443 lines
24 KiB
XML
443 lines
24 KiB
XML
<!--
|
|
Architecture with no fracturable LUTs
|
|
|
|
- 40 nm technology
|
|
- General purpose logic block:
|
|
K = 4, N = 4
|
|
- Routing architecture: L = 4, fc_in = 0.15, Fc_out = 0.1
|
|
- DSP block
|
|
- 8-bit multiplier
|
|
- input and output registers
|
|
|
|
Details on Modelling:
|
|
|
|
Based on flagship k6_frac_N10_mem32K_40nm.xml architecture. This architecture has no fracturable LUTs nor any heterogeneous blocks.
|
|
|
|
|
|
Authors: Jason Luu, Jeff Goeders, Vaughn Betz
|
|
-->
|
|
<architecture>
|
|
<!--
|
|
ODIN II specific config begins
|
|
Describes the types of user-specified netlist blocks (in blif, this corresponds to
|
|
".model [type_of_block]") that this architecture supports.
|
|
|
|
Note: Basic LUTs, I/Os, and flip-flops are not included here as there are
|
|
already special structures in blif (.names, .input, .output, and .latch)
|
|
that describe them.
|
|
-->
|
|
<models>
|
|
<!-- A virtual model for I/O to be used in the physical mode of io block -->
|
|
<model name="io">
|
|
<input_ports>
|
|
<port name="outpad"/>
|
|
</input_ports>
|
|
<output_ports>
|
|
<port name="inpad"/>
|
|
</output_ports>
|
|
</model>
|
|
<model name="mult_8">
|
|
<input_ports>
|
|
<port name="A" combinational_sink_ports="Y"/>
|
|
<port name="B" combinational_sink_ports="Y"/>
|
|
</input_ports>
|
|
<output_ports>
|
|
<port name="Y"/>
|
|
</output_ports>
|
|
</model>
|
|
</models>
|
|
<tiles>
|
|
<tile name="io" capacity="8" area="0">
|
|
<equivalent_sites>
|
|
<site pb_type="io"/>
|
|
</equivalent_sites>
|
|
<input name="outpad" num_pins="1"/>
|
|
<output name="inpad" num_pins="1"/>
|
|
<fc in_type="frac" in_val="0.15" out_type="frac" out_val="0.10"/>
|
|
<pinlocations pattern="custom">
|
|
<loc side="left">io.outpad io.inpad</loc>
|
|
<loc side="top">io.outpad io.inpad</loc>
|
|
<loc side="right">io.outpad io.inpad</loc>
|
|
<loc side="bottom">io.outpad io.inpad</loc>
|
|
</pinlocations>
|
|
</tile>
|
|
<tile name="clb" area="53894">
|
|
<equivalent_sites>
|
|
<site pb_type="clb"/>
|
|
</equivalent_sites>
|
|
<input name="I" num_pins="10" equivalent="full"/>
|
|
<output name="O" num_pins="4" equivalent="none"/>
|
|
<clock name="clk" num_pins="1"/>
|
|
<fc in_type="frac" in_val="0.15" out_type="frac" out_val="0.10"/>
|
|
<pinlocations pattern="spread"/>
|
|
</tile>
|
|
<tile name="mult_8" height="2" area="396000">
|
|
<equivalent_sites>
|
|
<site pb_type="mult_8" pin_mapping="direct"/>
|
|
</equivalent_sites>
|
|
<input name="a" num_pins="8"/>
|
|
<input name="b" num_pins="8"/>
|
|
<output name="out" num_pins="16"/>
|
|
<clock name="clk" num_pins="1"/>
|
|
<fc in_type="frac" in_val="0.15" out_type="frac" out_val="0.10"/>
|
|
<!-- Highly recommand to customize pin location when direct connection is used!!! -->
|
|
<!-- pinlocations are designed to spread pin on 4 sides evenly -->
|
|
<pinlocations pattern="custom">
|
|
<loc side="left">mult_8.a[0:3] mult_8.b[0:3] mult_8.out[0:7]</loc>
|
|
<loc side="top">mult_8.clk</loc>
|
|
<loc side="right">mult_8.a[4:7] mult_8.b[4:7] mult_8.out[8:15]</loc>
|
|
<loc side="bottom"></loc>
|
|
</pinlocations>
|
|
</tile>
|
|
</tiles>
|
|
<!-- ODIN II specific config ends -->
|
|
<!-- Physical descriptions begin -->
|
|
<layout tileable="true">
|
|
<auto_layout aspect_ratio="1.0">
|
|
<!--Perimeter of 'io' blocks with 'EMPTY' blocks at corners-->
|
|
<perimeter type="io" priority="100"/>
|
|
<corners type="EMPTY" priority="101"/>
|
|
<!--Fill with 'clb'-->
|
|
<fill type="clb" priority="10"/>
|
|
</auto_layout>
|
|
<fixed_layout name="2x2" width="4" height="4">
|
|
<!--Perimeter of 'io' blocks with 'EMPTY' blocks at corners-->
|
|
<perimeter type="io" priority="100"/>
|
|
<corners type="EMPTY" priority="101"/>
|
|
<!--Fill with 'clb'-->
|
|
<fill type="clb" priority="10"/>
|
|
</fixed_layout>
|
|
<fixed_layout name="3x2" width="5" height="4">
|
|
<!--Perimeter of 'io' blocks with 'EMPTY' blocks at corners-->
|
|
<perimeter type="io" priority="100"/>
|
|
<corners type="EMPTY" priority="101"/>
|
|
<!--Fill with 'clb'-->
|
|
<fill type="clb" priority="10"/>
|
|
<!--Column of 'memory' with 'EMPTY' blocks wherever a 'memory' does not fit. Vertical offset by 1 for perimeter.-->
|
|
<col type="mult_8" startx="2" starty="1" repeatx="8" priority="20"/>
|
|
<col type="EMPTY" startx="2" repeatx="8" starty="1" priority="19"/>
|
|
</fixed_layout>
|
|
</layout>
|
|
<device>
|
|
<!-- VB & JL: Using Ian Kuon's transistor sizing and drive strength data for routing, at 40 nm. Ian used BPTM
|
|
models. We are modifying the delay values however, to include metal C and R, which allows more architecture
|
|
experimentation. We are also modifying the relative resistance of PMOS to be 1.8x that of NMOS
|
|
(vs. Ian's 3x) as 1.8x lines up with Jeff G's data from a 45 nm process (and is more typical of
|
|
45 nm in general). I'm upping the Rmin_nmos from Ian's just over 6k to nearly 9k, and dropping
|
|
RminW_pmos from 18k to 16k to hit this 1.8x ratio, while keeping the delays of buffers approximately
|
|
lined up with Stratix IV.
|
|
We are using Jeff G.'s capacitance data for 45 nm (in tech/ptm_45nm).
|
|
Jeff's tables list C in for transistors with widths in multiples of the minimum feature size (45 nm).
|
|
The minimum contactable transistor is 2.5 * 45 nm, so I need to multiply drive strength sizes in this file
|
|
by 2.5x when looking up in Jeff's tables.
|
|
The delay values are lined up with Stratix IV, which has an architecture similar to this
|
|
proposed FPGA, and which is also 40 nm
|
|
C_ipin_cblock: input capacitance of a track buffer, which VPR assumes is a single-stage
|
|
4x minimum drive strength buffer. -->
|
|
<sizing R_minW_nmos="8926" R_minW_pmos="16067"/>
|
|
<!-- The grid_logic_tile_area below will be used for all blocks that do not explicitly set their own (non-routing)
|
|
area; set to 0 since we explicitly set the area of all blocks currently in this architecture file.
|
|
-->
|
|
<area grid_logic_tile_area="0"/>
|
|
<chan_width_distr>
|
|
<x distr="uniform" peak="1.000000"/>
|
|
<y distr="uniform" peak="1.000000"/>
|
|
</chan_width_distr>
|
|
<switch_block type="wilton" fs="3"/>
|
|
<connection_block input_switch_name="ipin_cblock"/>
|
|
</device>
|
|
<switchlist>
|
|
<!-- VB: the mux_trans_size and buf_size data below is in minimum width transistor *areas*, assuming the purple
|
|
book area formula. This means the mux transistors are about 5x minimum drive strength.
|
|
We assume the first stage of the buffer is 3x min drive strength to be reasonable given the large
|
|
mux transistors, and this gives a reasonable stage ratio of a bit over 5x to the second stage. We assume
|
|
the n and p transistors in the first stage are equal-sized to lower the buffer trip point, since it's fed
|
|
by a pass transistor mux. We can then reverse engineer the buffer second stage to hit the specified
|
|
buf_size (really buffer area) - 16.2x minimum drive nmos and 1.8*16.2 = 29.2x minimum drive.
|
|
I then took the data from Jeff G.'s PTM modeling of 45 nm to get the Cin (gate of first stage) and Cout
|
|
(diff of second stage) listed below. Jeff's models are in tech/ptm_45nm, and are in min feature multiples.
|
|
The minimum contactable transistor is 2.5 * 45 nm, so I need to multiply the drive strength sizes above by
|
|
2.5x when looking up in Jeff's tables.
|
|
Finally, we choose a switch delay (58 ps) that leads to length 4 wires having a delay equal to that of SIV of 126 ps.
|
|
This also leads to the switch being 46% of the total wire delay, which is reasonable. -->
|
|
<switch type="mux" name="0" R="551" Cin=".77e-15" Cout="4e-15" Tdel="58e-12" mux_trans_size="2.630740" buf_size="27.645901"/>
|
|
<!--switch ipin_cblock resistance set to yeild for 4x minimum drive strength buffer-->
|
|
<switch type="mux" name="ipin_cblock" R="2231.5" Cout="0." Cin="1.47e-15" Tdel="7.247000e-11" mux_trans_size="1.222260" buf_size="auto"/>
|
|
</switchlist>
|
|
<segmentlist>
|
|
<!--- VB & JL: using ITRS metal stack data, 96 nm half pitch wires, which are intermediate metal width/space.
|
|
With the 96 nm half pitch, such wires would take 60 um of height, vs. a 90 nm high (approximated as square) Stratix IV tile so this seems
|
|
reasonable. Using a tile length of 90 nm, corresponding to the length of a Stratix IV tile if it were square. -->
|
|
<segment name="L4" freq="1.000000" length="4" type="unidir" Rmetal="101" Cmetal="22.5e-15">
|
|
<mux name="0"/>
|
|
<sb type="pattern">1 1 1 1 1</sb>
|
|
<cb type="pattern">1 1 1 1</cb>
|
|
</segment>
|
|
</segmentlist>
|
|
<complexblocklist>
|
|
<!-- Define I/O pads begin -->
|
|
<!-- Capacity is a unique property of I/Os, it is the maximum number of I/Os that can be placed at the same (X,Y) location on the FPGA -->
|
|
<!-- Not sure of the area of an I/O (varies widely), and it's not relevant to the design of the FPGA core, so we're setting it to 0. -->
|
|
<pb_type name="io">
|
|
<input name="outpad" num_pins="1"/>
|
|
<output name="inpad" num_pins="1"/>
|
|
<!-- A mode denotes the physical implementation of an I/O
|
|
This mode will be not packable but is mainly used for fabric verilog generation
|
|
-->
|
|
<mode name="physical" disable_packing="true">
|
|
<pb_type name="iopad" blif_model=".subckt io" num_pb="1">
|
|
<input name="outpad" num_pins="1"/>
|
|
<output name="inpad" num_pins="1"/>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="outpad" input="io.outpad" output="iopad.outpad">
|
|
<delay_constant max="1.394e-11" in_port="io.outpad" out_port="iopad.outpad"/>
|
|
</direct>
|
|
<direct name="inpad" input="iopad.inpad" output="io.inpad">
|
|
<delay_constant max="4.243e-11" in_port="iopad.inpad" out_port="io.inpad"/>
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
<!-- IOs can operate as either inputs or outputs.
|
|
Delays below come from Ian Kuon. They are small, so they should be interpreted as
|
|
the delays to and from registers in the I/O (and generally I/Os are registered
|
|
today and that is when you timing analyze them.
|
|
-->
|
|
<mode name="inpad">
|
|
<pb_type name="inpad" blif_model=".input" num_pb="1">
|
|
<output name="inpad" num_pins="1"/>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="inpad" input="inpad.inpad" output="io.inpad">
|
|
<delay_constant max="4.243e-11" in_port="inpad.inpad" out_port="io.inpad"/>
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
<mode name="outpad">
|
|
<pb_type name="outpad" blif_model=".output" num_pb="1">
|
|
<input name="outpad" num_pins="1"/>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="outpad" input="io.outpad" output="outpad.outpad">
|
|
<delay_constant max="1.394e-11" in_port="io.outpad" out_port="outpad.outpad"/>
|
|
</direct>
|
|
</interconnect>
|
|
</mode>
|
|
<!-- Every input pin is driven by 15% of the tracks in a channel, every output pin is driven by 10% of the tracks in a channel -->
|
|
<!-- IOs go on the periphery of the FPGA, for consistency,
|
|
make it physically equivalent on all sides so that only one definition of I/Os is needed.
|
|
If I do not make a physically equivalent definition, then I need to define 4 different I/Os, one for each side of the FPGA
|
|
-->
|
|
<!-- Place I/Os on the sides of the FPGA -->
|
|
<power method="ignore"/>
|
|
</pb_type>
|
|
<!-- Define I/O pads ends -->
|
|
<!-- Define general purpose logic block (CLB) begin -->
|
|
<!--- Area calculation: Total Stratix IV tile area is about 8100 um^2, and a minimum width transistor
|
|
area is 60 L^2 yields a tile area of 84375 MWTAs.
|
|
Routing at W=300 is 30481 MWTAs, leaving us with a total of 53000 MWTAs for logic block area
|
|
This means that only 37% of our area is in the general routing, and 63% is inside the logic
|
|
block. Note that the crossbar / local interconnect is considered part of the logic block
|
|
area in this analysis. That is a lower proportion of of routing area than most academics
|
|
assume, but note that the total routing area really includes the crossbar, which would push
|
|
routing area up significantly, we estimate into the ~70% range.
|
|
-->
|
|
<pb_type name="clb">
|
|
<input name="I" num_pins="10" equivalent="full"/>
|
|
<output name="O" num_pins="4" equivalent="none"/>
|
|
<clock name="clk" num_pins="1"/>
|
|
<!-- Describe basic logic element.
|
|
Each basic logic element has a 4-LUT that can be optionally registered
|
|
-->
|
|
<pb_type name="fle" num_pb="4">
|
|
<input name="in" num_pins="4"/>
|
|
<output name="out" num_pins="1"/>
|
|
<clock name="clk" num_pins="1"/>
|
|
<!-- 4-LUT mode definition begin -->
|
|
<mode name="n1_lut4">
|
|
<!-- Define 4-LUT mode -->
|
|
<pb_type name="ble4" num_pb="1">
|
|
<input name="in" num_pins="4"/>
|
|
<output name="out" num_pins="1"/>
|
|
<clock name="clk" num_pins="1"/>
|
|
<!-- Define LUT -->
|
|
<pb_type name="lut4" blif_model=".names" num_pb="1" class="lut">
|
|
<input name="in" num_pins="4" port_class="lut_in"/>
|
|
<output name="out" num_pins="1" port_class="lut_out"/>
|
|
<!-- LUT timing using delay matrix -->
|
|
<delay_matrix type="max" in_port="lut4.in" out_port="lut4.out">
|
|
261e-12
|
|
261e-12
|
|
261e-12
|
|
261e-12
|
|
</delay_matrix>
|
|
</pb_type>
|
|
<!-- Define flip-flop -->
|
|
<pb_type name="ff" blif_model=".latch" num_pb="1" class="flipflop">
|
|
<input name="D" num_pins="1" port_class="D"/>
|
|
<output name="Q" num_pins="1" port_class="Q"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="66e-12" port="ff.D" clock="clk"/>
|
|
<T_clock_to_Q max="124e-12" port="ff.Q" clock="clk"/>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="direct1" input="ble4.in" output="lut4[0:0].in"/>
|
|
<direct name="direct2" input="lut4.out" output="ff.D">
|
|
<!-- Advanced user option that tells CAD tool to find LUT+FF pairs in netlist -->
|
|
<pack_pattern name="ble4" in_port="lut4.out" out_port="ff.D"/>
|
|
</direct>
|
|
<direct name="direct3" input="ble4.clk" output="ff.clk"/>
|
|
<mux name="mux1" input="ff.Q lut4.out" output="ble4.out">
|
|
<!-- LUT to output is faster than FF to output on a Stratix IV -->
|
|
<delay_constant max="25e-12" in_port="lut4.out" out_port="ble4.out"/>
|
|
<delay_constant max="45e-12" in_port="ff.Q" out_port="ble4.out"/>
|
|
</mux>
|
|
</interconnect>
|
|
</pb_type>
|
|
<interconnect>
|
|
<direct name="direct1" input="fle.in" output="ble4.in"/>
|
|
<direct name="direct2" input="ble4.out" output="fle.out[0:0]"/>
|
|
<direct name="direct3" input="fle.clk" output="ble4.clk"/>
|
|
</interconnect>
|
|
</mode>
|
|
<!-- 6-LUT mode definition end -->
|
|
</pb_type>
|
|
<interconnect>
|
|
<!-- We use a full crossbar to get logical equivalence at inputs of CLB
|
|
The delays below come from Stratix IV. the delay through a connection block
|
|
input mux + the crossbar in Stratix IV is 167 ps. We already have a 72 ps
|
|
delay on the connection block input mux (modeled by Ian Kuon), so the remaining
|
|
delay within the crossbar is 95 ps.
|
|
The delays of cluster feedbacks in Stratix IV is 100 ps, when driven by a LUT.
|
|
Since all our outputs LUT outputs go to a BLE output, and have a delay of
|
|
25 ps to do so, we subtract 25 ps from the 100 ps delay of a feedback
|
|
to get the part that should be marked on the crossbar. -->
|
|
<complete name="crossbar" input="clb.I fle[3:0].out" output="fle[3:0].in">
|
|
<delay_constant max="95e-12" in_port="clb.I" out_port="fle[3:0].in"/>
|
|
<delay_constant max="75e-12" in_port="fle[3:0].out" out_port="fle[3:0].in"/>
|
|
</complete>
|
|
<complete name="clks" input="clb.clk" output="fle[3:0].clk">
|
|
</complete>
|
|
<!-- This way of specifying direct connection to clb outputs is important because this architecture uses automatic spreading of opins.
|
|
By grouping to output pins in this fashion, if a logic block is completely filled by 6-LUTs,
|
|
then the outputs those 6-LUTs take get evenly distributed across all four sides of the CLB instead of clumped on two sides (which is what happens with a more
|
|
naive specification).
|
|
-->
|
|
<direct name="clbouts1" input="fle[3:0].out" output="clb.O"/>
|
|
</interconnect>
|
|
<!-- Every input pin is driven by 15% of the tracks in a channel, every output pin is driven by 10% of the tracks in a channel -->
|
|
<!-- Place this general purpose logic block in any unspecified column -->
|
|
</pb_type>
|
|
<!-- Define general purpose logic block (CLB) ends -->
|
|
<!-- Define 8-bit multiplier with input and output registers begin -->
|
|
<pb_type name="mult_8">
|
|
<input name="a" num_pins="8"/>
|
|
<input name="b" num_pins="8"/>
|
|
<clock name="clk" num_pins="1"/>
|
|
<output name="out" num_pins="16"/>
|
|
<mode name="mult_8x8">
|
|
<pb_type name="mult_8x8_slice" num_pb="1">
|
|
<input name="A_cfg" num_pins="8"/>
|
|
<input name="B_cfg" num_pins="8"/>
|
|
<output name="OUT_cfg" num_pins="16"/>
|
|
<clock name="clk" num_pins="1"/>
|
|
<pb_type name="mult_8x8" blif_model=".subckt mult_8" num_pb="1">
|
|
<input name="A" num_pins="36"/>
|
|
<input name="B" num_pins="36"/>
|
|
<output name="Y" num_pins="72"/>
|
|
<delay_constant max="1.523e-9" min="0.776e-9" in_port="mult_8x8.A" out_port="mult_8x8.Y"/>
|
|
<delay_constant max="1.523e-9" min="0.776e-9" in_port="mult_8x8.B" out_port="mult_8x8.Y"/>
|
|
</pb_type>
|
|
<pb_type name="ff_A" blif_model=".latch" num_pb="8" class="flipflop">
|
|
<input name="D" num_pins="1" port_class="D"/>
|
|
<output name="Q" num_pins="1" port_class="Q"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="66e-12" port="ff_A.D" clock="clk"/>
|
|
<T_clock_to_Q max="124e-12" port="ff_A.Q" clock="clk"/>
|
|
</pb_type>
|
|
<pb_type name="ff_B" blif_model=".latch" num_pb="8" class="flipflop">
|
|
<input name="D" num_pins="1" port_class="D"/>
|
|
<output name="Q" num_pins="1" port_class="Q"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="66e-12" port="ff_B.D" clock="clk"/>
|
|
<T_clock_to_Q max="124e-12" port="ff_B.Q" clock="clk"/>
|
|
</pb_type>
|
|
<pb_type name="ff_Y" blif_model=".latch" num_pb="16" class="flipflop">
|
|
<input name="D" num_pins="1" port_class="D"/>
|
|
<output name="Q" num_pins="1" port_class="Q"/>
|
|
<clock name="clk" num_pins="1" port_class="clock"/>
|
|
<T_setup value="66e-12" port="ff_Y.D" clock="clk"/>
|
|
<T_clock_to_Q max="124e-12" port="ff_Y.Q" clock="clk"/>
|
|
</pb_type>
|
|
<interconnect>
|
|
<mux name="a2a0" input="mult_8x8_slice.A_cfg[0] ff_A[0].Q" output="mult_8x8.A[0]"/>
|
|
<mux name="a2a1" input="mult_8x8_slice.A_cfg[1] ff_A[1].Q" output="mult_8x8.A[1]"/>
|
|
<mux name="a2a2" input="mult_8x8_slice.A_cfg[2] ff_A[2].Q" output="mult_8x8.A[2]"/>
|
|
<mux name="a2a3" input="mult_8x8_slice.A_cfg[3] ff_A[3].Q" output="mult_8x8.A[3]"/>
|
|
<mux name="a2a4" input="mult_8x8_slice.A_cfg[4] ff_A[4].Q" output="mult_8x8.A[4]"/>
|
|
<mux name="a2a5" input="mult_8x8_slice.A_cfg[5] ff_A[5].Q" output="mult_8x8.A[5]"/>
|
|
<mux name="a2a6" input="mult_8x8_slice.A_cfg[6] ff_A[6].Q" output="mult_8x8.A[6]"/>
|
|
<mux name="a2a7" input="mult_8x8_slice.A_cfg[7] ff_A[7].Q" output="mult_8x8.A[7]"/>
|
|
<direct name="a2ff" input="mult_8x8_slice.A_cfg[7:0]" output="ff_A[7:0].D"/>
|
|
<mux name="b2b0" input="mult_8x8_slice.B_cfg[0] ff_B[0].Q" output="mult_8x8.B[0]"/>
|
|
<mux name="b2b1" input="mult_8x8_slice.B_cfg[1] ff_B[1].Q" output="mult_8x8.B[1]"/>
|
|
<mux name="b2b2" input="mult_8x8_slice.B_cfg[2] ff_B[2].Q" output="mult_8x8.B[2]"/>
|
|
<mux name="b2b3" input="mult_8x8_slice.B_cfg[3] ff_B[3].Q" output="mult_8x8.B[3]"/>
|
|
<mux name="b2b4" input="mult_8x8_slice.B_cfg[4] ff_B[4].Q" output="mult_8x8.B[4]"/>
|
|
<mux name="b2b5" input="mult_8x8_slice.B_cfg[5] ff_B[5].Q" output="mult_8x8.B[5]"/>
|
|
<mux name="b2b6" input="mult_8x8_slice.B_cfg[6] ff_B[6].Q" output="mult_8x8.B[6]"/>
|
|
<mux name="b2b7" input="mult_8x8_slice.B_cfg[7] ff_B[7].Q" output="mult_8x8.B[7]"/>
|
|
<direct name="b2ff" input="mult_8x8_slice.B_cfg[7:0]" output="ff_B[7:0].D"/>
|
|
<mux name="out2out0" input="mult_8x8.Y[0] ff_Y[0].Q" output="mult_8x8_slice.OUT_cfg[0]"/>
|
|
<mux name="out2out1" input="mult_8x8.Y[1] ff_Y[1].Q" output="mult_8x8_slice.OUT_cfg[1]"/>
|
|
<mux name="out2out2" input="mult_8x8.Y[2] ff_Y[2].Q" output="mult_8x8_slice.OUT_cfg[2]"/>
|
|
<mux name="out2out3" input="mult_8x8.Y[3] ff_Y[3].Q" output="mult_8x8_slice.OUT_cfg[3]"/>
|
|
<mux name="out2out4" input="mult_8x8.Y[4] ff_Y[4].Q" output="mult_8x8_slice.OUT_cfg[4]"/>
|
|
<mux name="out2out5" input="mult_8x8.Y[5] ff_Y[5].Q" output="mult_8x8_slice.OUT_cfg[5]"/>
|
|
<mux name="out2out6" input="mult_8x8.Y[6] ff_Y[6].Q" output="mult_8x8_slice.OUT_cfg[6]"/>
|
|
<mux name="out2out7" input="mult_8x8.Y[7] ff_Y[7].Q" output="mult_8x8_slice.OUT_cfg[7]"/>
|
|
<mux name="out2out8" input="mult_8x8.Y[8] ff_Y[8].Q" output="mult_8x8_slice.OUT_cfg[8]"/>
|
|
<mux name="out2out9" input="mult_8x8.Y[9] ff_Y[9].Q" output="mult_8x8_slice.OUT_cfg[9]"/>
|
|
<mux name="out2out10" input="mult_8x8.Y[10] ff_Y[10].Q" output="mult_8x8_slice.OUT_cfg[10]"/>
|
|
<mux name="out2out11" input="mult_8x8.Y[11] ff_Y[11].Q" output="mult_8x8_slice.OUT_cfg[11]"/>
|
|
<mux name="out2out12" input="mult_8x8.Y[12] ff_Y[12].Q" output="mult_8x8_slice.OUT_cfg[12]"/>
|
|
<mux name="out2out13" input="mult_8x8.Y[13] ff_Y[13].Q" output="mult_8x8_slice.OUT_cfg[13]"/>
|
|
<mux name="out2out14" input="mult_8x8.Y[14] ff_Y[14].Q" output="mult_8x8_slice.OUT_cfg[14]"/>
|
|
<mux name="out2out15" input="mult_8x8.Y[15] ff_Y[15].Q" output="mult_8x8_slice.OUT_cfg[15]"/>
|
|
<direct name="out2ff" input="mult_8x8.Y[15:0]" output="ff_Y[15:0].D"/>
|
|
<complete name="clk_ff_A" input="mult_8x8_slice.clk" output="ff_A.clk"/>
|
|
<complete name="clk_ff_B" input="mult_8x8_slice.clk" output="ff_B.clk"/>
|
|
<complete name="clk_ff_Y" input="mult_8x8_slice.clk" output="ff_Y.clk"/>
|
|
</interconnect>
|
|
<power method="pin-toggle">
|
|
<port name="A_cfg" energy_per_toggle="2.13e-12"/>
|
|
<port name="B_cfg" energy_per_toggle="2.13e-12"/>
|
|
<static_power power_per_instance="0.0"/>
|
|
</power>
|
|
</pb_type>
|
|
<interconnect>
|
|
<!-- Stratix IV input delay of 207ps is conservative for this architecture because this architecture does not have an input crossbar in the multiplier.
|
|
Subtract 72.5 ps delay, which is already in the connection block input mux, leading
|
|
to a 134 ps delay.
|
|
The interconnect difference for DSP blocks is 0.5523, which leads to a minimum delay of 74 ps
|
|
-->
|
|
<direct name="a2a" input="mult_8.a" output="mult_8x8_slice.A_cfg">
|
|
<delay_constant max="134e-12" min="74e-12" in_port="mult_8.a" out_port="mult_8x8_slice.A_cfg"/>
|
|
</direct>
|
|
<direct name="b2b" input="mult_8.b" output="mult_8x8_slice.B_cfg">
|
|
<delay_constant max="134e-12" min="74e-12" in_port="mult_8.b" out_port="mult_8x8_slice.B_cfg"/>
|
|
</direct>
|
|
<direct name="out2out" input="mult_8x8_slice.OUT_cfg" output="mult_8.out">
|
|
<delay_constant max="1.93e-9" min="74e-12" in_port="mult_8x8_slice.OUT_cfg" out_port="mult_8.out"/>
|
|
</direct>
|
|
<complete name="clk" input="mult_8.clk" output="mult_8x8_slice.clk"/>
|
|
</interconnect>
|
|
</mode>
|
|
<!-- Place this multiplier block every 8 columns from (and including) the sixth column -->
|
|
<power method="sum-of-children"/>
|
|
</pb_type>
|
|
<!-- Define fracturable multiplier end -->
|
|
|
|
</complexblocklist>
|
|
</architecture>
|