172 lines
5.4 KiB
INI
172 lines
5.4 KiB
INI
# The Atheros AR9331 is a highly integrated and cost effective
|
|
# IEEE 802.11n 1x1 2.4 GHz System- on-a-Chip (SoC) for wireless
|
|
# local area network (WLAN) AP and router platforms.
|
|
#
|
|
# Notes:
|
|
# - MIPS Processor ID (PRId): 0x00019374
|
|
# - 24Kc MIPS processor with 64 KB I-Cache and 32 KB D-Cache,
|
|
# operating at up to 400 MHz
|
|
# - External 16-bit DDR1, DDR2, or SDRAM memory interface
|
|
# - TRST is not available.
|
|
# - EJTAG PrRst signal is not supported
|
|
# - RESET_L pin A72 on the SoC will reset internal JTAG logic.
|
|
#
|
|
|
|
# Pins related for debug and bootstrap:
|
|
# Name Pin Description
|
|
# JTAG
|
|
# JTAG_TCK GPIO0, (A27) Software configurable, default JTAG
|
|
# JTAG_TDI GPIO6, (B46) Software configurable, default JTAG
|
|
# JTAG_TDO GPIO7, (A54) Software configurable, default JTAG
|
|
# JTAG_TMS GPIO8, (A52) Software configurable, default JTAG
|
|
# Reset
|
|
# RESET_L -, (A72) Input only
|
|
# SYS_RST_L ???????? Output reset request or GPIO
|
|
# Bootstrap
|
|
# MEM_TYPE[1] GPIO28, (A74) 0 - SDRAM, 1 - DDR1 RAM, 2 - DDR2 RAM
|
|
# MEM_TYPE[0] GPIO12, (A56)
|
|
# FW_DOWNLOAD GPIO16, (A75) Used if BOOT_FROM_SPI = 0. 0 - boot from USB
|
|
# 1 - boot from MDIO.
|
|
# JTAG_MODE(JS) GPIO11, (B48) 0 - JTAG (Default); 1 - EJTAG
|
|
# BOOT_FROM_SPI GPIO1, (A77) 0 - ROM boot; 1 - SPI boot
|
|
# SEL_25M_40M GPIO0, (A78) 0 - 25MHz; 1 - 40MHz
|
|
# UART
|
|
# UART0_SOUT GPIO10, (A79)
|
|
# UART0_SIN GPIO9, (B68)
|
|
|
|
# Per default we need to use "none" variant to be able properly "reset init"
|
|
# or "reset halt" the CPU.
|
|
reset_config none srst_pulls_trst
|
|
|
|
# For SRST based variant we still need proper timings.
|
|
# For ETH part the reset should be asserted at least for 10ms
|
|
# Since there is no other information let's take 100ms to be sure.
|
|
adapter srst pulse_width 100
|
|
|
|
# according to the SoC documentation it should take at least 5ms from
|
|
# reset end till bootstrap end. In the practice we need 8ms to get JTAG back
|
|
# to live.
|
|
adapter srst delay 8
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $_CHIPNAME
|
|
} else {
|
|
set _CHIPNAME ar9331
|
|
}
|
|
|
|
jtag newtap $_CHIPNAME cpu -irlen 5 -expected-id 0x00000001
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME mips_m4k -endian big -chain-position $_TARGETNAME
|
|
|
|
# provide watchdog helper.
|
|
proc disable_watchdog { } {
|
|
mww 0xb8060008 0x0
|
|
}
|
|
|
|
$_TARGETNAME configure -event halted { disable_watchdog }
|
|
|
|
# Since PrRst is not supported and SRST will reset complete chip
|
|
# with JTAG engine, we need to reset CPU from CPU itself.
|
|
$_TARGETNAME configure -event reset-assert-pre {
|
|
halt
|
|
}
|
|
|
|
$_TARGETNAME configure -event reset-assert {
|
|
catch "mww 0xb806001C 0x01000000"
|
|
}
|
|
|
|
# To be able to trigger complete chip reset, in case JTAG is blocked
|
|
# or CPU not responding, we still can use this helper.
|
|
proc full_reset { } {
|
|
reset_config srst_only
|
|
reset
|
|
halt
|
|
reset_config none
|
|
}
|
|
|
|
proc disable_watchdog { } {
|
|
;# disable watchdog
|
|
mww 0xb8060008 0x0
|
|
}
|
|
|
|
$_TARGETNAME configure -event reset-end { disable_watchdog }
|
|
|
|
# Section with helpers which can be used by boards
|
|
proc ar9331_25mhz_pll_init {} {
|
|
mww 0xb8050008 0x00018004 ;# bypass PLL; AHB_POST_DIV - ratio 4
|
|
mww 0xb8050004 0x00000352 ;# 34000(ns)/40ns(25MHz) = 0x352 (850)
|
|
mww 0xb8050000 0x40818000 ;# Power down control for CPU PLL
|
|
;# OUTDIV | REFDIV | DIV_INT
|
|
mww 0xb8050010 0x001003e8 ;# CPU PLL Dither FRAC Register
|
|
;# (disabled?)
|
|
mww 0xb8050000 0x00818000 ;# Power on | OUTDIV | REFDIV | DIV_INT
|
|
mww 0xb8050008 0x00008000 ;# remove bypass;
|
|
;# AHB_POST_DIV - ratio 2
|
|
}
|
|
|
|
proc ar9331_ddr1_init {} {
|
|
mww 0xb8000000 0x7fbc8cd0 ;# DDR_CONFIG - lots of DRAM confs
|
|
mww 0xb8000004 0x9dd0e6a8 ;# DDR_CONFIG2 - more DRAM confs
|
|
|
|
mww 0xb8000010 0x8 ;# Forces a PRECHARGE ALL cycle
|
|
mww 0xb8000008 0x133 ;# mode reg: 0x133 - default
|
|
mww 0xb8000010 0x1 ;# Forces an MRS update cycl
|
|
mww 0xb800000c 0x2 ;# Extended mode register value.
|
|
;# default 0x2 - Reset to weak driver, DLL on
|
|
mww 0xb8000010 0x2 ;# Forces an EMRS update cycle
|
|
mww 0xb8000010 0x8 ;# Forces a PRECHARGE ALL cycle
|
|
mww 0xb8000008 0x33 ;# mode reg: remove some bit?
|
|
mww 0xb8000010 0x1 ;# Forces an MRS update cycl
|
|
mww 0xb8000014 0x4186 ;# enable refres: bit(14) - set refresh rate
|
|
mww 0xb800001c 0x8 ;# This register is used along with DQ Lane 0,
|
|
;# DQ[7:0], DQS_0
|
|
mww 0xb8000020 0x9 ;# This register is used along with DQ Lane 1,
|
|
;# DQ[15:8], DQS_1.
|
|
mww 0xb8000018 0xff ;# DDR read and capture bit mask.
|
|
;# Each bit represents a cycle of valid data.
|
|
}
|
|
|
|
proc ar9331_ddr2_init {} {
|
|
mww 0xb8000000 0x7fbc8cd0 ;# DDR_CONFIG - lots of DRAM confs
|
|
mww 0xb8000004 0x9dd0e6a8 ;# DDR_CONFIG2 - more DRAM confs
|
|
|
|
mww 0xb800008c 0x00000a59
|
|
mww 0xb8000010 0x00000008 ;# PRECHARGE ALL cycle
|
|
|
|
mww 0xb8000090 0x00000000
|
|
mww 0xb8000010 0x00000010 ;# EMR2S update cycle
|
|
|
|
mww 0xb8000094 0x00000000
|
|
mww 0xb8000010 0x00000020 ;# EMR3S update cycle
|
|
|
|
mww 0xb800000c 0x00000000
|
|
mww 0xb8000010 0x00000002 ;# EMRS update cycle
|
|
|
|
mww 0xb8000008 0x00000100
|
|
mww 0xb8000010 0x00000001 ;# MRS update cycle
|
|
|
|
mww 0xb8000010 0x00000008 ;# PRECHARGE ALL cycle
|
|
|
|
mww 0xb8000010 0x00000004
|
|
mww 0xb8000010 0x00000004 ;# AUTO REFRESH cycle
|
|
|
|
mww 0xb8000008 0x00000a33
|
|
mww 0xb8000010 0x00000001 ;# MRS update cycle
|
|
|
|
mww 0xb800000c 0x00000382
|
|
mww 0xb8000010 0x00000002 ;# EMRS update cycle
|
|
|
|
mww 0xb800000c 0x00000402
|
|
mww 0xb8000010 0x00000002 ;# EMRS update cycle
|
|
|
|
mww 0xb8000014 0x00004186 ;# DDR_REFRESH
|
|
mww 0xb800001c 0x00000008 ;# DDR_TAP_CTRL0
|
|
mww 0xb8000020 0x00000009 ;# DDR_TAP_CTRL1
|
|
|
|
;# DDR read and capture bit mask.
|
|
;# Each bit represents a cycle of valid data.
|
|
;# 0xff: use 16-bit DDR
|
|
mww 0xb8000018 0x000000ff
|
|
}
|