######################################
# Target: DIGI ConnectCore Wi-9C
######################################

reset_config trst_and_srst

# FIXME use some standard target config, maybe create one from this
#
#	source [find target/...cfg]

if { [info exists CHIPNAME] } {
   set  _CHIPNAME $CHIPNAME
} else {
   set  _CHIPNAME ns9360
}

if { [info exists ENDIAN] } {
   set  _ENDIAN $ENDIAN
} else {
  # This config file was defaulting to big endian..
   set  _ENDIAN big
}


# What's a good fallback frequency for this board if RCLK is
# not available??
jtag_rclk 1000


if { [info exists CPUTAPID ] } {
   set _CPUTAPID $CPUTAPID
} else {
   set _CPUTAPID 0x07926031
}

set _TARGETNAME $_CHIPNAME.cpu
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID

adapter_nsrst_delay 200
jtag_ntrst_delay 0


######################
# Target configuration
######################

target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position $_TARGETNAME

$_TARGETNAME configure -event reset-init {
	mww 0x90600104 0x33313333
	mww 0xA0700000 0x00000001  # Enable the memory controller.
	mww 0xA0700024 0x00000006  # Set the refresh counter 6
	mww 0xA0700028 0x00000001  #
	mww 0xA0700030 0x00000001  # Set the precharge period
	mww 0xA0700034 0x00000004  # Active to precharge command period is 16 clock cycles
	mww 0xA070003C 0x00000001  # tAPR
	mww 0xA0700040 0x00000005  # tDAL
	mww 0xA0700044 0x00000001  # tWR
	mww 0xA0700048 0x00000006  # tRC 32 clock cycles
	mww 0xA070004C 0x00000006  # tRFC 32 clock cycles
	mww 0xA0700054 0x00000001  # tRRD
	mww 0xA0700058 0x00000001  # tMRD
	mww 0xA0700100 0x00004280  # Dynamic Config 0 (cs4)
	mww 0xA0700120 0x00004280  # Dynamic Config 1 (cs5)
	mww 0xA0700140 0x00004280  # Dynamic Config 2 (cs6)
	mww 0xA0700160 0x00004280  # Dynamic Config 3 (cs7)
	#
	mww 0xA0700104 0x00000203  # CAS latency is 2 at 100 MHz
	mww 0xA0700124 0x00000203  # CAS latency is 2 at 100 MHz
	mww 0xA0700144 0x00000203  # CAS latency is 2 at 100 MHz
	mww 0xA0700164 0x00000203  # CAS latency is 2 at 100 MHz
	#
	mww 0xA0700020 0x00000103  # issue SDRAM PALL command
	#
	mww 0xA0700024 0x00000001  # Set the refresh counter to be as small as possible
	#
	# Add some dummy writes to give the SDRAM time to settle, it needs two
	# AHB clock cycles, here we poke in the debugger flag, this lets
	# the software know that we are in the debugger
	mww 0xA0900000 0x00000002
	mww 0xA0900000 0x00000002
	mww 0xA0900000 0x00000002
	mww 0xA0900000 0x00000002
	mww 0xA0900000 0x00000002
	#
	mdw 0xA0900000
	mdw 0xA0900000
	mdw 0xA0900000
	mdw 0xA0900000
	mdw 0xA0900000
	#
	mww 0xA0700024 0x00000030 # Set the refresh counter to 30
	mww 0xA0700020 0x00000083 # Issue SDRAM MODE command
	#
	# Next we perform a read of RAM.
	# mw = move word.
	mdw 0x00022000
	# mw 0x00022000:P, r3  # 22000 for cas2 latency, 32000 for cas 3
	#
	mww 0xA0700020 0x00000003   # issue SDRAM NORMAL command
	mww 0xA0700100 0x00084280   # Enable buffer access
	mww 0xA0700120 0x00084280   # Enable buffer access
	mww 0xA0700140 0x00084280   # Enable buffer access
	mww 0xA0700160 0x00084280   # Enable buffer access

	#Set byte lane state (static mem 1)"
	mww 0xA0700220 0x00000082
	#Flash Start
	mww 0xA09001F8 0x50000000
	#Flash Mask Reg
	mww 0xA09001FC 0xFF000001
	mww 0xA0700028 0x00000001

	#  RAMAddr = 0x00020000
	#  RAMSize = 0x00004000

	# Set the processor mode
	reg cpsr 0xd3
}

$_TARGETNAME configure -work-area-phys 0x00000000 -work-area-size 0x1000 -work-area-backup 1

#####################
# Flash configuration
#####################

#M29DW323DB - not working
#flash bank cfi <base> <size> <chip width> <bus width> <target#>
set _FLASHNAME $_CHIPNAME.flash
flash bank $_FLASHNAME cfi 0x50000000 0x0400000 2 2 0