100 lines
3.7 KiB
INI
100 lines
3.7 KiB
INI
adapter speed 1000
|
|
transport select jtag
|
|
|
|
reset_config srst_nogate
|
|
|
|
set _CHIPNAME gd32vf103
|
|
# The vendor's configuration expects an ID of 0x1e200a6d, but this one is what
|
|
# I have on my board (Sipeed Longan Nano, GD32VF103CBT6).
|
|
jtag newtap $_CHIPNAME cpu -irlen 5 -expected-id 0x1000563d
|
|
jtag newtap $_CHIPNAME bs -irlen 5 -expected-id 0x790007a3
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME riscv -chain-position $_TARGETNAME
|
|
$_TARGETNAME riscv set_enable_virt2phys off
|
|
|
|
proc default_mem_access {} {
|
|
riscv set_mem_access progbuf
|
|
}
|
|
|
|
default_mem_access
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size 0x1000 -work-area-backup 1
|
|
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME stm32f1x 0x08000000 0 0 0 $_TARGETNAME
|
|
|
|
# Address 0 is only aliased to main flash when the chip is not running its
|
|
# built-in bootloader. When it is, it's instead aliased to a read only section
|
|
# of flash at 0x1fffb000. However, we can't detect or dynamically switch this,
|
|
# so just pretend it's always aliased to main flash. We need to tell OpenOCD
|
|
# about this alias because otherwise we'll try to use software breakpoints on
|
|
# code in flash, which don't work because flash mappings are read-only.
|
|
flash bank $_CHIPNAME.flashalias virtual 0x0 0 0 0 $_TARGETNAME $_FLASHNAME
|
|
|
|
# On this chip, ndmreset (the debug module bit that triggers a software reset)
|
|
# doesn't work. So for JTAG connections without an SRST, we need to trigger a
|
|
# reset manually. This is an undocumented reset sequence that's used by the
|
|
# JTAG flashing script in the vendor-supplied GD32VF103 PlatformIO plugin:
|
|
#
|
|
# https://github.com/sipeed/platform-gd32v/commit/f9cbb44819bc05dd2010cc815c32be0486800cc2
|
|
#
|
|
$_TARGETNAME configure -event reset-assert {
|
|
set dmcontrol 0x10
|
|
set dmcontrol_dmactive [expr 1 << 0]
|
|
set dmcontrol_haltreq [expr 1 << 31]
|
|
|
|
global _RESETMODE
|
|
global _TARGETNAME
|
|
|
|
# Halt the core so that we can write to memory. We do this first so
|
|
# that it doesn't clobber our dmcontrol configuration.
|
|
halt
|
|
|
|
# Set haltreq appropriately for the type of reset we're doing. This
|
|
# replicates what the generic RISC-V reset_assert() function would
|
|
# do if we weren't overriding it. The $_RESETMODE hack sucks, but
|
|
# it's the least invasive way to determine whether we need to halt,
|
|
# and psoc6.cfg already uses the same trick. (reset_deassert(), which
|
|
# does run, also does this, but at that point it may be too late: the
|
|
# reset has already been triggered, so there's a race between it and
|
|
# the haltreq write.)
|
|
#
|
|
# If we didn't override the generic handler, we'd actually still have
|
|
# to do this: the default handler sets ndmreset, which prevents memory
|
|
# access even though it doesn't actually trigger a reset on this chip.
|
|
# So we'd need to unset it here, which involves a write to dmcontrol,
|
|
# Since haltreq is write-only and there's no way to leave it unchanged,
|
|
# we'd have to figure out its proper value anyway.
|
|
set val $dmcontrol_dmactive
|
|
if {$_RESETMODE ne "run"} {
|
|
set val [expr $val | $dmcontrol_haltreq]
|
|
}
|
|
$_TARGETNAME riscv dmi_write $dmcontrol $val
|
|
|
|
# Unlock 0xe0042008 so that the next write triggers a reset
|
|
$_TARGETNAME mww 0xe004200c 0x4b5a6978
|
|
|
|
# We need to trigger the reset using abstract memory access, since
|
|
# progbuf access tries to read a status code out of a core register
|
|
# after the write happens, which fails when the core is in reset.
|
|
riscv set_mem_access abstract
|
|
|
|
# Go!
|
|
$_TARGETNAME mww 0xe0042008 0x1
|
|
|
|
# Put the memory access mode back to what it was.
|
|
default_mem_access
|
|
}
|
|
|
|
# Capture the mode of a given reset so that we can use it later in the
|
|
# reset-assert handler.
|
|
proc init_reset { mode } {
|
|
global _RESETMODE
|
|
set _RESETMODE $mode
|
|
|
|
if {[using_jtag]} {
|
|
jtag arp_init-reset
|
|
}
|
|
}
|