75 lines
2.1 KiB
INI
75 lines
2.1 KiB
INI
# Hitex STR9-comStick
|
|
# http://www.hitex.com/index.php?id=383
|
|
# This works for the STR9-comStick revisions STR912CS-A1 and STR912CS-A2.
|
|
|
|
source [find interface/hitex_str9-comstick.cfg]
|
|
|
|
# set jtag speed
|
|
jtag_khz 3000
|
|
|
|
jtag_nsrst_delay 100
|
|
jtag_ntrst_delay 100
|
|
#use combined on interfaces or targets that can't set TRST/SRST separately
|
|
reset_config trst_and_srst
|
|
#jtag scan chain
|
|
#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME str912
|
|
}
|
|
|
|
if { [info exists ENDIAN] } {
|
|
set _ENDIAN $ENDIAN
|
|
} else {
|
|
set _ENDIAN little
|
|
}
|
|
|
|
if { [info exists FLASHTAPID ] } {
|
|
set _FLASHTAPID $FLASHTAPID
|
|
} else {
|
|
set _FLASHTAPID 0x04570041
|
|
}
|
|
jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 -expected-id $_FLASHTAPID
|
|
|
|
if { [info exists CPUTAPID ] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
set _CPUTAPID 0x25966041
|
|
}
|
|
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
|
|
if { [info exists BSTAPID ] } {
|
|
set _BSTAPID $BSTAPID
|
|
} else {
|
|
# Found on STR9-comStick, revision STR912CS-A1
|
|
set _BSTAPID1 0x1457f041
|
|
# Found on STR9-comStick, revision STR912CS-A2
|
|
set _BSTAPID2 0x2457f041
|
|
}
|
|
jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID1 -expected-id $_BSTAPID2
|
|
|
|
set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
|
|
target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
# We can increase speed now that we know the target is halted.
|
|
#jtag_rclk 3000
|
|
|
|
# -- Enable 96K RAM
|
|
# PFQBC enabled / DTCM & AHB wait-states disabled
|
|
mww 0x5C002034 0x0191
|
|
|
|
str9x flash_config 0 4 2 0 0x80000
|
|
flash protect 0 0 7 off
|
|
}
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0
|
|
|
|
#flash bank <driver> <base> <size> <chip_width> <bus_width>
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME str9x 0x00000000 0x00080000 0 0 0
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME str9x 0x00080000 0x00008000 0 0 0
|