72 lines
1.8 KiB
INI
72 lines
1.8 KiB
INI
# SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
source [find target/alphascale_asm9260t.cfg]
|
|
|
|
reset_config trst_and_srst
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
echo "Configure clock"
|
|
# Enable SRAM clk
|
|
mww 0x80040024 0x4
|
|
# Enable IRQ clk
|
|
mww 0x80040034 0x100
|
|
# Enable DMA0,1 clk
|
|
mww 0x80040024 0x600
|
|
# Make sysre syspll is enabled
|
|
mww 0x80040238 0x750
|
|
#CPU = PLLCLK/2
|
|
mww 0x8004017C 0x2
|
|
#SYSAHBCLK = CPUCLK/2
|
|
mww 0x80040180 0x2
|
|
# Set PLL freq to 480MHz
|
|
mww 0x80040100 480
|
|
# normally we shoul waiting here until we get 0x1 (0x80040104)&0x1)==0x0)
|
|
sleep 100
|
|
|
|
# select PLL as main source
|
|
mww 0x80040120 0x1
|
|
# disable and enable main clk to update changes?
|
|
mww 0x80040124 0x0
|
|
mww 0x80040124 0x1
|
|
|
|
echo "Configure memory"
|
|
#enable EMI CLK
|
|
mww 0x80040024 0x40
|
|
|
|
# configure memory controller for internal SRAM
|
|
mww 0x80700000 0x1188
|
|
# change default emi clk delay
|
|
mww 0x8004034C 0xA0503
|
|
# make sure chip_select_register2_low has correct value (why?)
|
|
mww 0x8070001c 0x20000000
|
|
# set type to sdram and size to 32MB
|
|
mww 0x8070005c 0xa
|
|
# configure internal SDRAM timing
|
|
mww 0x80700004 0x024996d9
|
|
# configure Static Memory timing
|
|
mww 0x80700094 0x00542b4f
|
|
|
|
echo "Configure uart4"
|
|
# enable pinctrl clk
|
|
mww 0x80040024 0x2000000
|
|
# mux GPIO3_0 and GPIO3_1 to UART4
|
|
mww 0x80044060 0x2
|
|
mww 0x80044064 0x2
|
|
# configure UART4CLKDIV
|
|
mww 0x800401a8 0x1
|
|
# enable uart4 clk
|
|
mww 0x80040024 0x8000
|
|
# clear softrst and clkgate on uart4
|
|
mww 0x80010008 0xC0000000
|
|
# set bandrate 115200 12M
|
|
mww 0x80010030 0x00062070
|
|
# enable Rx&Tx
|
|
mww 0x80010024 0x301
|
|
# clear hw control
|
|
mww 0x80010028 0xc000
|
|
}
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x21ffe000 -work-area-virt 0xc1ffe000 -work-area-size 0x1000
|
|
$_TARGETNAME arm7_9 fast_memory_access enable
|
|
$_TARGETNAME arm7_9 dcc_downloads enable
|