107 lines
2.8 KiB
INI
107 lines
2.8 KiB
INI
# script for stm32l4x family
|
|
|
|
#
|
|
# stm32l4 devices support both JTAG and SWD transports.
|
|
#
|
|
source [find target/swj-dp.tcl]
|
|
source [find mem_helper.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME stm32l4x
|
|
}
|
|
|
|
set _ENDIAN little
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# Smallest current target has 64kB ram, use 32kB by default to avoid surprises
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x8000
|
|
}
|
|
|
|
#jtag scan chain
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
if { [using_jtag] } {
|
|
# See STM Document RM0351
|
|
# Section 44.6.3 - corresponds to Cortex-M4 r0p1
|
|
set _CPUTAPID 0x4ba00477
|
|
} {
|
|
set _CPUTAPID 0x2ba01477
|
|
}
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
|
|
if { [info exists BSTAPID] } {
|
|
set _BSTAPID $BSTAPID
|
|
} else {
|
|
# See STM Document RM0351
|
|
# Section 44.6.3
|
|
# STM32L4X6
|
|
set _BSTAPID1 0x06415041
|
|
}
|
|
|
|
if {[using_jtag]} {
|
|
swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1
|
|
}
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME stm32l4x 0 0 0 0 $_TARGETNAME
|
|
|
|
# JTAG speed should be <= F_CPU/6. F_CPU after reset is MSI 4MHz, so use F_JTAG = 500 kHz
|
|
#
|
|
# Since we may be running of an RC oscilator, we crank down the speed a
|
|
# bit more to be on the safe side. Perhaps superstition, but if are
|
|
# running off a crystal, we can run closer to the limit. Note
|
|
# that there can be a pretty wide band where things are more or less stable.
|
|
adapter_khz 500
|
|
|
|
adapter_nsrst_delay 100
|
|
if {[using_jtag]} {
|
|
jtag_ntrst_delay 100
|
|
}
|
|
|
|
reset_config srst_nogate
|
|
|
|
if {![using_hla]} {
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
cortex_m reset_config sysresetreq
|
|
}
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
# CPU comes out of reset with MSI_ON | MSI_RDY | MSI Range 6 (4 MHz).
|
|
# Configure system to use MSI 24 MHz clock, compliant with VOS default (2).
|
|
# 3 WS compliant with VOS=2 and 24 MHz.
|
|
mww 0x40022000 0x00000102 ;# FLASH_ACR = PRFTBE | 3(Latency)
|
|
mww 0x40021000 0x00000099 ;# RCC_CR = MSI_ON | MSIRGSEL| MSI Range 10
|
|
# Boost JTAG frequency
|
|
adapter_khz 4000
|
|
}
|
|
|
|
$_TARGETNAME configure -event examine-end {
|
|
# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
|
|
mmw 0xE0042004 0x00000007 0
|
|
|
|
# Stop watchdog counters during halt
|
|
# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
|
|
mmw 0xE0042008 0x00001800 0
|
|
}
|
|
|
|
$_TARGETNAME configure -event trace-config {
|
|
# Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
|
|
# change this value accordingly to configure trace pins
|
|
# assignment
|
|
mmw 0xE0042004 0x00000020 0
|
|
}
|