309 lines
9.2 KiB
INI
309 lines
9.2 KiB
INI
# script for stm32h7x family
|
|
|
|
#
|
|
# stm32h7 devices support both JTAG and SWD transports.
|
|
#
|
|
source [find target/swj-dp.tcl]
|
|
source [find mem_helper.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME stm32h7x
|
|
}
|
|
|
|
if { [info exists DUAL_BANK] } {
|
|
set $_CHIPNAME.DUAL_BANK $DUAL_BANK
|
|
unset DUAL_BANK
|
|
} else {
|
|
set $_CHIPNAME.DUAL_BANK 0
|
|
}
|
|
|
|
if { [info exists DUAL_CORE] } {
|
|
set $_CHIPNAME.DUAL_CORE $DUAL_CORE
|
|
unset DUAL_CORE
|
|
} else {
|
|
set $_CHIPNAME.DUAL_CORE 0
|
|
}
|
|
|
|
# Issue a warning when hla is used, and fallback to single core configuration
|
|
if { [set $_CHIPNAME.DUAL_CORE] && [using_hla] } {
|
|
echo "Warning : hla does not support multicore debugging"
|
|
set $_CHIPNAME.DUAL_CORE 0
|
|
}
|
|
|
|
if { [info exists USE_CTI] } {
|
|
set $_CHIPNAME.USE_CTI $USE_CTI
|
|
unset USE_CTI
|
|
} else {
|
|
set $_CHIPNAME.USE_CTI 0
|
|
}
|
|
|
|
# Issue a warning when DUAL_CORE=0 and USE_CTI=1, and fallback to USE_CTI=0
|
|
if { ![set $_CHIPNAME.DUAL_CORE] && [set $_CHIPNAME.USE_CTI] } {
|
|
echo "Warning : could not use CTI with a single core device, CTI is disabled"
|
|
set $_CHIPNAME.USE_CTI 0
|
|
}
|
|
|
|
set _ENDIAN little
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# By default use 64kB
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x10000
|
|
}
|
|
|
|
#jtag scan chain
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
if { [using_jtag] } {
|
|
set _CPUTAPID 0x6ba00477
|
|
} {
|
|
set _CPUTAPID 0x6ba02477
|
|
}
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
|
|
|
if {[using_jtag]} {
|
|
jtag newtap $_CHIPNAME bs -irlen 5
|
|
}
|
|
|
|
if {![using_hla]} {
|
|
# STM32H7 provides an APB-AP at access port 2, which allows the access to
|
|
# the debug and trace features on the system APB System Debug Bus (APB-D).
|
|
target create $_CHIPNAME.ap2 mem_ap -dap $_CHIPNAME.dap -ap-num 2
|
|
swo create $_CHIPNAME.swo -dap $_CHIPNAME.dap -ap-num 2 -baseaddr 0xE00E3000
|
|
tpiu create $_CHIPNAME.tpiu -dap $_CHIPNAME.dap -ap-num 2 -baseaddr 0xE00F5000
|
|
}
|
|
|
|
target create $_CHIPNAME.cpu0 cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap -ap-num 0
|
|
|
|
$_CHIPNAME.cpu0 configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
flash bank $_CHIPNAME.bank1.cpu0 stm32h7x 0x08000000 0 0 0 $_CHIPNAME.cpu0
|
|
|
|
if {[set $_CHIPNAME.DUAL_BANK]} {
|
|
flash bank $_CHIPNAME.bank2.cpu0 stm32h7x 0x08100000 0 0 0 $_CHIPNAME.cpu0
|
|
}
|
|
|
|
if {[set $_CHIPNAME.DUAL_CORE]} {
|
|
target create $_CHIPNAME.cpu1 cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap -ap-num 3
|
|
|
|
$_CHIPNAME.cpu1 configure -work-area-phys 0x38000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
flash bank $_CHIPNAME.bank1.cpu1 stm32h7x 0x08000000 0 0 0 $_CHIPNAME.cpu1
|
|
|
|
if {[set $_CHIPNAME.DUAL_BANK]} {
|
|
flash bank $_CHIPNAME.bank2.cpu1 stm32h7x 0x08100000 0 0 0 $_CHIPNAME.cpu1
|
|
}
|
|
}
|
|
|
|
# Make sure that cpu0 is selected
|
|
targets $_CHIPNAME.cpu0
|
|
|
|
if { [info exists QUADSPI] && $QUADSPI } {
|
|
set a [llength [flash list]]
|
|
set _QSPINAME $_CHIPNAME.qspi
|
|
flash bank $_QSPINAME stmqspi 0x90000000 0 0 0 $_CHIPNAME.cpu0 0x52005000
|
|
} else {
|
|
if { [info exists OCTOSPI1] && $OCTOSPI1 } {
|
|
set a [llength [flash list]]
|
|
set _OCTOSPINAME1 $_CHIPNAME.octospi1
|
|
flash bank $_OCTOSPINAME1 stmqspi 0x90000000 0 0 0 $_CHIPNAME.cpu0 0x52005000
|
|
}
|
|
if { [info exists OCTOSPI2] && $OCTOSPI2 } {
|
|
set b [llength [flash list]]
|
|
set _OCTOSPINAME2 $_CHIPNAME.octospi2
|
|
flash bank $_OCTOSPINAME2 stmqspi 0x70000000 0 0 0 $_CHIPNAME.cpu0 0x5200A000
|
|
}
|
|
}
|
|
|
|
# Clock after reset is HSI at 64 MHz, no need of PLL
|
|
adapter speed 1800
|
|
|
|
adapter srst delay 100
|
|
if {[using_jtag]} {
|
|
jtag_ntrst_delay 100
|
|
}
|
|
|
|
# use hardware reset
|
|
#
|
|
# The STM32H7 does not support connect_assert_srst mode because the AXI is
|
|
# unavailable while SRST is asserted, and that is used to access the DBGMCU
|
|
# component at 0x5C001000 in the examine-end event handler.
|
|
#
|
|
# It is possible to access the DBGMCU component at 0xE00E1000 via AP2 instead
|
|
# of the default AP0, and that works with SRST asserted; however, nonzero AP
|
|
# usage does not work with HLA, so is not done by default. That change could be
|
|
# made in a local configuration file if connect_assert_srst mode is needed for
|
|
# a specific application and a non-HLA adapter is in use.
|
|
reset_config srst_nogate
|
|
|
|
if {![using_hla]} {
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
$_CHIPNAME.cpu0 cortex_m reset_config sysresetreq
|
|
|
|
if {[set $_CHIPNAME.DUAL_CORE]} {
|
|
$_CHIPNAME.cpu1 cortex_m reset_config sysresetreq
|
|
}
|
|
|
|
# Set CSW[27], which according to ARM ADI v5 appendix E1.4 maps to AHB signal
|
|
# HPROT[3], which according to AMBA AHB/ASB/APB specification chapter 3.7.3
|
|
# makes the data access cacheable. This allows reading and writing data in the
|
|
# CPU cache from the debugger, which is far more useful than going straight to
|
|
# RAM when operating on typical variables, and is generally no worse when
|
|
# operating on special memory locations.
|
|
$_CHIPNAME.dap apcsw 0x08000000 0x08000000
|
|
}
|
|
|
|
$_CHIPNAME.cpu0 configure -event examine-end {
|
|
# Enable D3 and D1 DBG clocks
|
|
# DBGMCU_CR |= D3DBGCKEN | D1DBGCKEN
|
|
stm32h7x_dbgmcu_mmw 0x004 0x00600000 0
|
|
|
|
# Enable debug during low power modes (uses more power)
|
|
# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP D1 Domain
|
|
stm32h7x_dbgmcu_mmw 0x004 0x00000007 0
|
|
# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP D2 Domain
|
|
stm32h7x_dbgmcu_mmw 0x004 0x00000038 0
|
|
|
|
# Stop watchdog counters during halt
|
|
# DBGMCU_APB3FZ1 |= WWDG1
|
|
stm32h7x_dbgmcu_mmw 0x034 0x00000040 0
|
|
# DBGMCU_APB1LFZ1 |= WWDG2
|
|
stm32h7x_dbgmcu_mmw 0x03C 0x00000800 0
|
|
# DBGMCU_APB4FZ1 |= WDGLSD1 | WDGLSD2
|
|
stm32h7x_dbgmcu_mmw 0x054 0x000C0000 0
|
|
|
|
# Enable clock for tracing
|
|
# DBGMCU_CR |= TRACECLKEN
|
|
stm32h7x_dbgmcu_mmw 0x004 0x00100000 0
|
|
|
|
# RM0399 (id 0x450) M7+M4 with SWO Funnel
|
|
# RM0433 (id 0x450) M7 with SWO Funnel
|
|
# RM0455 (id 0x480) M7 without SWO Funnel
|
|
# RM0468 (id 0x483) M7 without SWO Funnel
|
|
# Enable CM7 and CM4 slave ports in SWO trace Funnel
|
|
# Works ok also on devices single core and without SWO funnel
|
|
# Hack, use stm32h7x_dbgmcu_mmw with big offset to control SWTF
|
|
# SWTF_CTRL |= ENS0 | ENS1
|
|
stm32h7x_dbgmcu_mmw 0x3000 0x00000003 0
|
|
}
|
|
|
|
$_CHIPNAME.cpu0 configure -event reset-init {
|
|
# Clock after reset is HSI at 64 MHz, no need of PLL
|
|
adapter speed 4000
|
|
}
|
|
|
|
# get _CHIPNAME from current target
|
|
proc stm32h7x_get_chipname {} {
|
|
set t [target current]
|
|
set sep [string last "." $t]
|
|
if {$sep == -1} {
|
|
return $t
|
|
}
|
|
return [string range $t 0 [expr {$sep - 1}]]
|
|
}
|
|
|
|
if {[set $_CHIPNAME.DUAL_CORE]} {
|
|
$_CHIPNAME.cpu1 configure -event examine-end {
|
|
set _CHIPNAME [stm32h7x_get_chipname]
|
|
global $_CHIPNAME.USE_CTI
|
|
|
|
# Stop watchdog counters during halt
|
|
# DBGMCU_APB3FZ2 |= WWDG1
|
|
stm32h7x_dbgmcu_mmw 0x038 0x00000040 0
|
|
# DBGMCU_APB1LFZ2 |= WWDG2
|
|
stm32h7x_dbgmcu_mmw 0x040 0x00000800 0
|
|
# DBGMCU_APB4FZ2 |= WDGLSD1 | WDGLSD2
|
|
stm32h7x_dbgmcu_mmw 0x058 0x000C0000 0
|
|
|
|
if {[set $_CHIPNAME.USE_CTI]} {
|
|
stm32h7x_cti_start
|
|
}
|
|
}
|
|
}
|
|
|
|
# like mrw, but with target selection
|
|
proc stm32h7x_mrw {used_target reg} {
|
|
set value ""
|
|
$used_target mem2array value 32 $reg 1
|
|
return $value(0)
|
|
}
|
|
|
|
# like mmw, but with target selection
|
|
proc stm32h7x_mmw {used_target reg setbits clearbits} {
|
|
set old [stm32h7x_mrw $used_target $reg]
|
|
set new [expr {($old & ~$clearbits) | $setbits}]
|
|
$used_target mww $reg $new
|
|
}
|
|
|
|
# mmw for dbgmcu component registers, it accepts the register offset from dbgmcu base
|
|
# this procedure will use the mem_ap on AP2 whenever possible
|
|
proc stm32h7x_dbgmcu_mmw {reg_offset setbits clearbits} {
|
|
# use $_CHIPNAME.ap2 if possible, and use the proper dbgmcu base address
|
|
if {![using_hla]} {
|
|
set _CHIPNAME [stm32h7x_get_chipname]
|
|
set used_target $_CHIPNAME.ap2
|
|
set reg_addr [expr {0xE00E1000 + $reg_offset}]
|
|
} {
|
|
set used_target [target current]
|
|
set reg_addr [expr {0x5C001000 + $reg_offset}]
|
|
}
|
|
|
|
stm32h7x_mmw $used_target $reg_addr $setbits $clearbits
|
|
}
|
|
|
|
if {[set $_CHIPNAME.USE_CTI]} {
|
|
# create CTI instances for both cores
|
|
cti create $_CHIPNAME.cti0 -dap $_CHIPNAME.dap -ap-num 0 -baseaddr 0xE0043000
|
|
cti create $_CHIPNAME.cti1 -dap $_CHIPNAME.dap -ap-num 3 -baseaddr 0xE0043000
|
|
|
|
$_CHIPNAME.cpu0 configure -event halted { stm32h7x_cti_prepare_restart_all }
|
|
$_CHIPNAME.cpu1 configure -event halted { stm32h7x_cti_prepare_restart_all }
|
|
|
|
$_CHIPNAME.cpu0 configure -event debug-halted { stm32h7x_cti_prepare_restart_all }
|
|
$_CHIPNAME.cpu1 configure -event debug-halted { stm32h7x_cti_prepare_restart_all }
|
|
|
|
proc stm32h7x_cti_start {} {
|
|
set _CHIPNAME [stm32h7x_get_chipname]
|
|
|
|
# Configure Cores' CTIs to halt each other
|
|
# TRIGIN0 (DBGTRIGGER) and TRIGOUT0 (EDBGRQ) at CTM_CHANNEL_0
|
|
$_CHIPNAME.cti0 write INEN0 0x1
|
|
$_CHIPNAME.cti0 write OUTEN0 0x1
|
|
$_CHIPNAME.cti1 write INEN0 0x1
|
|
$_CHIPNAME.cti1 write OUTEN0 0x1
|
|
|
|
# enable CTIs
|
|
$_CHIPNAME.cti0 enable on
|
|
$_CHIPNAME.cti1 enable on
|
|
}
|
|
|
|
proc stm32h7x_cti_stop {} {
|
|
set _CHIPNAME [stm32h7x_get_chipname]
|
|
|
|
$_CHIPNAME.cti0 enable off
|
|
$_CHIPNAME.cti1 enable off
|
|
}
|
|
|
|
proc stm32h7x_cti_prepare_restart_all {} {
|
|
stm32h7x_cti_prepare_restart cti0
|
|
stm32h7x_cti_prepare_restart cti1
|
|
}
|
|
|
|
proc stm32h7x_cti_prepare_restart {cti} {
|
|
set _CHIPNAME [stm32h7x_get_chipname]
|
|
|
|
# Acknowlodge EDBGRQ at TRIGOUT0
|
|
$_CHIPNAME.$cti write INACK 0x01
|
|
$_CHIPNAME.$cti write INACK 0x00
|
|
}
|
|
}
|