76 lines
1.7 KiB
INI
76 lines
1.7 KiB
INI
#
|
|
# M0+ devices only have SW-DP, but swj-dp code works, just don't
|
|
# set any jtag related features
|
|
#
|
|
|
|
source [find target/swj-dp.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME stm32l0
|
|
}
|
|
|
|
set _ENDIAN little
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# By default use 8kB (max ram on smallest part)
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x2000
|
|
}
|
|
|
|
# JTAG speed should be <= F_CPU/6.
|
|
# F_CPU after reset is ~2MHz, so use F_JTAG max = 333kHz
|
|
adapter_khz 300
|
|
|
|
adapter_nsrst_delay 100
|
|
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
# Arm, m0+, non-multidrop.
|
|
# http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.faqs/ka16088.html
|
|
set _CPUTAPID 0x0bc11477
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -expected-id $_CPUTAPID
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
# flash size will be probed
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME stm32lx 0x08000000 0 0 0 $_TARGETNAME
|
|
|
|
if {![using_hla]} {
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
cortex_m reset_config sysresetreq
|
|
}
|
|
|
|
proc stm32l0_enable_HSI16 {} {
|
|
# Enable HSI16 as clock source
|
|
echo "STM32L0: Enabling HSI16"
|
|
|
|
# Set HSI16ON in RCC_CR (leave MSI enabled)
|
|
mww 0x40021000 0x00000101
|
|
|
|
# Set HSI16 as SYSCLK (RCC_CFGR)
|
|
mww 0x4002100c 0x00000001
|
|
|
|
# Increase speed
|
|
adapter_khz 2500
|
|
}
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
stm32l0_enable_HSI16
|
|
}
|
|
|
|
$_TARGETNAME configure -event reset-start {
|
|
adapter_khz 300
|
|
}
|