188 lines
4.9 KiB
INI
188 lines
4.9 KiB
INI
# script for stm32wlx family
|
|
|
|
#
|
|
# stm32wl devices support both JTAG and SWD transports.
|
|
#
|
|
source [find target/swj-dp.tcl]
|
|
source [find mem_helper.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME stm32wlx
|
|
}
|
|
|
|
if { [info exists DUAL_CORE] } {
|
|
set $_CHIPNAME.DUAL_CORE $DUAL_CORE
|
|
unset DUAL_CORE
|
|
} else {
|
|
set $_CHIPNAME.DUAL_CORE 0
|
|
}
|
|
|
|
if { [info exists WKUP_CM0P] } {
|
|
set $_CHIPNAME.WKUP_CM0P $WKUP_CM0P
|
|
unset WKUP_CM0P
|
|
} else {
|
|
set $_CHIPNAME.WKUP_CM0P 0
|
|
}
|
|
|
|
# Issue a warning when hla is used, and fallback to single core configuration
|
|
if { [set $_CHIPNAME.DUAL_CORE] && [using_hla] } {
|
|
echo "Warning : hla does not support multicore debugging"
|
|
set $_CHIPNAME.DUAL_CORE 0
|
|
set $_CHIPNAME.WKUP_CM0P 0
|
|
}
|
|
|
|
# setup the Work-area start address and size
|
|
# Work-area is a space in RAM used for flash programming
|
|
|
|
# Memory map for known devices:
|
|
# STM32WL x5JC x5JB x5J8
|
|
# FLASH 256 128 64
|
|
# SRAM1 32 16 0
|
|
# SRAM2 32 32 20
|
|
|
|
# By default use 8kB
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x2000
|
|
}
|
|
|
|
# Use SRAM2 as work area (some devices do not have SRAM1):
|
|
set WORKAREASTART_CM4 0x20008000
|
|
set WORKAREASTART_CM0P [expr {$WORKAREASTART_CM4 + $_WORKAREASIZE}]
|
|
|
|
#jtag scan chain
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
if { [using_jtag] } {
|
|
set _CPUTAPID 0x6ba00477
|
|
} else {
|
|
# SWD IDCODE (single drop, arm)
|
|
set _CPUTAPID 0x6ba02477
|
|
}
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
|
|
|
if {[using_jtag]} {
|
|
jtag newtap $_CHIPNAME bs -irlen 5
|
|
}
|
|
|
|
target create $_CHIPNAME.cpu0 cortex_m -endian little -dap $_CHIPNAME.dap
|
|
|
|
$_CHIPNAME.cpu0 configure -work-area-phys $WORKAREASTART_CM4 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
flash bank $_CHIPNAME.flash.cpu0 stm32l4x 0x08000000 0 0 0 $_CHIPNAME.cpu0
|
|
flash bank $_CHIPNAME.otp.cpu0 stm32l4x 0x1fff7000 0 0 0 $_CHIPNAME.cpu0
|
|
|
|
if {![using_hla]} {
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
$_CHIPNAME.cpu0 cortex_m reset_config sysresetreq
|
|
}
|
|
|
|
$_CHIPNAME.cpu0 configure -event reset-init {
|
|
# CPU comes out of reset with MSI_ON | MSI_RDY | MSI Range 4 MHz.
|
|
# Configure system to use MSI 24 MHz clock, compliant with VOS default Range1.
|
|
# 2 WS compliant with VOS=Range1 and 24 MHz.
|
|
mmw 0x58004000 0x00000102 0 ;# FLASH_ACR |= PRFTEN | 2(Latency)
|
|
mmw 0x58000000 0x00000091 0 ;# RCC_CR = MSI_ON | MSI Range 24 MHz
|
|
# Boost JTAG frequency
|
|
adapter speed 4000
|
|
}
|
|
|
|
$_CHIPNAME.cpu0 configure -event reset-start {
|
|
# Reset clock is MSI (4 MHz)
|
|
adapter speed 500
|
|
}
|
|
|
|
$_CHIPNAME.cpu0 configure -event examine-end {
|
|
# Enable debug during low power modes (uses more power)
|
|
# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
|
|
mmw 0xE0042004 0x00000007 0
|
|
|
|
# Stop watchdog counters during halt
|
|
# DBGMCU_APB1_FZR1 |= DBG_IWDG_STOP | DBG_WWDG_STOP
|
|
mmw 0xE004203C 0x00001800 0
|
|
|
|
set _CHIPNAME [stm32wlx_get_chipname]
|
|
global $_CHIPNAME.WKUP_CM0P
|
|
|
|
if {[set $_CHIPNAME.WKUP_CM0P]} {
|
|
stm32wlx_wkup_cm0p
|
|
}
|
|
}
|
|
|
|
$_CHIPNAME.cpu0 configure -event trace-config {
|
|
# nothing to do
|
|
}
|
|
|
|
if {[set $_CHIPNAME.DUAL_CORE]} {
|
|
target create $_CHIPNAME.cpu1 cortex_m -endian little -dap $_CHIPNAME.dap -ap-num 1
|
|
|
|
$_CHIPNAME.cpu0 configure -work-area-phys $WORKAREASTART_CM0P -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
flash bank $_CHIPNAME.flash.cpu1 stm32l4x 0x08000000 0 0 0 $_CHIPNAME.cpu1
|
|
flash bank $_CHIPNAME.otp.cpu1 stm32l4x 0x1fff7000 0 0 0 $_CHIPNAME.cpu1
|
|
|
|
if {![using_hla]} {
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
$_CHIPNAME.cpu1 cortex_m reset_config sysresetreq
|
|
}
|
|
|
|
proc stm32wlx_wkup_cm0p {} {
|
|
set _CHIPNAME [stm32wlx_get_chipname]
|
|
|
|
# enable CPU2 boot after reset and after wakeup from Stop or Standby mode
|
|
# PWR_CR4 |= C2BOOT
|
|
stm32wlx_mmw $_CHIPNAME.cpu0 0x5800040C 0x00008000 0
|
|
}
|
|
}
|
|
|
|
# get _CHIPNAME from current target
|
|
proc stm32wlx_get_chipname {} {
|
|
set t [target current]
|
|
set sep [string last "." $t]
|
|
if {$sep == -1} {
|
|
return $t
|
|
}
|
|
return [string range $t 0 [expr {$sep - 1}]]
|
|
}
|
|
|
|
# like mrw, but with target selection
|
|
proc stm32wlx_mrw {used_target reg} {
|
|
set value ""
|
|
$used_target mem2array value 32 $reg 1
|
|
return $value(0)
|
|
}
|
|
|
|
# like mmw, but with target selection
|
|
proc stm32wlx_mmw {used_target reg setbits clearbits} {
|
|
set old [stm32wlx_mrw $used_target $reg]
|
|
set new [expr {($old & ~$clearbits) | $setbits}]
|
|
$used_target mww $reg $new
|
|
}
|
|
|
|
# Make sure that cpu0 is selected
|
|
targets $_CHIPNAME.cpu0
|
|
|
|
# Common knowledges tells JTAG speed should be <= F_CPU/6.
|
|
# F_CPU after reset is MSI 4MHz, so use F_JTAG = 500 kHz to stay on
|
|
# the safe side.
|
|
#
|
|
# Note that there is a pretty wide band where things are
|
|
# more or less stable, see http://openocd.zylin.com/#/c/3366/
|
|
adapter speed 500
|
|
|
|
adapter srst delay 100
|
|
if {[using_jtag]} {
|
|
jtag_ntrst_delay 100
|
|
}
|
|
|
|
reset_config srst_nogate
|