148 lines
3.7 KiB
INI
148 lines
3.7 KiB
INI
# SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
# DM365 EVM board -- Beta
|
|
# http://focus.ti.com/docs/toolsw/folders/print/tmdxevm365.html
|
|
# http://support.spectrumdigital.com/boards/evmdm365
|
|
|
|
source [find target/ti_dm365.cfg]
|
|
|
|
# NOTE: in Rev C boards, the CPLD ignores SRST from the ARM-20 JTAG
|
|
# connector, so it doesn't affect generation of the reset signal.
|
|
# Accordingly, resets require something else. ICEpick could do it;
|
|
# but its docs aren't generally available.
|
|
#
|
|
# At this writing, newer boards aren't available ... so assume no SRST.
|
|
# Also ICEpick docs aren't available ... so we must use watchdog reset,
|
|
# and hope the CPU isn't wedged or in a WFI loop (either of which can
|
|
# block access to CPU and thus watchdog registers).
|
|
|
|
reset_config trst_only
|
|
$_TARGETNAME configure -event reset-assert "davinci_wdog_reset"
|
|
|
|
# SW5.1 routes CS0: NAND vs OneNAND.
|
|
# SW4.6:4 controls AEMIF width (8 for NAND, 16 for OneNand)
|
|
# for boot-from-flash, those must agree with SW4.3:1 settings.
|
|
|
|
if { [info exists CS0MODE] } {
|
|
# NAND or OneNAND
|
|
set CS0 $CS0MODE
|
|
} else {
|
|
set CS0 ""
|
|
echo "WARNING: CS0 configuration not known"
|
|
proc cs0_setup {a_emif} {}
|
|
proc flashprobe {} {}
|
|
}
|
|
|
|
set a_emif [dict get $dm365 a_emif]
|
|
|
|
# As shipped: boot from NAND.
|
|
if { $CS0 == "NAND" } {
|
|
echo "CS0 NAND"
|
|
|
|
# NAND socket has two chipselects. Default MT29F16G08FAA chip
|
|
# has 1GByte on each one.
|
|
# NOTE: "hwecc4" here presumes that you're not updating anything
|
|
# that needs infix layout (e.g. UBL, old U-Boot, etc)
|
|
nand device low davinci $_TARGETNAME 0x02000000 hwecc4 $a_emif
|
|
nand device high davinci $_TARGETNAME 0x02004000 hwecc4 $a_emif
|
|
|
|
proc cs0_setup {a_emif} {
|
|
global dm365
|
|
|
|
# 8 bit EMIF
|
|
davinci_pinmux $dm365 2 0x00000016
|
|
|
|
# slow/pessimistic timings
|
|
set nand_timings 0x40400204
|
|
# fast (25% faster page reads)
|
|
#set nand_timings 0x0400008c
|
|
|
|
# CS0 == socketed NAND (default MT29F16G08FAA, 2 GBytes)
|
|
mww [expr {$a_emif + 0x10}] $nand_timings
|
|
|
|
# NANDFCR -- CS0 has NAND
|
|
mww [expr {$a_emif + 0x60}] 0x01
|
|
}
|
|
proc flashprobe {} {
|
|
nand probe 0
|
|
nand probe 1
|
|
}
|
|
|
|
} elseif { $CS0 == "OneNAND" } {
|
|
echo "CS0 OneNAND"
|
|
|
|
# No support for this OneNAND in OpenOCD (yet) or Linux ...
|
|
# REVISIT OneNAND timings not verified to work!
|
|
echo "WARNING -- OneNAND not yet tested!"
|
|
|
|
proc cs0_setup {a_emif} {
|
|
global dm365
|
|
|
|
# 16 bit EMIF
|
|
davinci_pinmux $dm365 2 0x00000055
|
|
|
|
# CS0 == OneNAND (KFG1G16U2B-DIB6, 128 KBytes)
|
|
mww [expr {$a_emif + 0x10}] 0x00000001
|
|
|
|
# ONENANDCTRL -- CS0 has OneNAND, enable sync reads
|
|
mww [expr {$a_emif + 0x5c}] 0x0441
|
|
}
|
|
proc flashprobe {} { }
|
|
}
|
|
|
|
# NOTE: disable or replace this call to dm365evm_init if you're
|
|
# debugging new UBL/NANDboot code from SRAM.
|
|
$_TARGETNAME configure -event reset-init { dm365evm_init }
|
|
|
|
#
|
|
# This post-reset init is called when the MMU isn't active, all IRQs
|
|
# are disabled, etc. It should do most of what a UBL does, except for
|
|
# loading code (like U-Boot) into DRAM and running it.
|
|
#
|
|
proc dm365evm_init {} {
|
|
global dm365
|
|
|
|
echo "Initialize DM365 EVM board"
|
|
|
|
# CLKIN = 24 MHz ... can't talk quickly to ARM yet
|
|
adapter speed 1500
|
|
|
|
# FIXME -- PLL init
|
|
|
|
########################
|
|
# PINMUX setup
|
|
|
|
davinci_pinmux $dm365 0 0x00fd0000
|
|
davinci_pinmux $dm365 1 0x00145555
|
|
# mux2 controls AEMIF ... 8 bit for NAND, 16 for OneNand
|
|
davinci_pinmux $dm365 3 0x375affff
|
|
davinci_pinmux $dm365 4 0x55556555
|
|
|
|
########################
|
|
# PSC setup (minimal)
|
|
|
|
# DDR EMIF/13, AEMIF/14, UART0/19
|
|
psc_enable 13
|
|
psc_enable 14
|
|
psc_enable 19
|
|
psc_go
|
|
|
|
# FIXME setup DDR2 (needs PLL)
|
|
|
|
########################
|
|
# ASYNC EMIF
|
|
|
|
set a_emif [dict get $dm365 a_emif]
|
|
|
|
# AWCCR
|
|
mww [expr {$a_emif + 0x04}] 0xff
|
|
# CS0 == NAND or OneNAND
|
|
cs0_setup $a_emif
|
|
# CS1 == CPLD
|
|
mww [expr {$a_emif + 0x14}] 0x00a00505
|
|
|
|
# FIXME setup UART0
|
|
|
|
flashprobe
|
|
}
|