41 lines
3.3 KiB
Markdown
41 lines
3.3 KiB
Markdown
# Naming convention for OpenFPGA architecture files
|
|
Please reveal the following architecture features in the names to help quickly spot architecture files.
|
|
Note that an OpenFPGA architecture can be applied to multiple VPR architecture files.
|
|
|
|
- k<lut\_size>\_<frac><Native>: Look-Up Table (LUT) size of FPGA. If you have fracturable LUTs or multiple LUT circuits, this should be largest input size.
|
|
* The keyword 'frac' is to specify if fracturable LUT is used or not.
|
|
* The keyword 'Native' is to specify if fracturable LUT design is a native one (without mode switch) or a standard one (with mode switch).
|
|
- N<le\_size>: Number of logic elements for a CLB. If you have multiple CLB architectures, this should be largest number.
|
|
- fracff<2edge>: Use multi-mode flip-flop model, where reset/set polarity is configurable. When 2edge is specified, clock polarity can be switched between postive edge triggered and negative edge triggered
|
|
- adder\_chain: If hard adder/carry chain is used inside CLBs
|
|
- register\_chain: If shift register chain is used inside CLBs
|
|
- scan\_chain: If scan chain testing infrastructure is used inside CLBs
|
|
- <wide>\_<frac>\_dsp<dsp\_size>reg: If Digital Signal Processor (DSP) is used or not. If used, the input size should be clarified here.
|
|
- The keyword 'wide' is to specify if the DSP spans more than 1 column.
|
|
- The keyword 'frac' is to specify if the DSP is fracturable to operate in different modes.
|
|
- The keyword 'reg' is to specify if the DSP has input and output registers. If only input or output registers are used, the keyword will be 'regin' or 'regout' respectively.
|
|
- mem<mem\_size>: If block RAM (BRAM) is used or not. If used, the memory size should be clarified here. The keyword wide is to specify if the BRAM spanns more than 1 column.
|
|
- aib: If the Advanced Interface Bus (AIB) is used in place of some I/Os.
|
|
- <bank\|cc\|frame\|standalone>: specify the type of configuration protocol used in the architecture.
|
|
- `bank` refers to the memory bank
|
|
- `cc` refers to the configuration chain
|
|
- `frame` refers to the frame-based organization
|
|
- `standalone` referes to the vanilla organization
|
|
- fixed\_sim: fixed clock frequencies in simulation settings. If auto clock frequencies are used, there is no need to appear in the naming
|
|
- intermediate buffer: If intermediate buffers are used in LUT designs.
|
|
- behavioral: If behavioral Verilog modeling is specified
|
|
- local\_encoder: If local encoders are used in routing multiplexer design
|
|
- spyio/spypad: If spy I/Os are used
|
|
- registerable\_io: If I/Os are registerable (can be either combinational or sequential)
|
|
- stdcell: If circuit designs are built with standard cells only
|
|
- tree\_mux: If routing multiplexers are built with a tree-like structure
|
|
- localClkGen: The clock signal of CLB can be generated by internal programmable resources
|
|
- <feature_size>: The technology node which the delay numbers are extracted from.
|
|
- powergate : The FPGA has power-gating techniques applied. If not defined, there is no power-gating.
|
|
- GlobalTile<Int>Clk<Pin>: How many clocks are defined through global ports from physical tiles.
|
|
* <Int> is the number of clocks
|
|
* <Pin> When specified, multiple clocks are in separated pins with different names
|
|
- abspath: All the paths in the architecture file are absolute and hardcoded.
|
|
|
|
Other features are used in naming should be listed here.
|