"/>
+      <port type="input" prefix="IO_ISOL_N" lib_name="IO_ISOL_N" size="1" is_global="true" default_val="1"/>
+      <port type="output" prefix="inpad" lib_name="FPGA_IN" size="1"/>
+      <port type="input" prefix="outpad" lib_name="FPGA_OUT" size="1"/>
+      <port type="sram" prefix="en" lib_name="FPGA_DIR" size="1" mode_select="true" circuit_model_name="sky130_fd_sc_hd__dfrtp_1" default_val="1"/>
+    </circuit_model>
+    <circuit_model type="hard_logic" name="sky130_fd_sc_hd__mux2_1_wrapper" prefix="sky130_fd_sc_hd__mux2_1_wrapper" verilog_netlist="${SKYWATER_OPENFPGA_HOME}/HDL/common/sky130_fd_sc_hd_wrapper.v">
+      <design_technology type="cmos"/>
+      <device_technology device_model_name="logic"/>
+      <input_buffer exist="false"/>
+      <output_buffer exist="false"/>
+      <port type="input" prefix="a" lib_name="A0" size="1"/>
+      <port type="input" prefix="b" lib_name="A1" size="1"/>
+      <port type="input" prefix="cin" lib_name="S" size="1"/>
+      <port type="output" prefix="cout" lib_name="X" size="1"/>
+    </circuit_model>
+  </circuit_library>
+  <configuration_protocol>
+    <organization type="scan_chain" circuit_model_name="sky130_fd_sc_hd__dfrtp_1" num_regions="1"/>
+  </configuration_protocol>
+  <connection_block>
+    <switch name="ipin_cblock" circuit_model_name="mux_tree_tapbuf"/>
+  </connection_block>
+  <switch_block>
+    <switch name="L1_mux" circuit_model_name="mux_tree_tapbuf"/>
+    <switch name="L2_mux" circuit_model_name="mux_tree_tapbuf"/>
+    <switch name="L4_mux" circuit_model_name="mux_tree_tapbuf"/>
+  </switch_block>
+  <routing_segment>
+    <segment name="L1" circuit_model_name="chan_segment"/>
+    <segment name="L2" circuit_model_name="chan_segment"/>
+    <segment name="L4" circuit_model_name="chan_segment"/>
+  </routing_segment>
+  <direct_connection>
+    <direct name="carry_chain" circuit_model_name="direct_interc"/>
+    <direct name="shift_register" circuit_model_name="direct_interc"/>
+    <direct name="scan_chain" circuit_model_name="direct_interc" type="column" x_dir="positive" y_dir="positive"/>
+  </direct_connection>
+  <tile_annotations>
+    <global_port name="clk" tile_port="clb.clk" is_clock="true" default_val="0"/>
+    <global_port name="Reset" tile_port="clb.reset" is_reset="true" default_val="1"/>
+  </tile_annotations>
+  <pb_type_annotations>
+    <!-- physical pb_type binding in complex block IO -->
+    <pb_type name="io" physical_mode_name="physical" idle_mode_name="inpad"/>
+    <!-- IMPORTANT: must set unused I/Os to operating in INPUT mode !!! -->
+    <pb_type name="io[physical].iopad" circuit_model_name="EMBEDDED_IO_HD" mode_bits="1"/> 
+    <pb_type name="io[inpad].inpad" physical_pb_type_name="io[physical].iopad" mode_bits="1"/> 
+    <pb_type name="io[outpad].outpad" physical_pb_type_name="io[physical].iopad" mode_bits="0"/> 
+    <!-- End physical pb_type binding in complex block IO -->
+
+    <!-- physical pb_type binding in complex block CLB -->
+    <!-- physical mode will be the default mode if not specified -->
+    <pb_type name="clb.fle" physical_mode_name="physical"/>
+    <pb_type name="clb.fle[physical].fabric.frac_logic.frac_lut4" circuit_model_name="frac_lut4" mode_bits="0"/>
+    <pb_type name="clb.fle[physical].fabric.frac_logic.carry_follower" circuit_model_name="sky130_fd_sc_hd__mux2_1_wrapper"/>
+    <pb_type name="clb.fle[physical].fabric.ff" circuit_model_name="sky130_fd_sc_hd__sdfrtp_1"/>
+    <!-- Binding operating pb_type to physical pb_type -->
+    <!-- Binding operating pb_types in mode 'ble4' -->
+    <pb_type name="clb.fle[n1_lut4].ble4.lut4" physical_pb_type_name="clb.fle[physical].fabric.frac_logic.frac_lut4" mode_bits="0">
+      <!-- Binding the lut4 to the first 4 inputs of fracturable lut4 -->
+      <port name="in" physical_mode_port="in[0:3]"/>
+      <port name="out" physical_mode_port="lut4_out"/>
+    </pb_type>
+    <pb_type name="clb.fle[n1_lut4].ble4.ff" physical_pb_type_name="clb.fle[physical].fabric.ff"/>
+    <!-- Binding operating pb_types in mode 'shift_register' -->
+    <pb_type name="clb.fle[shift_register].shift_reg.ff" physical_pb_type_name="clb.fle[physical].fabric.ff"/>
+    <!-- End physical pb_type binding in complex block IO -->
+  </pb_type_annotations>
+</openfpga_architecture>
diff --git a/ARCH/vpr_arch/k4_N8_tileable_reset_softadder_register_scan_chain_nonLR_caravel_io_skywater130nm.xml b/ARCH/vpr_arch/k4_N8_tileable_reset_softadder_register_scan_chain_nonLR_caravel_io_skywater130nm.xml
new file mode 100644
index 0000000..1d47257
--- /dev/null
+++ b/ARCH/vpr_arch/k4_N8_tileable_reset_softadder_register_scan_chain_nonLR_caravel_io_skywater130nm.xml
@@ -0,0 +1,591 @@
+<!-- 
+  Low-cost homogeneous FPGA Architecture.
+
+  - Skywater 130 nm technology
+  - General purpose logic block: 
+    K = 4, N = 8, fracturable 4 LUTs (can operate as one 4-LUT or two 3-LUTs with all 3 inputs shared) 
+    with optionally registered outputs
+  - Routing architecture:
+      - 10% L = 1, fc_in = 0.15, Fc_out = 0.10
+      - 10% L = 2, fc_in = 0.15, Fc_out = 0.10
+      - 80% L = 4, fc_in = 0.15, Fc_out = 0.10
+      - 100 routing tracks per channel
+
+  Authors: Xifan Tang
+-->
+<architecture>
+  <!-- 
+       ODIN II specific config begins 
+       Describes the types of user-specified netlist blocks (in blif, this corresponds to 
+       ".model [type_of_block]") that this architecture supports.
+
+       Note: Basic LUTs, I/Os, and flip-flops are not included here as there are 
+       already special structures in blif (.names, .input, .output, and .latch) 
+       that describe them.
+  -->
+  <models>
+    <!-- A virtual model for I/O to be used in the physical mode of io block -->
+    <model name="io">
+      <input_ports>
+        <port name="outpad"/>
+      </input_ports>
+      <output_ports>
+        <port name="inpad"/>
+      </output_ports>
+    </model>
+
+    <model name="frac_lut4">
+      <input_ports>
+        <port name="in"/>
+      </input_ports>
+      <output_ports>
+        <port name="lut2_out"/>
+        <port name="lut4_out"/>
+      </output_ports>
+    </model>
+    <model name="carry_follower">
+      <input_ports>
+        <port name="a"/>
+        <port name="b"/>
+        <port name="cin"/>
+      </input_ports>
+      <output_ports>
+        <port name="cout"/>
+      </output_ports>
+    </model>
+    <!-- A virtual model for scan-chain flip-flop to be used in the physical mode of FF -->
+    <model name="scff">
+      <input_ports>
+        <port name="D" clock="clk"/>
+        <port name="DI" clock="clk"/>
+        <port name="reset" clock="clk"/>
+        <port name="clk" is_clock="1"/>
+      </input_ports>
+      <output_ports>
+        <port name="Q" clock="clk"/>
+      </output_ports>
+    </model>
+  </models>
+  <tiles>
+    <!-- Do NOT add clock pins to I/O here!!! VPR does not build clock network in the way that OpenFPGA can support
+         If you need to register the I/O, define clocks in the circuit models
+         These clocks can be handled in back-end
+     -->
+    <!-- Top-side has 1 I/O per tile -->
+    <tile name="io_top" capacity="32" area="0">
+      <equivalent_sites>
+        <site pb_type="io"/>
+      </equivalent_sites>
+      <input name="outpad" num_pins="1"/>
+      <output name="inpad" num_pins="1"/>
+      <fc in_type="frac" in_val="0.15" out_type="frac" out_val="0.10"/>
+      <pinlocations pattern="custom">
+        <loc side="bottom">io_top.outpad io_top.inpad</loc>
+      </pinlocations>
+    </tile>
+    <!-- Right-side has 1 I/O per tile -->
+    <tile name="io_right" capacity="32" area="0">
+      <equivalent_sites>
+        <site pb_type="io"/>
+      </equivalent_sites>
+      <input name="outpad" num_pins="1"/>
+      <output name="inpad" num_pins="1"/>
+      <fc in_type="frac" in_val="0.15" out_type="frac" out_val="0.10"/>
+      <pinlocations pattern="custom">
+        <loc side="left">io_right.outpad io_right.inpad</loc>
+      </pinlocations>
+    </tile>
+    <!-- Bottom-side has 9 I/O per tile -->
+    <tile name="io_bottom" capacity="32" area="0">
+      <equivalent_sites>
+        <site pb_type="io"/>
+      </equivalent_sites>
+      <input name="outpad" num_pins="1"/>
+      <output name="inpad" num_pins="1"/>
+      <fc in_type="frac" in_val="0.15" out_type="frac" out_val="0.10"/>
+      <pinlocations pattern="custom">
+        <loc side="top">io_bottom.outpad io_bottom.inpad</loc>
+      </pinlocations>
+    </tile>
+    <!-- Left-side has 1 I/O per tile -->
+    <tile name="io_left" capacity="32" area="0">
+      <equivalent_sites>
+        <site pb_type="io"/>
+      </equivalent_sites>
+      <input name="outpad" num_pins="1"/>
+      <output name="inpad" num_pins="1"/>
+      <fc in_type="frac" in_val="0.15" out_type="frac" out_val="0.10"/>
+      <pinlocations pattern="custom">
+        <loc side="right">io_left.outpad io_left.inpad</loc>
+      </pinlocations>
+    </tile>
+    <!-- CLB has most pins on the top and right sides -->
+    <tile name="clb" area="53894">
+      <equivalent_sites>
+        <site pb_type="clb"/>
+      </equivalent_sites>
+      <input name="I" num_pins="24" equivalent="full"/>
+      <input name="reg_in" num_pins="1"/>
+      <input name="sc_in" num_pins="1"/>
+      <input name="cin" num_pins="1"/>
+      <input name="reset" num_pins="1" is_non_clock_global="true"/>
+      <output name="O" num_pins="8" equivalent="none"/>
+      <output name="reg_out" num_pins="1"/>
+      <output name="sc_out" num_pins="1"/>
+      <output name="cout" num_pins="1"/>
+      <clock name="clk" num_pins="1"/>
+      <fc in_type="frac" in_val="0.15" out_type="frac" out_val="0.10">
+        <fc_override port_name="reg_in" fc_type="frac" fc_val="0"/>
+        <fc_override port_name="reg_out" fc_type="frac" fc_val="0"/>
+        <fc_override port_name="sc_in" fc_type="frac" fc_val="0"/>
+        <fc_override port_name="sc_out" fc_type="frac" fc_val="0"/>
+        <fc_override port_name="cin" fc_type="frac" fc_val="0"/>
+        <fc_override port_name="cout" fc_type="frac" fc_val="0"/>
+        <fc_override port_name="clk" fc_type="frac" fc_val="0"/>
+        <fc_override port_name="reset" fc_type="frac" fc_val="0"/>
+      </fc>
+      <!--pinlocations pattern="spread"/-->
+      <pinlocations pattern="custom">
+        <loc side="left">clb.clk clb.reset</loc>
+        <loc side="top">clb.reg_in clb.sc_in clb.cin clb.O[7:0] clb.I[11:0]</loc>
+        <loc side="right">clb.I[23:12]</loc>
+        <loc side="bottom">clb.reg_out clb.sc_out clb.cout</loc>
+      </pinlocations>
+    </tile>
+  </tiles>
+  <!-- ODIN II specific config ends -->
+  <!-- Physical descriptions begin -->
+  <layout tileable="true">
+    <auto_layout aspect_ratio="1.0">
+      <!--Perimeter of 'io' blocks with 'EMPTY' blocks at corners-->
+      <row type="io_top" starty="H-1" priority="100"/>
+      <row type="io_bottom" starty="0" priority="100"/>
+      <col type="io_left" startx="0" priority="100"/>
+      <col type="io_right" startx="W-1" priority="100"/>
+      <corners type="EMPTY" priority="101"/>
+      <!--Fill with 'clb'-->
+      <fill type="clb" priority="10"/>
+    </auto_layout>
+    <fixed_layout name="2x2" width="4" height="4">
+      <!--Perimeter of 'io' blocks with 'EMPTY' blocks at corners-->
+      <row type="io_top" starty="H-1" priority="100"/>
+      <row type="io_bottom" starty="0" priority="100"/>
+      <col type="io_left" startx="0" priority="100"/>
+      <col type="io_right" startx="W-1" priority="100"/>
+      <corners type="EMPTY" priority="101"/>
+      <!--Fill with 'clb'-->
+      <fill type="clb" priority="10"/>
+    </fixed_layout>
+    <fixed_layout name="12x12" width="14" height="14">
+      <!--Perimeter of 'io' blocks with 'EMPTY' blocks at corners-->
+      <row type="io_top" starty="H-1" priority="100"/>
+      <row type="io_bottom" starty="0" priority="100"/>
+      <col type="io_left" startx="0" priority="100"/>
+      <col type="io_right" startx="W-1" priority="100"/>
+      <corners type="EMPTY" priority="101"/>
+      <!--Fill with 'clb'-->
+      <fill type="clb" priority="10"/>
+    </fixed_layout>
+    <fixed_layout name="32x32" width="34" height="34">
+      <!--Perimeter of 'io' blocks with 'EMPTY' blocks at corners-->
+      <row type="io_top" starty="H-1" priority="100"/>
+      <row type="io_bottom" starty="0" priority="100"/>
+      <col type="io_left" startx="0" priority="100"/>
+      <col type="io_right" startx="W-1" priority="100"/>
+      <corners type="EMPTY" priority="101"/>
+      <!--Fill with 'clb'-->
+      <fill type="clb" priority="10"/>
+    </fixed_layout>
+  </layout>
+  <device>
+    <!-- VB & JL: Using Ian Kuon's transistor sizing and drive strength data for routing, at 40 nm. Ian used BPTM 
+			     models. We are modifying the delay values however, to include metal C and R, which allows more architecture
+			     experimentation. We are also modifying the relative resistance of PMOS to be 1.8x that of NMOS
+			     (vs. Ian's 3x) as 1.8x lines up with Jeff G's data from a 45 nm process (and is more typical of 
+			     45 nm in general). I'm upping the Rmin_nmos from Ian's just over 6k to nearly 9k, and dropping 
+			     RminW_pmos from 18k to 16k to hit this 1.8x ratio, while keeping the delays of buffers approximately
+			     lined up with Stratix IV. 
+			     We are using Jeff G.'s capacitance data for 45 nm (in tech/ptm_45nm).
+			     Jeff's tables list C in for transistors with widths in multiples of the minimum feature size (45 nm).
+			     The minimum contactable transistor is 2.5 * 45 nm, so I need to multiply drive strength sizes in this file
+	                     by 2.5x when looking up in Jeff's tables.
+			     The delay values are lined up with Stratix IV, which has an architecture similar to this
+			     proposed FPGA, and which is also 40 nm 
+			     C_ipin_cblock: input capacitance of a track buffer, which VPR assumes is a single-stage
+			     4x minimum drive strength buffer. -->
+    <sizing R_minW_nmos="8926" R_minW_pmos="16067"/>
+    <!-- The grid_logic_tile_area below will be used for all blocks that do not explicitly set their own (non-routing)
+     	  area; set to 0 since we explicitly set the area of all blocks currently in this architecture file.
+	  -->
+    <area grid_logic_tile_area="0"/>
+    <chan_width_distr>
+      <x distr="uniform" peak="1.000000"/>
+      <y distr="uniform" peak="1.000000"/>
+    </chan_width_distr>
+    <switch_block type="wilton" fs="3" sub_type="subset" sub_fs="3"/>
+    <connection_block input_switch_name="ipin_cblock"/>
+  </device>
+  <switchlist>
+    <!-- VB: the mux_trans_size and buf_size data below is in minimum width transistor *areas*, assuming the purple
+	       book area formula. This means the mux transistors are about 5x minimum drive strength.
+	       We assume the first stage of the buffer is 3x min drive strength to be reasonable given the large 
+	       mux transistors, and this gives a reasonable stage ratio of a bit over 5x to the second stage. We assume
+	       the n and p transistors in the first stage are equal-sized to lower the buffer trip point, since it's fed
+	       by a pass transistor mux. We can then reverse engineer the buffer second stage to hit the specified 
+	       buf_size (really buffer area) - 16.2x minimum drive nmos and 1.8*16.2 = 29.2x minimum drive.
+	       I then took the data from Jeff G.'s PTM modeling of 45 nm to get the Cin (gate of first stage) and Cout 
+	       (diff of second stage) listed below.  Jeff's models are in tech/ptm_45nm, and are in min feature multiples.
+	       The minimum contactable transistor is 2.5 * 45 nm, so I need to multiply the drive strength sizes above by 
+	       2.5x when looking up in Jeff's tables.
+	       Finally, we choose a switch delay (58 ps) that leads to length 4 wires having a delay equal to that of SIV of 126 ps.
+	       This also leads to the switch being 46% of the total wire delay, which is reasonable. -->
+    <switch type="mux" name="L1_mux" R="551" Cin=".77e-15" Cout="4e-15" Tdel="58e-12" mux_trans_size="2.630740" buf_size="27.645901"/>
+    <switch type="mux" name="L2_mux" R="551" Cin=".77e-15" Cout="4e-15" Tdel="58e-12" mux_trans_size="2.630740" buf_size="27.645901"/>
+    <switch type="mux" name="L4_mux" R="551" Cin=".77e-15" Cout="4e-15" Tdel="58e-12" mux_trans_size="2.630740" buf_size="27.645901"/>
+    <!--switch ipin_cblock resistance set to yeild for 4x minimum drive strength buffer-->
+    <switch type="mux" name="ipin_cblock" R="2231.5" Cout="0." Cin="1.47e-15" Tdel="7.247000e-11" mux_trans_size="1.222260" buf_size="auto"/>
+  </switchlist>
+  <segmentlist>
+    <!--- VB & JL: using ITRS metal stack data, 96 nm half pitch wires, which are intermediate metal width/space.  
+			     With the 96 nm half pitch, such wires would take 60 um of height, vs. a 90 nm high (approximated as square) Stratix IV tile so this seems
+			     reasonable. Using a tile length of 90 nm, corresponding to the length of a Stratix IV tile if it were square. -->
+    <!-- GIVE a specific name for the segment! OpenFPGA appreciate that! -->
+    <segment name="L1" freq="0.10" length="1" type="unidir" Rmetal="101" Cmetal="22.5e-15">
+      <mux name="L1_mux"/>
+      <sb type="pattern">1 1</sb>
+      <cb type="pattern">1</cb>
+    </segment>
+    <segment name="L2" freq="0.10" length="2" type="unidir" Rmetal="101" Cmetal="22.5e-15">
+      <mux name="L2_mux"/>
+      <sb type="pattern">1 1 1</sb>
+      <cb type="pattern">1 1</cb>
+    </segment>
+    <segment name="L4" freq="0.80" length="4" type="unidir" Rmetal="101" Cmetal="22.5e-15">
+      <mux name="L4_mux"/>
+      <sb type="pattern">1 1 1 1 1</sb>
+      <cb type="pattern">1 1 1 1</cb>
+    </segment>
+  </segmentlist>
+  <directlist>
+    <direct name="carry_chain" from_pin="clb.cout" to_pin="clb.cin" x_offset="0" y_offset="-1" z_offset="0"/>
+    <direct name="shift_register" from_pin="clb.reg_out" to_pin="clb.reg_in" x_offset="0" y_offset="-1" z_offset="0"/>
+    <direct name="scan_chain" from_pin="clb.sc_out" to_pin="clb.sc_in" x_offset="0" y_offset="-1" z_offset="0"/>
+  </directlist>
+  <complexblocklist>
+    <!-- Define input pads begin -->
+    <pb_type name="io">
+      <input name="outpad" num_pins="1"/>
+      <output name="inpad" num_pins="1"/>
+      <!-- Do NOT add clock pins to I/O here!!! VPR does not build clock network in the way that OpenFPGA can support
+           If you need to register the I/O, define clocks in the circuit models
+           These clocks can be handled in back-end
+       -->
+      <!-- A mode denotes the physical implementation of an I/O 
+           This mode will be not packable but is mainly used for fabric verilog generation   
+        -->
+      <mode name="physical" disabled_in_pack="true">
+        <pb_type name="iopad" blif_model=".subckt io" num_pb="1">
+          <input name="outpad" num_pins="1"/>
+          <output name="inpad" num_pins="1"/>
+        </pb_type>
+        <interconnect>
+          <direct name="outpad" input="io.outpad" output="iopad.outpad">
+            <delay_constant max="1.394e-11" in_port="io.outpad" out_port="iopad.outpad"/>
+          </direct>
+          <direct name="inpad" input="iopad.inpad" output="io.inpad">
+            <delay_constant max="4.243e-11" in_port="iopad.inpad" out_port="io.inpad"/>
+          </direct>
+        </interconnect>
+      </mode>
+
+      <!-- IOs can operate as either inputs or outputs.
+	     Delays below come from Ian Kuon. They are small, so they should be interpreted as
+	     the delays to and from registers in the I/O (and generally I/Os are registered 
+	     today and that is when you timing analyze them.
+	     -->
+      <mode name="inpad">
+        <pb_type name="inpad" blif_model=".input" num_pb="1">
+          <output name="inpad" num_pins="1"/>
+        </pb_type>
+        <interconnect>
+          <direct name="inpad" input="inpad.inpad" output="io.inpad">
+            <delay_constant max="4.243e-11" in_port="inpad.inpad" out_port="io.inpad"/>
+          </direct>
+        </interconnect>
+      </mode>
+      <mode name="outpad">
+        <pb_type name="outpad" blif_model=".output" num_pb="1">
+          <input name="outpad" num_pins="1"/>
+        </pb_type>
+        <interconnect>
+          <direct name="outpad" input="io.outpad" output="outpad.outpad">
+            <delay_constant max="1.394e-11" in_port="io.outpad" out_port="outpad.outpad"/>
+          </direct>
+        </interconnect>
+      </mode>
+      <power method="ignore"/>
+    </pb_type>
+    <!-- Define I/O pads ends -->
+    <!-- Define general purpose logic block (CLB) begin -->
+    <!-- -Due to the absence of local routing, 
+         the 4 inputs of fracturable LUT4 are no longer equivalent, 
+         because the 4th input can not be switched when the dual-LUT3 modes are used.
+         So pin equivalence should be applied to the first 3 inputs only
+	  -->
+    <pb_type name="clb">
+      <input name="I" num_pins="24" equivalent="full"/>
+      <input name="reg_in" num_pins="1"/>
+      <input name="sc_in" num_pins="1"/>
+      <input name="cin" num_pins="1"/>
+      <input name="reset" num_pins="1" is_non_clock_global="true"/>
+      <output name="O" num_pins="8" equivalent="none"/>
+      <output name="reg_out" num_pins="1"/>
+      <output name="sc_out" num_pins="1"/>
+      <output name="cout" num_pins="1"/>
+      <clock name="clk" num_pins="1"/>
+      <!-- Describe fracturable logic element.  
+             Each fracturable logic element has a 6-LUT that can alternatively operate as two 5-LUTs with shared inputs. 
+             The outputs of the fracturable logic element can be optionally registered
+        -->
+      <pb_type name="fle" num_pb="8">
+        <input name="in" num_pins="4"/>
+        <input name="reg_in" num_pins="1"/>
+        <input name="sc_in" num_pins="1"/>
+        <input name="cin" num_pins="1"/>
+        <input name="reset" num_pins="1"/>
+        <output name="out" num_pins="1"/>
+        <output name="reg_out" num_pins="1"/>
+        <output name="sc_out" num_pins="1"/>
+        <output name="cout" num_pins="1"/>
+        <clock name="clk" num_pins="1"/>
+        <!-- Physical mode definition begin (physical implementation of the fle) -->
+        <mode name="physical" disabled_in_pack="true">
+          <pb_type name="fabric" num_pb="1">
+            <input name="in" num_pins="4"/>
+            <input name="reg_in" num_pins="1"/>
+            <input name="sc_in" num_pins="1"/>
+            <input name="cin" num_pins="1"/>
+            <input name="reset" num_pins="1"/>
+            <output name="out" num_pins="1"/>
+            <output name="reg_out" num_pins="1"/>
+            <output name="sc_out" num_pins="1"/>
+            <output name="cout" num_pins="1"/>
+            <clock name="clk" num_pins="1"/>
+            <pb_type name="frac_logic" num_pb="1">
+              <input name="in" num_pins="4"/>
+              <input name="cin" num_pins="1"/>
+              <output name="out" num_pins="1"/>
+              <output name="cout" num_pins="1"/>
+              <!-- Define LUT -->
+              <pb_type name="frac_lut4" blif_model=".subckt frac_lut4" num_pb="1">
+                <input name="in" num_pins="4"/>
+                <output name="lut2_out" num_pins="2"/>
+                <output name="lut4_out" num_pins="1"/>
+              </pb_type>
+              <pb_type name="carry_follower" blif_model=".subckt carry_follower" num_pb="1">
+                <input name="a" num_pins="1"/>
+                <input name="b" num_pins="1"/>
+                <input name="cin" num_pins="1"/>
+                <output name="cout" num_pins="1"/>
+              </pb_type>
+              <interconnect>
+                <direct name="direct1" input="frac_logic.in[0:1]" output="frac_lut4.in[0:1]"/>
+                <direct name="direct2" input="frac_logic.in[3:3]" output="frac_lut4.in[3:3]"/>
+                <direct name="direct3" input="frac_logic.cin" output="carry_follower.b"/>
+                <direct name="direct4" input="frac_lut4.lut2_out[1:1]" output="carry_follower.a"/>
+                <direct name="direct5" input="frac_lut4.lut2_out[0:0]" output="carry_follower.cin"/>
+                <direct name="direct6" input="carry_follower.cout" output="frac_logic.cout"/>
+                <!-- Xifan Tang: I use out[0] because the output of lut6 in lut6 mode is wired to the out[0] -->
+                <direct name="direct7" input="frac_lut4.lut4_out" output="frac_logic.out"/>
+                <mux name="mux2" input="frac_logic.cin frac_logic.in[2:2]" output="frac_lut4.in[2:2]"/>
+              </interconnect>
+            </pb_type>
+            <!-- Define flip-flop with scan-chain capability, DI is the scan-chain data input -->
+            <pb_type name="ff" blif_model=".subckt scff" num_pb="1">
+              <input name="D" num_pins="1"/>
+              <input name="DI" num_pins="1"/>
+              <input name="reset" num_pins="1"/>
+              <output name="Q" num_pins="1"/>
+              <clock name="clk" num_pins="1"/>
+              <T_setup value="66e-12" port="ff.D" clock="clk"/>
+              <T_setup value="66e-12" port="ff.DI" clock="clk"/>
+              <T_setup value="66e-12" port="ff.reset" clock="clk"/>
+              <T_clock_to_Q max="124e-12" port="ff.Q" clock="clk"/>
+            </pb_type>         
+            <interconnect>
+              <direct name="direct1" input="fabric.in" output="frac_logic.in"/>
+              <direct name="direct2" input="fabric.sc_in" output="ff.DI"/>
+              <direct name="direct4" input="ff.Q" output="fabric.sc_out"/>
+              <direct name="direct5" input="ff.Q" output="fabric.reg_out"/>
+              <complete name="complete1" input="fabric.clk" output="ff.clk"/>
+              <complete name="complete2" input="fabric.reset" output="ff.reset"/>
+              <mux name="mux1" input="frac_logic.out fabric.reg_in" output="ff.D">
+                <delay_constant max="25e-12" in_port="frac_logic.out" out_port="ff.D"/>
+                <delay_constant max="45e-12" in_port="fabric.reg_in" out_port="ff.D"/>
+              </mux>
+              <mux name="mux2" input="ff.Q frac_logic.out" output="fabric.out">
+                <!-- LUT to output is faster than FF to output on a Stratix IV -->
+                <delay_constant max="25e-12" in_port="frac_logic.out" out_port="fabric.out"/>
+                <delay_constant max="45e-12" in_port="ff.Q" out_port="fabric.out"/>
+              </mux>
+            </interconnect>
+          </pb_type>
+          <interconnect>
+            <direct name="direct1" input="fle.in" output="fabric.in"/>
+            <direct name="direct2" input="fle.reg_in" output="fabric.reg_in"/>
+            <direct name="direct3" input="fle.sc_in" output="fabric.sc_in"/>
+            <direct name="direct4" input="fle.cin" output="fabric.cin"/>
+            <direct name="direct5" input="fabric.out" output="fle.out"/>
+            <direct name="direct6" input="fabric.reg_out" output="fle.reg_out"/>
+            <direct name="direct7" input="fabric.sc_out" output="fle.sc_out"/>
+            <direct name="direct8" input="fabric.cout" output="fle.cout"/>
+            <direct name="direct9" input="fle.clk" output="fabric.clk"/>
+            <direct name="direct10" input="fle.reset" output="fabric.reset"/>
+          </interconnect>
+        </mode>
+        <!-- Physical mode definition end (physical implementation of the fle) -->
+        <mode name="n1_lut4">
+          <!-- Define 4-LUT mode -->
+          <pb_type name="ble4" num_pb="1">
+            <input name="in" num_pins="4"/>
+            <output name="out" num_pins="1"/>
+            <clock name="clk" num_pins="1"/>
+            <!-- Define LUT -->
+            <pb_type name="lut4" blif_model=".names" num_pb="1" class="lut">
+              <input name="in" num_pins="4" port_class="lut_in"/>
+              <output name="out" num_pins="1" port_class="lut_out"/>
+              <!-- LUT timing using delay matrix -->
+              <!-- These are the physical delay inputs on a Stratix IV LUT but because VPR cannot do LUT rebalancing,
+                       we instead take the average of these numbers to get more stable results
+                  82e-12
+                  173e-12
+                  261e-12
+                  263e-12
+                  398e-12
+                  397e-12
+                  -->
+              <delay_matrix type="max" in_port="lut4.in" out_port="lut4.out">
+                261e-12
+                261e-12
+                261e-12
+                261e-12
+              </delay_matrix>
+            </pb_type>
+            <!-- Define flip-flop -->
+            <pb_type name="ff" blif_model=".latch" num_pb="1" class="flipflop">
+              <input name="D" num_pins="1" port_class="D"/>
+              <output name="Q" num_pins="1" port_class="Q"/>
+              <clock name="clk" num_pins="1" port_class="clock"/>
+              <T_setup value="66e-12" port="ff.D" clock="clk"/>
+              <T_clock_to_Q max="124e-12" port="ff.Q" clock="clk"/>
+            </pb_type>
+            <interconnect>
+              <direct name="direct1" input="ble4.in" output="lut4[0:0].in"/>
+              <direct name="direct2" input="lut4.out" output="ff.D">
+                <!-- Advanced user option that tells CAD tool to find LUT+FF pairs in netlist -->
+                <pack_pattern name="ble4" in_port="lut4.out" out_port="ff.D"/>
+              </direct>
+              <direct name="direct3" input="ble4.clk" output="ff.clk"/>
+              <mux name="mux1" input="ff.Q lut4.out" output="ble4.out">
+                <!-- LUT to output is faster than FF to output on a Stratix IV -->
+                <delay_constant max="25e-12" in_port="lut4.out" out_port="ble4.out"/>
+                <delay_constant max="45e-12" in_port="ff.Q" out_port="ble4.out"/>
+              </mux>
+            </interconnect>
+          </pb_type>
+          <interconnect>
+            <direct name="direct1" input="fle.in" output="ble4.in"/>
+            <direct name="direct2" input="ble4.out" output="fle.out"/>
+            <direct name="direct3" input="fle.clk" output="ble4.clk"/>
+          </interconnect>
+        </mode>
+        <!-- 4-LUT mode definition end -->
+        <!-- Define shift register begin -->
+        <mode name="shift_register">
+          <pb_type name="shift_reg" num_pb="1">
+            <input name="reg_in" num_pins="1"/>
+            <output name="ff_out" num_pins="1"/>
+            <output name="reg_out" num_pins="1"/>
+            <clock name="clk" num_pins="1"/>
+            <pb_type name="ff" blif_model=".latch" num_pb="1" class="flipflop">
+              <input name="D" num_pins="1" port_class="D"/>
+              <output name="Q" num_pins="1" port_class="Q"/>
+              <clock name="clk" num_pins="1" port_class="clock"/>
+              <T_setup value="66e-12" port="ff.D" clock="clk"/>
+              <T_clock_to_Q max="124e-12" port="ff.Q" clock="clk"/>
+            </pb_type>
+            <interconnect>
+              <direct name="direct1" input="shift_reg.reg_in" output="ff.D"/>
+              <direct name="direct3" input="ff.Q" output="shift_reg.reg_out"/>
+              <direct name="direct4" input="ff.Q" output="shift_reg.ff_out"/>
+              <complete name="complete1" input="shift_reg.clk" output="ff.clk"/>
+            </interconnect>
+          </pb_type>
+          <interconnect>
+            <direct name="direct1" input="fle.reg_in" output="shift_reg.reg_in"/>
+            <direct name="direct2" input="shift_reg.reg_out" output="fle.reg_out"/>
+            <direct name="direct3" input="shift_reg.ff_out" output="fle.out"/>
+            <direct name="direct4" input="fle.clk" output="shift_reg.clk"/>
+          </interconnect>
+        </mode>
+        <!-- Define shift register end --> 
+      </pb_type>
+      <interconnect>
+        <!-- We use direct connections to reduce the area to the most
+             The global local routing is going to compensate the loss in routability
+          -->
+        <!-- FIXME: The implicit port definition results in I0[0] connected to
+                    in[2]. Such twisted connection is not expected.
+                    I[0] should be connected to in[0]
+	  -->
+	<complete name="crossbar" input="clb.I fle[7:0].out" output="fle[7:0].in">
+          <!-- TODO: Timing should be backannotated from post-PnR results -->
+        </complete>
+        <complete name="clks" input="clb.clk" output="fle[7:0].clk">
+        </complete>
+        <complete name="resets" input="clb.reset" output="fle[7:0].reset">
+        </complete>
+        <!-- This way of specifying direct connection to clb outputs is important because this architecture uses automatic spreading of opins.  
+               By grouping to output pins in this fashion, if a logic block is completely filled by 6-LUTs, 
+               then the outputs those 6-LUTs take get evenly distributed across all four sides of the CLB instead of clumped on two sides (which is what happens with a more
+               naive specification).
+          -->
+        <direct name="clbouts1" input="fle[3:0].out" output="clb.O[3:0]"/>
+        <direct name="clbouts2" input="fle[7:4].out" output="clb.O[7:4]"/>
+        <!-- Shift register chain links -->
+        <direct name="shift_register_in" input="clb.reg_in" output="fle[0:0].reg_in">
+          <!-- Put all inter-block carry chain delay on this one edge -->
+          <delay_constant max="0.16e-9" in_port="clb.reg_in" out_port="fle[0:0].reg_in"/>
+          <!--pack_pattern name="chain" in_port="clb.reg_in" out_port="fle[0:0].reg_in"/-->
+        </direct>
+        <direct name="shift_register_out" input="fle[7:7].reg_out" output="clb.reg_out">
+          <!--pack_pattern name="chain" in_port="fle[7:7].reg_out" out_port="clb.reg_out"/-->
+        </direct>
+        <direct name="shift_register_link" input="fle[6:0].reg_out" output="fle[7:1].reg_in">
+          <!--pack_pattern name="chain" in_port="fle[6:0].reg_out" out_port="fle[7:1].reg_in"/-->
+        </direct>
+        <!-- Scan chain links -->
+        <direct name="scan_chain_in" input="clb.sc_in" output="fle[0:0].sc_in">
+          <!-- Put all inter-block carry chain delay on this one edge -->
+          <delay_constant max="0.16e-9" in_port="clb.sc_in" out_port="fle[0:0].sc_in"/>
+        </direct>
+        <direct name="scan_chain_out" input="fle[7:7].sc_out" output="clb.sc_out">
+        </direct>
+        <direct name="scan_chain_link" input="fle[6:0].sc_out" output="fle[7:1].sc_in">
+        </direct>
+        <!-- Carry chain links -->
+        <direct name="carry_chain_in" input="clb.cin" output="fle[0:0].cin">
+          <!-- Put all inter-block carry chain delay on this one edge -->
+          <delay_constant max="0.16e-9" in_port="clb.cin" out_port="fle[0:0].cin"/>
+        </direct>
+        <direct name="carry_chain_out" input="fle[7:7].cout" output="clb.cout">
+        </direct>
+        <direct name="carry_chain_link" input="fle[6:0].cout" output="fle[7:1].cin">
+        </direct>
+      </interconnect>
+      <!-- Every input pin is driven by 15% of the tracks in a channel, every output pin is driven by 10% of the tracks in a channel -->
+      <!-- Place this general purpose logic block in any unspecified column -->
+    </pb_type>
+    <!-- Define general purpose logic block (CLB) ends -->
+  </complexblocklist>
+</architecture>
diff --git a/SCRIPT/skywater_openfpga_task/k4_N8_reset_softadder_caravel_cc_fdhd_32x32/generate_fabric/config/task_template.conf b/SCRIPT/skywater_openfpga_task/k4_N8_reset_softadder_caravel_cc_fdhd_32x32/generate_fabric/config/task_template.conf
index 9b8fd8b..b9f99be 100644
--- a/SCRIPT/skywater_openfpga_task/k4_N8_reset_softadder_caravel_cc_fdhd_32x32/generate_fabric/config/task_template.conf
+++ b/SCRIPT/skywater_openfpga_task/k4_N8_reset_softadder_caravel_cc_fdhd_32x32/generate_fabric/config/task_template.conf
@@ -17,7 +17,7 @@ fpga_flow=yosys_vpr
 
 [OpenFPGA_SHELL]
 openfpga_shell_template=${SKYWATER_OPENFPGA_HOME}/SCRIPT/openfpga_shell_script/skywater_generate_fabric_using_random_key_example_script.openfpga
-openfpga_arch_file=${SKYWATER_OPENFPGA_HOME}/ARCH/openfpga_arch/k4_frac_N8_reset_softadder_register_scan_chain_caravel_io_skywater130nm_fdhd_cc_openfpga.xml
+openfpga_arch_file=${SKYWATER_OPENFPGA_HOME}/ARCH/openfpga_arch/k4_N8_reset_softadder_register_scan_chain_caravel_io_skywater130nm_fdhd_cc_openfpga.xml
 openfpga_sim_setting_file=${SKYWATER_OPENFPGA_HOME}/SCRIPT/openfpga_simulation_setting/efpga_12x12_sim_openfpga.xml
 openfpga_vpr_device_layout=32x32
 openfpga_vpr_route_chan_width=60
@@ -26,7 +26,7 @@ openfpga_sdc_output_dir=${SKYWATER_OPENFPGA_HOME}/SDC/k4_N8_reset_softadder_cara
 external_fabric_key_file=${SKYWATER_OPENFPGA_HOME}/ARCH/fabric_key/fabric_key_12x12.xml
 
 [ARCHITECTURES]
-arch0=${SKYWATER_OPENFPGA_HOME}/ARCH/vpr_arch/k4_frac_N8_tileable_reset_softadder_register_scan_chain_nonLR_caravel_io_skywater130nm.xml
+arch0=${SKYWATER_OPENFPGA_HOME}/ARCH/vpr_arch/k4_N8_tileable_reset_softadder_register_scan_chain_nonLR_caravel_io_skywater130nm.xml
 
 [BENCHMARKS]
 bench0=${SKYWATER_OPENFPGA_HOME}/BENCHMARK/and2/and2.v
diff --git a/SCRIPT/skywater_openfpga_task/k4_N8_reset_softadder_caravel_cc_fdhd_32x32/generate_sdc/config/task_template.conf b/SCRIPT/skywater_openfpga_task/k4_N8_reset_softadder_caravel_cc_fdhd_32x32/generate_sdc/config/task_template.conf
index d94dadf..c2902b0 100644
--- a/SCRIPT/skywater_openfpga_task/k4_N8_reset_softadder_caravel_cc_fdhd_32x32/generate_sdc/config/task_template.conf
+++ b/SCRIPT/skywater_openfpga_task/k4_N8_reset_softadder_caravel_cc_fdhd_32x32/generate_sdc/config/task_template.conf
@@ -17,7 +17,7 @@ fpga_flow=yosys_vpr
 
 [OpenFPGA_SHELL]
 openfpga_shell_template=${SKYWATER_OPENFPGA_HOME}/SCRIPT/openfpga_shell_script/skywater_generate_sdc_using_random_key_example_script.openfpga
-openfpga_arch_file=${SKYWATER_OPENFPGA_HOME}/ARCH/openfpga_arch/k4_frac_N8_reset_softadder_register_scan_chain_caravel_io_skywater130nm_fdhd_cc_openfpga.xml
+openfpga_arch_file=${SKYWATER_OPENFPGA_HOME}/ARCH/openfpga_arch/k4_N8_reset_softadder_register_scan_chain_caravel_io_skywater130nm_fdhd_cc_openfpga.xml
 openfpga_sim_setting_file=${SKYWATER_OPENFPGA_HOME}/SCRIPT/openfpga_simulation_setting/efpga_12x12_sim_openfpga.xml
 openfpga_vpr_device_layout=32x32
 openfpga_vpr_route_chan_width=60
@@ -25,7 +25,7 @@ openfpga_sdc_output_dir=${SKYWATER_OPENFPGA_HOME}/SDC/k4_N8_reset_softadder_cara
 external_fabric_key_file=${SKYWATER_OPENFPGA_HOME}/ARCH/fabric_key/fabric_key_12x12.xml
 
 [ARCHITECTURES]
-arch0=${SKYWATER_OPENFPGA_HOME}/ARCH/vpr_arch/k4_frac_N8_tileable_reset_softadder_register_scan_chain_nonLR_caravel_io_skywater130nm.xml
+arch0=${SKYWATER_OPENFPGA_HOME}/ARCH/vpr_arch/k4_N8_tileable_reset_softadder_register_scan_chain_nonLR_caravel_io_skywater130nm.xml
 
 [BENCHMARKS]
 bench0=${SKYWATER_OPENFPGA_HOME}/BENCHMARK/and2/and2.v
diff --git a/SCRIPT/skywater_openfpga_task/k4_N8_reset_softadder_caravel_cc_fdhd_32x32/generate_testbench/config/task_template.conf b/SCRIPT/skywater_openfpga_task/k4_N8_reset_softadder_caravel_cc_fdhd_32x32/generate_testbench/config/task_template.conf
index 52da311..6bf2eea 100644
--- a/SCRIPT/skywater_openfpga_task/k4_N8_reset_softadder_caravel_cc_fdhd_32x32/generate_testbench/config/task_template.conf
+++ b/SCRIPT/skywater_openfpga_task/k4_N8_reset_softadder_caravel_cc_fdhd_32x32/generate_testbench/config/task_template.conf
@@ -17,7 +17,7 @@ fpga_flow=yosys_vpr
 
 [OpenFPGA_SHELL]
 openfpga_shell_template=${SKYWATER_OPENFPGA_HOME}/SCRIPT/openfpga_shell_script/skywater_generate_testbench_using_random_key_example_script.openfpga
-openfpga_arch_file=${SKYWATER_OPENFPGA_HOME}/ARCH/openfpga_arch/k4_frac_N8_reset_softadder_register_scan_chain_caravel_io_skywater130nm_fdhd_cc_openfpga.xml
+openfpga_arch_file=${SKYWATER_OPENFPGA_HOME}/ARCH/openfpga_arch/k4_N8_reset_softadder_register_scan_chain_caravel_io_skywater130nm_fdhd_cc_openfpga.xml
 openfpga_sim_setting_file=${SKYWATER_OPENFPGA_HOME}/SCRIPT/openfpga_simulation_setting/efpga_12x12_sim_openfpga.xml
 openfpga_vpr_device_layout=32x32
 openfpga_vpr_route_chan_width=60
@@ -26,7 +26,7 @@ openfpga_fabric_verilog_netlist=${SKYWATER_OPENFPGA_HOME}/HDL/k4_N8_reset_softad
 external_fabric_key_file=${SKYWATER_OPENFPGA_HOME}/ARCH/fabric_key/fabric_key_12x12.xml
 
 [ARCHITECTURES]
-arch0=${SKYWATER_OPENFPGA_HOME}/ARCH/vpr_arch/k4_frac_N8_tileable_reset_softadder_register_scan_chain_nonLR_caravel_io_skywater130nm.xml
+arch0=${SKYWATER_OPENFPGA_HOME}/ARCH/vpr_arch/k4_N8_tileable_reset_softadder_register_scan_chain_nonLR_caravel_io_skywater130nm.xml
 
 [BENCHMARKS]
 bench0=${SKYWATER_OPENFPGA_HOME}/BENCHMARK/and2/and2.v
@@ -43,7 +43,7 @@ bench9=${SKYWATER_OPENFPGA_HOME}/BENCHMARK/cf_fft_256_8/rtl/*.v
 bench10=${SKYWATER_OPENFPGA_HOME}/BENCHMARK/counter120bitx5/rtl/*.v
 bench11=${SKYWATER_OPENFPGA_HOME}/BENCHMARK/counter_16bit/rtl/*.v
 bench12=${SKYWATER_OPENFPGA_HOME}/BENCHMARK/dct_mac/rtl/*.v
-bench13=${SKYWATER_OPENFPGA_HOME}/BENCHMARK/des_perf/rtl/*.v
+#bench13=${SKYWATER_OPENFPGA_HOME}/BENCHMARK/des_perf/rtl/*.v
 bench14=${SKYWATER_OPENFPGA_HOME}/BENCHMARK/diffeq_f_systemC/rtl/*.v
 #bench15=${SKYWATER_OPENFPGA_HOME}/BENCHMARK/i2c_master_top/rtl/*.v
 bench16=${SKYWATER_OPENFPGA_HOME}/BENCHMARK/iir/rtl/*.v
@@ -68,7 +68,7 @@ bench9_top = cf_fft_256_8
 bench10_top = counter120bitx5
 bench11_top = top
 bench12_top = dct_mac 
-bench13_top = des_perf
+#bench13_top = des_perf
 bench14_top = diffeq_f_systemC 
 #bench15_top = i2c_master_top 
 bench16_top = iir