[test] create a new example script for fixed routing W case

openfpga_flow/openfpga_shell_scripts/global_tile_clock_full_testbench_example_script.openfpga

@@ -2,7 +2,7 @@
 # When the global clock is defined as a port of a tile, clock routing in VPR should be skipped
 # This is due to the Fc_in of clock port is set to 0 for global wiring
 #--write_rr_graph example_rr_graph.xml
-vpr ${VPR_ARCH_FILE} ${VPR_TESTBENCH_BLIF} --device ${OPENFPGA_VPR_DEVICE_LAYOUT} --route_chan_width ${OPENFPGA_VPR_ROUTE_CHAN_WIDTH}
+vpr ${VPR_ARCH_FILE} ${VPR_TESTBENCH_BLIF} --device ${OPENFPGA_VPR_DEVICE_LAYOUT}
 
 # Read OpenFPGA architecture definition
 read_openfpga_arch -f ${OPENFPGA_ARCH_FILE}

openfpga_flow/openfpga_shell_scripts/global_tile_clock_full_testbench_fix_routeW_example_script.openfpga

@@ -0,0 +1,73 @@
+# Run VPR for the 'and' design
+# When the global clock is defined as a port of a tile, clock routing in VPR should be skipped
+# This is due to the Fc_in of clock port is set to 0 for global wiring
+#--write_rr_graph example_rr_graph.xml
+vpr ${VPR_ARCH_FILE} ${VPR_TESTBENCH_BLIF} --device ${OPENFPGA_VPR_DEVICE_LAYOUT} --route_chan_width ${OPENFPGA_VPR_ROUTE_CHAN_WIDTH}
+
+# Read OpenFPGA architecture definition
+read_openfpga_arch -f ${OPENFPGA_ARCH_FILE}
+
+# Read OpenFPGA simulation settings
+read_openfpga_simulation_setting -f ${OPENFPGA_SIM_SETTING_FILE}
+
+# Annotate the OpenFPGA architecture to VPR data base
+# to debug use --verbose options
+link_openfpga_arch --activity_file ${ACTIVITY_FILE} --sort_gsb_chan_node_in_edges
+
+# Check and correct any naming conflicts in the BLIF netlist
+check_netlist_naming_conflict --fix --report ./netlist_renaming.xml
+
+# Apply fix-up to Look-Up Table truth tables based on packing results
+lut_truth_table_fixup
+
+# Build the module graph
+#  - Enabled compression on routing architecture modules
+#  - Enable pin duplication on grid modules
+build_fabric --compress_routing #--verbose
+
+# Write the fabric hierarchy of module graph to a file
+# This is used by hierarchical PnR flows
+write_fabric_hierarchy --file ./fabric_hierarchy.txt
+
+# Repack the netlist to physical pbs
+# This must be done before bitstream generator and testbench generation
+# Strongly recommend it is done after all the fix-up have been applied
+repack #--verbose
+
+# Build the bitstream
+#  - Output the fabric-independent bitstream to a file
+build_architecture_bitstream --verbose --write_file fabric_independent_bitstream.xml
+
+# Build fabric-dependent bitstream
+build_fabric_bitstream --verbose
+
+# Write fabric-dependent bitstream
+write_fabric_bitstream --file fabric_bitstream.bit --format plain_text
+
+# Write the Verilog netlist for FPGA fabric
+#  - Enable the use of explicit port mapping in Verilog netlist
+write_fabric_verilog --file ./SRC --explicit_port_mapping --include_timing --print_user_defined_template --verbose
+
+# Write the Verilog testbench for FPGA fabric
+#  - We suggest the use of same output directory as fabric Verilog netlists
+#  - Must specify the reference benchmark file if you want to output any testbenches
+#  - Enable top-level testbench which is a full verification including programming circuit and core logic of FPGA
+#  - Enable pre-configured top-level testbench which is a fast verification skipping programming phase
+#  - Simulation ini file is optional and is needed only when you need to interface different HDL simulators using openfpga flow-run scripts
+write_full_testbench --file ./SRC --reference_benchmark_file_path ${REFERENCE_VERILOG_TESTBENCH} --explicit_port_mapping --include_signal_init --bitstream fabric_bitstream.bit
+
+# Write the SDC files for PnR backend
+#  - Turn on every options here
+write_pnr_sdc --file ./SDC
+
+# Write SDC to disable timing for configure ports
+write_sdc_disable_timing_configure_ports --file ./SDC/disable_configure_ports.sdc
+
+# Write the SDC to run timing analysis for a mapped FPGA fabric
+write_analysis_sdc --file ./SDC_analysis
+
+# Finish and exit OpenFPGA
+exit
+
+# Note :
+# To run verification at the end of the flow maintain source in ./SRC directory

openfpga_flow/tasks/basic_tests/global_tile_ports/global_tile_clock/config/task.conf

@@ -16,7 +16,7 @@ timeout_each_job = 20*60
 fpga_flow=yosys_vpr
 
 [OpenFPGA_SHELL]
-openfpga_shell_template=${PATH:OPENFPGA_PATH}/openfpga_flow/openfpga_shell_scripts/global_tile_clock_full_testbench_example_script.openfpga
+openfpga_shell_template=${PATH:OPENFPGA_PATH}/openfpga_flow/openfpga_shell_scripts/global_tile_clock_full_testbench_fix_routeW_example_script.openfpga
 openfpga_arch_file=${PATH:OPENFPGA_PATH}/openfpga_flow/openfpga_arch/k4_N4_40nm_GlobalTileClk_cc_openfpga.xml
 openfpga_sim_setting_file=${PATH:OPENFPGA_PATH}/openfpga_flow/openfpga_simulation_settings/auto_sim_openfpga.xml
 openfpga_vpr_device_layout=auto

openfpga_flow/tasks/basic_tests/global_tile_ports/global_tile_clock_subtile/config/task.conf

@@ -16,7 +16,7 @@ timeout_each_job = 20*60
 fpga_flow=yosys_vpr
 
 [OpenFPGA_SHELL]
-openfpga_shell_template=${PATH:OPENFPGA_PATH}/openfpga_flow/openfpga_shell_scripts/global_tile_clock_full_testbench_example_script.openfpga
+openfpga_shell_template=${PATH:OPENFPGA_PATH}/openfpga_flow/openfpga_shell_scripts/global_tile_clock_full_testbench_fix_routeW_example_script.openfpga
 openfpga_arch_file=${PATH:OPENFPGA_PATH}/openfpga_flow/openfpga_arch/k4_N4_40nm_GlobalTileClk_registerable_io_cc_openfpga.xml
 openfpga_sim_setting_file=${PATH:OPENFPGA_PATH}/openfpga_flow/openfpga_simulation_settings/auto_sim_openfpga.xml
 openfpga_vpr_device_layout=2x2_hybrid_io

openfpga_flow/tasks/basic_tests/global_tile_ports/global_tile_clock_subtile_port_merge/config/task.conf

@@ -16,7 +16,7 @@ timeout_each_job = 20*60
 fpga_flow=yosys_vpr
 
 [OpenFPGA_SHELL]
-openfpga_shell_template=${PATH:OPENFPGA_PATH}/openfpga_flow/openfpga_shell_scripts/global_tile_clock_full_testbench_example_script.openfpga
+openfpga_shell_template=${PATH:OPENFPGA_PATH}/openfpga_flow/openfpga_shell_scripts/global_tile_clock_full_testbench_fix_routeW_example_script.openfpga
 openfpga_arch_file=${PATH:OPENFPGA_PATH}/openfpga_flow/openfpga_arch/k4_N4_40nm_GlobalTileClkMergeSubtilePort_registerable_io_cc_openfpga.xml
 openfpga_sim_setting_file=${PATH:OPENFPGA_PATH}/openfpga_flow/openfpga_simulation_settings/auto_sim_openfpga.xml
 openfpga_vpr_device_layout=2x2_hybrid_io