155 lines
4.2 KiB
INI
155 lines
4.2 KiB
INI
# SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
# common script for stm32l5x and stm32u5x families
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# By default use 64kB
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x10000
|
|
}
|
|
|
|
#jtag scan chain
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
if { [using_jtag] } {
|
|
# STM32L5x: RM0438 Rev5, Section 52.2.8 JTAG debug port - Table 425. JTAG-DP data registers
|
|
# STM32U5x: RM0456 Rev1, Section 65.2.8 JTAG debug port - Table 661. JTAG-DP data registers
|
|
# Corresponds to Cortex®-M33 JTAG debug port ID code
|
|
set _CPUTAPID 0x0ba04477
|
|
} {
|
|
# SWD IDCODE (single drop, arm)
|
|
set _CPUTAPID 0x0be12477
|
|
}
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
|
|
|
if {[using_jtag]} {
|
|
jtag newtap $_CHIPNAME bs -irlen 5
|
|
}
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -endian little -dap $_CHIPNAME.dap
|
|
|
|
# use non-secure RAM by default
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
# create sec/ns flash and otp memories (sizes will be probed)
|
|
flash bank $_CHIPNAME.flash_ns stm32l4x 0x08000000 0 0 0 $_TARGETNAME
|
|
flash bank $_CHIPNAME.flash_alias_s stm32l4x 0x0C000000 0 0 0 $_TARGETNAME
|
|
flash bank $_CHIPNAME.otp stm32l4x 0x0BFA0000 0 0 0 $_TARGETNAME
|
|
|
|
# Common knowledge tells JTAG speed should be <= F_CPU/6.
|
|
# F_CPU after reset is MSI 4MHz, so use F_JTAG = 500 kHz to stay on
|
|
# the safe side.
|
|
#
|
|
# Note that there is a pretty wide band where things are
|
|
# more or less stable, see http://review.openocd.org/3366
|
|
adapter speed 500
|
|
|
|
adapter srst delay 100
|
|
if {[using_jtag]} {
|
|
jtag_ntrst_delay 100
|
|
}
|
|
|
|
reset_config srst_nogate
|
|
|
|
if {![using_hla]} {
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
cortex_m reset_config sysresetreq
|
|
}
|
|
|
|
proc stm32x5x_is_secure {} {
|
|
# read Debug Security Control and Status Register (DSCSR) and check CDS (bit 16)
|
|
set DSCSR [mrw 0xE000EE08]
|
|
return [expr {($DSCSR & (1 << 16)) != 0}]
|
|
}
|
|
|
|
proc stm32x5x_ahb_ap_non_secure_access {} {
|
|
# SPROT=1=Non Secure access, Priv=1
|
|
[[target current] cget -dap] apcsw 0x4B000000 0x4F000000
|
|
}
|
|
|
|
proc stm32x5x_ahb_ap_secure_access {} {
|
|
# SPROT=0=Secure access, Priv=1
|
|
[[target current] cget -dap] apcsw 0x0B000000 0x4F000000
|
|
}
|
|
|
|
$_TARGETNAME configure -event reset-start {
|
|
# Reset clock is MSI (4 MHz)
|
|
adapter speed 480
|
|
}
|
|
|
|
$_TARGETNAME configure -event examine-end {
|
|
# DBGMCU_CR |= DBG_STANDBY | DBG_STOP
|
|
mmw 0xE0044004 0x00000006 0
|
|
|
|
# Stop watchdog counters during halt
|
|
# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
|
|
mmw 0xE0044008 0x00001800 0
|
|
}
|
|
|
|
$_TARGETNAME configure -event halted {
|
|
set secure [stm32x5x_is_secure]
|
|
|
|
if {$secure} {
|
|
set secure_str "Secure"
|
|
stm32x5x_ahb_ap_secure_access
|
|
} else {
|
|
set secure_str "Non-Secure"
|
|
stm32x5x_ahb_ap_non_secure_access
|
|
}
|
|
|
|
# print the secure state only when it changes
|
|
set _TARGETNAME [target current]
|
|
global $_TARGETNAME.secure
|
|
|
|
if {![info exists $_TARGETNAME.secure] || $secure != [set $_TARGETNAME.secure]} {
|
|
echo "CPU in $secure_str state"
|
|
# update saved security state
|
|
set $_TARGETNAME.secure $secure
|
|
}
|
|
}
|
|
|
|
$_TARGETNAME configure -event gdb-flash-erase-start {
|
|
set use_secure_workarea 0
|
|
# check if FLASH_OPTR.TZEN is enabled
|
|
set FLASH_OPTR [mrw 0x40022040]
|
|
if {[expr {$FLASH_OPTR & 0x80000000}] == 0} {
|
|
echo "TZEN option bit disabled"
|
|
stm32x5x_ahb_ap_non_secure_access
|
|
} else {
|
|
stm32x5x_ahb_ap_secure_access
|
|
echo "TZEN option bit enabled"
|
|
|
|
# check if FLASH_OPTR.RDP is not Level 0.5
|
|
if {[expr {$FLASH_OPTR & 0xFF}] != 0x55} {
|
|
set use_secure_workarea 1
|
|
}
|
|
}
|
|
|
|
set _TARGETNAME [target current]
|
|
set workarea_addr [$_TARGETNAME cget -work-area-phys]
|
|
echo "workarea_addr $workarea_addr"
|
|
|
|
if {$use_secure_workarea} {
|
|
set workarea_addr [expr {$workarea_addr | 0x10000000}]
|
|
} else {
|
|
set workarea_addr [expr {$workarea_addr & ~0x10000000}]
|
|
}
|
|
|
|
$_TARGETNAME configure -work-area-phys $workarea_addr
|
|
}
|
|
|
|
$_TARGETNAME configure -event trace-config {
|
|
# Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
|
|
# change this value accordingly to configure trace pins
|
|
# assignment
|
|
mmw 0xE0044004 0x00000020 0
|
|
}
|