riscv
/
OpenFPGA
mirror of https://github.com/lnis-uofu/OpenFPGA.git
1
0
Fork 0
Code Issues Projects Releases Wiki Activity

Add scan-chain and timed architecture + update simulation script script (add script for autochecked testbench)

This commit is contained in:
AurelienUoU 2018-12-08 22:57:54 -07:00
parent 10866d1852
commit 5e94b7093d
8 changed files with 4027 additions and 10 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

1453
vpr7_x2p/vpr/ARCH/k6_N10_scan_chain_tsmc40nm_TT.xml Normal file
View File

File diff suppressed because it is too large Load Diff

882
vpr7_x2p/vpr/ARCH/k6_N10_sram_chain_SC_gf130_2x2.xml Normal file
View File

@ -0,0 +1,882 @@
<!--
Flagship Heterogeneous Architecture with Carry Chains for VTR 7.0.
- 40 nm technology
- General purpose logic block:
K = 6, N = 10, fracturable 6 LUTs (can operate as one 6-LUT or two 5-LUTs with all 5 inputs shared)
with optionally registered outputs
Each 5-LUT has an arithemtic mode that converts it to a single-bit adder with both inputs driven by 4-LUTs (both 4-LUTs share all 4 inputs)
Carry chain links to vertically adjacent logic blocks
- Memory size 32 Kbits, memory aspect ratios vary from a data width of 1 to data width of 64.
Height = 6, found on every (8n+2)th column
- Multiplier modes: one 36x36, two 18x18, each 18x18 can also operate as two 9x9.
Height = 4, found on every (8n+6)th column
- Routing architecture: L = 4, fc_in = 0.15, Fc_out = 0.1
Details on Modelling:
The electrical design of the architecture described here is NOT from an
optimized, SPICED architecture. Instead, we attempt to create a reasonable
architecture file by using an existing commercial FPGA to approximate the area,
delay, and power of the underlying components. This is combined with a reasonable 40 nm
model of wiring and circuit design for low-level routing components, where available.
The resulting architecture has delays that roughly match a commercial 40 nm FPGA, but also
has wiring electrical parameters that allow the wire lengths and switch patterns to be
modified and you will still get reasonable delay results for the new architecture.
The following describes, in detail, how we obtained the various electrical values for this
architecture.
Rmin for nmos and pmos, routing buffer sizes, and I/O pad delays are from the ifar
architecture created by Ian Kuon: K06 N10 45nm fc 0.15 area-delay optimized architecture.
(n10k06l04.fc15.area1delay1.cmos45nm.bptm.cmos45nm.xml)
This routing architecture was optimized for 45 nm, and we have scaled it linearly to 40 nm to
match the overall target (a 40 nm FPGA).
We obtain delay numbers by measuring delays of routing, soft logic blocks,
memories, and multipliers from test circuits on a Stratix IV GX device
(EP4SGX230DF29C2X, i.e. fastest speed grade). For routing, we took the average delay of H4 and V4
wires. Rmetal and Cmetal values for the routing wires were obtained from work done by Charles
Chiasson. We use a 96 nm half-pitch (corresponding to mid-level metal stack 40 nm routing) and
take the R and C data from the ITRS roadmap.
For the general purpose logic block, we assume that the area and delays of the Stratix IV
crossbar is close enough to the crossbar modelled here. We use 40 inputs and 20 feedback lines in
the cluster and a full crossbar, leading to 53:1 multiplexers in front of each BLE input.
Stratix IV uses 52 inputs and 20 feedback lines, but only a half-populated crossbar, leading to
36:1 multiplexers. We require 60 such multiplexers, while Stratix IV requires 88 for its more
complex fracturable BLEs + the extra control signals. We justify this rough approximation as follows:
The Stratix IV crossbar has more inputs (72 vs. 60) and
outputs (88 vs. 60) than our full crossbar which should increase its area and delay, but the
Stratix IV crossbar is also 50% sparse (each mux is 36:1 instead of 53:1) which should reduce its
area and delay. The total number of crossbar switch points is roughly similar between the two
architectures (3160 for SIV and 3600 for the academic architecture below), so we use the area
& delay of the Stratix IV crossbar as a rough approximation of our crossbar.
For LUTs, we include LUT
delays measured from Stratix IV which is dependant on the input used (ie. some
LUT inputs are faster than others). The CAD tools at the time of VTR 7 does
not consider differences in LUT input delays.
Adder delays obtained as approximate values from a Stratix IV EP4SE230F29C3 device.
Delay obtained by compiling a 256 bit adder (registered inputs and outputs,
all pins except clock virtual) then measuring the delays in chip-planner,
sumout delay = 0.271ns to 0.348 ns, intra-block carry delay = 0.011 ns,
inter-block carry delay = 0.327 ns. Given this data, I will approximate
sumout 0.3 ns, intra-block carry-delay = 0.01 ns, and
inter-block carry-delay = 0.16 ns (since Altera inter-block carry delay has
overhead that we don't have, I'll approximate the delay of a simpler chain at
one half what they have. This is very rough, anything from 0.01ns to 0.327ns
can be justified).
Logic block area numbers obtained by scaling overall tile area of a 65nm
Stratix III device, (as given in Wong, Betz and Rose, FPGA 2011) to 40 nm, then subtracting out
routing area at a channel width of 300. We use a channel width of 300 because it can route
all the VTR 6.0 benchmark circuits with an approximately 20% safety margin, and is also close to the
total channel width of Stratix IV. Hence this channel width is close to the commercial practice of
choosing a width that provides high routability. The architecture can be routed at different channel
widths, but we estimate the tile size and hence the physical length of routing wires assuming
a channel width of 300.
Sanity checks employed:
1. We confirmed the routing buffer delay is ~1/3rd of total routing delay at L = 4. This matches
common electrical design.
Authors: Jason Luu, Jeff Goeders, Vaughn Betz
-->
<architecture>
<!--
ODIN II specific config begins
Describes the types of user-specified netlist blocks (in blif, this corresponds to
".model [type_of_block]") that this architecture supports.
Note: Basic LUTs, I/Os, and flip-flops are not included here as there are
already special structures in blif (.names, .input, .output, and .latch)
that describe them.
-->
<models>
<model name="io">
<input_ports>
<port name="outpad"/>
</input_ports>
<output_ports>
<port name="inpad"/>
</output_ports>
</model>
<model name="adder">
<input_ports>
<port name="a"/>
<port name="b"/>
<port name="cin"/>
</input_ports>
<output_ports>
<port name="cout"/>
<port name="sumout"/>
</output_ports>
</model>
<model name="frac_lut6">
<input_ports>
<port name="in"/>
</input_ports>
<output_ports>
<port name="lut6_out"/>
<port name="lut5_out"/>
<port name="lut4_out"/>
</output_ports>
</model>
</models>
<!-- ODIN II specific config ends -->
<!-- Physical descriptions begin -->
<layout width="2" height="2"/>
<spice_settings>
<parameters>
<options sim_temp="25" post="off" captab="off" fast="on"/>
<monte_carlo mc_sim="off" num_mc_points="2" cmos_variation="off" rram_variation="off">
<cmos abs_variation="0.1" num_sigma="3"/>
<rram abs_variation="0.1" num_sigma="3"/>
</monte_carlo>
<measure sim_num_clock_cycle="auto" accuracy="1e-13" accuracy_type="abs">
<slew>
<rise upper_thres_pct="0.95" lower_thres_pct="0.05"/>
<fall upper_thres_pct="0.05" lower_thres_pct="0.95"/>
</slew>
<delay>
<rise input_thres_pct="0.5" output_thres_pct="0.5"/>
<fall input_thres_pct="0.5" output_thres_pct="0.5"/>
</delay>
</measure>
<stimulate>
<clock op_freq="auto" sim_slack="0.2" prog_freq="2.5e6">
<rise slew_time="20e-12" slew_type="abs"/>
<fall slew_time="20e-12" slew_type="abs"/>
</clock>
<input>
<rise slew_time="25e-12" slew_type="abs"/>
<fall slew_time="25e-12" slew_type="abs"/>
</input>
</stimulate>
</parameters>
<tech_lib lib_type="industry" transistor_type="TOP_TT" lib_path="/research/ece/lnis/USERS/tang/tangxifan-eda-tools/branches/subvt_fpga/process/tsmc40nm/toplevel.l" nominal_vdd="0.9" io_vdd="2.5"/>
<transistors pn_ratio="2" model_ref="M">
<nmos model_name="nch" chan_length="40e-9" min_width="140e-9"/>
<pmos model_name="pch" chan_length="40e-9" min_width="140e-9"/>
<io_nmos model_name="nch_25" chan_length="270e-9" min_width="320e-9"/>
<io_pmos model_name="pch_25" chan_length="270e-9" min_width="320e-9"/>
</transistors>
<module_circuit_models>
<circuit_model type="inv_buf" name="inv1" prefix="inv1" is_default="1">
<design_technology type="cmos" topology="inverter" size="1" tapered="off"/>
<port type="input" prefix="in" size="1"/>
<port type="output" prefix="out" size="1"/>
<delay_matrix type="rise" in_port="in" out_port="out">
10e-12
</delay_matrix>
<delay_matrix type="fall" in_port="in" out_port="out">
10e-12
</delay_matrix>
</circuit_model>
<circuit_model type="inv_buf" name="buf4" prefix="buf4" is_default="0">
<design_technology type="cmos" topology="buffer" size="1" tapered="on" tap_drive_level="2" f_per_stage="4"/>
<port type="input" prefix="in" size="1"/>
<port type="output" prefix="out" size="1"/>
</circuit_model>
<circuit_model type="inv_buf" name="tap_inv4" prefix="tap_inv4" is_default="0">
<design_technology type="cmos" topology="buffer" size="1" tapered="on" tap_drive_level="3" f_per_stage="4"/>
<port type="input" prefix="in" size="1"/>
<port type="output" prefix="out" size="1"/>
</circuit_model>
<circuit_model type="pass_gate" name="tgate" prefix="tgate" is_default="1">
<design_technology type="cmos" topology="transmission_gate" nmos_size="1" pmos_size="2"/>
<input_buffer exist="off"/>
<output_buffer exist="off"/>
<port type="input" prefix="in" size="1"/>
<port type="input" prefix="sel" size="1"/>
<port type="input" prefix="selb" size="1"/>
<port type="output" prefix="out" size="1"/>
<delay_matrix type="rise" in_port="in sel selb" out_port="out">
10e-12 0e-12 0e-12
</delay_matrix>
<delay_matrix type="fall" in_port="in sel selb" out_port="out">
10e-12 0e-12 0e-12
</delay_matrix>
</circuit_model>
<circuit_model type="gate" name="or2" prefix="or2" is_default="1" verilog_netlist="/research/ece/lnis/USERS/alacchi/clone_github/tangxifan-eda-tools/branches/vpr7_rram/vpr/VerilogNetlists/sram.v/VerilogNetlists/essential_gates.v">
<design_technology type="cmos" topology="OR"/>
<input_buffer exist="off"/>
<output_buffer exist="off"/>
<port type="input" prefix="in" size="2"/>
<port type="output" prefix="out" size="1"/>
<delay_matrix type="rise" in_port="in" out_port="out">
10e-12
</delay_matrix>
<delay_matrix type="fall" in_port="in" out_port="out">
10e-12
</delay_matrix>
</circuit_model>
<circuit_model type="chan_wire" name="chan_segment" prefix="track_seg" is_default="1">
<design_technology type="cmos"/>
<input_buffer exist="off"/>
<output_buffer exist="off"/>
<port type="input" prefix="in" size="1"/>
<port type="output" prefix="out" size="1"/>
<wire_param model_type="pie" res_val="101" cap_val="22.5e-15" level="1"/> <!-- model_type could be T, res_val and cap_val DON'T CARE -->
</circuit_model>
<circuit_model type="wire" name="direct_interc" prefix="direct_interc" is_default="1">
<design_technology type="cmos"/>
<input_buffer exist="off"/>
<output_buffer exist="off"/>
<port type="input" prefix="in" size="1"/>
<port type="output" prefix="out" size="1"/>
<wire_param model_type="pie" res_val="0" cap_val="0" level="1"/> <!-- model_type could be T, res_val cap_val should be defined -->
</circuit_model>
<circuit_model type="mux" name="mux_tree_like" prefix="mux_tree_like" dump_structural_verilog="true">
<design_technology type="cmos" structure="tree-like" add_const_input="true" const_input_val="1"/>
<input_buffer exist="on" circuit_model_name="inv1"/>
<output_buffer exist="on" circuit_model_name="inv1"/>
<!--mux2to1 subckt_name="mux2to1"/-->
<pass_gate_logic circuit_model_name="tgate"/>
<port type="input" prefix="in" size="1"/>
<port type="output" prefix="out" size="1"/>
<port type="sram" prefix="sram" size="1"/>
</circuit_model>
<circuit_model type="mux" name="mux_tree_like_tapbuf" prefix="mux_tree_like_tapbuf" dump_structural_verilog="true" is_default="0">
<design_technology type="cmos" structure="tree-like" add_const_input="true" const_input_val="1"/>
<input_buffer exist="on" circuit_model_name="inv1"/>
<output_buffer exist="on" circuit_model_name="tap_inv4"/>
<!--mux2to1 subckt_name="mux2to1"/-->
<pass_gate_logic circuit_model_name="tgate"/>
<port type="input" prefix="in" size="1"/>
<port type="output" prefix="out" size="1"/>
<port type="sram" prefix="sram" size="1"/>
</circuit_model>
<circuit_model type="mux" name="mux_1level_tapbuf" prefix="mux_1level_tapbuf" is_default="1" dump_structural_verilog="true">
<design_technology type="cmos" structure="tree-like" add_const_input="true" const_input_val="1"/>
<input_buffer exist="on" circuit_model_name="inv1"/>
<output_buffer exist="on" circuit_model_name="tap_inv4"/>
<!--mux2to1 subckt_name="mux2to1"/-->
<pass_gate_logic circuit_model_name="tgate"/>
<port type="input" prefix="in" size="1"/>
<port type="output" prefix="out" size="1"/>
<port type="sram" prefix="sram" size="1"/>
</circuit_model>
<!--DFF subckt ports should be defined as <D> <Q> <CLK> <RESET> <SET> -->
<circuit_model type="ff" name="static_dff" prefix="dff" spice_netlist="/research/ece/lnis/USERS/alacchi/Current_release/OpenFPGA/vpr7_x2p/vpr/SpiceNetlists/ff.sp" verilog_netlist="/research/ece/lnis/USERS/alacchi/Current_release/OpenFPGA/vpr7_x2p/vpr/VerilogNetlists/ff.v">
<design_technology type="cmos"/>
<input_buffer exist="on" circuit_model_name="inv1"/>
<output_buffer exist="on" circuit_model_name="inv1"/>
<pass_gate_logic circuit_model_name="tgate"/>
<port type="input" prefix="D" size="1"/>
<port type="input" prefix="Set" size="1" is_global="true" default_val="0" is_set="true"/>
<port type="input" prefix="Reset" size="1" is_global="true" default_val="1" is_reset="true"/>
<port type="output" prefix="Q" size="1"/>
<port type="clock" prefix="clk" size="1" is_global="true" default_val="0" />
</circuit_model>
<circuit_model type="lut" name="frac_lut6" prefix="frac_lut6" dump_structural_verilog="true">
<design_technology type="cmos" fracturable_lut="true"/>
<input_buffer exist="on" circuit_model_name="inv1"/>
<output_buffer exist="on" circuit_model_name="inv1"/>
<lut_input_buffer exist="on" circuit_model_name="buf4"/>
<lut_input_inverter exist="on" circuit_model_name="inv1"/>
<pass_gate_logic circuit_model_name="tgate"/>
<port type="input" prefix="in" size="6" tri_state_map="----11" circuit_model_name="or2"/>
<port type="output" prefix="lut4_out" size="4" lut_frac_level="4" lut_output_mask="0,1,2,3"/>
<port type="output" prefix="lut5_out" size="2" lut_frac_level="5" lut_output_mask="0,1"/>
<port type="output" prefix="lut6_out" size="1" lut_output_mask="0"/>
<port type="sram" prefix="sram" size="64"/>
<port type="sram" prefix="mode" size="2" mode_select="true" circuit_model_name="sc_dff_compact" default_val="1"/>
</circuit_model>
<!--Scan-chain DFF subckt ports should be defined as <D> <Q> <Qb> <CLK> <RESET> <SET> -->
<circuit_model type="sff" name="sc_dff_compact" prefix="scff" spice_netlist="/research/ece/lnis/USERS/alacchi/Current_release/OpenFPGA/vpr7_x2p/vpr/SpiceNetlists/ff.sp" verilog_netlist="/research/ece/lnis/USERS/alacchi/Current_release/OpenFPGA/vpr7_x2p/vpr/VerilogNetlists/ff.v">
<design_technology type="cmos"/>
<input_buffer exist="on" circuit_model_name="inv1"/>
<output_buffer exist="on" circuit_model_name="inv1"/>
<pass_gate_logic circuit_model_name="tgate"/>
<port type="input" prefix="pReset" size="1" is_global="true" default_val="1" is_reset="true" is_prog="true"/>
<port type="input" prefix="pSet" size="1" is_global="true" default_val="0" is_set="true" is_prog="true"/>
<port type="input" prefix="D" size="1"/>
<port type="output" prefix="Q" size="1"/>
<port type="output" prefix="Qb" size="1"/>
<port type="clock" prefix="prog_clk" size="1" is_global="true" default_val="0" is_prog="true"/>
</circuit_model>
<circuit_model type="iopad" name="iopad" prefix="iopad" spice_netlist="/research/ece/lnis/USERS/alacchi/Current_release/OpenFPGA/vpr7_x2p/vpr/SpiceNetlists/io.sp" verilog_netlist="/research/ece/lnis/USERS/alacchi/Current_release/OpenFPGA/vpr7_x2p/vpr/VerilogNetlists/io.v">
<design_technology type="cmos"/>
<input_buffer exist="on" circuit_model_name="inv1"/>
<output_buffer exist="on" circuit_model_name="inv1"/>
<pass_gate_logic circuit_model_name="tgate"/>
<port type="inout" prefix="pad" size="1"/>
<port type="sram" prefix="en" size="1" mode_select="true" circuit_model_name="sc_dff_compact" default_val="1"/>
<!--port type="sram" prefix="enb" size="1" mode_select="true" circuit_model_name="sc_dff_compact" default_val="0"/-->
<port type="input" prefix="outpad" size="1"/>
<!-- <port type="input" prefix="zin" size="1" is_global="true" default_val="0" /> -->
<port type="output" prefix="inpad" size="1"/>
</circuit_model>
<!-- Hard logic definition for heterogenous blocks -->
<circuit_model type="hard_logic" name="adder_1bit" prefix="adder" spice_netlist="/research/ece/lnis/USERS/alacchi/Current_release/OpenFPGA/vpr7_x2p/vpr/SpiceNetlists/adder.sp" verilog_netlist="/research/ece/lnis/USERS/alacchi/Current_release/OpenFPGA/vpr7_x2p/vpr/VerilogNetlists/adder.v">
<design_technology type="cmos"/>
<input_buffer exist="on" circuit_model_name="inv1"/>
<output_buffer exist="on" circuit_model_name="inv1"/>
<port type="input" prefix="a" size="1"/>
<port type="input" prefix="b" size="1"/>
<port type="input" prefix="cin" size="1"/>
<port type="output" prefix="sumout" size="1"/>
<port type="output" prefix="cout" size="1"/>
</circuit_model>
<circuit_model type="sram" name="sram6T" prefix="sram" spice_netlist="/research/ece/lnis/USERS/alacchi/Current_release/OpenFPGA/vpr7_x2p/vpr/SpiceNetlists/sram.sp" verilog_netlist="/research/ece/lnis/USERS/alacchi/Current_release/OpenFPGA/vpr7_x2p/vpr/VerilogNetlists/sram.v" >
<design_technology type="cmos"/>
<input_buffer exist="on" circuit_model_name="inv1"/>
<output_buffer exist="on" circuit_model_name="inv1"/>
<pass_gate_logic circuit_model_name="tgate"/>
<port type="input" prefix="in" size="1"/>
<port type="output" prefix="out" size="2"/>
</circuit_model>
</module_circuit_models>
</spice_settings>
<device>
<!-- VB & JL: Using Ian Kuon's transistor sizing and drive strength data for routing, at 40 nm. Ian used BPTM
models. We are modifying the delay values however, to include metal C and R, which allows more architecture
experimentation. We are also modifying the relative resistance of PMOS to be 1.8x that of NMOS
(vs. Ian's 3x) as 1.8x lines up with Jeff G's data from a 45 nm process (and is more typical of
45 nm in general). I'm upping the Rmin_nmos from Ian's just over 6k to nearly 9k, and dropping
RminW_pmos from 18k to 16k to hit this 1.8x ratio, while keeping the delays of buffers approximately
lined up with Stratix IV.
We are using Jeff G.'s capacitance data for 45 nm (in tech/ptm_45nm).
Jeff's tables list C in for transistors with widths in multiples of the minimum feature size (45 nm).
The minimum contactable transistor is 2.5 * 45 nm, so I need to multiply drive strength sizes in this file
by 2.5x when looking up in Jeff's tables.
The delay values are lined up with Stratix IV, which has an architecture similar to this
proposed FPGA, and which is also 40 nm
C_ipin_cblock: input capacitance of a track buffer, which VPR assumes is a single-stage
4x minimum drive strength buffer. -->
<sizing R_minW_nmos="8926" R_minW_pmos="16067" ipin_mux_trans_size="9"/>
<timing C_ipin_cblock="596e-18" T_ipin_cblock="77.93e-12"/>
<!-- The grid_logic_tile_area below will be used for all blocks that do not explicitly set their own (non-routing)
area; set to 0 since we explicitly set the area of all blocks currently in this architecture file.
-->
<area grid_logic_tile_area="0"/>
<sram area="6">
<verilog organization="scan-chain" circuit_model_name="sc_dff_compact"/>
<!--verilog organization="memory-bank" circuit_model_name="sram6T_blwl"/-->
<spice organization="standalone" circuit_model_name="sram6T" />
</sram>
<chan_width_distr>
<io width="1.000000"/>
<x distr="uniform" peak="1.000000"/>
<y distr="uniform" peak="1.000000"/>
</chan_width_distr>
<switch_block type="wilton" fs="3"/>
</device>
<cblocks>
<switch type="mux" name="cb_mux" R="0" Cin="596e-18" Cout="0" Tdel="77.93e-12" mux_trans_size="3" buf_size="63" circuit_model_name="mux_tree_like_tapbuf" structure="tree-like" num_level="2">
</switch>
</cblocks>
<switchlist>
<!-- VB: the mux_trans_size and buf_size data below is in minimum width transistor *areas*, assuming the purple
book area formula. This means the mux transistors are about 5x minimum drive strength.
We assume the first stage of the buffer is 3x min drive strength to be reasonable given the large
mux transistors, and this gives a reasonable stage ratio of a bit over 5x to the second stage. We assume
the n and p transistors in the first stage are equal-sized to lower the buffer trip point, since it's fed
by a pass transistor mux. We can then reverse engineer the buffer second stage to hit the specified
buf_size (really buffer area) - 16.2x minimum drive nmos and 1.8*16.2 = 29.2x minimum drive.
I then took the data from Jeff G.'s PTM modeling of 45 nm to get the Cin (gate of first stage) and Cout
(diff of second stage) listed below. Jeff's models are in tech/ptm_45nm, and are in min feature multiples.
The minimum contactable transistor is 2.5 * 45 nm, so I need to multiply the drive strength sizes above by
2.5x when looking up in Jeff's tables.
Finally, we choose a switch delay (58 ps) that leads to length 4 wires having a delay equal to that of SIV of 126 ps.
This also leads to the switch being 46% of the total wire delay, which is reasonable. -->
<switch type="mux" name="sb_mux_L4" R="105" Cin="596e-18" Cout="0e-15" Tdel="47.2e-12" mux_trans_size="3" buf_size="63" circuit_model_name="mux_tree_like_tapbuf" structure="tree-like" num_level="1">
</switch>
<switch type="mux" name="sb_mux_L2" R="115" Cin="596e-18" Cout="0e-15" Tdel="47.2e-12" mux_trans_size="3" buf_size="63" circuit_model_name="mux_tree_like_tapbuf" structure="tree-like" num_level="1">
</switch>
<switch type="mux" name="sb_mux_L1" R="128" Cin="596e-18" Cout="0e-15" Tdel="47.2e-12" mux_trans_size="3" buf_size="63" circuit_model_name="mux_tree_like_tapbuf" structure="tree-like" num_level="1">
</switch>
</switchlist>
<segmentlist>
<!--- VB & JL: using ITRS metal stack data, 96 nm half pitch wires, which are intermediate metal width/space.
With the 96 nm half pitch, such wires would take 60 um of height, vs. a 90 nm high (approximated as square) Stratix IV tile so this seems
reasonable. Using a tile length of 90 nm, corresponding to the length of a Stratix IV tile if it were square. -->
<segment freq="0.4" length="4" type="unidir" Rmetal="101" Cmetal="22.5e-15" circuit_model_name="chan_segment">
<mux name="sb_mux_L4"/>
<sb type="pattern">1 1 1 1 1</sb>
<cb type="pattern">1 1 1 1</cb>
</segment>
<segment freq="0.3" length="2" type="unidir" Rmetal="101" Cmetal="22.5e-15" circuit_model_name="chan_segment">
<mux name="sb_mux_L4"/>
<sb type="pattern">1 1 1</sb>
<cb type="pattern">1 1 </cb>
</segment>
<segment freq="0.3" length="1" type="unidir" Rmetal="101" Cmetal="22.5e-15" circuit_model_name="chan_segment">
<mux name="sb_mux_L4"/>
<sb type="pattern">1 1</sb>
<cb type="pattern">1</cb>
</segment>
</segmentlist>
<!--switch_segment_patterns>
<pattern type="unbuf_sb" seg_length="1" seg_type="unidir" pattern_length="2">
<unbuf_mux name="1"/>
<sb type ="pattern">0 1</sb>
</pattern>
</switch_segment_patterns-->
<complexblocklist>
<!-- Define I/O pads begin -->
<!-- Capacity is a unique property of I/Os, it is the maximum number of I/Os that can be placed at the same (X,Y) location on the FPGA -->
<!-- Not sure of the area of an I/O (varies widely), and it's not relevant to the design of the FPGA core, so we're setting it to 0. -->
<pb_type name="io" capacity="7" area="0" idle_mode_name="inpad" physical_mode_name="io_phy">
<input name="outpad" num_pins="1"/>
<output name="inpad" num_pins="1"/>
<!-- physical design description -->
<mode name="io_phy" disabled_in_packing="true">
<pb_type name="iopad" blif_model=".subckt io" num_pb="1" circuit_model_name="iopad" mode_bits="1">
<input name="outpad" num_pins="1"/>
<output name="inpad" num_pins="1"/>
</pb_type>
<interconnect>
<direct name="inpad" input="iopad.inpad" output="io.inpad">
<delay_constant max="0e-11" in_port="iopad.inpad" out_port="io.inpad"/>
</direct>
<direct name="outpad" input="io.outpad" output="iopad.outpad">
<delay_constant max="0e-11" in_port="io.outpad" out_port="iopad.outpad"/>
</direct>
</interconnect>
</mode>
<!-- IOs can operate as either inputs or outputs.§
Delays below come from Ian Kuon. They are small, so they should be interpreted as
the delays to and from registers in the I/O (and generally I/Os are registered
today and that is when you timing analyze them.
-->
<mode name="inpad">
<pb_type name="inpad" blif_model=".input" num_pb="1" physical_pb_type_name="iopad" mode_bits="1">
<output name="inpad" num_pins="1" physical_mode_pin="inpad"/>
</pb_type>
<interconnect>
<direct name="inpad" input="inpad.inpad" output="io.inpad">
<delay_constant max="0e-11" in_port="inpad.inpad" out_port="io.inpad"/>
</direct>
</interconnect>
</mode>
<mode name="outpad">
<pb_type name="outpad" blif_model=".output" num_pb="1" physical_pb_type_name="iopad" mode_bits="0">
<input name="outpad" num_pins="1" physical_mode_pin="outpad"/>
</pb_type>
<interconnect>
<direct name="outpad" input="io.outpad" output="outpad.outpad">
<delay_constant max="0e-11" in_port="io.outpad" out_port="outpad.outpad"/>
</direct>
</interconnect>
</mode>
<!-- Every input pin is driven by 15% of the tracks in a channel, every output pin is driven by 10% of the tracks in a channel -->
<fc default_in_type="frac" default_in_val="0.15" default_out_type="frac" default_out_val="0.10"/>
<!-- IOs go on the periphery of the FPGA, for consistency,
make it physically equivalent on all sides so that only one definition of I/Os is needed.
If I do not make a physically equivalent definition, then I need to define 4 different I/Os, one for each side of the FPGA
-->
<pinlocations pattern="custom">
<loc side="left">io.outpad io.inpad</loc>
<loc side="top">io.outpad io.inpad</loc>
<loc side="right">io.outpad io.inpad</loc>
<loc side="bottom">io.outpad io.inpad</loc>
</pinlocations>
<!-- Place I/Os on the sides of the FPGA -->
<gridlocations>
<loc type="perimeter" priority="10"/>
</gridlocations>
<power method="ignore"/>
</pb_type>
<!-- Define I/O pads ends -->
<!-- Define general purpose logic block (CLB) begin -->
<!--- Area calculation: Total Stratix IV tile area is about 8100 um^2, and a minimum width transistor
area is 60 L^2 yields a tile area of 84375 MWTAs.
Routing at W=300 is 30481 MWTAs, leaving us with a total of 53000 MWTAs for logic block area
This means that only 37% of our area is in the general routing, and 63% is inside the logic
block. Note that the crossbar / local interconnect is considered part of the logic block
area in this analysis. That is a lower proportion of of routing area than most academics
assume, but note that the total routing area really includes the crossbar, which would push
routing area up significantly, we estimate into the ~70% range.
-->
<pb_type name="clb" area="53894">
<input name="I" num_pins="40" equivalent="true"/>
<input name="cin" num_pins="1"/>
<output name="O" num_pins="20" equivalent="false"/>
<output name="cout" num_pins="1"/>
<clock name="clk" num_pins="1"/>
<!-- Describe fracturable logic element.
Each fracturable logic element has a 6-LUT that can alternatively operate as two 5-LUTs with shared inputs.
The outputs of the fracturable logic element can be optionally registered
-->
<pb_type name="fle" num_pb="10" physical_mode_name="fle_phy" idle_mode_name="n2_lut5">
<input name="in" num_pins="6"/>
<input name="cin" num_pins="1"/>
<output name="out" num_pins="2"/>
<output name="cout" num_pins="1"/>
<clock name="clk" num_pins="1"/>
<mode name="fle_phy" disabled_in_packing="true">
<pb_type name="frac_logic" num_pb="1">
<input name="in" num_pins="6"/>
<input name="cin" num_pins="1"/>
<output name="out" num_pins="2"/>
<output name="cout" num_pins="1"/>
<pb_type name="frac_lut6" blif_model=".frac_lut6" mode_bits="11" num_pb="1" circuit_model_name="frac_lut6">
<input name="in" num_pins="6"/>
<output name="lut4_out" num_pins="4"/>
<output name="lut5_out" num_pins="2"/>
<output name="lut6_out" num_pins="1"/>
</pb_type>
<pb_type name="adder_phy" blif_model=".subckt adder" num_pb="2" circuit_model_name="adder_1bit">
<input name="a" num_pins="1"/>
<input name="b" num_pins="1"/>
<input name="cin" num_pins="1"/>
<output name="cout" num_pins="1"/>
<output name="sumout" num_pins="1"/>
</pb_type>
<interconnect>
<direct name="direct_fraclut_in" input="frac_logic.in[5:0]" output="frac_lut6.in[5:0]"/>
<direct name="direct_cin" input="frac_logic.cin" output="adder_phy[0].cin"/>
<direct name="direct_carry" input="adder_phy[0].cout" output="adder_phy[1].cin"/>
<direct name="direct_cout" input="adder_phy[1].cout" output="frac_logic.cout"/>
<direct name="direct_lut4carry0" input="frac_lut6.lut4_out[0]" output="adder_phy[0].a"/>
<direct name="direct_lut4carry1" input="frac_lut6.lut4_out[1]" output="adder_phy[0].b"/>
<direct name="direct_lut4carry2" input="frac_lut6.lut4_out[2]" output="adder_phy[1].a"/>
<direct name="direct_lut4carry3" input="frac_lut6.lut4_out[3]" output="adder_phy[1].b"/>
<mux name="mux1" input="adder_phy[0].sumout frac_lut6.lut5_out[0]" output="frac_logic.out[0]">
<mode_select mode_name="n2_lut5.arithmetic" in_port="adder_phy[0].sumout" out_port="frac_logic.out[0]"/>
<mode_select mode_name="n2_lut5.blut5" in_port="frac_lut6.lut5_out[0]" out_port="frac_logic.out[0]"/>
<mode_select mode_name="n1_lut6" in_port="frac_lut6.lut5_out[0]" out_port="frac_logic.out[0]"/>
</mux>
<mux name="mux2" input="adder_phy[1].sumout frac_lut6.lut5_out[1] frac_lut6.lut6_out[0]" output="frac_logic.out[1]">
<mode_select mode_name="n2_lut5.arithmetic" in_port="adder_phy[1].sumout" out_port="frac_logic.out[1]"/>
<mode_select mode_name="n2_lut5.blut5" in_port="frac_lut6.lut5_out[1]" out_port="frac_logic.out[1]"/>
<mode_select mode_name="n1_lut6" in_port="frac_lut6.lut6_out[0]" out_port="frac_logic.out[1]"/>
</mux>
</interconnect>
</pb_type>
<pb_type name="ff_phy" blif_model=".latch" num_pb="2" class="flipflop" circuit_model_name="static_dff">
<input name="D" num_pins="1" port_class="D"/>
<output name="Q" num_pins="1" port_class="Q"/>
<clock name="clk" num_pins="1" port_class="clock"/>
<T_setup value="66e-12" port="ff_phy.D" clock="clk"/>
<T_clock_to_Q max="124e-12" port="ff_phy.Q" clock="clk"/>
</pb_type>
<interconnect>
<complete name="direct_clk" input="fle.clk" output="ff_phy[1:0].clk"/>
<direct name="direct_in" input="fle.in[5:0]" output="frac_logic.in[5:0]"/>
<direct name="direct_cin" input="fle.cin" output="frac_logic.cin"/>
<direct name="direct_cout" input="frac_logic.cout" output="fle.cout"/>
<direct name="direct_frac_out1" input="frac_logic.out[0]" output="ff_phy[0].D"/>
<direct name="direct_frac_out2" input="frac_logic.out[1]" output="ff_phy[1].D"/>
<mux name="mux1" input="ff_phy[0].Q frac_logic.out[0]" output="fle.out[0]">
</mux>
<mux name="mux2" input="ff_phy[1].Q frac_logic.out[1]" output="fle.out[1]">
</mux>
</interconnect>
</mode>
<mode name="n2_lut5" disabled_in_packing="false">
<!-- multi-mode support -->
<pb_type name="lut5inter" num_pb="1">
<input name="in" num_pins="5"/>
<input name="cin" num_pins="1"/>
<output name="out" num_pins="2"/>
<output name="cout" num_pins="1"/>
<clock name="clk" num_pins="1"/>
<pb_type name="ble5" num_pb="2" idle_mode_name="blut5">
<input name="in" num_pins="5"/>
<input name="cin" num_pins="1"/>
<output name="out" num_pins="1"/>
<output name="cout" num_pins="1"/>
<clock name="clk" num_pins="1"/>
<mode name="blut5">
<pb_type name="flut5" num_pb="1">
<input name="in" num_pins="5"/>
<output name="out" num_pins="1"/>
<clock name="clk" num_pins="1"/>
<!-- Regular LUT mode -->
<pb_type name="lut5" blif_model=".names" num_pb="1" class="lut" mode_bits="01" physical_pb_type_name="frac_lut6" physical_pb_type_index_factor="0.5">
<input name="in" num_pins="5" port_class="lut_in" physical_mode_pin="in[5:0]"/>
<output name="out" num_pins="1" port_class="lut_out" physical_mode_pin="lut5_out" physical_mode_pin_rotate_offset="1"/>
<!-- LUT timing using delay matrix -->
<!-- These are the physical delay inputs on a Stratix IV LUT but because VPR cannot do LUT rebalancing,
we instead take the average of these numbers to get more stable results
82e-12
173e-12
261e-12
263e-12
398e-12
-->
<delay_matrix type="max" in_port="lut5.in" out_port="lut5.out">
235e-12
235e-12
235e-12
235e-12
235e-12
</delay_matrix>
</pb_type>
<pb_type name="ff" blif_model=".latch" num_pb="1" class="flipflop" physical_pb_type_name="ff_phy">
<input name="D" num_pins="1" port_class="D" physical_mode_pin="D"/>
<output name="Q" num_pins="1" port_class="Q" physical_mode_pin="Q"/>
<clock name="clk" num_pins="1" port_class="clock" physical_mode_pin="clk"/>
<T_setup value="66e-12" port="ff.D" clock="clk"/>
<T_clock_to_Q max="124e-12" port="ff.Q" clock="clk"/>
</pb_type>
<interconnect>
<direct name="direct1" input="flut5.in" output="lut5.in"/>
<direct name="direct2" input="lut5.out" output="ff.D">
<pack_pattern name="ble5" in_port="lut5.out" out_port="ff.D"/>
</direct>
<direct name="direct3" input="flut5.clk" output="ff.clk"/>
<mux name="mux1" input="ff.Q lut5.out" output="flut5.out" spice_model_sram_offset="0">
<delay_constant max="25e-12" in_port="lut5.out" out_port="flut5.out" />
<delay_constant max="45e-12" in_port="ff.Q" out_port="flut5.out" />
</mux>
</interconnect>
</pb_type>
<interconnect>
<direct name="direct1" input="ble5.in" output="flut5.in"/>
<direct name="direct2" input="ble5.clk" output="flut5.clk"/>
<direct name="direct3" input="flut5.out" output="ble5.out"/>
</interconnect>
</mode>
<mode name="arithmetic">
<pb_type name="arithmetic" num_pb="1">
<input name="in" num_pins="4"/>
<input name="cin" num_pins="1"/>
<output name="out" num_pins="1"/>
<output name="cout" num_pins="1"/>
<clock name="clk" num_pins="1"/>
<!-- Special dual-LUT mode that drives adder only -->
<pb_type name="lut4" blif_model=".names" num_pb="2" class="lut" mode_bits="11" physical_pb_type_name="frac_lut6" physical_pb_type_index_factor="0.25">
<input name="in" num_pins="4" port_class="lut_in" physical_mode_pin="in[4:0]"/>
<output name="out" num_pins="1" port_class="lut_out" physical_mode_pin="lut4_out" physical_mode_pin_rotate_offset="1"/>
<!-- LUT timing using delay matrix -->
<!-- These are the physical delay inputs on a Stratix IV LUT but because VPR cannot do LUT rebalancing,
we instead take the average of these numbers to get more stable results
82e-12
173e-12
261e-12
263e-12
-->
<delay_matrix type="max" in_port="lut4.in" out_port="lut4.out">
195e-12
195e-12
195e-12
195e-12
</delay_matrix>
</pb_type>
<pb_type name="adder" blif_model=".subckt adder" num_pb="1" physical_pb_type_name="adder_phy">
<input name="a" num_pins="1" physical_mode_pin="a"/>
<input name="b" num_pins="1" physical_mode_pin="b"/>
<input name="cin" num_pins="1" physical_mode_pin="cin"/>
<output name="cout" num_pins="1" physical_mode_pin="cout"/>
<output name="sumout" num_pins="1" physical_mode_pin="sumout"/>
<delay_constant max="0.3e-9" in_port="adder.a" out_port="adder.sumout"/>
<delay_constant max="0.3e-9" in_port="adder.b" out_port="adder.sumout"/>
<delay_constant max="0.3e-9" in_port="adder.cin" out_port="adder.sumout"/>
<delay_constant max="0.3e-9" in_port="adder.a" out_port="adder.cout"/>
<delay_constant max="0.3e-9" in_port="adder.b" out_port="adder.cout"/>
<delay_constant max="0.01e-9" in_port="adder.cin" out_port="adder.cout"/>
</pb_type>
<pb_type name="ff" blif_model=".latch" num_pb="1" class="flipflop" physical_pb_type_name="ff_phy">
<input name="D" num_pins="1" port_class="D" physical_mode_pin="D"/>
<output name="Q" num_pins="1" port_class="Q" physical_mode_pin="Q"/>
<clock name="clk" num_pins="1" port_class="clock" physical_mode_pin="clk"/>
<T_setup value="66e-12" port="ff.D" clock="clk"/>
<T_clock_to_Q max="124e-12" port="ff.Q" clock="clk"/>
</pb_type>
<interconnect>
<direct name="clock" input="arithmetic.clk" output="ff.clk"/>
<direct name="lut_in1" input="arithmetic.in[3:0]" output="lut4[0:0].in[3:0]"/>
<direct name="lut_in2" input="arithmetic.in[3:0]" output="lut4[1:1].in[3:0]"/>
<direct name="lut_to_add1" input="lut4[0:0].out" output="adder.a">
</direct>
<direct name="lut_to_add2" input="lut4[1:1].out" output="adder.b">
</direct>
<direct name="add_to_ff" input="adder.sumout" output="ff.D">
<pack_pattern name="chain" in_port="adder.sumout" out_port="ff.D"/>
</direct>
<direct name="carry_in" input="arithmetic.cin" output="adder.cin">
<pack_pattern name="chain" in_port="arithmetic.cin" out_port="adder.cin"/>
</direct>
<direct name="carry_out" input="adder.cout" output="arithmetic.cout">
<pack_pattern name="chain" in_port="adder.cout" out_port="arithmetic.cout"/>
</direct>
<mux name="sumout" input="ff.Q adder.sumout" output="arithmetic.out">
<delay_constant max="25e-12" in_port="adder.sumout" out_port="arithmetic.out"/>
<delay_constant max="45e-12" in_port="ff.Q" out_port="arithmetic.out" />
</mux>
</interconnect>
</pb_type>
<interconnect>
<direct name="direct1" input="ble5.in[3:0]" output="arithmetic.in"/>
<direct name="carry_in" input="ble5.cin" output="arithmetic.cin">
<pack_pattern name="chain" in_port="ble5.cin" out_port="arithmetic.cin"/>
</direct>
<direct name="carry_out" input="arithmetic.cout" output="ble5.cout">
<pack_pattern name="chain" in_port="arithmetic.cout" out_port="ble5.cout"/>
</direct>
<direct name="direct2" input="ble5.clk" output="arithmetic.clk"/>
<direct name="direct3" input="arithmetic.out" output="ble5.out"/>
</interconnect>
</mode>
</pb_type>
<interconnect>
<direct name="direct1" input="lut5inter.in" output="ble5[0:0].in"/>
<direct name="direct2" input="lut5inter.in" output="ble5[1:1].in"/>
<direct name="direct3" input="ble5[1:0].out" output="lut5inter.out"/>
<direct name="carry_in" input="lut5inter.cin" output="ble5[0:0].cin">
<pack_pattern name="chain" in_port="lut5inter.cin" out_port="ble5[0:0].cin"/>
</direct>
<direct name="carry_out" input="ble5[1:1].cout" output="lut5inter.cout">
<pack_pattern name="chain" in_port="ble5[1:1].cout" out_port="lut5inter.cout"/>
</direct>
<direct name="carry_link" input="ble5[0:0].cout" output="ble5[1:1].cin">
<pack_pattern name="chain" in_port="ble5[0:0].cout" out_port="ble5[1:1].cout"/>
</direct>
<complete name="complete1" input="lut5inter.clk" output="ble5[1:0].clk"/>
</interconnect>
</pb_type>
<interconnect>
<direct name="direct1" input="fle.in[4:0]" output="lut5inter.in"/>
<direct name="direct2" input="lut5inter.out" output="fle.out"/>
<direct name="direct3" input="fle.clk" output="lut5inter.clk"/>
<direct name="carry_in" input="fle.cin" output="lut5inter.cin">
<pack_pattern name="chain" in_port="fle.cin" out_port="lut5inter.cin"/>
</direct>
<direct name="carry_out" input="lut5inter.cout" output="fle.cout">
<pack_pattern name="chain" in_port="lut5inter.cout" out_port="fle.cout"/>
</direct>
</interconnect>
</mode> <!-- n2_lut5 -->
<mode name="n1_lut6">
<pb_type name="ble6" num_pb="1">
<input name="in" num_pins="6"/>
<output name="out" num_pins="1"/>
<clock name="clk" num_pins="1"/>
<pb_type name="lut6" blif_model=".names" num_pb="1" class="lut" mode_bits="00" physical_pb_type_name="frac_lut6" spice_model_sram_offset="0">
<input name="in" num_pins="6" port_class="lut_in" physical_mode_pin="in[5:0]"/>
<output name="out" num_pins="1" port_class="lut_out" physical_mode_pin="lut6_out[0]"/>
<!-- LUT timing using delay matrix -->
<!-- These are the physical delay inputs on a Stratix IV LUT but because VPR cannot do LUT rebalancing,
we instead take the average of these numbers to get more stable results
82e-12
173e-12
261e-12
263e-12
398e-12
397e-12
-->
<delay_matrix type="max" in_port="lut6.in" out_port="lut6.out">
261e-12
261e-12
261e-12
261e-12
261e-12
261e-12
</delay_matrix>
</pb_type>
<pb_type name="ff" blif_model=".latch" num_pb="1" class="flipflop" physical_pb_type_name="ff_phy" physical_pb_type_index_factor="2" physical_pb_type_index_offset="1">
<input name="D" num_pins="1" port_class="D" physical_mode_pin="D"/>
<output name="Q" num_pins="1" port_class="Q" physical_mode_pin="Q"/>
<clock name="clk" num_pins="1" port_class="clock" physical_mode_pin="clk"/>
<T_setup value="66e-12" port="ff.D" clock="clk"/>
<T_clock_to_Q max="124e-12" port="ff.Q" clock="clk"/>
</pb_type>
<interconnect>
<direct name="direct1" input="ble6.in" output="lut6[0:0].in"/>
<direct name="direct2" input="lut6.out" output="ff.D">
<pack_pattern name="ble6" in_port="lut6.out" out_port="ff.D"/>
</direct>
<direct name="direct3" input="ble6.clk" output="ff.clk"/>
<mux name="mux1" input="ff.Q lut6.out" output="ble6.out">
<delay_constant max="25e-12" in_port="lut6.out" out_port="ble6.out" />
<delay_constant max="45e-12" in_port="ff.Q" out_port="ble6.out" />
</mux>
</interconnect>
</pb_type>
<interconnect>
<direct name="direct1" input="fle.in" output="ble6.in"/>
<direct name="direct2" input="ble6.out" output="fle.out[1:1]"/>
<direct name="direct3" input="fle.clk" output="ble6.clk"/>
</interconnect>
</mode> <!-- n1_lut6 -->
</pb_type>
<interconnect>
<!-- We use a full crossbar to get logical equivalence at inputs of CLB
The delays below come from Stratix IV. the delay through a connection block
input mux + the crossbar in Stratix IV is 167 ps. We already have a 72 ps
delay on the connection block input mux (modeled by Ian Kuon), so the remaining
delay within the crossbar is 95 ps.
The delays of cluster feedbacks in Stratix IV is 100 ps, when driven by a LUT.
Since all our outputs LUT outputs go to a BLE output, and have a delay of
25 ps to do so, we subtract 25 ps from the 100 ps delay of a feedback
to get the part that should be marked on the crossbar. -->
<complete name="crossbar" input="clb.I fle[9:0].out" output="fle[9:0].in" circuit_model_name="mux_tree_like">
<delay_constant max="95e-12" in_port="clb.I" out_port="fle[9:0].in" />
<delay_constant max="75e-12" in_port="fle[9:0].out" out_port="fle[9:0].in" />
</complete>
<complete name="clks" input="clb.clk" output="fle[9:0].clk">
</complete>
<!-- This way of specifying direct connection to clb outputs is important because this architecture uses automatic spreading of opins.
By grouping to output pins in this fashion, if a logic block is completely filled by 6-LUTs,
then the outputs those 6-LUTs take get evenly distributed across all four sides of the CLB instead of clumped on two sides (which is what happens with a more
naive specification).
-->
<direct name="clbouts1" input="fle[9:0].out[0:0]" output="clb.O[9:0]"/>
<direct name="clbouts2" input="fle[9:0].out[1:1]" output="clb.O[19:10]"/>
<!-- Carry chain links -->
<direct name="carry_in" input="clb.cin" output="fle[0:0].cin">
<!-- Put all inter-block carry chain delay on this one edge -->
<delay_constant max="0.16e-9" in_port="clb.cin" out_port="fle[0:0].cin"/>
<pack_pattern name="chain" in_port="clb.cin" out_port="fle[0:0].cin"/>
</direct>
<direct name="carry_out" input="fle[9:9].cout" output="clb.cout">
<pack_pattern name="chain" in_port="fle[9:9].cout" out_port="clb.cout"/>
</direct>
<direct name="carry_link" input="fle[8:0].cout" output="fle[9:1].cin">
<pack_pattern name="chain" in_port="fle[8:0].cout" out_port="fle[9:1].cin"/>
</direct>
</interconnect>
<fc default_in_type="frac" default_in_val="0.15" default_out_type="frac" default_out_val="0.10">
<pin name="cin" fc_type="frac" fc_val="0"/>
<pin name="cout" fc_type="frac" fc_val="0"/>
</fc>
<pinlocations pattern="spread"/>
<gridlocations>
<loc type="fill" priority="1"/>
</gridlocations>
</pb_type>
<!-- Define general purpose logic block (CLB) ends -->
</complexblocklist>
<power>
<local_interconnect C_wire="2.5e-10"/>
<mux_transistor_size mux_transistor_size="3"/>
<FF_size FF_size="4"/>
<LUT_transistor_size LUT_transistor_size="4"/>
</power>
<clocks>
<clock buffer_size="auto" C_wire="2.5e-10"/>
</clocks>
</architecture>

1452
vpr7_x2p/vpr/ARCH/k6_N10_sram_tsmc40nm_TT.xml Normal file
View File

File diff suppressed because it is too large Load Diff

10
vpr7_x2p/vpr/SRC/fpga_spice/verilog/verilog_api.c
View File

@ -262,10 +262,12 @@ void vpr_dump_syn_verilog(t_vpr_setup vpr_setup,
/* Output Modelsim Autodeck scripts */
if (TRUE == vpr_setup.FPGA_SPICE_Opts.SynVerilogOpts.print_modelsim_autodeck) {
dump_verilog_modelsim_autodeck(sram_verilog_orgz_info, *(Arch.spice), num_clocks,
verilog_dir_formatted, chomped_circuit_name,
vpr_setup.FPGA_SPICE_Opts.SynVerilogOpts.modelsim_ini_path,
vpr_setup.FPGA_SPICE_Opts.SynVerilogOpts.include_timing,
vpr_setup.FPGA_SPICE_Opts.SynVerilogOpts.init_sim);
verilog_dir_formatted, chomped_circuit_name,
vpr_setup.FPGA_SPICE_Opts.SynVerilogOpts.modelsim_ini_path,
vpr_setup.FPGA_SPICE_Opts.SynVerilogOpts.include_timing,
vpr_setup.FPGA_SPICE_Opts.SynVerilogOpts.init_sim,
vpr_setup.FPGA_SPICE_Opts.SynVerilogOpts.print_top_tb,
vpr_setup.FPGA_SPICE_Opts.SynVerilogOpts.print_top_auto_tb);
}
/* dump verilog testbench only for input blif */

1
vpr7_x2p/vpr/SRC/fpga_spice/verilog/verilog_global.c
View File

@ -23,6 +23,7 @@ char* modelsim_project_name_postfix = "_fpga_msim";
char* modelsim_proc_script_name_postfix = "_proc.tcl";
char* modelsim_top_script_name_postfix = "_runsim.tcl";
char* modelsim_testbench_module_postfix = "_top_tb";
char* modelsim_auto_testbench_module_postfix = "_top_auto_tb";
char* modelsim_simulation_time_unit = "ms";
char* verilog_top_postfix = "_top.v";

1
vpr7_x2p/vpr/SRC/fpga_spice/verilog/verilog_global.h
View File

@ -15,6 +15,7 @@ extern char* modelsim_project_name_postfix;
extern char* modelsim_proc_script_name_postfix;
extern char* modelsim_top_script_name_postfix;
extern char* modelsim_testbench_module_postfix;
extern char* modelsim_auto_testbench_module_postfix;
extern char* modelsim_simulation_time_unit;
extern char* verilog_top_postfix;

234
vpr7_x2p/vpr/SRC/fpga_spice/verilog/verilog_modelsim_autodeck.c
View File

@ -230,6 +230,138 @@ void dump_verilog_modelsim_proc_script(char* modelsim_proc_filename,
return;
}
void dump_verilog_modelsim_proc_auto_script(char* modelsim_proc_filename,
char* modelsim_ini_path,
char* circuit_name,
boolean include_timing,
boolean init_sim,
char* modelsim_project_name) {
FILE* fp = NULL;
char* circuit_top_tb_name = NULL;
circuit_top_tb_name = my_strcat(circuit_name, modelsim_auto_testbench_module_postfix);
/* Create Modelsim proc file */
/* Open file and file handler */
fp = fopen(modelsim_proc_filename, "w");
if (NULL == fp) {
vpr_printf(TIO_MESSAGE_ERROR,"(FILE:%s,LINE[%d])Failure in create Modelsim simulation deck auto-generation scripts: %s",
__FILE__, __LINE__, modelsim_proc_filename);
exit(1);
}
fprintf(fp, "proc create_project {projectname project_path} {\n");
fprintf(fp, " #Switch to the modelsim folder to create the project\n");
fprintf(fp, " set libname $projectname\n");
fprintf(fp, " set initfile %s\n", modelsim_ini_path);
fprintf(fp, " project new $project_path/$projectname $projectname $libname $initfile 0\n");
fprintf(fp, "}\n");
fprintf(fp, " \n");
fprintf(fp, "proc create_project_with_close {projectname modelsim_path} {\n");
fprintf(fp, " #Get the current project name\n");
fprintf(fp, " set project_env [project env]\n");
fprintf(fp, " if {$project_env eq \"\"} {\n");
fprintf(fp, " #If string empty (no project)\n");
fprintf(fp, " create_project $projectname $modelsim_path\n");
fprintf(fp, " } else {\n");
fprintf(fp, " #If string not empty (a project is loaded so clsoe it first)\n");
fprintf(fp, " project close\n");
fprintf(fp, " create_project $projectname $modelsim_path\n");
fprintf(fp, " }\n");
fprintf(fp, " }\n");
fprintf(fp, " \n");
fprintf(fp, "proc add_files_project {verilog_files} {\n");
fprintf(fp, " #Get the length of the list\n");
fprintf(fp, " set listlength [llength $verilog_files]\n");
fprintf(fp, " #Add the verilog files one by one\n");
fprintf(fp, " for {set x 0} {$x<$listlength} {incr x} {\n");
fprintf(fp, " project addfile [lindex $verilog_files $x]\n");
fprintf(fp, " }\n");
fprintf(fp, "}\n");
fprintf(fp, " \n");
fprintf(fp, "proc add_waves {} {\n");
fprintf(fp, " add wave -position insertpoint sim:/%s/*\n", circuit_top_tb_name);
fprintf(fp, "}\n");
fprintf(fp, "proc runsim {simtime unit} {\n");
fprintf(fp, " run $simtime $unit\n");
fprintf(fp, "}\n");
fprintf(fp, "#Top procedure to create enw project\n");
fprintf(fp, "proc top_create_new_project {projectname verilog_files modelsim_path simtime unit} {\n");
fprintf(fp, " #Create the project\n");
fprintf(fp, " create_project_with_close $projectname $modelsim_path\n");
fprintf(fp, " #Add the verilog files\n");
fprintf(fp, " add_files_project $verilog_files\n");
fprintf(fp, " #Compile all the files\n");
// fprintf(fp, " project compileall\n"); // removed to allow compilation with define
// Begin of compilation with Define
fprintf(fp, " set myFiles [project filenames]\n");
fprintf(fp, " foreach x $myFiles {\n");
fprintf(fp, " vlog ");
if(TRUE == include_timing){
fprintf(fp, "+define+%s ", verilog_timing_preproc_flag);
}
if(TRUE == init_sim){
fprintf(fp, "+define+%s ", verilog_init_sim_preproc_flag);
}
fprintf(fp, "$x\n }\n");
// End of compilation with Define
fprintf(fp, " #Start the simulation\n");
fprintf(fp, " vsim $projectname.%s -voptargs=+acc\n", circuit_top_tb_name);
fprintf(fp, " #Add the waves \n");
fprintf(fp, " add_waves\n");
fprintf(fp, " #run the simulation\n");
fprintf(fp, " runsim $simtime $unit\n");
fprintf(fp, " #Fit the window view\n");
fprintf(fp, " wave zoom full\n");
fprintf(fp, "}\n");
fprintf(fp, "#Top proc to recompile files and re run the simulation\n");
fprintf(fp, "proc top_rerun_sim {simtime unit} {\n");
// Save format
fprintf(fp, " #Save actual format\n");
fprintf(fp, " set myLoc [pwd]\n");
fprintf(fp, " write format wave -window .main_pane.wave.interior.cs.body.pw.wf $myLoc/relaunch.do\n");
// Quit simulation
fprintf(fp, " quit -sim\n");
// Recompile file
fprintf(fp, " #Compile updated verilog files\n");
fprintf(fp, " set myFiles [project filenames]\n");
fprintf(fp, " foreach x $myFiles {\n");
fprintf(fp, " vlog ");
if(TRUE == include_timing){
fprintf(fp, "+define+%s ", verilog_timing_preproc_flag);
}
if(TRUE == init_sim){
fprintf(fp, "+define+%s ", verilog_init_sim_preproc_flag);
}
fprintf(fp, "$x\n }\n");
// Restart the Simulation
fprintf(fp, " set projectname %s\n", modelsim_project_name);
fprintf(fp, " vsim $projectname.%s -voptargs=+acc -do relaunch.do\n", circuit_top_tb_name);
// Relaunch the Simulation
fprintf(fp, " #run the simulation\n");
fprintf(fp, " run $simtime $unit\n");
fprintf(fp, "}\n");
/* Close File handler */
fclose(fp);
/* Free */
my_free(circuit_top_tb_name);
return;
}
void dump_verilog_modelsim_top_script(char* modelsim_top_script_filename,
char* modelsim_proc_script_filename,
char* modelsim_project_path,
@ -299,6 +431,75 @@ void dump_verilog_modelsim_top_script(char* modelsim_top_script_filename,
return;
}
void dump_verilog_modelsim_top_auto_script(char* modelsim_top_auto_script_filename,
char* modelsim_proc_auto_script_filename,
char* modelsim_project_path,
char* circuit_name,
char* modelsim_project_name,
float sim_time,
char* sim_time_unit,
t_spice spice) {
FILE* fp = NULL;
/* Create Modelsim proc file */
/* Open file and file handler */
fp = fopen(modelsim_top_auto_script_filename, "w");
if (NULL == fp) {
vpr_printf(TIO_MESSAGE_ERROR,"(FILE:%s,LINE[%d])Failure in create Modelsim simulation deck auto-generation scripts: %s",
__FILE__, __LINE__, modelsim_top_auto_script_filename);
exit(1);
}
fprintf(fp, "set projectname %s\n", modelsim_project_name);
fprintf(fp, "set benchmark %s\n", circuit_name);
fprintf(fp, "\n");
fprintf(fp, "#in ms\n");
fprintf(fp, "set simtime %.4g\n", sim_time);
fprintf(fp, "set unit %s\n",
sim_time_unit);
fprintf(fp, "\n");
fprintf(fp, "#Path were both tcl script are located\n");
fprintf(fp, "set project_path \"%s%s\"\n", modelsim_project_path, default_modelsim_dir_name);
fprintf(fp, "\n");
fprintf(fp, "#Path were the verilog files are located\n");
fprintf(fp, "set verilog_path \"%s\"\n", modelsim_project_path);
fprintf(fp, "set verilog_files [list \\\n");
/* TODO: include verilog files */
fprintf(fp, " ${verilog_path}${benchmark}%s \\\n",
verilog_top_postfix);
fprintf(fp, " ${verilog_path}${benchmark}%s \\\n",
top_auto_testbench_verilog_file_postfix);
/* User-defined verilog netlists */
init_include_user_defined_verilog_netlists(spice);
modelsim_include_user_defined_verilog_netlists(fp, spice);
fprintf(fp, " ${verilog_path}%s%s \\\n",
default_lb_dir_name, logic_block_verilog_file_name);
fprintf(fp, " ${verilog_path}%s%s \\\n",
default_rr_dir_name, routing_verilog_file_name);
fprintf(fp, " ${verilog_path}%s%s ] \n",
default_submodule_dir_name, submodule_verilog_file_name);
fprintf(fp, "\n");
fprintf(fp, "#Source the tcl script\n");
fprintf(fp, "source ${verilog_path}%s\n", modelsim_proc_auto_script_filename);
fprintf(fp, "\n");
fprintf(fp, "#Execute the top level procedure\n");
fprintf(fp, "top_create_new_project $projectname $verilog_files $project_path $simtime $unit\n");
fprintf(fp, "\n");
fprintf(fp, "#Relaunch simulation\n");
/* Close File handler */
fclose(fp);
return;
}
/***** Top-level function *****/
void dump_verilog_modelsim_autodeck(t_sram_orgz_info* cur_sram_orgz_info,
t_spice spice,
@ -307,16 +508,23 @@ void dump_verilog_modelsim_autodeck(t_sram_orgz_info* cur_sram_orgz_info,
char* chomped_circuit_name,
char* simulator_ini_path,
boolean include_timing,
boolean init_sim) {
boolean init_sim,
boolean print_top_tb,
boolean print_top_auto_tb) {
char* modelsim_project_name = NULL;
char* modelsim_proc_script_filename = NULL;
char* modelsim_top_script_filename = NULL;
char* modelsim_proc_auto_script_filename = NULL;
char* modelsim_top_auto_script_filename = NULL;
char* auto_tb_postfix = "_autocheck";
float simulation_time_period = 0.;
/* Determine the project name for Modelsim */
modelsim_project_name = my_strcat(chomped_circuit_name, modelsim_project_name_postfix);
modelsim_top_script_filename = my_strcat(verilog_dir_formatted, my_strcat(chomped_circuit_name, modelsim_top_script_name_postfix));
modelsim_proc_script_filename = my_strcat(verilog_dir_formatted, my_strcat(chomped_circuit_name, modelsim_proc_script_name_postfix));
modelsim_top_auto_script_filename = my_strcat(verilog_dir_formatted, my_strcat(chomped_circuit_name, my_strcat(auto_tb_postfix, modelsim_top_script_name_postfix)));
modelsim_proc_auto_script_filename = my_strcat(verilog_dir_formatted, my_strcat(chomped_circuit_name, my_strcat(auto_tb_postfix, modelsim_proc_script_name_postfix)));
/* Generate files */
vpr_printf(TIO_MESSAGE_INFO, "Writing Modelsim simulation deck auto-generation scripts...\n");
@ -330,11 +538,18 @@ void dump_verilog_modelsim_autodeck(t_sram_orgz_info* cur_sram_orgz_info,
}
/* Dump the Modelsim process function file */
dump_verilog_modelsim_proc_script(modelsim_proc_script_filename,
if(print_top_tb){
dump_verilog_modelsim_proc_script(modelsim_proc_script_filename,
simulator_ini_path, chomped_circuit_name,
include_timing, init_sim,
modelsim_project_name);
}
if(print_top_auto_tb){
dump_verilog_modelsim_proc_auto_script(modelsim_proc_auto_script_filename,
simulator_ini_path, chomped_circuit_name,
include_timing, init_sim,
modelsim_project_name);
}
/* Compute simulation time period */
simulation_time_period = get_verilog_modelsim_simulation_time_period(convert_modelsim_time_unit_to_float(modelsim_simulation_time_unit),
get_sram_orgz_info_num_mem_bit(cur_sram_orgz_info),
@ -343,13 +558,22 @@ void dump_verilog_modelsim_autodeck(t_sram_orgz_info* cur_sram_orgz_info,
1./spice.spice_params.stimulate_params.op_clock_freq);
/* Dump the Modelsim top-level script file */
dump_verilog_modelsim_top_script(modelsim_top_script_filename,
if(print_top_tb){
dump_verilog_modelsim_top_script(modelsim_top_script_filename,
my_strcat(chomped_circuit_name, modelsim_proc_script_name_postfix),
verilog_dir_formatted,
chomped_circuit_name, modelsim_project_name,
simulation_time_period, modelsim_simulation_time_unit,
spice);
}
if(print_top_auto_tb){
dump_verilog_modelsim_top_auto_script(modelsim_top_auto_script_filename,
my_strcat(chomped_circuit_name, my_strcat( auto_tb_postfix, modelsim_proc_script_name_postfix)),
verilog_dir_formatted,
chomped_circuit_name, modelsim_project_name,
simulation_time_period, modelsim_simulation_time_unit,
spice);
}
/* Free */
my_free(modelsim_project_name);
my_free(modelsim_proc_script_filename);

4
vpr7_x2p/vpr/SRC/fpga_spice/verilog/verilog_modelsim_autodeck.h
View File

@ -6,4 +6,6 @@ void dump_verilog_modelsim_autodeck(t_sram_orgz_info* cur_sram_orgz_info,
char* chomped_circuit_name,
char* simulator_ini_path,
boolean include_timing,
boolean init_sim);
boolean init_sim,
boolean print_top_tb,
boolean print_top_auto_tb);