202 lines
5.1 KiB
INI
202 lines
5.1 KiB
INI
# DM355 EVM board
|
|
# http://focus.ti.com/docs/toolsw/folders/print/tmdsevm355.html
|
|
# http://c6000.spectrumdigital.com/evmdm355/
|
|
|
|
source [find target/ti_dm355.cfg]
|
|
|
|
reset_config trst_and_srst separate
|
|
|
|
# NOTE: disable or replace this call to dm355evm_init if you're
|
|
# debugging new UBL code from SRAM.
|
|
$_TARGETNAME configure -event reset-init { dm355evm_init }
|
|
|
|
#
|
|
# This post-reset init is called when the MMU isn't active, all IRQs
|
|
# are disabled, etc. It should do most of what a UBL does, except for
|
|
# loading code (like U-Boot) into DRAM and running it.
|
|
#
|
|
proc dm355evm_init {} {
|
|
global dm355
|
|
|
|
puts "Initialize DM355 EVM board"
|
|
|
|
# CLKIN = 24 MHz ... can't talk quickly to ARM yet
|
|
jtag_rclk 1500
|
|
|
|
########################
|
|
# PLL1 = 432 MHz (/8, x144)
|
|
# ...SYSCLK1 = 216 MHz (/2) ... ARM, MJCP
|
|
# ...SYSCLK2 = 108 MHz (/4) ... Peripherals
|
|
# ...SYSCLK3 = 27 MHz (/16) ... VPBE, DAC
|
|
# ...SYSCLK4 = 108 MHz (/4) ... VPSS
|
|
# pll1.{prediv,div1,div2} are fixed
|
|
# pll1.postdiv set in MISC (for *this* speed grade)
|
|
|
|
set addr [dict get $dm355 pllc1]
|
|
set pll_divs [dict create]
|
|
dict set pll_divs div3 16
|
|
dict set pll_divs div4 4
|
|
pll_v02_setup $addr 144 $pll_divs
|
|
|
|
# ARM is now running at 216 MHz, so JTAG can go faster
|
|
jtag_rclk 20000
|
|
|
|
########################
|
|
# PLL2 = 342 MHz (/8, x114)
|
|
# ....SYSCLK1 = 342 MHz (/1) ... DDR PHY at 171 MHz, 2x clock
|
|
# pll2.{postdiv,div1} are fixed
|
|
|
|
set addr [dict get $dm355 pllc2]
|
|
set pll_divs [dict create]
|
|
dict set pll_divs div1 1
|
|
dict set pll_divs prediv 8
|
|
pll_v02_setup $addr 114 $pll_divs
|
|
|
|
########################
|
|
# PINMUX
|
|
|
|
# All Video Inputs
|
|
davinci_pinmux $dm355 0 0x00007f55
|
|
# All Video Outputs
|
|
davinci_pinmux $dm355 1 0x00145555
|
|
# EMIFA (NOTE: more could be set up for use as GPIOs)
|
|
davinci_pinmux $dm355 2 0x00000c08
|
|
# SPI0, SPI1, UART1, I2C, SD0, SD1, McBSP0, CLKOUTs
|
|
davinci_pinmux $dm355 3 0x1bff55ff
|
|
# MMC/SD0 instead of MS; SPI0
|
|
davinci_pinmux $dm355 4 0x00000000
|
|
|
|
########################
|
|
# PSC setup (minimal)
|
|
|
|
# DDR EMIF/13, AEMIF/14, UART0/19
|
|
psc_enable 13
|
|
psc_enable 14
|
|
psc_enable 19
|
|
psc_go
|
|
|
|
########################
|
|
# DDR2 EMIF
|
|
|
|
# VTPIOCR impedance calibration
|
|
set addr [dict get $dm355 sysbase]
|
|
set addr [expr $addr + 0x70]
|
|
|
|
# clear CLR, LOCK, PWRDN; wait a clock; set CLR
|
|
mmw $addr 0 0x20c0
|
|
mmw $addr 0x2000 0
|
|
|
|
# wait for READY
|
|
while { [expr [mrw $addr] & 0x8000] == 0 } { sleep 1 }
|
|
|
|
# set IO_READY; then LOCK and PWRSAVE; then PWRDN
|
|
mmw $addr 0x4000 0
|
|
mmw $addr 0x0180 0
|
|
mmw $addr 0x0040 0
|
|
|
|
# NOTE: this DDR2 initialization sequence borrows from
|
|
# both UBL 1.50 and the SPRUEH7D DDR2 EMIF spec.
|
|
|
|
# reset (then re-enable) DDR controller
|
|
psc_reset 13
|
|
psc_go
|
|
psc_enable 13
|
|
psc_go
|
|
|
|
# now set it up for Micron MT47H64M16HR-37E @ 171 MHz
|
|
|
|
set addr [dict get $dm355 ddr_emif]
|
|
|
|
# DDRPHYCR1
|
|
mww [expr $addr + 0xe4] 0x50006404
|
|
|
|
# PBBPR -- burst priority
|
|
mww [expr $addr + 0x20] 0xfe
|
|
|
|
# SDCR -- unlock boot config; init for DDR2, relock, unlock SDTIM*
|
|
mmw [expr $addr + 0x08] 0x00800000 0
|
|
mmw [expr $addr + 0x08] 0x0013c632 0x03870fff
|
|
|
|
# SDTIMR, SDTIMR2
|
|
mww [expr $addr + 0x10] 0x2a923249
|
|
mww [expr $addr + 0x14] 0x4c17c763
|
|
|
|
# SDCR -- relock SDTIM*
|
|
mmw [expr $addr + 0x08] 0 0x00008000
|
|
|
|
# SDRCR -- refresh rate (171 MHz * 7.8usec)
|
|
mww [expr $addr + 0x0c] 1336
|
|
|
|
########################
|
|
# ASYNC EMIF
|
|
|
|
set addr [dict get $dm355 a_emif]
|
|
|
|
# slow/pessimistic timings
|
|
set nand_timings 0x40400204
|
|
# fast (25% faster page reads)
|
|
#set nand_timings 0x0400008c
|
|
|
|
# AWCCR
|
|
mww [expr $addr + 0x04] 0xff
|
|
# CS0 == socketed NAND (default MT29F16G08FAA, 2GByte)
|
|
mww [expr $addr + 0x10] $nand_timings
|
|
# CS1 == dm9000 Ethernet
|
|
mww [expr $addr + 0x14] 0x00a00505
|
|
# NANDFCR -- only CS0 has NAND
|
|
mww [expr $addr + 0x60] 0x01
|
|
|
|
# default: both chipselects to the NAND socket are used
|
|
nand probe 0
|
|
nand probe 1
|
|
|
|
########################
|
|
# UART0
|
|
|
|
set addr [dict get $dm355 uart0]
|
|
|
|
# PWREMU_MGNT -- rx + tx in reset
|
|
mww [expr $addr + 0x30] 0
|
|
|
|
# DLL, DLH -- 115200 baud
|
|
mwb [expr $addr + 0x20] 0x0d
|
|
mwb [expr $addr + 0x24] 0x00
|
|
|
|
# FCR - clear and disable FIFOs
|
|
mwb [expr $addr + 0x08] 0x07
|
|
mwb [expr $addr + 0x08] 0x00
|
|
|
|
# IER - disable IRQs
|
|
mwb [expr $addr + 0x04] 0x00
|
|
|
|
# LCR - 8-N-1
|
|
mwb [expr $addr + 0x0c] 0x03
|
|
|
|
# MCR - no flow control or loopback
|
|
mwb [expr $addr + 0x10] 0x00
|
|
|
|
# PWREMU_MGNT -- rx + tx normal, free running during JTAG halt
|
|
mww [expr $addr + 0x30] 0xe001
|
|
|
|
|
|
########################
|
|
|
|
# turn on icache - set I bit in cp15 register c1
|
|
mcr 15 0 0 1 0 0x00051078
|
|
}
|
|
|
|
# NAND -- socket has two chipselects, MT29F16G08FAA puts 1GByte on each one.
|
|
#
|
|
# NOTE: "hwecc4" here presumes that if you're using the standard 2GB NAND
|
|
# you either (a) have 'new' DM355 chips, with boot ROMs that don't need to
|
|
# use "hwecc4_infix" for the UBL; or else (b) aren't updating anything that
|
|
# needs infix layout ... like an old UBL, old U-Boot, old MVL kernel, etc.
|
|
set _FLASHNAME $_CHIPNAME.boot
|
|
nand device $_FLASHNAME davinci $_TARGETNAME 0x02000000 hwecc4 0x01e10000
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
nand device $_FLASHNAME davinci $_TARGETNAME 0x02004000 hwecc4 0x01e10000
|
|
|
|
# FIXME
|
|
# - support writing UBL with its header (new layout only with new ROMs)
|
|
# - support writing ABL/U-Boot with its header (new layout)
|