142 lines
3.9 KiB
INI
142 lines
3.9 KiB
INI
# script for stm32f4x family
|
|
|
|
#
|
|
# stm32 devices support both JTAG and SWD transports.
|
|
#
|
|
source [find target/swj-dp.tcl]
|
|
source [find mem_helper.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME stm32f4x
|
|
}
|
|
|
|
set _ENDIAN little
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# By default use 32kB (Available RAM in smallest device STM32F410)
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x8000
|
|
}
|
|
|
|
#jtag scan chain
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
if { [using_jtag] } {
|
|
# See STM Document RM0090
|
|
# Section 38.6.3 - corresponds to Cortex-M4 r0p1
|
|
set _CPUTAPID 0x4ba00477
|
|
} {
|
|
set _CPUTAPID 0x2ba01477
|
|
}
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
|
|
|
tpiu create $_CHIPNAME.tpiu -dap stm32f4x.dap -ap-num 0 -baseaddr 0xE0040000
|
|
|
|
if {[using_jtag]} {
|
|
jtag newtap $_CHIPNAME bs -irlen 5
|
|
}
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
|
|
|
|
flash bank $_CHIPNAME.otp stm32f2x 0x1fff7800 0 0 0 $_TARGETNAME
|
|
|
|
if { [info exists QUADSPI] && $QUADSPI } {
|
|
set a [llength [flash list]]
|
|
set _QSPINAME $_CHIPNAME.qspi
|
|
flash bank $_QSPINAME stmqspi 0x90000000 0 0 0 $_TARGETNAME 0xA0001000
|
|
}
|
|
|
|
# JTAG speed should be <= F_CPU/6. F_CPU after reset is 16MHz, so use F_JTAG = 2MHz
|
|
#
|
|
# Since we may be running of an RC oscilator, we crank down the speed a
|
|
# bit more to be on the safe side. Perhaps superstition, but if are
|
|
# running off a crystal, we can run closer to the limit. Note
|
|
# that there can be a pretty wide band where things are more or less stable.
|
|
adapter speed 2000
|
|
|
|
adapter srst delay 100
|
|
if {[using_jtag]} {
|
|
jtag_ntrst_delay 100
|
|
}
|
|
|
|
reset_config srst_nogate
|
|
|
|
if {![using_hla]} {
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
cortex_m reset_config sysresetreq
|
|
}
|
|
|
|
$_TARGETNAME configure -event examine-end {
|
|
# Enable debug during low power modes (uses more power)
|
|
# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
|
|
mmw 0xE0042004 0x00000007 0
|
|
|
|
# Stop watchdog counters during halt
|
|
# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
|
|
mmw 0xE0042008 0x00001800 0
|
|
}
|
|
|
|
proc proc_post_enable {_chipname} {
|
|
targets $_chipname.cpu
|
|
|
|
if { [$_chipname.tpiu cget -protocol] eq "sync" } {
|
|
switch [$_chipname.tpiu cget -port-width] {
|
|
1 {
|
|
mmw 0xE0042004 0x00000060 0x000000c0
|
|
mmw 0x40021020 0x00000000 0x0000ff00
|
|
mmw 0x40021000 0x000000a0 0x000000f0
|
|
mmw 0x40021008 0x000000f0 0x00000000
|
|
}
|
|
2 {
|
|
mmw 0xE0042004 0x000000a0 0x000000c0
|
|
mmw 0x40021020 0x00000000 0x000fff00
|
|
mmw 0x40021000 0x000002a0 0x000003f0
|
|
mmw 0x40021008 0x000003f0 0x00000000
|
|
}
|
|
4 {
|
|
mmw 0xE0042004 0x000000e0 0x000000c0
|
|
mmw 0x40021020 0x00000000 0x0fffff00
|
|
mmw 0x40021000 0x00002aa0 0x00003ff0
|
|
mmw 0x40021008 0x00003ff0 0x00000000
|
|
}
|
|
}
|
|
} else {
|
|
mmw 0xE0042004 0x00000020 0x000000c0
|
|
}
|
|
}
|
|
|
|
$_CHIPNAME.tpiu configure -event post-enable "proc_post_enable $_CHIPNAME"
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
# Configure PLL to boost clock to HSI x 4 (64 MHz)
|
|
mww 0x40023804 0x08012008 ;# RCC_PLLCFGR 16 Mhz /8 (M) * 128 (N) /4(P)
|
|
mww 0x40023C00 0x00000102 ;# FLASH_ACR = PRFTBE | 2(Latency)
|
|
mmw 0x40023800 0x01000000 0 ;# RCC_CR |= PLLON
|
|
sleep 10 ;# Wait for PLL to lock
|
|
mmw 0x40023808 0x00001000 0 ;# RCC_CFGR |= RCC_CFGR_PPRE1_DIV2
|
|
mmw 0x40023808 0x00000002 0 ;# RCC_CFGR |= RCC_CFGR_SW_PLL
|
|
|
|
# Boost JTAG frequency
|
|
adapter speed 8000
|
|
}
|
|
|
|
$_TARGETNAME configure -event reset-start {
|
|
# Reduce speed since CPU speed will slow down to 16MHz with the reset
|
|
adapter speed 2000
|
|
}
|