166 lines
3.6 KiB
INI
166 lines
3.6 KiB
INI
# http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4394
|
|
#
|
|
# use combined on interfaces or targets that can't set TRST/SRST separately
|
|
reset_config trst_and_srst srst_pulls_trst
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME cap7
|
|
}
|
|
|
|
if { [info exists ENDIAN] } {
|
|
set _ENDIAN $ENDIAN
|
|
} else {
|
|
set _ENDIAN little
|
|
}
|
|
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
set _CPUTAPID 0x40700f0f
|
|
}
|
|
|
|
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME
|
|
|
|
$_TARGETNAME configure -event reset-start {
|
|
# start off real slow when we're running off internal RC oscillator
|
|
adapter speed 32
|
|
}
|
|
|
|
proc peek32 {address} {
|
|
mem2array t 32 $address 1
|
|
return $t(0)
|
|
}
|
|
|
|
# Wait for an expression to be true with a timeout
|
|
proc wait_state {expression} {
|
|
for {set i 0} {$i < 1000} {set i [expr $i + 1]} {
|
|
if {[uplevel 1 $expression] == 0} {
|
|
return
|
|
}
|
|
}
|
|
return -code 1 "Timed out"
|
|
}
|
|
|
|
# Use a global variable here to be able to tinker interactively with
|
|
# post reset jtag frequency.
|
|
global post_reset_khz
|
|
# Danger!!!! Even 16MHz kinda works with this target, but
|
|
# it needs to be as low as 2000kHz to be stable.
|
|
set post_reset_khz 2000
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
echo "Configuring master clock"
|
|
# disable watchdog
|
|
mww 0xfffffd44 0xff008000
|
|
# enable user reset
|
|
mww 0xfffffd08 0xa5000001
|
|
# Enable main oscillator
|
|
mww 0xFFFFFc20 0x00000f01
|
|
wait_state {expr {([peek32 0xFFFFFC68] & 0x1) == 0}}
|
|
|
|
# Set PLLA to 96MHz
|
|
mww 0xFFFFFc28 0x20072801
|
|
wait_state {expr {([peek32 0xFFFFFC68] & 0x2) == 0}}
|
|
|
|
# Select prescaler
|
|
mww 0xFFFFFC30 0x00000004
|
|
wait_state {expr {([peek32 0xFFFFFC68] & 0x8) == 0}}
|
|
|
|
# Select master clock to 48MHz
|
|
mww 0xFFFFFC30 0x00000006
|
|
wait_state {expr {([peek32 0xFFFFFC68] & 0x8) == 0}}
|
|
|
|
echo "Master clock ok."
|
|
|
|
# Now that we're up and running, crank up speed!
|
|
global post_reset_khz ; adapter speed $post_reset_khz
|
|
|
|
echo "Configuring the SDRAM controller..."
|
|
|
|
# Configure EBI Chip select for SDRAM
|
|
mww 0xFFFFEF30 0x00000102
|
|
|
|
# Enable clock on EBI PIOs
|
|
mww 0xFFFFFC10 0x00000004
|
|
|
|
# Configure PIO for SDRAM
|
|
mww 0xFFFFF470 0xFFFF0000
|
|
mww 0xFFFFF474 0x00000000
|
|
mww 0xFFFFF404 0xFFFF0000
|
|
|
|
# Configure SDRAMC CR
|
|
mww 0xFFFFEA08 0xA63392F9
|
|
|
|
# NOP command
|
|
mww 0xFFFFEA00 0x1
|
|
mww 0x20000000 0
|
|
|
|
# Precharge All Banks command
|
|
mww 0xFFFFEA00 0x2
|
|
mww 0x20000000 0
|
|
|
|
# Set 1st CBR
|
|
mww 0xFFFFEA00 0x00000004
|
|
mww 0x20000010 0x00000001
|
|
|
|
# Set 2nd CBR
|
|
mww 0xFFFFEA00 0x00000004
|
|
mww 0x20000020 0x00000002
|
|
|
|
# Set 3rd CBR
|
|
mww 0xFFFFEA00 0x00000004
|
|
mww 0x20000030 0x00000003
|
|
|
|
# Set 4th CBR
|
|
mww 0xFFFFEA00 0x00000004
|
|
mww 0x20000040 0x00000004
|
|
|
|
# Set 5th CBR
|
|
mww 0xFFFFEA00 0x00000004
|
|
mww 0x20000050 0x00000005
|
|
|
|
# Set 6th CBR
|
|
mww 0xFFFFEA00 0x00000004
|
|
mww 0x20000060 0x00000006
|
|
|
|
# Set 7th CBR
|
|
mww 0xFFFFEA00 0x00000004
|
|
mww 0x20000070 0x00000007
|
|
|
|
# Set 8th CBR
|
|
mww 0xFFFFEA00 0x00000004
|
|
mww 0x20000080 0x00000008
|
|
|
|
# Set LMR operation
|
|
mww 0xFFFFEA00 0x00000003
|
|
|
|
# Perform LMR burst=1, lat=2
|
|
mww 0x20000020 0xCAFEDEDE
|
|
|
|
# Set Refresh Timer
|
|
mww 0xFFFFEA04 0x00000203
|
|
|
|
# Set Normal mode
|
|
mww 0xFFFFEA00 0x00000000
|
|
mww 0x20000000 0x00000000
|
|
|
|
#remap internal memory at address 0x0
|
|
mww 0xffffef00 0x3
|
|
|
|
echo "SDRAM configuration ok."
|
|
}
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0
|
|
|
|
arm7_9 dcc_downloads enable
|
|
arm7_9 fast_memory_access enable
|
|
|
|
#set _FLASHNAME $_CHIPNAME.flash
|
|
#flash bank $_FLASHNAME at91sam7 0 0 0 0 $_TARGETNAME 0 0 0 0 0 0 0 18432
|
|
|