1454 lines
81 KiB
XML
Executable File
1454 lines
81 KiB
XML
Executable File
<!--
|
|
Flagship Heterogeneous Architecture (No Carry Chains) for VTR 7.0.
|
|
|
|
- 40 nm technology
|
|
- General purpose logic block:
|
|
K = 6, N = 10, fracturable 6 LUTs (can operate as one 6-LUT or two 5-LUTs with all 5 inputs shared)
|
|
with optionally registered outputs
|
|
- Memory size 32 Kbits, memory aspect ratios vary from a data width of 1 to data width of 64.
|
|
Height = 6, found on every (8n+2)th column
|
|
- Multiplier modes: one 36x36, two 18x18, each 18x18 can also operate as two 9x9.
|
|
Height = 4, found on every (8n+6)th column
|
|
- Routing architecture: L = 4, fc_in = 0.15, Fc_out = 0.1
|
|
|
|
Details on Modelling:
|
|
|
|
The electrical design of the architecture described here is NOT from an
|
|
optimized, SPICED architecture. Instead, we attempt to create a reasonable
|
|
architecture file by using an existing commercial FPGA to approximate the area,
|
|
delay, and power of the underlying components. This is combined with a reasonable 40 nm
|
|
model of wiring and circuit design for low-level routing components, where available.
|
|
The resulting architecture has delays that roughly match a commercial 40 nm FPGA, but also
|
|
has wiring electrical parameters that allow the wire lengths and switch patterns to be
|
|
modified and you will still get reasonable delay results for the new architecture.
|
|
The following describes, in detail, how we obtained the various electrical values for this
|
|
architecture.
|
|
|
|
Rmin for nmos and pmos, routing buffer sizes, and I/O pad delays are from the ifar
|
|
architecture created by Ian Kuon: K06 N10 45nm fc 0.15 area-delay optimized architecture.
|
|
(n10k06l04.fc15.area1delay1.cmos45nm.bptm.cmos45nm.xml)
|
|
This routing architecture was optimized for 45 nm, and we have scaled it linearly to 40 nm to
|
|
match the overall target (a 40 nm FPGA).
|
|
|
|
We obtain delay numbers by measuring delays of routing, soft logic blocks,
|
|
memories, and multipliers from test circuits on a Stratix IV GX device
|
|
(EP4SGX230DF29C2X, i.e. fastest speed grade). For routing, we took the average delay of H4 and V4
|
|
wires. Rmetal and Cmetal values for the routing wires were obtained from work done by Charles
|
|
Chiasson. We use a 96 nm half-pitch (corresponding to mid-level metal stack 40 nm routing) and
|
|
take the R and C data from the ITRS roadmap.
|
|
|
|
For the general purpose logic block, we assume that the area and delays of the Stratix IV
|
|
crossbar is close enough to the crossbar modelled here. We use 40 inputs and 20 feedback lines in
|
|
the cluster and a full crossbar, leading to 60:1 multiplexers in front of each BLE input.
|
|
Stratix IV uses 52 inputs and 20 feedback lines, but only a half-populated crossbar, leading to
|
|
36:1 multiplexers. We require 60 such multiplexers, while Stratix IV requires 88 for its more
|
|
complex fracturable BLEs + the extra control signals. We justify this rough approximation as follows:
|
|
The Stratix IV crossbar has more inputs (72 vs. 60) and
|
|
outputs (88 vs. 60) than our full crossbar which should increase its area and delay, but the
|
|
Stratix IV crossbar is also 50% sparse (each mux is 36:1 instead of 60:1) which should reduce its
|
|
area and delay. The total number of crossbar switch points is roughly similar between the two
|
|
architectures (3160 for SIV and 3600 for the academic architecture below), so we use the area
|
|
& delay of the Stratix IV crossbar as a rough approximation of our crossbar.
|
|
|
|
For LUTs, we include LUT
|
|
delays measured from Stratix IV which is dependant on the input used (ie. some
|
|
LUT inputs are faster than others). The CAD tools at the time of VTR 7 does
|
|
not consider differences in LUT input delays.
|
|
|
|
Logic block area numbers obtained by scaling overall tile area of a 65nm
|
|
Stratix III device, (as given in Wong, Betz and Rose, FPGA 2011) to 40 nm, then subtracting out
|
|
routing area at a channel width of 300. We use a channel width of 300 because it can route
|
|
all the VTR 6.0 benchmark circuits with an approximately 20% safety margin, and is also close to the
|
|
total channel width of Stratix IV. Hence this channel width is close to the commercial practice of
|
|
choosing a width that provides high routability. The architecture can be routed at different channel
|
|
widths, but we estimate the tile size and hence the physical length of routing wires assuming
|
|
a channel width of 300.
|
|
|
|
Sanity checks employed:
|
|
1. We confirmed the routing buffer delay is ~1/3rd of total routing delay at L = 4. This matches
|
|
common electrical design.
|
|
|
|
|
|
Authors: Jason Luu, Jeff Goeders, Vaughn Betz
|
|
-->
|
|
|
|
<architecture>
|
|
|
|
<!--
|
|
ODIN II specific config begins
|
|
Describes the types of user-specified netlist blocks (in blif, this corresponds to
|
|
".model [type_of_block]") that this architecture supports.
|
|
|
|
Note: Basic LUTs, I/Os, and flip-flops are not included here as there are
|
|
already special structures in blif (.names, .input, .output, and .latch)
|
|
that describe them.
|
|
-->
|
|
<models>
|
|
<model name="io">
|
|
<input_ports>
|
|
<port name="outpad"/>
|
|
</input_ports>
|
|
<output_ports>
|
|
<port name="inpad"/>
|
|
</output_ports>
|
|
</model>
|
|
<!--model name="multiply">
|
|
<input_ports>
|
|
<port name="a"/>
|
|
<port name="b"/>
|
|
</input_ports>
|
|
<output_ports>
|
|
<port name="out"/>
|
|
</output_ports>
|
|
</model>
|
|
|
|
<model name="single_port_ram">
|
|
<input_ports>
|
|
<port name="we"/--> <!-- control -->
|
|
<!--port name="addr"/--> <!-- address lines -->
|
|
<!--port name="data"/--> <!-- data lines can be broken down into smaller bit widths minimum size 1 -->
|
|
<!--port name="clk" is_clock="1"/--> <!-- memories are often clocked -->
|
|
<!--/input_ports>
|
|
<output_ports-->
|
|
<!--port name="out"/--> <!-- output can be broken down into smaller bit widths minimum size 1 -->
|
|
<!--/output_ports>
|
|
</model>
|
|
|
|
<model name="dual_port_ram">
|
|
<input_ports-->
|
|
<!--port name="we1"/--> <!-- write enable -->
|
|
<!--port name="we2"/--> <!-- write enable -->
|
|
<!--port name="addr1"/--> <!-- address lines -->
|
|
<!--port name="addr2"/--> <!-- address lines -->
|
|
<!--port name="data1"/--> <!-- data lines can be broken down into smaller bit widths minimum size 1 -->
|
|
<!--port name="data2"/--> <!-- data lines can be broken down into smaller bit widths minimum size 1 -->
|
|
<!--port name="clk" is_clock="1"/--> <!-- memories are often clocked -->
|
|
<!--/input_ports>
|
|
<output_ports-->
|
|
<!--port name="out1"/--> <!-- output can be broken down into smaller bit widths minimum size 1 -->
|
|
<!--port name="out2"/--> <!-- output can be broken down into smaller bit widths minimum size 1 -->
|
|
<!--/output_ports>
|
|
</model-->
|
|
|
|
</models>
|
|
<!-- ODIN II specific config ends -->
|
|
|
|
<!-- Physical descriptions begin -->
|
|
<layout auto="1.0"/>
|
|
<!--layout width="2" height="2"/-->
|
|
|
|
<!--mrFPGA_settings-->
|
|
<!-- below is the timing parameters for a single memristor device (or so called RRAM) -->
|
|
<!--mrFPGA R="1e3" C="2.24e-17" Tdel="0"-->
|
|
<!-- below is the timing parameters for the buffers to insert in channels -->
|
|
<!--buffer R="193.5" Cin="3.66e-15" Cout="3.56e-15" Tdel="6.14e-12"/-->
|
|
<!--cblock R_opin_cblock="193.5" T_opin_cblock="6.14e-12"/-->
|
|
<!--/mrFPGA-->
|
|
<!--/mrFPGA_settings-->
|
|
|
|
<spice_settings>
|
|
<parameters>
|
|
<options sim_temp="25" post="off" captab="off" fast="on"/>
|
|
<monte_carlo mc_sim="off" num_mc_points="2" cmos_variation="off" rram_variation="off">
|
|
<cmos abs_variation="0.1" num_sigma="3"/>
|
|
<rram abs_variation="0.1" num_sigma="3"/>
|
|
</monte_carlo>
|
|
<measure sim_num_clock_cycle="auto" accuracy="1e-13" accuracy_type="abs">
|
|
<slew>
|
|
<rise upper_thres_pct="0.95" lower_thres_pct="0.05"/>
|
|
<fall upper_thres_pct="0.05" lower_thres_pct="0.95"/>
|
|
</slew>
|
|
<delay>
|
|
<rise input_thres_pct="0.5" output_thres_pct="0.5"/>
|
|
<fall input_thres_pct="0.5" output_thres_pct="0.5"/>
|
|
</delay>
|
|
</measure>
|
|
<stimulate>
|
|
<clock op_freq="200e6" sim_slack="0.2" prog_freq="10e6">
|
|
<rise slew_time="20e-12" slew_type="abs"/>
|
|
<fall slew_time="20e-12" slew_type="abs"/>
|
|
</clock>
|
|
<input>
|
|
<rise slew_time="25e-12" slew_type="abs"/>
|
|
<fall slew_time="25e-12" slew_type="abs"/>
|
|
</input>
|
|
</stimulate>
|
|
</parameters>
|
|
<tech_lib lib_type="academia" transistor_type="TOP_TT" lib_path="OPENFPGAPATH/vpr7_x2p/tech/PTM_45nm/45nm.pm" nominal_vdd="1.0" io_vdd="2.5"/>
|
|
<transistors pn_ratio="2" model_ref="M">
|
|
<nmos model_name="nmos" chan_length="45e-9" min_width="140e-9"/>
|
|
<pmos model_name="pmos" chan_length="45e-9" min_width="140e-9"/>
|
|
<io_nmos model_name="nch_25" chan_length="270e-9" min_width="320e-9"/>
|
|
<io_pmos model_name="pch_25" chan_length="270e-9" min_width="320e-9"/>
|
|
</transistors>
|
|
<module_circuit_models>
|
|
<circuit_model type="inv_buf" name="INVTX1" prefix="INVTX1" is_default="1">
|
|
<design_technology type="cmos" topology="inverter" size="1" tapered="off"/>
|
|
<port type="input" prefix="in" size="1"/>
|
|
<port type="output" prefix="out" size="1"/>
|
|
<delay_matrix type="rise" in_port="in" out_port="out">
|
|
10e-12
|
|
</delay_matrix>
|
|
<delay_matrix type="fall" in_port="in" out_port="out">
|
|
10e-12
|
|
</delay_matrix>
|
|
</circuit_model>
|
|
<circuit_model type="inv_buf" name="buf4" prefix="buf4" is_default="0">
|
|
<design_technology type="cmos" topology="buffer" size="1" tapered="on" tap_drive_level="2" f_per_stage="4"/>
|
|
<port type="input" prefix="in" size="1"/>
|
|
<port type="output" prefix="out" size="1"/>
|
|
<delay_matrix type="rise" in_port="in" out_port="out">
|
|
10e-12
|
|
</delay_matrix>
|
|
<delay_matrix type="fall" in_port="in" out_port="out">
|
|
10e-12
|
|
</delay_matrix>
|
|
</circuit_model>
|
|
<circuit_model type="inv_buf" name="tap_buf4" prefix="tap_buf4" is_default="0">
|
|
<design_technology type="cmos" topology="buffer" size="1" tapered="on" tap_drive_level="3" f_per_stage="4"/>
|
|
<port type="input" prefix="in" size="1"/>
|
|
<port type="output" prefix="out" size="1"/>
|
|
<delay_matrix type="rise" in_port="in" out_port="out">
|
|
10e-12
|
|
</delay_matrix>
|
|
<delay_matrix type="fall" in_port="in" out_port="out">
|
|
10e-12
|
|
</delay_matrix>
|
|
</circuit_model>
|
|
<circuit_model type="pass_gate" name="TGATE" prefix="TGATE" is_default="1">
|
|
<design_technology type="cmos" topology="transmission_gate" nmos_size="1" pmos_size="2"/>
|
|
<input_buffer exist="off"/>
|
|
<output_buffer exist="off"/>
|
|
<port type="input" prefix="in" size="1"/>
|
|
<port type="input" prefix="sel" size="1"/>
|
|
<port type="input" prefix="selb" size="1"/>
|
|
<port type="output" prefix="out" size="1"/>
|
|
<delay_matrix type="rise" in_port="in sel selb" out_port="out">
|
|
10e-12 0e-12 0e-12
|
|
</delay_matrix>
|
|
<delay_matrix type="fall" in_port="in sel selb" out_port="out">
|
|
10e-12 0e-12 0e-12
|
|
</delay_matrix>
|
|
</circuit_model>
|
|
<circuit_model type="chan_wire" name="chan_segment" prefix="track_seg" is_default="1">
|
|
<design_technology type="cmos"/>
|
|
<input_buffer exist="off"/>
|
|
<output_buffer exist="off"/>
|
|
<port type="input" prefix="in" size="1"/>
|
|
<port type="output" prefix="out" size="1"/>
|
|
<wire_param model_type="pie" res_val="101" cap_val="22.5e-15" level="1"/> <!-- model_type could be T, res_val and cap_val DON'T CARE -->
|
|
</circuit_model>
|
|
<circuit_model type="wire" name="direct_interc" prefix="direct_interc" is_default="1">
|
|
<design_technology type="cmos"/>
|
|
<input_buffer exist="off"/>
|
|
<output_buffer exist="off"/>
|
|
<port type="input" prefix="in" size="1"/>
|
|
<port type="output" prefix="out" size="1"/>
|
|
<wire_param model_type="pie" res_val="0" cap_val="0" level="1"/> <!-- model_type could be T, res_val cap_val should be defined -->
|
|
</circuit_model>
|
|
<circuit_model type="mux" name="mux_2level" prefix="mux_2level" is_default="1" dump_structural_verilog="true">
|
|
<design_technology type="cmos" structure="multi-level" num_level="2"/>
|
|
<input_buffer exist="on" circuit_model_name="INVTX1"/>
|
|
<output_buffer exist="on" circuit_model_name="INVTX1"/>
|
|
<!--mux2to1 subckt_name="mux2to1"/-->
|
|
<pass_gate_logic circuit_model_name="TGATE"/>
|
|
<port type="input" prefix="in" size="1"/>
|
|
<port type="output" prefix="out" size="1"/>
|
|
<port type="sram" prefix="sram" size="1"/>
|
|
</circuit_model>
|
|
<circuit_model type="mux" name="mux_2level_tapbuf" prefix="mux_2level_tapbuf" dump_structural_verilog="true">
|
|
<design_technology type="cmos" structure="multi-level" num_level="2"/>
|
|
<input_buffer exist="on" circuit_model_name="INVTX1"/>
|
|
<output_buffer exist="on" circuit_model_name="tap_buf4"/>
|
|
<!--mux2to1 subckt_name="mux2to1"/-->
|
|
<pass_gate_logic circuit_model_name="TGATE"/>
|
|
<port type="input" prefix="in" size="1"/>
|
|
<port type="output" prefix="out" size="1"/>
|
|
<port type="sram" prefix="sram" size="1"/>
|
|
</circuit_model>
|
|
|
|
<circuit_model type="mux" name="mux_1level_tapbuf" prefix="mux_1level_tapbuf" dump_structural_verilog="true">
|
|
<design_technology type="cmos" structure="one-level"/>
|
|
<input_buffer exist="on" circuit_model_name="INVTX1"/>
|
|
<output_buffer exist="on" circuit_model_name="tap_buf4"/>
|
|
<!--mux2to1 subckt_name="mux2to1"/-->
|
|
<pass_gate_logic circuit_model_name="TGATE"/>
|
|
<port type="input" prefix="in" size="1"/>
|
|
<port type="output" prefix="out" size="1"/>
|
|
<port type="sram" prefix="sram" size="1"/>
|
|
</circuit_model>
|
|
<!--DFF subckt ports should be defined as <D> <Q> <CLK> <RESET> <SET> -->
|
|
<circuit_model type="ff" name="static_dff" prefix="dff" spice_netlist="OPENFPGAPATH/vpr7_x2p/vpr/SpiceNetlists/ff.sp" verilog_netlist="OPENFPGAPATH/vpr7_x2p/vpr/VerilogNetlists/ff.v">
|
|
<design_technology type="cmos"/>
|
|
<input_buffer exist="on" circuit_model_name="INVTX1"/>
|
|
<output_buffer exist="on" circuit_model_name="INVTX1"/>
|
|
<pass_gate_logic circuit_model_name="TGATE"/>
|
|
<port type="input" prefix="D" size="1"/>
|
|
<port type="input" prefix="Set" size="1" is_global="true" default_val="0" is_set="true"/>
|
|
<port type="input" prefix="Reset" size="1" is_global="true" default_val="0" is_reset="true"/>
|
|
<port type="output" prefix="Q" size="1"/>
|
|
<port type="clock" prefix="clk" size="1" is_global="true" default_val="0" />
|
|
</circuit_model>
|
|
<circuit_model type="lut" name="lut6" prefix="lut6" dump_structural_verilog="true">
|
|
<design_technology type="cmos"/>
|
|
<input_buffer exist="on" circuit_model_name="INVTX1"/>
|
|
<output_buffer exist="on" circuit_model_name="INVTX1"/>
|
|
<lut_input_buffer exist="on" circuit_model_name="buf4"/>
|
|
<pass_gate_logic circuit_model_name="TGATE"/>
|
|
<port type="input" prefix="in" size="6"/>
|
|
<port type="output" prefix="out" size="1"/>
|
|
<port type="sram" prefix="sram" size="64"/>
|
|
</circuit_model>
|
|
<circuit_model type="sram" name="sram6T" prefix="sram" spice_netlist="OPENFPGAPATH/vpr7_x2p/vpr/SpiceNetlists/sram.sp" verilog_netlist="OPENFPGAPATH/vpr7_x2p/vpr/VerilogNetlists/sram.v" >
|
|
<design_technology type="cmos"/>
|
|
<input_buffer exist="on" circuit_model_name="INVTX1"/>
|
|
<output_buffer exist="on" circuit_model_name="INVTX1"/>
|
|
<pass_gate_logic circuit_model_name="TGATE"/>
|
|
<port type="input" prefix="in" size="1"/>
|
|
<port type="output" prefix="out" size="2"/>
|
|
</circuit_model>
|
|
<circuit_model type="sram" name="sram6T_blwl" prefix="sram_blwl" spice_netlist="OPENFPGAPATH/vpr7_x2p/vpr/SpiceNetlists/sram.sp" verilog_netlist="OPENFPGAPATH/vpr7_x2p/vpr/VerilogNetlists/sram.v">
|
|
|
|
<design_technology type="cmos"/>
|
|
<input_buffer exist="on" circuit_model_name="INVTX1"/>
|
|
<output_buffer exist="on" circuit_model_name="INVTX1"/>
|
|
<pass_gate_logic circuit_model_name="TGATE"/>
|
|
<port type="input" prefix="in" size="1"/>
|
|
<port type="output" prefix="out" size="2"/>
|
|
<port type="bl" prefix="bl" size="1" default_val="0" inv_circuit_model_name="INVTX1"/>
|
|
<port type="blb" prefix="blb" size="1" default_val="1" inv_circuit_model_name="INVTX1"/>
|
|
<port type="wl" prefix="wl" size="1" default_val="0" inv_circuit_model_name="INVTX1"/>
|
|
</circuit_model>
|
|
<!--Scan-chain DFF subckt ports should be defined as <D> <Q> <Qb> <CLK> <RESET> <SET> -->
|
|
<circuit_model type="sff" name="sc_dff" prefix="scff" spice_netlist="OPENFPGAPATH/vpr7_x2p/vpr/SpiceNetlists/ff.sp" verilog_netlist="OPENFPGAPATH/vpr7_x2p/vpr/VerilogNetlists/ff.v">
|
|
<design_technology type="cmos"/>
|
|
<input_buffer exist="on" circuit_model_name="INVTX1"/>
|
|
<output_buffer exist="on" circuit_model_name="INVTX1"/>
|
|
<pass_gate_logic circuit_model_name="TGATE"/>
|
|
<port type="input" prefix="D" size="1"/>
|
|
<port type="input" prefix="pset" size="1" is_global="true" default_val="0" is_set="true" is_prog="true"/>
|
|
<port type="input" prefix="preset" size="1" is_global="true" default_val="0" is_reset="true" is_prog="true"/>
|
|
<port type="output" prefix="Q" size="2"/>
|
|
<port type="clock" prefix="prog_clk" size="1" is_global="true" default_val="0" is_prog="true" is_prog="true"/>
|
|
</circuit_model>
|
|
<circuit_model type="iopad" name="iopad" prefix="iopad" spice_netlist="OPENFPGAPATH/vpr7_x2p/vpr/SpiceNetlists/io.sp" verilog_netlist="OPENFPGAPATH/vpr7_x2p/vpr/VerilogNetlists/io.v">
|
|
<design_technology type="cmos"/>
|
|
<input_buffer exist="on" circuit_model_name="INVTX1"/>
|
|
<output_buffer exist="on" circuit_model_name="INVTX1"/>
|
|
<pass_gate_logic circuit_model_name="TGATE"/>
|
|
<port type="inout" prefix="pad" size="1"/>
|
|
<port type="sram" prefix="en" size="1" mode_select="true" circuit_model_name="sram6T_blwl" default_val="1"/>
|
|
<port type="input" prefix="outpad" size="1"/>
|
|
<port type="input" prefix="zin" size="1" is_global="true" default_val="0" />
|
|
<port type="output" prefix="inpad" size="1"/>
|
|
</circuit_model>
|
|
</module_circuit_models>
|
|
</spice_settings>
|
|
<device>
|
|
<!-- VB & JL: Using Ian Kuon's transistor sizing and drive strength data for routing, at 40 nm. Ian used BPTM
|
|
models. We are modifying the delay values however, to include metal C and R, which allows more architecture
|
|
experimentation. We are also modifying the relative resistance of PMOS to be 1.8x that of NMOS
|
|
(vs. Ian's 3x) as 1.8x lines up with Jeff G's data from a 45 nm process (and is more typical of
|
|
45 nm in general). I'm upping the Rmin_nmos from Ian's just over 6k to nearly 9k, and dropping
|
|
RminW_pmos from 18k to 16k to hit this 1.8x ratio, while keeping the delays of buffers approximately
|
|
lined up with Stratix IV.
|
|
We are using Jeff G.'s capacitance data for 45 nm (in tech/ptm_45nm).
|
|
Jeff's tables list C in for transistors with widths in multiples of the minimum feature size (45 nm).
|
|
The minimum contactable transistor is 2.5 * 45 nm, so I need to multiply drive strength sizes in this file
|
|
by 2.5x when looking up in Jeff's tables.
|
|
The delay values are lined up with Stratix IV, which has an architecture similar to this
|
|
proposed FPGA, and which is also 40 nm
|
|
C_ipin_cblock: input capacitance of a track buffer, which VPR assumes is a single-stage
|
|
4x minimum drive strength buffer. -->
|
|
|
|
<sizing R_minW_nmos="8926" R_minW_pmos="16067" ipin_mux_trans_size="9"/>
|
|
<timing C_ipin_cblock="596e-18" T_ipin_cblock="77.93e-12"/>
|
|
|
|
<!-- The grid_logic_tile_area below will be used for all blocks that do not explicitly set their own (non-routing)
|
|
area; set to 0 since we explicitly set the area of all blocks currently in this architecture file.
|
|
-->
|
|
<area grid_logic_tile_area="0"/>
|
|
<!--sram area="6" organization="standalone" circuit_model_name="sram6T"-->
|
|
<!--sram area="6" organization="scan-chain" circuit_model_name="sc_dff"-->
|
|
<sram area="6">
|
|
<verilog organization="scan-chain" circuit_model_name="sc_dff"/>
|
|
<!--verilog organization="memory_bank" circuit_model_name="sram6T_blwl"/-->
|
|
<spice organization="standalone" circuit_model_name="sram6T" />
|
|
</sram>
|
|
<chan_width_distr>
|
|
<io width="1.000000"/>
|
|
<x distr="uniform" peak="1.000000"/>
|
|
<y distr="uniform" peak="1.000000"/>
|
|
</chan_width_distr>
|
|
<switch_block type="wilton" fs="3"/>
|
|
</device>
|
|
|
|
<cblocks>
|
|
<switch type="mux" name="cb_mux" R="0" Cin="596e-18" Cout="0" Tdel="77.93e-12" mux_trans_size="3" buf_size="63" circuit_model_name="mux_2level_tapbuf" structure="multi-level" num_level="2">
|
|
</switch>
|
|
</cblocks>
|
|
<switchlist>
|
|
<!-- VB: the mux_trans_size and buf_size data below is in minimum width transistor *areas*, assuming the purple
|
|
book area formula. This means the mux transistors are about 5x minimum drive strength.
|
|
We assume the first stage of the buffer is 3x min drive strength to be reasonable given the large
|
|
mux transistors, and this gives a reasonable stage ratio of a bit over 5x to the second stage. We assume
|
|
the n and p transistors in the first stage are equal-sized to lower the buffer trip point, since it's fed
|
|
by a pass transistor mux. We can then reverse engineer the buffer second stage to hit the specified
|
|
buf_size (really buffer area) - 16.2x minimum drive nmos and 1.8*16.2 = 29.2x minimum drive.
|
|
I then took the data from Jeff G.'s PTM modeling of 45 nm to get the Cin (gate of first stage) and Cout
|
|
(diff of second stage) listed below. Jeff's models are in tech/ptm_45nm, and are in min feature multiples.
|
|
The minimum contactable transistor is 2.5 * 45 nm, so I need to multiply the drive strength sizes above by
|
|
2.5x when looking up in Jeff's tables.
|
|
Finally, we choose a switch delay (58 ps) that leads to length 4 wires having a delay equal to that of SIV of 126 ps.
|
|
This also leads to the switch being 46% of the total wire delay, which is reasonable. -->
|
|
<switch type="mux" name="sb_mux_L4" R="105" Cin="596e-18" Cout="0e-15" Tdel="47.2e-12" mux_trans_size="3" buf_size="63" circuit_model_name="mux_1level_tapbuf" structure="multi-level" num_level="1">
|
|
</switch>
|
|
<switch type="mux" name="sb_mux_L2" R="115" Cin="596e-18" Cout="0e-15" Tdel="47.2e-12" mux_trans_size="3" buf_size="63" circuit_model_name="mux_1level_tapbuf" structure="multi-level" num_level="1">
|
|
</switch>
|
|
<switch type="mux" name="sb_mux_L1" R="128" Cin="596e-18" Cout="0e-15" Tdel="47.2e-12" mux_trans_size="3" buf_size="63" circuit_model_name="mux_1level_tapbuf" structure="multi-level" num_level="1">
|
|
</switch>
|
|
</switchlist>
|
|
<segmentlist>
|
|
<!--- VB & JL: using ITRS metal stack data, 96 nm half pitch wires, which are intermediate metal width/space.
|
|
With the 96 nm half pitch, such wires would take 60 um of height, vs. a 90 nm high (approximated as square) Stratix IV tile so this seems
|
|
reasonable. Using a tile length of 90 nm, corresponding to the length of a Stratix IV tile if it were square. -->
|
|
<segment freq="0.4" length="4" type="unidir" Rmetal="101" Cmetal="22.5e-15" circuit_model_name="chan_segment">
|
|
<mux name="sb_mux_L4"/>
|
|
<sb type="pattern">1 1 1 1 1</sb>
|
|
<cb type="pattern">1 1 1 1</cb>
|
|
</segment>
|
|
<segment freq="0.3" length="2" type="unidir" Rmetal="101" Cmetal="22.5e-15" circuit_model_name="chan_segment">
|
|
<mux name="sb_mux_L4"/>
|
|
<sb type="pattern">1 1 1</sb>
|
|
<cb type="pattern">1 1 </cb>
|
|
</segment>
|
|
<segment freq="0.3" length="1" type="unidir" Rmetal="101" Cmetal="22.5e-15" circuit_model_name="chan_segment">
|
|
<mux name="sb_mux_L4"/>
|
|
<sb type="pattern">1 1</sb>
|
|
<cb type="pattern">1</cb>
|
|
</segment>
|
|
</segmentlist>
|
|
<!--switch_segment_patterns>
|
|
<pattern type="unbuf_sb" seg_length="1" seg_type="unidir" pattern_length="2">
|
|
<unbuf_mux name="1"/>
|
|
<sb type ="pattern">0 1</sb>
|
|
</pattern>
|
|
</switch_segment_patterns-->
|
|
|
|
<complexblocklist>
|
|
|
|
<!-- Define I/O pads begin -->
|
|
<!-- Capacity is a unique property of I/Os, it is the maximum number of I/Os that can be placed at the same (X,Y) location on the FPGA -->
|
|
<!-- Not sure of the area of an I/O (varies widely), and it's not relevant to the design of the FPGA core, so we're setting it to 0. -->
|
|
<pb_type name="io" capacity="8" area="0" idle_mode_name="inpad" physical_mode_name="io_phy">
|
|
<input name="outpad" num_pins="1"/>
|
|
<output name="inpad" num_pins="1"/>
|
|
|
|
<!-- physical design description -->
|
|
<mode name="io_phy" disabled_in_packing="false">
|
|
<pb_type name="iopad" blif_model=".subckt io" num_pb="1" circuit_model_name="iopad">
|
|
<input name="outpad" num_pins="1"/>
|
|
<output name="inpad" num_pins="1"/>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="inpad" input="iopad.inpad" output="io.inpad">
|
|
<delay_constant max="0e-11" in_port="iopad.inpad" out_port="io.inpad"/>
|
|
</direct>
|
|
<direct name="outpad" input="io.outpad" output="iopad.outpad">
|
|
<delay_constant max="0e-11" in_port="io.outpad" out_port="iopad.outpad"/>
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
|
|
<!-- IOs can operate as either inputs or outputs.§
|
|
Delays below come from Ian Kuon. They are small, so they should be interpreted as
|
|
the delays to and from registers in the I/O (and generally I/Os are registered
|
|
today and that is when you timing analyze them.
|
|
-->
|
|
<mode name="inpad">
|
|
<pb_type name="inpad" blif_model=".input" num_pb="1" circuit_model_name="iopad" mode_bits="1">
|
|
<output name="inpad" num_pins="1"/>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="inpad" input="inpad.inpad" output="io.inpad">
|
|
<delay_constant max="0e-11" in_port="inpad.inpad" out_port="io.inpad"/>
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
<mode name="outpad">
|
|
<pb_type name="outpad" blif_model=".output" num_pb="1" circuit_model_name="iopad" mode_bits="0">
|
|
<input name="outpad" num_pins="1"/>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="outpad" input="io.outpad" output="outpad.outpad">
|
|
<delay_constant max="0e-11" in_port="io.outpad" out_port="outpad.outpad"/>
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
|
|
<!-- Every input pin is driven by 15% of the tracks in a channel, every output pin is driven by 10% of the tracks in a channel -->
|
|
<fc default_in_type="frac" default_in_val="0.15" default_out_type="frac" default_out_val="0.10"/>
|
|
|
|
<!-- IOs go on the periphery of the FPGA, for consistency,
|
|
make it physically equivalent on all sides so that only one definition of I/Os is needed.
|
|
If I do not make a physically equivalent definition, then I need to define 4 different I/Os, one for each side of the FPGA
|
|
-->
|
|
<pinlocations pattern="custom">
|
|
<loc side="left">io.outpad io.inpad</loc>
|
|
<loc side="top">io.outpad io.inpad</loc>
|
|
<loc side="right">io.outpad io.inpad</loc>
|
|
<loc side="bottom">io.outpad io.inpad</loc>
|
|
</pinlocations>
|
|
|
|
<!-- Place I/Os on the sides of the FPGA -->
|
|
<gridlocations>
|
|
<loc type="perimeter" priority="10"/>
|
|
</gridlocations>
|
|
|
|
<power method="ignore"/>
|
|
</pb_type>
|
|
<!-- Define I/O pads ends -->
|
|
|
|
<!-- Define general purpose logic block (CLB) begin -->
|
|
<!--- Area calculation: Total Stratix IV tile area is about 8100 um^2, and a minimum width transistor
|
|
area is 60 L^2 yields a tile area of 84375 MWTAs.
|
|
Routing at W=300 is 30481 MWTAs, leaving us with a total of 53000 MWTAs for logic block area
|
|
This means that only 37% of our area is in the general routing, and 63% is inside the logic
|
|
block. Note that the crossbar / local interconnect is considered part of the logic block
|
|
area in this analysis. That is a lower proportion of of routing area than most academics
|
|
assume, but note that the total routing area really includes the crossbar, which would push
|
|
routing area up significantly, we estimate into the ~70% range.
|
|
-->
|
|
<pb_type name="clb" area="53894" opin_to_cb="false">
|
|
<pin_equivalence_auto_detect input_ports ="off" output_ports="off"/>
|
|
<input name="I" num_pins="40" equivalent="true"/>
|
|
<output name="O" num_pins="10" equivalent="false"/>
|
|
<!--input name="I" num_pins="40" equivalent="true"/-->
|
|
<!--output name="O" num_pins="20" equivalent="false"/-->
|
|
<clock name="clk" num_pins="1"/>
|
|
|
|
<!-- Describe fracturable logic element.
|
|
Each fracturable logic element has a 6-LUT that can alternatively operate as two 5-LUTs with shared inputs.
|
|
The outputs of the fracturable logic element can be optionally registered
|
|
For spice modeling: in each primitive pb_type, user should define a circuit_model_name that linkes to the
|
|
defined spice models
|
|
-->
|
|
<pb_type name="fle" num_pb="10" idle_mode_name="n1_lut6" physical_mode_name="n1_lut6">
|
|
<input name="in" num_pins="6"/>
|
|
<output name="out" num_pins="1"/>
|
|
<clock name="clk" num_pins="1"/>
|
|
<!-- 6-LUT mode definition begin -->
|
|
<mode name="n1_lut6">
|
|
<!-- Define 6-LUT mode -->
|
|
<pb_type name="ble6" num_pb="1">
|
|
<input name="in" num_pins="6"/>
|
|
<output name="out" num_pins="1"/>
|
|
<clock name="clk" num_pins="1"/>
|
|
|
|
<!-- Define LUT -->
|
|
<pb_type name="lut6" blif_model=".names" num_pb="1" class="lut" circuit_model_name="lut6">
|
|
<input name="in" num_pins="6" port_class="lut_in"/>
|
|
<output name="out" num_pins="1" port_class="lut_out"/>
|
|
<!-- LUT timing using delay matrix -->
|
|
<!-- These are the physical delay inputs on a Stratix IV LUT but because VPR cannot do LUT rebalancing,
|
|
we instead take the average of these numbers to get more stable results
|
|
82e-12
|
|
173e-12
|
|
261e-12
|
|
263e-12
|
|
398e-12
|
|
397e-12
|
|
-->
|
|
<delay_matrix type="max" in_port="lut6.in" out_port="lut6.out">
|
|
127e-12
|
|
127e-12
|
|
127e-12
|
|
127e-12
|
|
127e-12
|
|
127e-12
|
|
</delay_matrix>
|
|
</pb_type>
|
|
|
|
<!-- Define flip-flop -->
|
|
<pb_type name="ff" blif_model=".latch" num_pb="1" class="flipflop" circuit_model_name="static_dff">
|
|
<input name="D" num_pins="1" port_class="D"/>
|
|
<output name="Q" num_pins="1" port_class="Q"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="29e-12" port="ff.D" clock="clk"/>
|
|
<T_clock_to_Q max="16e-12" port="ff.Q" clock="clk"/>
|
|
</pb_type>
|
|
|
|
<interconnect>
|
|
<direct name="direct1" input="ble6.in" output="lut6[0:0].in"/>
|
|
<direct name="direct2" input="lut6.out" output="ff.D">
|
|
<!-- Advanced user option that tells CAD tool to find LUT+FF pairs in netlist -->
|
|
<pack_pattern name="ble6" in_port="lut6.out" out_port="ff.D"/>
|
|
</direct>
|
|
<direct name="direct3" input="ble6.clk" output="ff.clk"/>
|
|
<mux name="mux1" input="ff.Q lut6.out" output="ble6.out" circuit_model_name="mux_1level_tapbuf">
|
|
<!-- LUT to output is faster than FF to output on a Stratix IV -->
|
|
<delay_constant max="42.06e-12" in_port="lut6.out" out_port="ble6.out" />
|
|
<delay_constant max="42.06e-12" in_port="ff.Q" out_port="ble6.out" />
|
|
</mux>
|
|
</interconnect>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="direct1" input="fle.in" output="ble6.in"/>
|
|
<direct name="direct2" input="ble6.out" output="fle.out[0:0]"/>
|
|
<direct name="direct3" input="fle.clk" output="ble6.clk"/>
|
|
</interconnect>
|
|
</mode>
|
|
<!-- 6-LUT mode definition end -->
|
|
</pb_type>
|
|
<interconnect>
|
|
<!-- We use a full crossbar to get logical equivalence at inputs of CLB
|
|
The delays below come from Stratix IV. the delay through a connection block
|
|
input mux + the crossbar in Stratix IV is 167 ps. We already have a 72 ps
|
|
delay on the connection block input mux (modeled by Ian Kuon), so the remaining
|
|
delay within the crossbar is 95 ps.
|
|
The delays of cluster feedbacks in Stratix IV is 100 ps, when driven by a LUT.
|
|
Since all our outputs LUT outputs go to a BLE output, and have a delay of
|
|
25 ps to do so, we subtract 25 ps from the 100 ps delay of a feedback
|
|
to get the part that should be marked on the crossbar. -->
|
|
<complete name="crossbar" input="clb.I fle[9:0].out" output="fle[9:0].in" circuit_model_name="mux_2level">
|
|
<delay_constant max="53.44e-12" in_port="clb.I" out_port="fle[9:0].in" />
|
|
<delay_constant max="53.44e-12" in_port="fle[9:0].out" out_port="fle[9:0].in" />
|
|
</complete>
|
|
<complete name="clks" input="clb.clk" output="fle[9:0].clk">
|
|
</complete>
|
|
|
|
<!-- This way of specifying direct connection to clb outputs is important because this architecture uses automatic spreading of opins.
|
|
By grouping to output pins in this fashion, if a logic block is completely filled by 6-LUTs,
|
|
then the outputs those 6-LUTs take get evenly distributed across all four sides of the CLB instead of clumped on two sides (which is what happens with a more
|
|
naive specification).
|
|
-->
|
|
<direct name="clbouts1" input="fle[9:0].out[0:0]" output="clb.O[9:0]"/>
|
|
<!--direct name="clbouts2" input="fle[9:0].out[1:1]" output="clb.O[19:10]"/-->
|
|
</interconnect>
|
|
|
|
<!-- Every input pin is driven by 15% of the tracks in a channel, every output pin is driven by 10% of the tracks in a channel -->
|
|
<fc default_in_type="frac" default_in_val="0.15" default_out_type="frac" default_out_val="0.10"/>
|
|
|
|
<!--pinlocations pattern="spread"/-->
|
|
<pinlocations pattern="custom">
|
|
<loc side="top">clb.clk </loc>
|
|
<loc side="right">clb.I[19:0] clb.O[4:0] </loc>
|
|
<loc side="bottom">clb.I[39:20] clb.O[9:5] </loc>
|
|
</pinlocations>
|
|
|
|
<!-- Place this general purpose logic block in any unspecified column -->
|
|
<gridlocations>
|
|
<loc type="fill" priority="1"/>
|
|
</gridlocations>
|
|
</pb_type>
|
|
<!-- Define general purpose logic block (CLB) ends -->
|
|
|
|
<!-- Define fracturable multiplier begin -->
|
|
<!-- This multiplier can operate as a 36x36 multiplier that can fracture to two 18x18 multipliers each of which can further fracture to two 9x9 multipliers
|
|
For delay modelling, the 36x36 DSP multiplier in Stratix IV has a delay of 1.523 ns + 1.93 ns
|
|
= 3.45 ns. The 18x18 mode doesn't need to sum four 18x18 multipliers, so it is a bit
|
|
faster: 1.523 ns for the multiplier, and 1.09 ns for the multiplier output block.
|
|
For the input and output interconnect delays, unlike Stratix IV, we don't
|
|
have any routing/logic flexibility (crossbars) at the inputs. There is some output muxing
|
|
in Stratix IV and this architecture to select which multiplier outputs should go out (e.g.
|
|
9x9 outputs, 18x18 or 36x36) so those are very close between the two architectures.
|
|
We take the conservative (slightly pessimistic)
|
|
approach modelling the input as the same as the Stratix IV input delay and the output delay the same as the Stratix IV DSP out delay.
|
|
|
|
We estimate block area by using the published Stratix III data (which is architecturally identical to Stratix IV)
|
|
(H. Wong, V. Betz and J. Rose, "Comparing FPGA vs. Custom CMOS and the Impact on Processor Microarchitecture", FPGA 2011) of 0.2623
|
|
mm^2 and scaling from 65 to 40 nm to obtain 0.0993 mm^2. That area is for a DSP block with approximately 2x the functionality of
|
|
the block we use (can implement two 36x36 multiplies instead of our 1, eight 18x18 multiplies instead of our 4, etc.). Hence we
|
|
divide the area by 2 to obtain 0.0497 mm^2. One minimum-width transistor units = 60 L^2 (where L = 40 nm), so is 518,000 MWTUS.
|
|
That area includes routing and the connection block input muxes. Our DSP block is four
|
|
rows high, and hence includes four horizontal routing channel segments and four vertical ones, which is 4x the routing of a logic
|
|
block (single tile). It also includes 3.6x the outputs of a logic block, and 1.8x the inputs. Hence a slight overestimate of the routing
|
|
area associated with our DSP block is four times that of a logic tile, where the routing area of a logic tile was calculated above (at W = 300)
|
|
as 30481 MWTAs. Hence the (core, non-routing) area our DSP block is approximately 518,000 - 4 * 30,481 = 396,000 MWTUs.
|
|
-->
|
|
<!--pb_type name="mult_36" height="4" area="396000">
|
|
|
|
<input name="a" num_pins="36"/>
|
|
<input name="b" num_pins="36"/>
|
|
<output name="out" num_pins="72"/>
|
|
|
|
<mode name="two_divisible_mult_18x18">
|
|
<pb_type name="divisible_mult_18x18" num_pb="2">
|
|
<input name="a" num_pins="18"/>
|
|
<input name="b" num_pins="18"/>
|
|
<output name="out" num_pins="36"/-->
|
|
|
|
<!-- Model 9x9 delay and 18x18 delay as the same. 9x9 could be faster, but in Stratix IV
|
|
isn't, presumably because the multiplier layout is really optimized for 18x18.
|
|
-->
|
|
<!--mode name="two_mult_9x9">
|
|
<pb_type name="mult_9x9_slice" num_pb="2">
|
|
<input name="A_cfg" num_pins="9"/>
|
|
<input name="B_cfg" num_pins="9"/>
|
|
<output name="OUT_cfg" num_pins="18"/>
|
|
|
|
<pb_type name="mult_9x9" blif_model=".subckt multiply" num_pb="1">
|
|
<input name="a" num_pins="9"/>
|
|
<input name="b" num_pins="9"/>
|
|
<output name="out" num_pins="18"/>
|
|
<delay_constant max="1.523e-9" in_port="mult_9x9.a" out_port="mult_9x9.out"/>
|
|
<delay_constant max="1.523e-9" in_port="mult_9x9.b" out_port="mult_9x9.out"/>
|
|
</pb_type>
|
|
|
|
<interconnect>
|
|
<direct name="a2a" input="mult_9x9_slice.A_cfg" output="mult_9x9.a">
|
|
</direct>
|
|
<direct name="b2b" input="mult_9x9_slice.B_cfg" output="mult_9x9.b">
|
|
</direct>
|
|
<direct name="out2out" input="mult_9x9.out" output="mult_9x9_slice.OUT_cfg">
|
|
</direct>
|
|
</interconnect>
|
|
<power method="pin-toggle">
|
|
<port name="A_cfg" energy_per_toggle="1.45e-12"/>
|
|
<port name="B_cfg" energy_per_toggle="1.45e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="a2a" input="divisible_mult_18x18.a" output="mult_9x9_slice[1:0].A_cfg">
|
|
</direct>
|
|
<direct name="b2b" input="divisible_mult_18x18.b" output="mult_9x9_slice[1:0].B_cfg">
|
|
</direct>
|
|
<direct name="out2out" input="mult_9x9_slice[1:0].OUT_cfg" output="divisible_mult_18x18.out">
|
|
</direct>
|
|
</interconnect>
|
|
|
|
</mode>
|
|
|
|
<mode name="mult_18x18">
|
|
<pb_type name="mult_18x18_slice" num_pb="1">
|
|
<input name="A_cfg" num_pins="18"/>
|
|
<input name="B_cfg" num_pins="18"/>
|
|
<output name="OUT_cfg" num_pins="36"/>
|
|
|
|
<pb_type name="mult_18x18" blif_model=".subckt multiply" num_pb="1" >
|
|
<input name="a" num_pins="18"/>
|
|
<input name="b" num_pins="18"/>
|
|
<output name="out" num_pins="36"/>
|
|
<delay_constant max="1.523e-9" in_port="mult_18x18.a" out_port="mult_18x18.out"/>
|
|
<delay_constant max="1.523e-9" in_port="mult_18x18.b" out_port="mult_18x18.out"/>
|
|
</pb_type>
|
|
|
|
<interconnect>
|
|
<direct name="a2a" input="mult_18x18_slice.A_cfg" output="mult_18x18.a">
|
|
</direct>
|
|
<direct name="b2b" input="mult_18x18_slice.B_cfg" output="mult_18x18.b">
|
|
</direct>
|
|
<direct name="out2out" input="mult_18x18.out" output="mult_18x18_slice.OUT_cfg">
|
|
</direct>
|
|
</interconnect>
|
|
<power method="pin-toggle">
|
|
<port name="A_cfg" energy_per_toggle="1.09e-12"/>
|
|
<port name="B_cfg" energy_per_toggle="1.09e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="a2a" input="divisible_mult_18x18.a" output="mult_18x18_slice.A_cfg">
|
|
</direct>
|
|
<direct name="b2b" input="divisible_mult_18x18.b" output="mult_18x18_slice.B_cfg">
|
|
</direct>
|
|
<direct name="out2out" input="mult_18x18_slice.OUT_cfg" output="divisible_mult_18x18.out">
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
|
|
<power method="sum-of-children"/>
|
|
</pb_type>
|
|
<interconnect-->
|
|
<!-- Stratix IV input delay of 207ps is conservative for this architecture because this architecture does not have an input crossbar in the multiplier.
|
|
Subtract 72.5 ps delay, which is already in the connection block input mux, leading
|
|
-->
|
|
<!--direct name="a2a" input="mult_36.a" output="divisible_mult_18x18[1:0].a">
|
|
<delay_constant max="134e-12" in_port="mult_36.a" out_port="divisible_mult_18x18[1:0].a"/>
|
|
</direct>
|
|
<direct name="b2b" input="mult_36.b" output="divisible_mult_18x18[1:0].b">
|
|
<delay_constant max="134e-12" in_port="mult_36.b" out_port="divisible_mult_18x18[1:0].b"/>
|
|
</direct>
|
|
<direct name="out2out" input="divisible_mult_18x18[1:0].out" output="mult_36.out">
|
|
<delay_constant max="1.09e-9" in_port="divisible_mult_18x18[1:0].out" out_port="mult_36.out"/>
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
|
|
<mode name="mult_36x36">
|
|
<pb_type name="mult_36x36_slice" num_pb="1">
|
|
<input name="A_cfg" num_pins="36"/>
|
|
<input name="B_cfg" num_pins="36"/>
|
|
<output name="OUT_cfg" num_pins="72"/>
|
|
|
|
<pb_type name="mult_36x36" blif_model=".subckt multiply" num_pb="1">
|
|
<input name="a" num_pins="36"/>
|
|
<input name="b" num_pins="36"/>
|
|
<output name="out" num_pins="72"/>
|
|
<delay_constant max="1.523e-9" in_port="mult_36x36.a" out_port="mult_36x36.out"/>
|
|
<delay_constant max="1.523e-9" in_port="mult_36x36.b" out_port="mult_36x36.out"/>
|
|
</pb_type>
|
|
|
|
<interconnect>
|
|
<direct name="a2a" input="mult_36x36_slice.A_cfg" output="mult_36x36.a">
|
|
</direct>
|
|
<direct name="b2b" input="mult_36x36_slice.B_cfg" output="mult_36x36.b">
|
|
</direct>
|
|
<direct name="out2out" input="mult_36x36.out" output="mult_36x36_slice.OUT_cfg">
|
|
</direct>
|
|
</interconnect>
|
|
|
|
<power method="pin-toggle">
|
|
<port name="A_cfg" energy_per_toggle="2.13e-12"/>
|
|
<port name="B_cfg" energy_per_toggle="2.13e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect-->
|
|
<!-- Stratix IV input delay of 207ps is conservative for this architecture because this architecture does not have an input crossbar in the multiplier.
|
|
Subtract 72.5 ps delay, which is already in the connection block input mux, leading
|
|
to a 134 ps delay.
|
|
-->
|
|
<!--direct name="a2a" input="mult_36.a" output="mult_36x36_slice.A_cfg">
|
|
<delay_constant max="134e-12" in_port="mult_36.a" out_port="mult_36x36_slice.A_cfg"/>
|
|
</direct>
|
|
<direct name="b2b" input="mult_36.b" output="mult_36x36_slice.B_cfg">
|
|
<delay_constant max="134e-12" in_port="mult_36.b" out_port="mult_36x36_slice.B_cfg"/>
|
|
</direct>
|
|
<direct name="out2out" input="mult_36x36_slice.OUT_cfg" output="mult_36.out">
|
|
<delay_constant max="1.93e-9" in_port="mult_36x36_slice.OUT_cfg" out_port="mult_36.out"/>
|
|
</direct>
|
|
</interconnect>
|
|
|
|
</mode>
|
|
|
|
<fc default_in_type="frac" default_in_val="0.15" default_out_type="frac" default_out_val="0.10"/>
|
|
<pinlocations pattern="spread"/-->
|
|
|
|
<!-- Place this multiplier block every 8 columns from (and including) the sixth column -->
|
|
<!--gridlocations>
|
|
<loc type="col" start="6" repeat="8" priority="2"/>
|
|
</gridlocations>
|
|
<power method="sum-of-children"/>
|
|
</pb_type-->
|
|
<!-- Define fracturable multiplier end -->
|
|
|
|
<!-- Define fracturable memory begin -->
|
|
<!-- 32 Kb Memory that can operate from 512x64 to 32Kx1 for single-port mode and 1024x32 to 32Kx1 for dual-port mode.
|
|
Area and delay based off Stratix IV 9K and 144K memories (delay from linear interpolation, Tsu(483 ps, 636 ps) Tco(1084ps, 1969ps)).
|
|
Input delay = 204ps (from Stratix IV LAB line) - 72ps (this architecture does not lump connection box delay in internal delay)
|
|
Output delay = M4K buffer 50ps
|
|
|
|
Area is obtained by appropriately scaling and adjusting the published Stratix III (which is architecturally identical to Stratix IV)
|
|
data from H. Wong, V. Betz and J. Rose, "Comparing FPGA vs. Custom CMOS and the Impact on Processor Microarchitecture", FPGA 2011.
|
|
Linearly interpolating (by bit count) between the M9k and M144k areas to obtain an M32k (our RAM size) point yields a 65 nm area of
|
|
of 0.153 mm^2. Interpolating based on port count between the RAMs would instead yield an area of 0.209 mm^2 for our 32 kB RAM; since
|
|
bit count accounts for more area than ports for a RAM this size we choose the bit count interpolation; however, since the port interpolation
|
|
is not radically different this also gives us confidence that interpolating based on bits is OK, but slightly underpredicts area.
|
|
Scaling to 40 nm^2 yields .0579 mm^2, and converting to MWTUs at 60 L^2 / MWTU yields 604,000 MWTUs. This includes routing. A Stratix IV
|
|
M9K RAM is one row high and hence has one routing tile (one horizonal and one vertical routing segment area). An M144k RAM has 8 such tiles.
|
|
Linearly interpolating on
|
|
bits to 32 kb yields 2.2 routing tiles incorporated in the area number above. The inter-block routing represents 30% of the area of a logic
|
|
tile according to D. Lewis et al, "Architectural Enhancements in Stratix V," FPGA 2013. Hence we should subtract 0.3 * 2.2 * 84,375 MWTUs to
|
|
obtain a RAM core area (not including inter-block routing) of 548,000 MWTU areas for our 32 kb RAM in a 40 nm process.
|
|
-->
|
|
<!--pb_type name="memory" height="6" area="548000">
|
|
|
|
<input name="addr1" num_pins="15"/>
|
|
<input name="addr2" num_pins="15"/>
|
|
<input name="data" num_pins="64"/>
|
|
<input name="we1" num_pins="1"/>
|
|
<input name="we2" num_pins="1"/>
|
|
<output name="out" num_pins="64"/>
|
|
<clock name="clk" num_pins="1"/-->
|
|
|
|
<!-- Specify single port mode first -->
|
|
<!--mode name="mem_512x64_sp">
|
|
<pb_type name="mem_512x64_sp" blif_model=".subckt single_port_ram" class="memory" num_pb="1">
|
|
<input name="addr" num_pins="9" port_class="address"/>
|
|
<input name="data" num_pins="64" port_class="data_in"/>
|
|
<input name="we" num_pins="1" port_class="write_en"/>
|
|
<output name="out" num_pins="64" port_class="data_out"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="509e-12" port="mem_512x64_sp.addr" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_512x64_sp.data" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_512x64_sp.we" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_512x64_sp.out" clock="clk"/>
|
|
<power method="pin-toggle">
|
|
<port name="clk" energy_per_toggle="9.0e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="address1" input="memory.addr1[8:0]" output="mem_512x64_sp.addr">
|
|
<delay_constant max="132e-12" in_port="memory.addr1[8:0]" out_port="mem_512x64_sp.addr"/>
|
|
</direct>
|
|
<direct name="data1" input="memory.data[63:0]" output="mem_512x64_sp.data">
|
|
<delay_constant max="132e-12" in_port="memory.data[63:0]" out_port="mem_512x64_sp.data"/>
|
|
</direct>
|
|
<direct name="writeen1" input="memory.we1" output="mem_512x64_sp.we">
|
|
<delay_constant max="132e-12" in_port="memory.we1" out_port="mem_512x64_sp.we"/>
|
|
</direct>
|
|
<direct name="dataout1" input="mem_512x64_sp.out" output="memory.out[63:0]">
|
|
<delay_constant max="40e-12" in_port="mem_512x64_sp.out" out_port="memory.out[63:0]"/>
|
|
</direct>
|
|
<direct name="clk" input="memory.clk" output="mem_512x64_sp.clk">
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
|
|
<mode name="mem_1024x32_sp">
|
|
<pb_type name="mem_1024x32_sp" blif_model=".subckt single_port_ram" class="memory" num_pb="1">
|
|
<input name="addr" num_pins="10" port_class="address"/>
|
|
<input name="data" num_pins="32" port_class="data_in"/>
|
|
<input name="we" num_pins="1" port_class="write_en"/>
|
|
<output name="out" num_pins="32" port_class="data_out"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="509e-12" port="mem_1024x32_sp.addr" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_1024x32_sp.data" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_1024x32_sp.we" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_1024x32_sp.out" clock="clk"/>
|
|
<power method="pin-toggle">
|
|
<port name="clk" energy_per_toggle="9.0e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="address1" input="memory.addr1[9:0]" output="mem_1024x32_sp.addr">
|
|
<delay_constant max="132e-12" in_port="memory.addr1[9:0]" out_port="mem_1024x32_sp.addr"/>
|
|
</direct>
|
|
<direct name="data1" input="memory.data[31:0]" output="mem_1024x32_sp.data">
|
|
<delay_constant max="132e-12" in_port="memory.data[31:0]" out_port="mem_1024x32_sp.data"/>
|
|
</direct>
|
|
<direct name="writeen1" input="memory.we1" output="mem_1024x32_sp.we">
|
|
<delay_constant max="132e-12" in_port="memory.we1" out_port="mem_1024x32_sp.we"/>
|
|
</direct>
|
|
<direct name="dataout1" input="mem_1024x32_sp.out" output="memory.out[31:0]">
|
|
<delay_constant max="40e-12" in_port="mem_1024x32_sp.out" out_port="memory.out[31:0]"/>
|
|
</direct>
|
|
<direct name="clk" input="memory.clk" output="mem_1024x32_sp.clk">
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
|
|
|
|
<mode name="mem_2048x16_sp">
|
|
<pb_type name="mem_2048x16_sp" blif_model=".subckt single_port_ram" class="memory" num_pb="1">
|
|
<input name="addr" num_pins="11" port_class="address"/>
|
|
<input name="data" num_pins="16" port_class="data_in"/>
|
|
<input name="we" num_pins="1" port_class="write_en"/>
|
|
<output name="out" num_pins="16" port_class="data_out"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="509e-12" port="mem_2048x16_sp.addr" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_2048x16_sp.data" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_2048x16_sp.we" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_2048x16_sp.out" clock="clk"/>
|
|
<power method="pin-toggle">
|
|
<port name="clk" energy_per_toggle="9.0e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="address1" input="memory.addr1[10:0]" output="mem_2048x16_sp.addr">
|
|
<delay_constant max="132e-12" in_port="memory.addr1[10:0]" out_port="mem_2048x16_sp.addr"/>
|
|
</direct>
|
|
<direct name="data1" input="memory.data[15:0]" output="mem_2048x16_sp.data">
|
|
<delay_constant max="132e-12" in_port="memory.data[15:0]" out_port="mem_2048x16_sp.data"/>
|
|
</direct>
|
|
<direct name="writeen1" input="memory.we1" output="mem_2048x16_sp.we">
|
|
<delay_constant max="132e-12" in_port="memory.we1" out_port="mem_2048x16_sp.we"/>
|
|
</direct>
|
|
<direct name="dataout1" input="mem_2048x16_sp.out" output="memory.out[15:0]">
|
|
<delay_constant max="40e-12" in_port="mem_2048x16_sp.out" out_port="memory.out[15:0]"/>
|
|
</direct>
|
|
<direct name="clk" input="memory.clk" output="mem_2048x16_sp.clk">
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
|
|
<mode name="mem_4096x8_sp">
|
|
<pb_type name="mem_4096x8_sp" blif_model=".subckt single_port_ram" class="memory" num_pb="1">
|
|
<input name="addr" num_pins="12" port_class="address"/>
|
|
<input name="data" num_pins="8" port_class="data_in"/>
|
|
<input name="we" num_pins="1" port_class="write_en"/>
|
|
<output name="out" num_pins="8" port_class="data_out"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="509e-12" port="mem_4096x8_sp.addr" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_4096x8_sp.data" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_4096x8_sp.we" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_4096x8_sp.out" clock="clk"/>
|
|
<power method="pin-toggle">
|
|
<port name="clk" energy_per_toggle="9.0e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="address1" input="memory.addr1[11:0]" output="mem_4096x8_sp.addr">
|
|
<delay_constant max="132e-12" in_port="memory.addr1[11:0]" out_port="mem_4096x8_sp.addr"/>
|
|
</direct>
|
|
<direct name="data1" input="memory.data[7:0]" output="mem_4096x8_sp.data">
|
|
<delay_constant max="132e-12" in_port="memory.data[7:0]" out_port="mem_4096x8_sp.data"/>
|
|
</direct>
|
|
<direct name="writeen1" input="memory.we1" output="mem_4096x8_sp.we">
|
|
<delay_constant max="132e-12" in_port="memory.we1" out_port="mem_4096x8_sp.we"/>
|
|
</direct>
|
|
<direct name="dataout1" input="mem_4096x8_sp.out" output="memory.out[7:0]">
|
|
<delay_constant max="40e-12" in_port="mem_4096x8_sp.out" out_port="memory.out[7:0]"/>
|
|
</direct>
|
|
<direct name="clk" input="memory.clk" output="mem_4096x8_sp.clk">
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
|
|
<mode name="mem_8192x4_sp">
|
|
<pb_type name="mem_8192x4_sp" blif_model=".subckt single_port_ram" class="memory" num_pb="1">
|
|
<input name="addr" num_pins="13" port_class="address"/>
|
|
<input name="data" num_pins="4" port_class="data_in"/>
|
|
<input name="we" num_pins="1" port_class="write_en"/>
|
|
<output name="out" num_pins="4" port_class="data_out"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="509e-12" port="mem_8192x4_sp.addr" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_8192x4_sp.data" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_8192x4_sp.we" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_8192x4_sp.out" clock="clk"/>
|
|
<power method="pin-toggle">
|
|
<port name="clk" energy_per_toggle="9.0e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="address1" input="memory.addr1[12:0]" output="mem_8192x4_sp.addr">
|
|
<delay_constant max="132e-12" in_port="memory.addr1[12:0]" out_port="mem_8192x4_sp.addr"/>
|
|
</direct>
|
|
<direct name="data1" input="memory.data[3:0]" output="mem_8192x4_sp.data">
|
|
<delay_constant max="132e-12" in_port="memory.data[3:0]" out_port="mem_8192x4_sp.data"/>
|
|
</direct>
|
|
<direct name="writeen1" input="memory.we1" output="mem_8192x4_sp.we">
|
|
<delay_constant max="132e-12" in_port="memory.we1" out_port="mem_8192x4_sp.we"/>
|
|
</direct>
|
|
<direct name="dataout1" input="mem_8192x4_sp.out" output="memory.out[3:0]">
|
|
<delay_constant max="40e-12" in_port="mem_8192x4_sp.out" out_port="memory.out[3:0]"/>
|
|
</direct>
|
|
<direct name="clk" input="memory.clk" output="mem_8192x4_sp.clk">
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
|
|
<mode name="mem_16384x2_sp">
|
|
<pb_type name="mem_16384x2_sp" blif_model=".subckt single_port_ram" class="memory" num_pb="1">
|
|
<input name="addr" num_pins="14" port_class="address"/>
|
|
<input name="data" num_pins="2" port_class="data_in"/>
|
|
<input name="we" num_pins="1" port_class="write_en"/>
|
|
<output name="out" num_pins="2" port_class="data_out"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="509e-12" port="mem_16384x2_sp.addr" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_16384x2_sp.data" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_16384x2_sp.we" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_16384x2_sp.out" clock="clk"/>
|
|
<power method="pin-toggle">
|
|
<port name="clk" energy_per_toggle="9.0e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="address1" input="memory.addr1[13:0]" output="mem_16384x2_sp.addr">
|
|
<delay_constant max="132e-12" in_port="memory.addr1[13:0]" out_port="mem_16384x2_sp.addr"/>
|
|
</direct>
|
|
<direct name="data1" input="memory.data[1:0]" output="mem_16384x2_sp.data">
|
|
<delay_constant max="132e-12" in_port="memory.data[1:0]" out_port="mem_16384x2_sp.data"/>
|
|
</direct>
|
|
<direct name="writeen1" input="memory.we1" output="mem_16384x2_sp.we">
|
|
<delay_constant max="132e-12" in_port="memory.we1" out_port="mem_16384x2_sp.we"/>
|
|
</direct>
|
|
<direct name="dataout1" input="mem_16384x2_sp.out" output="memory.out[1:0]">
|
|
<delay_constant max="40e-12" in_port="mem_16384x2_sp.out" out_port="memory.out[1:0]"/>
|
|
</direct>
|
|
<direct name="clk" input="memory.clk" output="mem_16384x2_sp.clk">
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
|
|
<mode name="mem_32768x1_sp">
|
|
<pb_type name="mem_32768x1_sp" blif_model=".subckt single_port_ram" class="memory" num_pb="1">
|
|
<input name="addr" num_pins="15" port_class="address"/>
|
|
<input name="data" num_pins="1" port_class="data_in"/>
|
|
<input name="we" num_pins="1" port_class="write_en"/>
|
|
<output name="out" num_pins="1" port_class="data_out"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="509e-12" port="mem_32768x1_sp.addr" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_32768x1_sp.data" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_32768x1_sp.we" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_32768x1_sp.out" clock="clk"/>
|
|
<power method="pin-toggle">
|
|
<port name="clk" energy_per_toggle="9.0e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="address1" input="memory.addr1[14:0]" output="mem_32768x1_sp.addr">
|
|
<delay_constant max="132e-12" in_port="memory.addr1[14:0]" out_port="mem_32768x1_sp.addr"/>
|
|
</direct>
|
|
<direct name="data1" input="memory.data[0:0]" output="mem_32768x1_sp.data">
|
|
<delay_constant max="132e-12" in_port="memory.data[0:0]" out_port="mem_32768x1_sp.data"/>
|
|
</direct>
|
|
<direct name="writeen1" input="memory.we1" output="mem_32768x1_sp.we">
|
|
<delay_constant max="132e-12" in_port="memory.we1" out_port="mem_32768x1_sp.we"/>
|
|
</direct>
|
|
<direct name="dataout1" input="mem_32768x1_sp.out" output="memory.out[0:0]">
|
|
<delay_constant max="40e-12" in_port="mem_32768x1_sp.out" out_port="memory.out[0:0]"/>
|
|
</direct>
|
|
<direct name="clk" input="memory.clk" output="mem_32768x1_sp.clk">
|
|
</direct>
|
|
</interconnect>
|
|
</mode-->
|
|
|
|
<!-- Specify true dual port mode next -->
|
|
<!--mode name="mem_1024x32_dp">
|
|
<pb_type name="mem_1024x32_dp" blif_model=".subckt dual_port_ram" class="memory" num_pb="1">
|
|
<input name="addr1" num_pins="10" port_class="address1"/>
|
|
<input name="addr2" num_pins="10" port_class="address2"/>
|
|
<input name="data1" num_pins="32" port_class="data_in1"/>
|
|
<input name="data2" num_pins="32" port_class="data_in2"/>
|
|
<input name="we1" num_pins="1" port_class="write_en1"/>
|
|
<input name="we2" num_pins="1" port_class="write_en2"/>
|
|
<output name="out1" num_pins="32" port_class="data_out1"/>
|
|
<output name="out2" num_pins="32" port_class="data_out2"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="509e-12" port="mem_1024x32_dp.addr1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_1024x32_dp.data1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_1024x32_dp.we1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_1024x32_dp.addr2" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_1024x32_dp.data2" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_1024x32_dp.we2" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_1024x32_dp.out1" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_1024x32_dp.out2" clock="clk"/>
|
|
<power method="pin-toggle">
|
|
<port name="clk" energy_per_toggle="17.9e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="address1" input="memory.addr1[9:0]" output="mem_1024x32_dp.addr1">
|
|
<delay_constant max="132e-12" in_port="memory.addr1[9:0]" out_port="mem_1024x32_dp.addr1"/>
|
|
</direct>
|
|
<direct name="address2" input="memory.addr2[9:0]" output="mem_1024x32_dp.addr2">
|
|
<delay_constant max="132e-12" in_port="memory.addr2[9:0]" out_port="mem_1024x32_dp.addr2"/>
|
|
</direct>
|
|
<direct name="data1" input="memory.data[31:0]" output="mem_1024x32_dp.data1">
|
|
<delay_constant max="132e-12" in_port="memory.data[31:0]" out_port="mem_1024x32_dp.data1"/>
|
|
</direct>
|
|
<direct name="data2" input="memory.data[63:32]" output="mem_1024x32_dp.data2">
|
|
<delay_constant max="132e-12" in_port="memory.data[63:32]" out_port="mem_1024x32_dp.data2"/>
|
|
</direct>
|
|
<direct name="writeen1" input="memory.we1" output="mem_1024x32_dp.we1">
|
|
<delay_constant max="132e-12" in_port="memory.we1" out_port="mem_1024x32_dp.we1"/>
|
|
</direct>
|
|
<direct name="writeen2" input="memory.we2" output="mem_1024x32_dp.we2">
|
|
<delay_constant max="132e-12" in_port="memory.we2" out_port="mem_1024x32_dp.we2"/>
|
|
</direct>
|
|
<direct name="dataout1" input="mem_1024x32_dp.out1" output="memory.out[31:0]">
|
|
<delay_constant max="40e-12" in_port="mem_1024x32_dp.out1" out_port="memory.out[31:0]"/>
|
|
</direct>
|
|
<direct name="dataout2" input="mem_1024x32_dp.out2" output="memory.out[63:32]">
|
|
<delay_constant max="40e-12" in_port="mem_1024x32_dp.out2" out_port="memory.out[63:32]"/>
|
|
</direct>
|
|
<direct name="clk" input="memory.clk" output="mem_1024x32_dp.clk">
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
|
|
<mode name="mem_2048x16_dp">
|
|
<pb_type name="mem_2048x16_dp" blif_model=".subckt dual_port_ram" class="memory" num_pb="1">
|
|
<input name="addr1" num_pins="11" port_class="address1"/>
|
|
<input name="addr2" num_pins="11" port_class="address2"/>
|
|
<input name="data1" num_pins="16" port_class="data_in1"/>
|
|
<input name="data2" num_pins="16" port_class="data_in2"/>
|
|
<input name="we1" num_pins="1" port_class="write_en1"/>
|
|
<input name="we2" num_pins="1" port_class="write_en2"/>
|
|
<output name="out1" num_pins="16" port_class="data_out1"/>
|
|
<output name="out2" num_pins="16" port_class="data_out2"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="509e-12" port="mem_2048x16_dp.addr1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_2048x16_dp.data1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_2048x16_dp.we1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_2048x16_dp.addr2" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_2048x16_dp.data2" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_2048x16_dp.we2" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_2048x16_dp.out1" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_2048x16_dp.out2" clock="clk"/>
|
|
<power method="pin-toggle">
|
|
<port name="clk" energy_per_toggle="17.9e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="address1" input="memory.addr1[10:0]" output="mem_2048x16_dp.addr1">
|
|
<delay_constant max="132e-12" in_port="memory.addr1[10:0]" out_port="mem_2048x16_dp.addr1"/>
|
|
</direct>
|
|
<direct name="address2" input="memory.addr2[10:0]" output="mem_2048x16_dp.addr2">
|
|
<delay_constant max="132e-12" in_port="memory.addr2[10:0]" out_port="mem_2048x16_dp.addr2"/>
|
|
</direct>
|
|
<direct name="data1" input="memory.data[15:0]" output="mem_2048x16_dp.data1">
|
|
<delay_constant max="132e-12" in_port="memory.data[15:0]" out_port="mem_2048x16_dp.data1"/>
|
|
</direct>
|
|
<direct name="data2" input="memory.data[31:16]" output="mem_2048x16_dp.data2">
|
|
<delay_constant max="132e-12" in_port="memory.data[31:16]" out_port="mem_2048x16_dp.data2"/>
|
|
</direct>
|
|
<direct name="writeen1" input="memory.we1" output="mem_2048x16_dp.we1">
|
|
<delay_constant max="132e-12" in_port="memory.we1" out_port="mem_2048x16_dp.we1"/>
|
|
</direct>
|
|
<direct name="writeen2" input="memory.we2" output="mem_2048x16_dp.we2">
|
|
<delay_constant max="132e-12" in_port="memory.we2" out_port="mem_2048x16_dp.we2"/>
|
|
</direct>
|
|
<direct name="dataout1" input="mem_2048x16_dp.out1" output="memory.out[15:0]">
|
|
<delay_constant max="40e-12" in_port="mem_2048x16_dp.out1" out_port="memory.out[15:0]"/>
|
|
</direct>
|
|
<direct name="dataout2" input="mem_2048x16_dp.out2" output="memory.out[31:16]">
|
|
<delay_constant max="40e-12" in_port="mem_2048x16_dp.out2" out_port="memory.out[31:16]"/>
|
|
</direct>
|
|
<direct name="clk" input="memory.clk" output="mem_2048x16_dp.clk">
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
|
|
<mode name="mem_2048x8_dp">
|
|
<pb_type name="mem_2048x8_dp" blif_model=".subckt dual_port_ram" class="memory" num_pb="1">
|
|
<input name="addr1" num_pins="12" port_class="address1"/>
|
|
<input name="addr2" num_pins="12" port_class="address2"/>
|
|
<input name="data1" num_pins="8" port_class="data_in1"/>
|
|
<input name="data2" num_pins="8" port_class="data_in2"/>
|
|
<input name="we1" num_pins="1" port_class="write_en1"/>
|
|
<input name="we2" num_pins="1" port_class="write_en2"/>
|
|
<output name="out1" num_pins="8" port_class="data_out1"/>
|
|
<output name="out2" num_pins="8" port_class="data_out2"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="509e-12" port="mem_2048x8_dp.addr1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_2048x8_dp.data1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_2048x8_dp.we1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_2048x8_dp.addr2" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_2048x8_dp.data2" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_2048x8_dp.we2" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_2048x8_dp.out1" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_2048x8_dp.out2" clock="clk"/>
|
|
<power method="pin-toggle">
|
|
<port name="clk" energy_per_toggle="17.9e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="address1" input="memory.addr1[11:0]" output="mem_2048x8_dp.addr1">
|
|
<delay_constant max="132e-12" in_port="memory.addr1[11:0]" out_port="mem_2048x8_dp.addr1"/>
|
|
</direct>
|
|
<direct name="address2" input="memory.addr2[11:0]" output="mem_2048x8_dp.addr2">
|
|
<delay_constant max="132e-12" in_port="memory.addr2[11:0]" out_port="mem_2048x8_dp.addr2"/>
|
|
</direct>
|
|
<direct name="data1" input="memory.data[7:0]" output="mem_2048x8_dp.data1">
|
|
<delay_constant max="132e-12" in_port="memory.data[7:0]" out_port="mem_2048x8_dp.data1"/>
|
|
</direct>
|
|
<direct name="data2" input="memory.data[15:8]" output="mem_2048x8_dp.data2">
|
|
<delay_constant max="132e-12" in_port="memory.data[15:8]" out_port="mem_2048x8_dp.data2"/>
|
|
</direct>
|
|
<direct name="writeen1" input="memory.we1" output="mem_2048x8_dp.we1">
|
|
<delay_constant max="132e-12" in_port="memory.we1" out_port="mem_2048x8_dp.we1"/>
|
|
</direct>
|
|
<direct name="writeen2" input="memory.we2" output="mem_2048x8_dp.we2">
|
|
<delay_constant max="132e-12" in_port="memory.we2" out_port="mem_2048x8_dp.we2"/>
|
|
</direct>
|
|
<direct name="dataout1" input="mem_2048x8_dp.out1" output="memory.out[7:0]">
|
|
<delay_constant max="40e-12" in_port="mem_2048x8_dp.out1" out_port="memory.out[7:0]"/>
|
|
</direct>
|
|
<direct name="dataout2" input="mem_2048x8_dp.out2" output="memory.out[15:8]">
|
|
<delay_constant max="40e-12" in_port="mem_2048x8_dp.out2" out_port="memory.out[15:8]"/>
|
|
</direct>
|
|
<direct name="clk" input="memory.clk" output="mem_2048x8_dp.clk">
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
<mode name="mem_8192x4_dp">
|
|
<pb_type name="mem_8192x4_dp" blif_model=".subckt dual_port_ram" class="memory" num_pb="1">
|
|
<input name="addr1" num_pins="13" port_class="address1"/>
|
|
<input name="addr2" num_pins="13" port_class="address2"/>
|
|
<input name="data1" num_pins="4" port_class="data_in1"/>
|
|
<input name="data2" num_pins="4" port_class="data_in2"/>
|
|
<input name="we1" num_pins="1" port_class="write_en1"/>
|
|
<input name="we2" num_pins="1" port_class="write_en2"/>
|
|
<output name="out1" num_pins="4" port_class="data_out1"/>
|
|
<output name="out2" num_pins="4" port_class="data_out2"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="509e-12" port="mem_8192x4_dp.addr1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_8192x4_dp.data1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_8192x4_dp.we1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_8192x4_dp.addr2" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_8192x4_dp.data2" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_8192x4_dp.we2" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_8192x4_dp.out1" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_8192x4_dp.out2" clock="clk"/>
|
|
<power method="pin-toggle">
|
|
<port name="clk" energy_per_toggle="17.9e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="address1" input="memory.addr1[12:0]" output="mem_8192x4_dp.addr1">
|
|
<delay_constant max="132e-12" in_port="memory.addr1[12:0]" out_port="mem_8192x4_dp.addr1"/>
|
|
</direct>
|
|
<direct name="address2" input="memory.addr2[12:0]" output="mem_8192x4_dp.addr2">
|
|
<delay_constant max="132e-12" in_port="memory.addr2[12:0]" out_port="mem_8192x4_dp.addr2"/>
|
|
</direct>
|
|
<direct name="data1" input="memory.data[3:0]" output="mem_8192x4_dp.data1">
|
|
<delay_constant max="132e-12" in_port="memory.data[3:0]" out_port="mem_8192x4_dp.data1"/>
|
|
</direct>
|
|
<direct name="data2" input="memory.data[7:4]" output="mem_8192x4_dp.data2">
|
|
<delay_constant max="132e-12" in_port="memory.data[7:4]" out_port="mem_8192x4_dp.data2"/>
|
|
</direct>
|
|
<direct name="writeen1" input="memory.we1" output="mem_8192x4_dp.we1">
|
|
<delay_constant max="132e-12" in_port="memory.we1" out_port="mem_8192x4_dp.we1"/>
|
|
</direct>
|
|
<direct name="writeen2" input="memory.we2" output="mem_8192x4_dp.we2">
|
|
<delay_constant max="132e-12" in_port="memory.we2" out_port="mem_8192x4_dp.we2"/>
|
|
</direct>
|
|
<direct name="dataout1" input="mem_8192x4_dp.out1" output="memory.out[3:0]">
|
|
<delay_constant max="40e-12" in_port="mem_8192x4_dp.out1" out_port="memory.out[3:0]"/>
|
|
</direct>
|
|
<direct name="dataout2" input="mem_8192x4_dp.out2" output="memory.out[7:4]">
|
|
<delay_constant max="40e-12" in_port="mem_8192x4_dp.out2" out_port="memory.out[7:4]"/>
|
|
</direct>
|
|
<direct name="clk" input="memory.clk" output="mem_8192x4_dp.clk">
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
<mode name="mem_16384x2_dp">
|
|
<pb_type name="mem_16384x2_dp" blif_model=".subckt dual_port_ram" class="memory" num_pb="1">
|
|
<input name="addr1" num_pins="14" port_class="address1"/>
|
|
<input name="addr2" num_pins="14" port_class="address2"/>
|
|
<input name="data1" num_pins="2" port_class="data_in1"/>
|
|
<input name="data2" num_pins="2" port_class="data_in2"/>
|
|
<input name="we1" num_pins="1" port_class="write_en1"/>
|
|
<input name="we2" num_pins="1" port_class="write_en2"/>
|
|
<output name="out1" num_pins="2" port_class="data_out1"/>
|
|
<output name="out2" num_pins="2" port_class="data_out2"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="509e-12" port="mem_16384x2_dp.addr1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_16384x2_dp.data1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_16384x2_dp.we1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_16384x2_dp.addr2" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_16384x2_dp.data2" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_16384x2_dp.we2" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_16384x2_dp.out1" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_16384x2_dp.out2" clock="clk"/>
|
|
<power method="pin-toggle">
|
|
<port name="clk" energy_per_toggle="17.9e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="address1" input="memory.addr1[13:0]" output="mem_16384x2_dp.addr1">
|
|
<delay_constant max="132e-12" in_port="memory.addr1[13:0]" out_port="mem_16384x2_dp.addr1"/>
|
|
</direct>
|
|
<direct name="address2" input="memory.addr2[13:0]" output="mem_16384x2_dp.addr2">
|
|
<delay_constant max="132e-12" in_port="memory.addr2[13:0]" out_port="mem_16384x2_dp.addr2"/>
|
|
</direct>
|
|
<direct name="data1" input="memory.data[1:0]" output="mem_16384x2_dp.data1">
|
|
<delay_constant max="132e-12" in_port="memory.data[1:0]" out_port="mem_16384x2_dp.data1"/>
|
|
</direct>
|
|
<direct name="data2" input="memory.data[3:2]" output="mem_16384x2_dp.data2">
|
|
<delay_constant max="132e-12" in_port="memory.data[3:2]" out_port="mem_16384x2_dp.data2"/>
|
|
</direct>
|
|
<direct name="writeen1" input="memory.we1" output="mem_16384x2_dp.we1">
|
|
<delay_constant max="132e-12" in_port="memory.we1" out_port="mem_16384x2_dp.we1"/>
|
|
</direct>
|
|
<direct name="writeen2" input="memory.we2" output="mem_16384x2_dp.we2">
|
|
<delay_constant max="132e-12" in_port="memory.we2" out_port="mem_16384x2_dp.we2"/>
|
|
</direct>
|
|
<direct name="dataout1" input="mem_16384x2_dp.out1" output="memory.out[1:0]">
|
|
<delay_constant max="40e-12" in_port="mem_16384x2_dp.out1" out_port="memory.out[1:0]"/>
|
|
</direct>
|
|
<direct name="dataout2" input="mem_16384x2_dp.out2" output="memory.out[3:2]">
|
|
<delay_constant max="40e-12" in_port="mem_16384x2_dp.out2" out_port="memory.out[3:2]"/>
|
|
</direct>
|
|
<direct name="clk" input="memory.clk" output="mem_16384x2_dp.clk">
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
|
|
<mode name="mem_32768x1_dp">
|
|
<pb_type name="mem_32768x1_dp" blif_model=".subckt dual_port_ram" class="memory" num_pb="1">
|
|
<input name="addr1" num_pins="15" port_class="address1"/>
|
|
<input name="addr2" num_pins="15" port_class="address2"/>
|
|
<input name="data1" num_pins="1" port_class="data_in1"/>
|
|
<input name="data2" num_pins="1" port_class="data_in2"/>
|
|
<input name="we1" num_pins="1" port_class="write_en1"/>
|
|
<input name="we2" num_pins="1" port_class="write_en2"/>
|
|
<output name="out1" num_pins="1" port_class="data_out1"/>
|
|
<output name="out2" num_pins="1" port_class="data_out2"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="509e-12" port="mem_32768x1_dp.addr1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_32768x1_dp.data1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_32768x1_dp.we1" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_32768x1_dp.addr2" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_32768x1_dp.data2" clock="clk"/>
|
|
<T_setup value="509e-12" port="mem_32768x1_dp.we2" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_32768x1_dp.out1" clock="clk"/>
|
|
<T_clock_to_Q max="1.234e-9" port="mem_32768x1_dp.out2" clock="clk"/>
|
|
<power method="pin-toggle">
|
|
<port name="clk" energy_per_toggle="17.9e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="address1" input="memory.addr1[14:0]" output="mem_32768x1_dp.addr1">
|
|
<delay_constant max="132e-12" in_port="memory.addr1[14:0]" out_port="mem_32768x1_dp.addr1"/>
|
|
</direct>
|
|
<direct name="address2" input="memory.addr2[14:0]" output="mem_32768x1_dp.addr2">
|
|
<delay_constant max="132e-12" in_port="memory.addr2[14:0]" out_port="mem_32768x1_dp.addr2"/>
|
|
</direct>
|
|
<direct name="data1" input="memory.data[0:0]" output="mem_32768x1_dp.data1">
|
|
<delay_constant max="132e-12" in_port="memory.data[0:0]" out_port="mem_32768x1_dp.data1"/>
|
|
</direct>
|
|
<direct name="data2" input="memory.data[1:1]" output="mem_32768x1_dp.data2">
|
|
<delay_constant max="132e-12" in_port="memory.data[1:1]" out_port="mem_32768x1_dp.data2"/>
|
|
</direct>
|
|
<direct name="writeen1" input="memory.we1" output="mem_32768x1_dp.we1">
|
|
<delay_constant max="132e-12" in_port="memory.we1" out_port="mem_32768x1_dp.we1"/>
|
|
</direct>
|
|
<direct name="writeen2" input="memory.we2" output="mem_32768x1_dp.we2">
|
|
<delay_constant max="132e-12" in_port="memory.we2" out_port="mem_32768x1_dp.we2"/>
|
|
</direct>
|
|
<direct name="dataout1" input="mem_32768x1_dp.out1" output="memory.out[0:0]">
|
|
<delay_constant max="40e-12" in_port="mem_32768x1_dp.out1" out_port="memory.out[0:0]"/>
|
|
</direct>
|
|
<direct name="dataout2" input="mem_32768x1_dp.out2" output="memory.out[1:1]">
|
|
<delay_constant max="40e-12" in_port="mem_32768x1_dp.out2" out_port="memory.out[1:1]"/>
|
|
</direct>
|
|
<direct name="clk" input="memory.clk" output="mem_32768x1_dp.clk">
|
|
</direct>
|
|
</interconnect>
|
|
</mode-->
|
|
|
|
<!-- Every input pin is driven by 15% of the tracks in a channel, every output pin is driven by 10% of the tracks in a channel -->
|
|
<!--fc default_in_type="frac" default_in_val="0.15" default_out_type="frac" default_out_val="0.10"/>
|
|
<pinlocations pattern="spread"/-->
|
|
|
|
<!-- Place this memory block every 8 columns from (and including) the second column -->
|
|
<!--gridlocations>
|
|
<loc type="col" start="2" repeat="8" priority="2"/>
|
|
</gridlocations>
|
|
|
|
<power method="sum-of-children"/>
|
|
</pb_type-->
|
|
<!-- Define fracturable memory end -->
|
|
|
|
|
|
</complexblocklist>
|
|
<power>
|
|
<local_interconnect C_wire="0"/>
|
|
<mux_transistor_size mux_transistor_size="5"/>
|
|
<FF_size FF_size="4"/>
|
|
<LUT_transistor_size LUT_transistor_size="5"/>
|
|
</power>
|
|
<clocks>
|
|
<clock buffer_size="auto" C_wire="0"/>
|
|
</clocks>
|
|
</architecture>
|