diff --git a/openfpga_flow/openfpga_arch/k6_frac_N10_adder_chain_dpram8K_40nm_openfpga.xml b/openfpga_flow/openfpga_arch/k6_frac_N10_adder_chain_dpram8K_dsp36_40nm_openfpga.xml
similarity index 93%
rename from openfpga_flow/openfpga_arch/k6_frac_N10_adder_chain_dpram8K_40nm_openfpga.xml
rename to openfpga_flow/openfpga_arch/k6_frac_N10_adder_chain_dpram8K_dsp36_40nm_openfpga.xml
index 37beb67bf..ed8f0134c 100644
--- a/openfpga_flow/openfpga_arch/k6_frac_N10_adder_chain_dpram8K_40nm_openfpga.xml
+++ b/openfpga_flow/openfpga_arch/k6_frac_N10_adder_chain_dpram8K_dsp36_40nm_openfpga.xml
@@ -206,6 +206,16 @@
       <port type="output" prefix="data_out" size="8"/>
       <port type="clock" prefix="clk" size="1" is_global="true" default_val="0"/>
     </circuit_model>
+    <circuit_model type="hard_logic" name="mult_36x36" prefix="mult_36x36" spice_netlist="${OPENFPGA_PATH}/openfpga_flow/openfpga_cell_library/spice/mult_36x36.sp" verilog_netlist="${OPENFPGA_PATH}/openfpga_flow/openfpga_cell_library/verilog/mult_36x36.v">
+      <design_technology type="cmos"/>
+      <input_buffer exist="true" circuit_model_name="INVTX1"/>
+      <output_buffer exist="true" circuit_model_name="INVTX1"/>
+      <port type="input" prefix="A" lib_name="A" size="36"/>
+      <port type="input" prefix="B" lib_name="B" size="36"/>
+      <port type="output" prefix="Y" lib_name="out" size="72"/>
+      <!-- As a fracturable multiplier, it requires 2 configuration bits to operate in 4 different modes -->
+      <port type="sram" prefix="mode" size="2" mode_select="true" circuit_model_name="DFFR" default_val="1"/>
+    </circuit_model>
   </circuit_library>
   <configuration_protocol>
     <organization type="scan_chain" circuit_model_name="DFFR"/>
@@ -265,6 +275,10 @@
     <pb_type name="clb.fle[n1_lut6].ble6.ff" physical_pb_type_name="clb.fle[physical].fabric.ff" physical_pb_type_index_factor="2" physical_pb_type_index_offset="0"/>
     <!-- End physical pb_type binding in complex block clb -->
 
+    <!-- physical pb_type binding in complex block dsp -->
+    <pb_type name="mult_36" physical_mode_name="mult_36x36" idle_mode_name="mult_36x36"/>
+    <!-- Bind the primitive pb_type in the physical mode to a circuit model --> 
+    <pb_type name="mult_36[mult_36x36].mult_36x36_slice.mult_36x36" circuit_model_name="mult_36x36" mode_bits="00"/>
 
     <!-- physical pb_type binding in complex block memory -->
     <pb_type name="memory[mem_1024x8_dp].mem_1024x8_dp" circuit_model_name="dpram_1024x8"/>
diff --git a/openfpga_flow/vpr_arch/k6_frac_N10_tileable_adder_chain_dpram8K_40nm.xml b/openfpga_flow/vpr_arch/k6_frac_N10_tileable_adder_chain_dpram8K_dsp36_40nm.xml
similarity index 91%
rename from openfpga_flow/vpr_arch/k6_frac_N10_tileable_adder_chain_dpram8K_40nm.xml
rename to openfpga_flow/vpr_arch/k6_frac_N10_tileable_adder_chain_dpram8K_dsp36_40nm.xml
index d697a1e8d..a34b29c22 100644
--- a/openfpga_flow/vpr_arch/k6_frac_N10_tileable_adder_chain_dpram8K_40nm.xml
+++ b/openfpga_flow/vpr_arch/k6_frac_N10_tileable_adder_chain_dpram8K_dsp36_40nm.xml
@@ -138,6 +138,15 @@
         <port name="data_out" clock="clk"/>
       </output_ports>
     </model>
+    <model name="mult_36">
+      <input_ports>
+        <port name="A" combinational_sink_ports="Y"/>
+        <port name="B" combinational_sink_ports="Y"/>
+      </input_ports>
+      <output_ports>
+        <port name="Y"/>
+      </output_ports>
+    </model>
   </models>
   <tiles>
     <tile name="io" capacity="8" area="0">
@@ -196,6 +205,23 @@
         <loc side="bottom">memory.waddr[9:5] memory.raddr[9:5] memory.data_in[7:4] memory.ren memory.data_out[7:4]</loc>
       </pinlocations>
     </tile>
+    <tile name="mult_36" height="6" area="396000">
+      <equivalent_sites>
+        <site pb_type="mult_36" pin_mapping="direct"/>
+      </equivalent_sites>
+      <input name="a" num_pins="36"/>
+      <input name="b" num_pins="36"/>
+      <output name="out" num_pins="72"/>
+      <fc in_type="frac" in_val="0.15" out_type="frac" out_val="0.10"/>
+      <!--  Highly recommand to customize pin location when direct connection is used!!! -->
+      <!-- pinlocations are designed to spread pin on 4 sides evenly -->
+      <pinlocations pattern="custom">
+        <loc side="left">mult_36.b[0:9] mult_36.b[10:35] mult_36.out[36:71]</loc>
+        <loc side="top"></loc>
+        <loc side="right">mult_36.a[0:9] mult_36.a[10:35] mult_36.out[0:35]</loc>
+        <loc side="bottom"></loc>
+      </pinlocations>
+    </tile>
   </tiles>
   <!-- ODIN II specific config ends -->
   <!-- Physical descriptions begin -->
@@ -208,6 +234,8 @@
       <fill type="clb" priority="10"/>
       <!--Column of 'memory' with 'EMPTY' blocks wherever a 'memory' does not fit. Vertical offset by 1 for perimeter.-->
       <col type="memory" startx="2" starty="1" repeatx="8" priority="20"/>
+      <!--Column of 'mult_36' with 'EMPTY' blocks wherever a 'mult_36' does not fit. Vertical offset by 1 for perimeter.-->
+      <col type="mult_36" startx="6" starty="1" repeatx="8" priority="20"/>
       <col type="EMPTY" startx="2" repeatx="8" starty="1" priority="19"/>
     </auto_layout>
     <fixed_layout name="3x2" width="5" height="4">
@@ -686,6 +714,58 @@
       </interconnect>
     </pb_type>
     <!-- Define general purpose logic block (CLB) ends -->
+    <!-- Define 36-bit multiplier begin -->
+    <pb_type name="mult_36">
+      <input name="a" num_pins="36"/>
+      <input name="b" num_pins="36"/>
+      <output name="out" num_pins="72"/>
+      <mode name="mult_36x36">
+        <pb_type name="mult_36x36_slice" num_pb="1">
+          <input name="A_cfg" num_pins="36"/>
+          <input name="B_cfg" num_pins="36"/>
+          <output name="OUT_cfg" num_pins="72"/>
+          <pb_type name="mult_36x36" blif_model=".subckt mult_36" num_pb="1">
+            <input name="A" num_pins="36"/>
+            <input name="B" num_pins="36"/>
+            <output name="Y" num_pins="72"/>
+            <delay_constant max="1.523e-9" min="0.776e-9" in_port="mult_36x36.A" out_port="mult_36x36.Y"/>
+            <delay_constant max="1.523e-9" min="0.776e-9" in_port="mult_36x36.B" out_port="mult_36x36.Y"/>
+          </pb_type>
+          <interconnect>
+            <direct name="a2a" input="mult_36x36_slice.A_cfg" output="mult_36x36.A">
+            </direct>
+            <direct name="b2b" input="mult_36x36_slice.B_cfg" output="mult_36x36.B">
+            </direct>
+            <direct name="out2out" input="mult_36x36.Y" output="mult_36x36_slice.OUT_cfg">
+            </direct>
+          </interconnect>
+          <power method="pin-toggle">
+            <port name="A_cfg" energy_per_toggle="2.13e-12"/>
+            <port name="B_cfg" energy_per_toggle="2.13e-12"/>
+            <static_power power_per_instance="0.0"/>
+          </power>
+        </pb_type>
+        <interconnect>
+          <!-- Stratix IV input delay of 207ps is conservative for this architecture because this architecture does not have an input crossbar in the multiplier. 
+		   Subtract 72.5 ps delay, which is already in the connection block input mux, leading
+		   to a 134 ps delay.
+				The interconnect difference for DSP blocks is 0.5523, which leads to a minimum delay of 74 ps
+              -->
+          <direct name="a2a" input="mult_36.a" output="mult_36x36_slice.A_cfg">
+            <delay_constant max="134e-12" min="74e-12" in_port="mult_36.a" out_port="mult_36x36_slice.A_cfg"/>
+          </direct>
+          <direct name="b2b" input="mult_36.b" output="mult_36x36_slice.B_cfg">
+            <delay_constant max="134e-12" min="74e-12" in_port="mult_36.b" out_port="mult_36x36_slice.B_cfg"/>
+          </direct>
+          <direct name="out2out" input="mult_36x36_slice.OUT_cfg" output="mult_36.out">
+            <delay_constant max="1.93e-9" min="74e-12" in_port="mult_36x36_slice.OUT_cfg" out_port="mult_36.out"/>
+          </direct>
+        </interconnect>
+      </mode>
+      <!-- Place this multiplier block every 8 columns from (and including) the sixth column -->
+      <power method="sum-of-children"/>
+    </pb_type>
+    <!-- Define fracturable multiplier end -->
     <!-- Define single-mode dual-port memory begin -->
     <pb_type name="memory">
       <input name="waddr" num_pins="10"/>
diff --git a/openfpga_flow/vpr_arch/k6_frac_N10_tileable_adder_register_scan_chain_mem16K_depop50_12nm.xml b/openfpga_flow/vpr_arch/k6_frac_N10_tileable_adder_register_scan_chain_mem16K_depop50_12nm.xml
index baada7911..b6dad0a8f 100755
--- a/openfpga_flow/vpr_arch/k6_frac_N10_tileable_adder_register_scan_chain_mem16K_depop50_12nm.xml
+++ b/openfpga_flow/vpr_arch/k6_frac_N10_tileable_adder_register_scan_chain_mem16K_depop50_12nm.xml
@@ -193,7 +193,16 @@
       <!--Column of 'memory' with 'EMPTY' blocks wherever a 'memory' does not fit. Vertical offset by 1 for perimeter.-->
       <col type="memory" startx="16" starty="1" repeatx="16" priority="20"/>
       <col type="EMPTY" startx="16" repeatx="16" starty="1" priority="19"/>
-    </auto_layout-->
+    </auto_layout>
+    <fixed_layout name="6x6" width="8" height="8">
+      <!--Perimeter of 'io' blocks with 'EMPTY' blocks at corners-->
+      <perimeter type="io" priority="100"/>
+      <corners type="EMPTY" priority="101"/>
+      <!--Fill with 'clb'-->
+      <fill type="clb" priority="10"/>
+      <!--Column of 'memory' with 'EMPTY' blocks wherever a 'memory' does not fit. Vertical offset by 1 for perimeter.-->
+      <col type="EMPTY" startx="16" repeatx="16" starty="1" priority="19"/>
+    </fixed_layout>
     <!-- Apply a fixed layout of 2x2 core array.
          VPR8 considers the I/O ring in the array size
          Therefore the height and width are both 4