795 lines
15 KiB
Verilog
795 lines
15 KiB
Verilog
`timescale 1ns/1ps
|
|
|
|
/*
|
|
This file contains simulation models for GreenPAK cells which are possible to fully model using synthesizeable
|
|
behavioral Verilog constructs only.
|
|
*/
|
|
|
|
module GP_2LUT(input IN0, IN1, output OUT);
|
|
parameter [3:0] INIT = 0;
|
|
assign OUT = INIT[{IN1, IN0}];
|
|
endmodule
|
|
|
|
module GP_3LUT(input IN0, IN1, IN2, output OUT);
|
|
parameter [7:0] INIT = 0;
|
|
assign OUT = INIT[{IN2, IN1, IN0}];
|
|
endmodule
|
|
|
|
module GP_4LUT(
|
|
input wire IN0,
|
|
input wire IN1,
|
|
input wire IN2,
|
|
input wire IN3,
|
|
output wire OUT);
|
|
|
|
parameter [15:0] INIT = 0;
|
|
assign OUT = INIT[{IN3, IN2, IN1, IN0}];
|
|
endmodule
|
|
|
|
module GP_CLKBUF(input wire IN, output wire OUT);
|
|
assign OUT = IN;
|
|
endmodule
|
|
|
|
module GP_COUNT14(input CLK, input wire RST, output reg OUT);
|
|
|
|
parameter RESET_MODE = "RISING";
|
|
|
|
parameter COUNT_TO = 14'h1;
|
|
parameter CLKIN_DIVIDE = 1;
|
|
|
|
reg[13:0] count = COUNT_TO;
|
|
|
|
initial begin
|
|
if(CLKIN_DIVIDE != 1) begin
|
|
$display("ERROR: CLKIN_DIVIDE values other than 1 not implemented");
|
|
$finish;
|
|
end
|
|
end
|
|
|
|
//Combinatorially output underflow flag whenever we wrap low
|
|
always @(*) begin
|
|
OUT <= (count == 14'h0);
|
|
end
|
|
|
|
//POR or SYSRST reset value is COUNT_TO. Datasheet is unclear but conversations w/ Silego confirm.
|
|
//Runtime reset value is clearly 0 except in count/FSM cells where it's configurable but we leave at 0 for now.
|
|
generate
|
|
case(RESET_MODE)
|
|
|
|
"RISING": begin
|
|
always @(posedge CLK, posedge RST) begin
|
|
if(RST)
|
|
count <= 0;
|
|
else begin
|
|
count <= count - 1'd1;
|
|
if(count == 0)
|
|
count <= COUNT_TO;
|
|
end
|
|
end
|
|
end
|
|
|
|
"FALLING": begin
|
|
always @(posedge CLK, negedge RST) begin
|
|
if(!RST)
|
|
count <= 0;
|
|
else begin
|
|
count <= count - 1'd1;
|
|
if(count == 0)
|
|
count <= COUNT_TO;
|
|
end
|
|
end
|
|
end
|
|
|
|
"BOTH": begin
|
|
initial begin
|
|
$display("Both-edge reset mode for GP_COUNT14 not implemented");
|
|
$finish;
|
|
end
|
|
end
|
|
|
|
"LEVEL": begin
|
|
always @(posedge CLK, posedge RST) begin
|
|
if(RST)
|
|
count <= 0;
|
|
|
|
else begin
|
|
count <= count - 1'd1;
|
|
if(count == 0)
|
|
count <= COUNT_TO;
|
|
end
|
|
end
|
|
end
|
|
|
|
default: begin
|
|
initial begin
|
|
$display("Invalid RESET_MODE on GP_COUNT14");
|
|
$finish;
|
|
end
|
|
end
|
|
|
|
endcase
|
|
endgenerate
|
|
|
|
endmodule
|
|
|
|
module GP_COUNT14_ADV(input CLK, input RST, output reg OUT,
|
|
input UP, input KEEP, output reg[7:0] POUT);
|
|
|
|
parameter RESET_MODE = "RISING";
|
|
parameter RESET_VALUE = "ZERO";
|
|
|
|
parameter COUNT_TO = 14'h1;
|
|
parameter CLKIN_DIVIDE = 1;
|
|
|
|
initial begin
|
|
if(CLKIN_DIVIDE != 1) begin
|
|
$display("ERROR: CLKIN_DIVIDE values other than 1 not implemented");
|
|
$finish;
|
|
end
|
|
end
|
|
|
|
reg[13:0] count = COUNT_TO;
|
|
|
|
//Combinatorially output underflow flag whenever we wrap low
|
|
always @(*) begin
|
|
if(UP)
|
|
OUT <= (count == 14'h3fff);
|
|
else
|
|
OUT <= (count == 14'h0);
|
|
POUT <= count[7:0];
|
|
end
|
|
|
|
//POR or SYSRST reset value is COUNT_TO. Datasheet is unclear but conversations w/ Silego confirm.
|
|
//Runtime reset value is clearly 0 except in count/FSM cells where it's configurable but we leave at 0 for now.
|
|
generate
|
|
case(RESET_MODE)
|
|
|
|
"RISING": begin
|
|
always @(posedge CLK, posedge RST) begin
|
|
|
|
//Resets
|
|
if(RST) begin
|
|
if(RESET_VALUE == "ZERO")
|
|
count <= 0;
|
|
else
|
|
count <= COUNT_TO;
|
|
end
|
|
|
|
else if(KEEP) begin
|
|
end
|
|
else if(UP) begin
|
|
count <= count + 1'd1;
|
|
if(count == 14'h3fff)
|
|
count <= COUNT_TO;
|
|
end
|
|
else begin
|
|
count <= count - 1'd1;
|
|
|
|
if(count == 0)
|
|
count <= COUNT_TO;
|
|
end
|
|
|
|
end
|
|
end
|
|
|
|
"FALLING": begin
|
|
always @(posedge CLK, negedge RST) begin
|
|
|
|
//Resets
|
|
if(!RST) begin
|
|
if(RESET_VALUE == "ZERO")
|
|
count <= 0;
|
|
else
|
|
count <= COUNT_TO;
|
|
end
|
|
|
|
else if(KEEP) begin
|
|
end
|
|
else if(UP) begin
|
|
count <= count + 1'd1;
|
|
if(count == 14'h3fff)
|
|
count <= COUNT_TO;
|
|
end
|
|
else begin
|
|
count <= count - 1'd1;
|
|
|
|
if(count == 0)
|
|
count <= COUNT_TO;
|
|
end
|
|
|
|
end
|
|
end
|
|
|
|
"BOTH": begin
|
|
initial begin
|
|
$display("Both-edge reset mode for GP_COUNT14_ADV not implemented");
|
|
$finish;
|
|
end
|
|
end
|
|
|
|
"LEVEL": begin
|
|
always @(posedge CLK, posedge RST) begin
|
|
|
|
//Resets
|
|
if(RST) begin
|
|
if(RESET_VALUE == "ZERO")
|
|
count <= 0;
|
|
else
|
|
count <= COUNT_TO;
|
|
end
|
|
|
|
else begin
|
|
|
|
if(KEEP) begin
|
|
end
|
|
else if(UP) begin
|
|
count <= count + 1'd1;
|
|
if(count == 14'h3fff)
|
|
count <= COUNT_TO;
|
|
end
|
|
else begin
|
|
count <= count - 1'd1;
|
|
|
|
if(count == 0)
|
|
count <= COUNT_TO;
|
|
end
|
|
|
|
end
|
|
|
|
end
|
|
end
|
|
|
|
default: begin
|
|
initial begin
|
|
$display("Invalid RESET_MODE on GP_COUNT14_ADV");
|
|
$finish;
|
|
end
|
|
end
|
|
|
|
endcase
|
|
endgenerate
|
|
|
|
endmodule
|
|
|
|
module GP_COUNT8_ADV(input CLK, input RST, output reg OUT,
|
|
input UP, input KEEP, output reg[7:0] POUT);
|
|
|
|
parameter RESET_MODE = "RISING";
|
|
parameter RESET_VALUE = "ZERO";
|
|
|
|
parameter COUNT_TO = 8'h1;
|
|
parameter CLKIN_DIVIDE = 1;
|
|
|
|
reg[7:0] count = COUNT_TO;
|
|
|
|
initial begin
|
|
if(CLKIN_DIVIDE != 1) begin
|
|
$display("ERROR: CLKIN_DIVIDE values other than 1 not implemented");
|
|
$finish;
|
|
end
|
|
end
|
|
|
|
//Combinatorially output underflow flag whenever we wrap low
|
|
always @(*) begin
|
|
if(UP)
|
|
OUT <= (count == 8'hff);
|
|
else
|
|
OUT <= (count == 8'h0);
|
|
POUT <= count;
|
|
end
|
|
|
|
//POR or SYSRST reset value is COUNT_TO. Datasheet is unclear but conversations w/ Silego confirm.
|
|
//Runtime reset value is clearly 0 except in count/FSM cells where it's configurable but we leave at 0 for now.
|
|
generate
|
|
case(RESET_MODE)
|
|
|
|
"RISING": begin
|
|
always @(posedge CLK, posedge RST) begin
|
|
|
|
//Resets
|
|
if(RST) begin
|
|
if(RESET_VALUE == "ZERO")
|
|
count <= 0;
|
|
else
|
|
count <= COUNT_TO;
|
|
end
|
|
|
|
//Main counter
|
|
else if(KEEP) begin
|
|
end
|
|
else if(UP) begin
|
|
count <= count + 1'd1;
|
|
if(count == 8'hff)
|
|
count <= COUNT_TO;
|
|
end
|
|
else begin
|
|
count <= count - 1'd1;
|
|
|
|
if(count == 0)
|
|
count <= COUNT_TO;
|
|
end
|
|
|
|
end
|
|
end
|
|
|
|
"FALLING": begin
|
|
always @(posedge CLK, negedge RST) begin
|
|
|
|
//Resets
|
|
if(!RST) begin
|
|
if(RESET_VALUE == "ZERO")
|
|
count <= 0;
|
|
else
|
|
count <= COUNT_TO;
|
|
end
|
|
|
|
//Main counter
|
|
else if(KEEP) begin
|
|
end
|
|
else if(UP) begin
|
|
count <= count + 1'd1;
|
|
if(count == 8'hff)
|
|
count <= COUNT_TO;
|
|
end
|
|
else begin
|
|
count <= count - 1'd1;
|
|
|
|
if(count == 0)
|
|
count <= COUNT_TO;
|
|
end
|
|
|
|
end
|
|
end
|
|
|
|
"BOTH": begin
|
|
initial begin
|
|
$display("Both-edge reset mode for GP_COUNT8_ADV not implemented");
|
|
$finish;
|
|
end
|
|
end
|
|
|
|
"LEVEL": begin
|
|
always @(posedge CLK, posedge RST) begin
|
|
|
|
//Resets
|
|
if(RST) begin
|
|
if(RESET_VALUE == "ZERO")
|
|
count <= 0;
|
|
else
|
|
count <= COUNT_TO;
|
|
end
|
|
|
|
else begin
|
|
|
|
if(KEEP) begin
|
|
end
|
|
else if(UP) begin
|
|
count <= count + 1'd1;
|
|
if(count == 8'hff)
|
|
count <= COUNT_TO;
|
|
end
|
|
else begin
|
|
count <= count - 1'd1;
|
|
|
|
if(count == 0)
|
|
count <= COUNT_TO;
|
|
end
|
|
end
|
|
|
|
end
|
|
end
|
|
|
|
default: begin
|
|
initial begin
|
|
$display("Invalid RESET_MODE on GP_COUNT8_ADV");
|
|
$finish;
|
|
end
|
|
end
|
|
|
|
endcase
|
|
endgenerate
|
|
|
|
endmodule
|
|
|
|
module GP_COUNT8(
|
|
input wire CLK,
|
|
input wire RST,
|
|
output reg OUT,
|
|
output reg[7:0] POUT);
|
|
|
|
parameter RESET_MODE = "RISING";
|
|
|
|
parameter COUNT_TO = 8'h1;
|
|
parameter CLKIN_DIVIDE = 1;
|
|
|
|
initial begin
|
|
if(CLKIN_DIVIDE != 1) begin
|
|
$display("ERROR: CLKIN_DIVIDE values other than 1 not implemented");
|
|
$finish;
|
|
end
|
|
end
|
|
|
|
reg[7:0] count = COUNT_TO;
|
|
|
|
//Combinatorially output underflow flag whenever we wrap low
|
|
always @(*) begin
|
|
OUT <= (count == 8'h0);
|
|
POUT <= count;
|
|
end
|
|
|
|
//POR or SYSRST reset value is COUNT_TO. Datasheet is unclear but conversations w/ Silego confirm.
|
|
//Runtime reset value is clearly 0 except in count/FSM cells where it's configurable but we leave at 0 for now.
|
|
generate
|
|
case(RESET_MODE)
|
|
|
|
"RISING": begin
|
|
always @(posedge CLK, posedge RST) begin
|
|
if(RST)
|
|
count <= 0;
|
|
else begin
|
|
count <= count - 1'd1;
|
|
if(count == 0)
|
|
count <= COUNT_TO;
|
|
end
|
|
end
|
|
end
|
|
|
|
"FALLING": begin
|
|
always @(posedge CLK, negedge RST) begin
|
|
if(!RST)
|
|
count <= 0;
|
|
else begin
|
|
count <= count - 1'd1;
|
|
if(count == 0)
|
|
count <= COUNT_TO;
|
|
end
|
|
end
|
|
end
|
|
|
|
"BOTH": begin
|
|
initial begin
|
|
$display("Both-edge reset mode for GP_COUNT8 not implemented");
|
|
$finish;
|
|
end
|
|
end
|
|
|
|
"LEVEL": begin
|
|
always @(posedge CLK, posedge RST) begin
|
|
if(RST)
|
|
count <= 0;
|
|
|
|
else begin
|
|
count <= count - 1'd1;
|
|
if(count == 0)
|
|
count <= COUNT_TO;
|
|
end
|
|
end
|
|
end
|
|
|
|
default: begin
|
|
initial begin
|
|
$display("Invalid RESET_MODE on GP_COUNT8");
|
|
$finish;
|
|
end
|
|
end
|
|
|
|
endcase
|
|
endgenerate
|
|
|
|
endmodule
|
|
|
|
module GP_DCMPREF(output reg[7:0]OUT);
|
|
parameter[7:0] REF_VAL = 8'h00;
|
|
initial OUT = REF_VAL;
|
|
endmodule
|
|
|
|
module GP_DCMPMUX(input[1:0] SEL, input[7:0] IN0, input[7:0] IN1, input[7:0] IN2, input[7:0] IN3, output reg[7:0] OUTA, output reg[7:0] OUTB);
|
|
|
|
always @(*) begin
|
|
case(SEL)
|
|
2'd00: begin
|
|
OUTA <= IN0;
|
|
OUTB <= IN3;
|
|
end
|
|
|
|
2'd01: begin
|
|
OUTA <= IN1;
|
|
OUTB <= IN2;
|
|
end
|
|
|
|
2'd02: begin
|
|
OUTA <= IN2;
|
|
OUTB <= IN1;
|
|
end
|
|
|
|
2'd03: begin
|
|
OUTA <= IN3;
|
|
OUTB <= IN0;
|
|
end
|
|
|
|
endcase
|
|
end
|
|
endmodule
|
|
|
|
module GP_DELAY(input IN, output reg OUT);
|
|
|
|
parameter DELAY_STEPS = 1;
|
|
parameter GLITCH_FILTER = 0;
|
|
|
|
initial OUT = 0;
|
|
|
|
generate
|
|
|
|
if(GLITCH_FILTER) begin
|
|
initial begin
|
|
$display("ERROR: GP_DELAY glitch filter mode not implemented");
|
|
$finish;
|
|
end
|
|
end
|
|
|
|
//TODO: These delays are PTV dependent! For now, hard code 3v3 timing
|
|
//Change simulation-mode delay depending on global Vdd range (how to specify this?)
|
|
always @(*) begin
|
|
case(DELAY_STEPS)
|
|
1: #166 OUT = IN;
|
|
2: #318 OUT = IN;
|
|
2: #471 OUT = IN;
|
|
3: #622 OUT = IN;
|
|
default: begin
|
|
$display("ERROR: GP_DELAY must have DELAY_STEPS in range [1,4]");
|
|
$finish;
|
|
end
|
|
endcase
|
|
end
|
|
|
|
endgenerate
|
|
|
|
endmodule
|
|
|
|
module GP_DFF(input D, CLK, output reg Q);
|
|
parameter [0:0] INIT = 1'bx;
|
|
initial Q = INIT;
|
|
always @(posedge CLK) begin
|
|
Q <= D;
|
|
end
|
|
endmodule
|
|
|
|
module GP_DFFI(input D, CLK, output reg nQ);
|
|
parameter [0:0] INIT = 1'bx;
|
|
initial nQ = INIT;
|
|
always @(posedge CLK) begin
|
|
nQ <= ~D;
|
|
end
|
|
endmodule
|
|
|
|
module GP_DFFR(input D, CLK, nRST, output reg Q);
|
|
parameter [0:0] INIT = 1'bx;
|
|
initial Q = INIT;
|
|
always @(posedge CLK, negedge nRST) begin
|
|
if (!nRST)
|
|
Q <= 1'b0;
|
|
else
|
|
Q <= D;
|
|
end
|
|
endmodule
|
|
|
|
module GP_DFFRI(input D, CLK, nRST, output reg nQ);
|
|
parameter [0:0] INIT = 1'bx;
|
|
initial nQ = INIT;
|
|
always @(posedge CLK, negedge nRST) begin
|
|
if (!nRST)
|
|
nQ <= 1'b1;
|
|
else
|
|
nQ <= ~D;
|
|
end
|
|
endmodule
|
|
|
|
module GP_DFFS(input D, CLK, nSET, output reg Q);
|
|
parameter [0:0] INIT = 1'bx;
|
|
initial Q = INIT;
|
|
always @(posedge CLK, negedge nSET) begin
|
|
if (!nSET)
|
|
Q <= 1'b1;
|
|
else
|
|
Q <= D;
|
|
end
|
|
endmodule
|
|
|
|
module GP_DFFSI(input D, CLK, nSET, output reg nQ);
|
|
parameter [0:0] INIT = 1'bx;
|
|
initial nQ = INIT;
|
|
always @(posedge CLK, negedge nSET) begin
|
|
if (!nSET)
|
|
nQ <= 1'b0;
|
|
else
|
|
nQ <= ~D;
|
|
end
|
|
endmodule
|
|
|
|
module GP_DFFSR(input D, CLK, nSR, output reg Q);
|
|
parameter [0:0] INIT = 1'bx;
|
|
parameter [0:0] SRMODE = 1'bx;
|
|
initial Q = INIT;
|
|
always @(posedge CLK, negedge nSR) begin
|
|
if (!nSR)
|
|
Q <= SRMODE;
|
|
else
|
|
Q <= D;
|
|
end
|
|
endmodule
|
|
|
|
module GP_DFFSRI(input D, CLK, nSR, output reg nQ);
|
|
parameter [0:0] INIT = 1'bx;
|
|
parameter [0:0] SRMODE = 1'bx;
|
|
initial nQ = INIT;
|
|
always @(posedge CLK, negedge nSR) begin
|
|
if (!nSR)
|
|
nQ <= ~SRMODE;
|
|
else
|
|
nQ <= ~D;
|
|
end
|
|
endmodule
|
|
|
|
module GP_DLATCH(input D, input nCLK, output reg Q);
|
|
parameter [0:0] INIT = 1'bx;
|
|
initial Q = INIT;
|
|
always @(*) begin
|
|
if(!nCLK)
|
|
Q <= D;
|
|
end
|
|
endmodule
|
|
|
|
module GP_DLATCHI(input D, input nCLK, output reg nQ);
|
|
parameter [0:0] INIT = 1'bx;
|
|
initial nQ = INIT;
|
|
always @(*) begin
|
|
if(!nCLK)
|
|
nQ <= ~D;
|
|
end
|
|
endmodule
|
|
|
|
module GP_DLATCHR(input D, input nCLK, input nRST, output reg Q);
|
|
parameter [0:0] INIT = 1'bx;
|
|
initial Q = INIT;
|
|
always @(*) begin
|
|
if(!nRST)
|
|
Q <= 1'b0;
|
|
else if(!nCLK)
|
|
Q <= D;
|
|
end
|
|
endmodule
|
|
|
|
module GP_DLATCHRI(input D, input nCLK, input nRST, output reg nQ);
|
|
parameter [0:0] INIT = 1'bx;
|
|
initial nQ = INIT;
|
|
always @(*) begin
|
|
if(!nRST)
|
|
nQ <= 1'b1;
|
|
else if(!nCLK)
|
|
nQ <= ~D;
|
|
end
|
|
endmodule
|
|
|
|
module GP_DLATCHS(input D, input nCLK, input nSET, output reg Q);
|
|
parameter [0:0] INIT = 1'bx;
|
|
initial Q = INIT;
|
|
always @(*) begin
|
|
if(!nSET)
|
|
Q <= 1'b1;
|
|
else if(!nCLK)
|
|
Q <= D;
|
|
end
|
|
endmodule
|
|
|
|
module GP_DLATCHSI(input D, input nCLK, input nSET, output reg nQ);
|
|
parameter [0:0] INIT = 1'bx;
|
|
initial nQ = INIT;
|
|
always @(*) begin
|
|
if(!nSET)
|
|
nQ <= 1'b0;
|
|
else if(!nCLK)
|
|
nQ <= ~D;
|
|
end
|
|
endmodule
|
|
|
|
module GP_DLATCHSR(input D, input nCLK, input nSR, output reg Q);
|
|
parameter [0:0] INIT = 1'bx;
|
|
parameter[0:0] SRMODE = 1'bx;
|
|
initial Q = INIT;
|
|
always @(*) begin
|
|
if(!nSR)
|
|
Q <= SRMODE;
|
|
else if(!nCLK)
|
|
Q <= D;
|
|
end
|
|
endmodule
|
|
|
|
module GP_DLATCHSRI(input D, input nCLK, input nSR, output reg nQ);
|
|
parameter [0:0] INIT = 1'bx;
|
|
parameter[0:0] SRMODE = 1'bx;
|
|
initial nQ = INIT;
|
|
always @(*) begin
|
|
if(!nSR)
|
|
nQ <= ~SRMODE;
|
|
else if(!nCLK)
|
|
nQ <= ~D;
|
|
end
|
|
endmodule
|
|
|
|
module GP_IBUF(input IN, output OUT);
|
|
assign OUT = IN;
|
|
endmodule
|
|
|
|
module GP_IOBUF(input IN, input OE, output OUT, inout IO);
|
|
assign OUT = IO;
|
|
assign IO = OE ? IN : 1'bz;
|
|
endmodule
|
|
|
|
module GP_INV(input IN, output OUT);
|
|
assign OUT = ~IN;
|
|
endmodule
|
|
|
|
module GP_OBUF(input IN, output OUT);
|
|
assign OUT = IN;
|
|
endmodule
|
|
|
|
module GP_OBUFT(input IN, input OE, output OUT);
|
|
assign OUT = OE ? IN : 1'bz;
|
|
endmodule
|
|
|
|
module GP_PGEN(input wire nRST, input wire CLK, output reg OUT);
|
|
initial OUT = 0;
|
|
parameter PATTERN_DATA = 16'h0;
|
|
parameter PATTERN_LEN = 5'd16;
|
|
|
|
localparam COUNT_MAX = PATTERN_LEN - 1'h1;
|
|
|
|
reg[3:0] count = 0;
|
|
always @(posedge CLK, negedge nRST) begin
|
|
|
|
if(!nRST)
|
|
count <= 0;
|
|
|
|
else begin
|
|
count <= count - 1'h1;
|
|
if(count == 0)
|
|
count <= COUNT_MAX;
|
|
end
|
|
end
|
|
|
|
always @(*)
|
|
OUT = PATTERN_DATA[count];
|
|
|
|
endmodule
|
|
|
|
module GP_SHREG(input nRST, input CLK, input IN, output OUTA, output OUTB);
|
|
|
|
parameter OUTA_TAP = 1;
|
|
parameter OUTA_INVERT = 0;
|
|
parameter OUTB_TAP = 1;
|
|
|
|
reg[15:0] shreg = 0;
|
|
|
|
always @(posedge CLK, negedge nRST) begin
|
|
|
|
if(!nRST)
|
|
shreg = 0;
|
|
|
|
else
|
|
shreg <= {shreg[14:0], IN};
|
|
|
|
end
|
|
|
|
assign OUTA = (OUTA_INVERT) ? ~shreg[OUTA_TAP - 1] : shreg[OUTA_TAP - 1];
|
|
assign OUTB = shreg[OUTB_TAP - 1];
|
|
|
|
endmodule
|
|
|
|
module GP_VDD(output OUT);
|
|
assign OUT = 1;
|
|
endmodule
|
|
|
|
module GP_VSS(output OUT);
|
|
assign OUT = 0;
|
|
endmodule
|