68 lines
2.3 KiB
INI
68 lines
2.3 KiB
INI
# SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
# This is an STM32F469I discovery board with a single STM32F469NIH6 chip.
|
|
# http://www.st.com/en/evaluation-tools/32f469idiscovery.html
|
|
|
|
# This is for using the onboard STLINK
|
|
source [find interface/stlink.cfg]
|
|
|
|
transport select dapdirect_swd
|
|
|
|
# increase working area to 128KB
|
|
set WORKAREASIZE 0x20000
|
|
|
|
# enable stmqspi
|
|
set QUADSPI 1
|
|
|
|
source [find target/stm32f4x.cfg]
|
|
|
|
# QUADSPI initialization
|
|
proc qspi_init { } {
|
|
global a
|
|
mmw 0x40023830 0x000007FF 0 ;# RCC_AHB1ENR |= GPIOAEN-GPIOKEN (enable clocks)
|
|
mmw 0x40023838 0x00000002 0 ;# RCC_AHB3ENR |= QSPIEN (enable clock)
|
|
sleep 1 ;# Wait for clock startup
|
|
|
|
# PF10: CLK, PB06: BK1_NCS, PF06: BK1_IO3, PF07: BK1_IO2, PF09: BK1_IO1, PF08: BK1_IO0
|
|
|
|
# PB06:AF10:V, PF10:AF09:V, PF09:AF10:V, PF08:AF10:V, PF07:AF09:V, PF06:AF09:V
|
|
|
|
# Port B: PB06:AF10:V
|
|
mmw 0x40020400 0x00002000 0x00001000 ;# MODER
|
|
mmw 0x40020408 0x00003000 0x00000000 ;# OSPEEDR
|
|
mmw 0x40020420 0x0A000000 0x05000000 ;# AFRL
|
|
|
|
# Port F: PF10:AF09:V, PF09:AF10:V, PF08:AF10:V, PF07:AF09:V, PF06:AF09:V
|
|
mmw 0x40021400 0x002AA000 0x00155000 ;# MODER
|
|
mmw 0x40021408 0x003FF000 0x00000000 ;# OSPEEDR
|
|
mmw 0x40021420 0x99000000 0x66000000 ;# AFRL
|
|
mmw 0x40021424 0x000009AA 0x00000655 ;# AFRH
|
|
|
|
mww 0xA0001030 0x00001000 ;# QUADSPI_LPTR: deactivate CS after 4096 clocks when FIFO is full
|
|
mww 0xA0001000 0x03500008 ;# QUADSPI_CR: PRESCALER=3, APMS=1, FTHRES=0, FSEL=0, DFM=0, SSHIFT=0, TCEN=1
|
|
mww 0xA0001004 0x00170100 ;# QUADSPI_DCR: FSIZE=0x17, CSHT=0x01, CKMODE=0
|
|
mmw 0xA0001000 0x00000001 0 ;# QUADSPI_CR: EN=1
|
|
|
|
# 1-line spi mode
|
|
mww 0xA0001014 0x000003F5 ;# QUADSPI_CCR: FMODE=0x0, DMODE=0x0, DCYC=0x0, ADSIZE=0x0, ADMODE=0x0, IMODE=0x3, INSTR=RSTQIO
|
|
sleep 1
|
|
|
|
# memory-mapped read mode with 3-byte addresses
|
|
mww 0xA0001014 0x0D002503 ;# QUADSPI_CCR: FMODE=0x3, DMODE=0x1, DCYC=0x0, ADSIZE=0x2, ADMODE=0x1, IMODE=0x1, INSTR=READ
|
|
}
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
mww 0x40023C00 0x00000005 ;# 5 WS for 160 MHz HCLK
|
|
sleep 1
|
|
mww 0x40023804 0x24002808 ;# 160 MHz: HSI, PLLM=8, PLLN=160, PLLP=2
|
|
mww 0x40023808 0x00009400 ;# APB1: /4, APB2: /2
|
|
mmw 0x40023800 0x01000000 0x00000000 ;# PLL on
|
|
sleep 1
|
|
mmw 0x40023808 0x00000002 0x00000000 ;# switch to PLL
|
|
sleep 1
|
|
|
|
adapter speed 4000
|
|
|
|
qspi_init
|
|
}
|