122 lines
4.6 KiB
INI
122 lines
4.6 KiB
INI
# STMicroelectronics STM32MP15x (Single/Dual Cortex-A7 plus Cortex-M4)
|
|
# http://www.st.com/stm32mp1
|
|
|
|
# HLA does not support multi-cores nor custom CSW nor AP other than 0
|
|
if { [using_hla] } {
|
|
echo "ERROR: HLA transport cannot work with this target."
|
|
echo "ERROR: To use STLink switch to DAP mode, as in \"board/stm32mp15x_dk2.cfg\"."
|
|
shutdown
|
|
}
|
|
|
|
source [find target/swj-dp.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME stm32mp15x
|
|
}
|
|
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
if { [using_jtag] } {
|
|
set _CPUTAPID 0x6ba00477
|
|
} else {
|
|
set _CPUTAPID 0x6ba02477
|
|
}
|
|
}
|
|
|
|
# Chip Level TAP Controller, only in jtag mode
|
|
if { [info exists CLCTAPID] } {
|
|
set _CLCTAPID $CLCTAPID
|
|
} else {
|
|
set _CLCTAPID 0x06500041
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME tap -expected-id $_CPUTAPID -irlen 4
|
|
if { [using_jtag] } {
|
|
jtag newtap $_CHIPNAME.clc tap -expected-id $_CLCTAPID -irlen 5
|
|
}
|
|
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.tap -ignore-syspwrupack
|
|
|
|
# FIXME: Cortex-M code requires target accessible during reset, but this is not possible in STM32MP1
|
|
# so defer-examine it until the reset framework get merged
|
|
# NOTE: keep ap-num and dbgbase to speed-up examine after reset
|
|
# NOTE: do not change the order of target create
|
|
target create $_CHIPNAME.ap1 mem_ap -dap $_CHIPNAME.dap -ap-num 1
|
|
target create $_CHIPNAME.ap2 mem_ap -dap $_CHIPNAME.dap -ap-num 2
|
|
target create $_CHIPNAME.axi mem_ap -dap $_CHIPNAME.dap -ap-num 0
|
|
target create $_CHIPNAME.cpu0 cortex_a -dap $_CHIPNAME.dap -ap-num 1 -coreid 0 -dbgbase 0xE00D0000
|
|
target create $_CHIPNAME.cpu1 cortex_a -dap $_CHIPNAME.dap -ap-num 1 -coreid 1 -dbgbase 0xE00D2000
|
|
target create $_CHIPNAME.cm4 cortex_m -dap $_CHIPNAME.dap -ap-num 2 -defer-examine
|
|
|
|
targets $_CHIPNAME.cpu0
|
|
|
|
target smp $_CHIPNAME.cpu0 $_CHIPNAME.cpu1
|
|
$_CHIPNAME.cpu0 cortex_a maskisr on
|
|
$_CHIPNAME.cpu1 cortex_a maskisr on
|
|
$_CHIPNAME.cpu0 cortex_a dacrfixup on
|
|
$_CHIPNAME.cpu1 cortex_a dacrfixup on
|
|
|
|
cti create $_CHIPNAME.cti.sys -dap $_CHIPNAME.dap -ap-num 1 -baseaddr 0xE0094000
|
|
cti create $_CHIPNAME.cti.cpu0 -dap $_CHIPNAME.dap -ap-num 1 -baseaddr 0xE00D8000
|
|
cti create $_CHIPNAME.cti.cpu1 -dap $_CHIPNAME.dap -ap-num 1 -baseaddr 0xE00D9000
|
|
cti create $_CHIPNAME.cti.cm4 -dap $_CHIPNAME.dap -ap-num 2 -baseaddr 0xE0043000
|
|
|
|
# interface does not work while srst is asserted
|
|
# this is target specific, valid for every board
|
|
# Errata "2.3.5 Incorrect reset of glitch-free kernel clock switch" requires
|
|
# srst to force VDDCORE power cycle or pull srst_core. Both cases reset the
|
|
# debug unit, behavior equivalent to "srst_pulls_trst"
|
|
reset_config srst_gates_jtag srst_pulls_trst
|
|
|
|
adapter speed 5000
|
|
adapter srst pulse_width 200
|
|
# bootrom has an internal timeout of 1 second for detecting the boot flash.
|
|
# wait at least 1 second to guarantee we are out of bootrom
|
|
adapter srst delay 1100
|
|
|
|
add_help_text axi_secure "Set secure mode for following AXI accesses"
|
|
proc axi_secure {} {
|
|
$::_CHIPNAME.dap apsel 0
|
|
$::_CHIPNAME.dap apcsw 0x10006000
|
|
}
|
|
|
|
add_help_text axi_nsecure "Set non-secure mode for following AXI accesses"
|
|
proc axi_nsecure {} {
|
|
$::_CHIPNAME.dap apsel 0
|
|
$::_CHIPNAME.dap apcsw 0x30006000
|
|
}
|
|
|
|
axi_secure
|
|
|
|
proc dbgmcu_enable_debug {} {
|
|
# set debug enable bits in DBGMCU_CR to get ap2 and cm4 visible
|
|
catch {$::_CHIPNAME.ap1 mww 0xe0081004 0x00000007}
|
|
}
|
|
|
|
proc toggle_cpu0_dbg_claim0 {} {
|
|
# toggle CPU0 DBG_CLAIM[0]
|
|
$::_CHIPNAME.ap1 mww 0xe00d0fa0 1
|
|
$::_CHIPNAME.ap1 mww 0xe00d0fa4 1
|
|
}
|
|
|
|
proc detect_cpu1 {} {
|
|
$::_CHIPNAME.ap1 mem2array cpu1_prsr 32 0xE00D2314 1
|
|
set dual_core [expr $cpu1_prsr(0) & 1]
|
|
if {! $dual_core} {$::_CHIPNAME.cpu1 configure -defer-examine}
|
|
}
|
|
|
|
# FIXME: most of handler below will be removed once reset framework get merged
|
|
$_CHIPNAME.ap1 configure -event reset-deassert-pre {adapter deassert srst deassert trst;dap init;catch {$::_CHIPNAME.dap apid 1}}
|
|
$_CHIPNAME.ap2 configure -event reset-deassert-pre {dbgmcu_enable_debug}
|
|
$_CHIPNAME.cpu0 configure -event reset-deassert-pre {$::_CHIPNAME.cpu0 arp_examine}
|
|
$_CHIPNAME.cpu1 configure -event reset-deassert-pre {$::_CHIPNAME.cpu1 arp_examine allow-defer}
|
|
$_CHIPNAME.cpu0 configure -event reset-deassert-post {toggle_cpu0_dbg_claim0}
|
|
$_CHIPNAME.cm4 configure -event reset-deassert-post {$::_CHIPNAME.cm4 arp_examine;if {[$::_CHIPNAME.ap2 curstate] == "halted"} {$::_CHIPNAME.cm4 arp_poll;$::_CHIPNAME.cm4 arp_poll;$::_CHIPNAME.cm4 arp_halt}}
|
|
$_CHIPNAME.ap1 configure -event examine-start {dap init}
|
|
$_CHIPNAME.ap2 configure -event examine-start {dbgmcu_enable_debug}
|
|
$_CHIPNAME.cpu0 configure -event examine-end {detect_cpu1}
|
|
$_CHIPNAME.ap2 configure -event examine-end {$::_CHIPNAME.cm4 arp_examine}
|