59 lines
2.0 KiB
INI
59 lines
2.0 KiB
INI
# SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
# This is an STM32L476G discovery board with a single STM32L476VGT6 chip.
|
|
# http://www.st.com/en/evaluation-tools/32l476gdiscovery.html
|
|
|
|
# This is for using the onboard STLINK
|
|
source [find interface/stlink.cfg]
|
|
|
|
transport select dapdirect_swd
|
|
|
|
# increase working area to 96KB
|
|
set WORKAREASIZE 0x18000
|
|
|
|
# enable stmqspi
|
|
set QUADSPI 1
|
|
|
|
source [find target/stm32l4x.cfg]
|
|
|
|
# QUADSPI initialization
|
|
proc qspi_init { } {
|
|
global a
|
|
mmw 0x4002104C 0x000001FF 0 ;# RCC_AHB2ENR |= GPIOAEN-GPIOIEN (enable clocks)
|
|
mmw 0x40021050 0x00000100 0 ;# RCC_AHB3ENR |= QSPIEN (enable clock)
|
|
sleep 1 ;# Wait for clock startup
|
|
|
|
# PE11: NCS, PE10: CLK, PE15: BK1_IO3, PE14: BK1_IO2, PE13: BK1_IO1, PE12: BK1_IO0
|
|
|
|
# PE15:AF10:V, PE14:AF10:V, PE13:AF10:V, PE12:AF10:V, PE11:AF10:V, PE10:AF10:V
|
|
|
|
# Port E: PE15:AF10:V, PE14:AF10:V, PE13:AF10:V, PE12:AF10:V, PE11:AF10:V, PE10:AF10:V
|
|
mmw 0x48001000 0xAAA00000 0x55500000 ;# MODER
|
|
mmw 0x48001008 0xFFF00000 0x00000000 ;# OSPEEDR
|
|
mmw 0x48001024 0xAAAAAA00 0x55555500 ;# AFRH
|
|
|
|
mww 0xA0001030 0x00001000 ;# QUADSPI_LPTR: deactivate CS after 4096 clocks when FIFO is full
|
|
mww 0xA0001000 0x01500008 ;# QUADSPI_CR: PRESCALER=1, APMS=1, FTHRES=0, FSEL=0, DFM=0, SSHIFT=0, TCEN=1
|
|
mww 0xA0001004 0x00170100 ;# QUADSPI_DCR: FSIZE=0x17, CSHT=0x01, CKMODE=0
|
|
mmw 0xA0001000 0x00000001 0 ;# QUADSPI_CR: EN=1
|
|
|
|
# memory-mapped read mode with 3-byte addresses
|
|
mww 0xA0001014 0x0D002503 ;# QUADSPI_CCR: FMODE=0x3, DMODE=0x1, DCYC=0x0, ADSIZE=0x2, ADMODE=0x1, IMODE=0x1, INSTR=READ
|
|
}
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
mmw 0x40022000 0x00000004 0x00000003 ;# 4 WS for 72 MHz HCLK
|
|
sleep 1
|
|
mmw 0x40021000 0x00000100 0x00000000 ;# HSI on
|
|
mww 0x4002100C 0x01002432 ;# 72 MHz: PLLREN=1, PLLM=4, PLLN=36, PLLR=2, HSI
|
|
mww 0x40021008 0x00008001 ;# always HSI, APB1: /1, APB2: /1
|
|
mmw 0x40021000 0x01000000 0x00000000 ;# PLL on
|
|
sleep 1
|
|
mmw 0x40021008 0x00000003 0x00000000 ;# switch to PLL
|
|
sleep 1
|
|
|
|
adapter speed 4000
|
|
|
|
qspi_init
|
|
}
|