92 lines
1.9 KiB
INI
92 lines
1.9 KiB
INI
# SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
# script for stm8l family
|
|
|
|
#
|
|
# stm8 devices support SWIM transports only.
|
|
#
|
|
|
|
transport select swim
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME stm8l
|
|
}
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# By default use 1kB
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x400
|
|
}
|
|
|
|
if { [info exists FLASHSTART] } {
|
|
set _FLASHSTART $FLASHSTART
|
|
} else {
|
|
set _FLASHSTART 0x8000
|
|
}
|
|
|
|
if { [info exists FLASHEND] } {
|
|
set _FLASHEND $FLASHEND
|
|
} else {
|
|
set _FLASHEND 0xffff
|
|
}
|
|
|
|
if { [info exists EEPROMSTART] } {
|
|
set _EEPROMSTART $EEPROMSTART
|
|
} else {
|
|
set _EEPROMSTART 0x4000
|
|
}
|
|
|
|
if { [info exists EEPROMEND] } {
|
|
set _EEPROMEND $EEPROMEND
|
|
} else {
|
|
set _EEPROMEND 0x43ff
|
|
}
|
|
|
|
if { [info exists OPTIONSTART] } {
|
|
set _OPTIONSTART $OPTIONSTART
|
|
} else {
|
|
set _OPTIONSTART 0x4800
|
|
}
|
|
|
|
if { [info exists OPTIONEND] } {
|
|
set _OPTIONEND $OPTIONEND
|
|
} else {
|
|
set _OPTIONEND 0x487f
|
|
}
|
|
|
|
if { [info exists BLOCKSIZE] } {
|
|
set _BLOCKSIZE $BLOCKSIZE
|
|
} else {
|
|
set _BLOCKSIZE 0x80
|
|
}
|
|
|
|
swim newtap $_CHIPNAME cpu
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
|
|
target create $_TARGETNAME stm8 -chain-position $_CHIPNAME.cpu
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x0 -work-area-size $_WORKAREASIZE -work-area-backup 1
|
|
$_TARGETNAME configure -flashstart $_FLASHSTART -flashend $_FLASHEND -eepromstart $_EEPROMSTART -eepromend $_EEPROMEND
|
|
$_TARGETNAME configure -optionstart $_OPTIONSTART -optionend $_OPTIONEND -blocksize $_BLOCKSIZE
|
|
|
|
# Uncomment this line to enable interrupts while instruction step
|
|
#$_TARGETNAME configure -enable_step_irq
|
|
|
|
# Set stm8l type
|
|
$_TARGETNAME configure -enable_stm8l
|
|
|
|
# Set high speed
|
|
adapter speed 800
|
|
# Set low speed
|
|
#adapter speed 363
|
|
|
|
reset_config srst_only
|
|
|
|
#uncomment this line to connect under reset
|
|
#reset_config srst_nogate connect_assert_srst
|