Highlight that the "post-reset" event kicks in before the
scan chain is validated, which limits what can be done
in a post-reset handler.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2745 b42882b7-edfa-0310-969c-e2dbd0fdcd60
done on exit from the config stage, how JTAG clocking issues can
trigger errors there, and how to avoid such problems.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2737 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Erase logic:
- command invocation
+ treat "nand erase N" (no offset/length) as "erase whole chip N"
+ catch a few more bogus parameter cases, like length == 0 (sigh)
- nand_erase() should be static
- on error
+ say which block failed, and if it was a bad block
+ don't give up after the first error; try to erase the rest
- on success, say which nand device was erased (name isn't unique)
Device list ("nand list"):
- say how many blocks there are
- split summary into two lines
- give example in the docs
Doc tweaks:
- Use @option{...} for DaVinci's supported hardware ECC options
For the record, I've observed that _sometimes_ erasing bad blocks causes
failure reports, and that manufacturer bad block markers aren't always
erasable (even when erasing their blocks doesn't trigger an error report).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2724 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- update comments to say so.
- update docs to clarify that the "arm9tdmi" command prefix
is a misnomer.
- bugfix some messages that wrongly assume only ARM9TDMI
based processors use this code.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2719 b42882b7-edfa-0310-969c-e2dbd0fdcd60
JTAG clocking by gating the core clock, and workarounds.
Most details are with the "halt" command, which is one
of the first places this issue will be noticed.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2718 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Fix docs on ARM11 MCR and MRC coprocessor commands:
correct read-vs-write; and describe the params.
(ARM920 and ARM926 have cp15-specific commands; this
approach is more generic. MCR2, MRC2, MCRR, MCRR2,
MRRC, and MRRC2 instructions could also get exposed.)
git-svn-id: svn://svn.berlios.de/openocd/trunk@2679 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Provide an "armv7a disassemble" command. Current omissions include
VFP (except as coprocessor instructions), Neon, and various Thumb2
opcodes that are not available in ARMv7-M processors.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2676 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Itemize the list of private customization examples
for openocd.cfg
- Add "override defaults" as a customization, specifically
for the work area (back it up or relocate it)
- Highlight some work area location issues
git-svn-id: svn://svn.berlios.de/openocd/trunk@2651 b42882b7-edfa-0310-969c-e2dbd0fdcd60
For ARMv4/ARMv5:
- better command parameter error checking
- don't require an instruction count; default to one
- recognize thumb function addresses
- make function static
- shorten some too-long lines
For Cortex-M3:
- don't require an instruction count; default to one
With the relevant doc updates.
---
Nyet done: invoke the thumb2 disassembler on v4/v5,
to better handle branch instructions.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2624 b42882b7-edfa-0310-969c-e2dbd0fdcd60
the values that are written in the mini-IC (plus documentation updates that
describe why this is needed).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2613 b42882b7-edfa-0310-969c-e2dbd0fdcd60
issue with this is that the core debug support uses this
mechanism, then trashes its state over reset. Users can
Work around that (for now) by re-assigning the desired
config after reset.
Also fixes "target halted due to target-not-halted" goof.
When we can't describe the reason using OpenOCD's limited
vocabulary, say "reason undefined" instead of saying it's
not halted.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2588 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Add flash programming support for NXP LPC1700 cortex_m3 based family
git-svn-id: svn://svn.berlios.de/openocd/trunk@2579 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Initial support for disassembling Thumb2 code. This works only for
Cortex-M3 cores so far. Eventually other cores will also need Thumb2
support ... but they don't yet support any kind of disassembly.
- Update the 16-bit Thumb decoder:
* Understand CPS, REV*, SETEND, {U,S}XT{B,H} opcodes added
by ARMv6. (It already seems to treat CPY as MOV.)
* Understand CB, CBNZ, WFI, IT, and other opcodes added by
in Thumb2.
- A new Thumb2 instruction decode routine is provided.
* This has a different signature: pass the target, not the
instruction, so it can fetch a second halfword when needed.
The instruction size is likewise returned to the caller.
* 32-bit instructions are recognized but not yet decoded.
- Start using the current "UAL" syntax in some cases. "SWI" is
renamed as "SVC"; "LDMIA" as "LDM"; "STMIA" as "STM".
- Define a new "cortex_m3 disassemble addr count" command to give
access to this disassembly.
Sanity checked against "objdump -d" output; a bunch of the new
instructions checked out fine.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2530 b42882b7-edfa-0310-969c-e2dbd0fdcd60
on ARM9 cores, and update the DaVinci config files so they
no longer explicitly specify it.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2484 b42882b7-edfa-0310-969c-e2dbd0fdcd60
reading the output, and both were reported in openocd.log
after making the PDF.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2449 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Add some text to introduce the project to new users.
Move packaging, configuration, and compilation of OpenOCD out of
the User's Guide and into README, where it can be used by users
before configuring and compiling the documentation.
Improve notes about required Subversion repository build steps.
Add reference to the standard GNU INSTALL file.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2436 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This patch adds support for the Luminary Micro LM3S9B90 target and
LM3S9B92 Evaluation Kit. These kits include a new ft2232 adapter, the
Luminary In-Circuit Debug Interface (ICDI) Board, so this is added as a
new ft2232 layout called "luminary_icdi".
git-svn-id: svn://svn.berlios.de/openocd/trunk@2429 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Add "jtag names" command, mirroring "target names" but returning
TAP names instead of target names. This starts letting TAPs be
manipulated in scripts ... much like what works now for targets.
It's a bit limited just yet, since "jtag cget $TAPNAME" doesn't
expose all TAP attributes. "$TARGETNAME cget" is more functional.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2428 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Warn when people (or scripts) use numeric identifiers for TAPs,
instead of dotted.name values. We want this usage to go away,
so that for example adding more TAPs doesn't cause config scripts
to break because some sequence number changed.
It's been deprecated since late 2008, but putting a warning on
this should help us remove it (say, in June 2010) by helping to
phase out old (ab)usage in config scripts.
Other than in various config files, the only code expecting such
a number was the almost unused str9xpec driver. This code was
changed to use the TAP it was passed, instead of making its own
dubious lookup and ignoring that TAP.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2415 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Minor fixup to the User's Guide, primarily related to the
handful of commands defined in "startup.tcl"; "help" was
not previously documented.
Also, be more consistent about "Config Command" definitions
(and to be explicit about that doc convention).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2414 b42882b7-edfa-0310-969c-e2dbd0fdcd60
and some formatting issues with sam7 and stm32 keyword params.
Tweak at91sam3 docs. Remove ninth nibble from flash bank addresses,
clarify "at91sam3 show" variants and that the flash bank layout is
not needed as a parameter (unlike with sam7); formatting fixes.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2400 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Move the short chapter about JIM-Tcl earlier, so that we
can reasonably assume it's been introduced before we start
presenting things that presume such an introduction.
Plus a few minor typo-level fixes.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2355 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This should be my last significant update of the User's Guide for
this release. Mostly it's a rework of the config file chapter's
presentation of board and target config files.
- Give the new path for scripts!
- Move board-config material out of the target-config section
- Add more board-config info, notably for reset-init events
- Link out of the board-config section to NAND, NOR, and Reset chapters
- Emphasize target input vs. output naming conventions
- Other textual improvements
Plus some other updates, like adding my copyright (now that I've
basically rewritten much of this).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2354 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This is minimal patch to support FA526 ARMv4 compatible core.
Since it is very similar to ARM920T I tried to reuse as much
code as possible.
CPU and board configs will follow soon.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2292 b42882b7-edfa-0310-969c-e2dbd0fdcd60
The PLD stuff hasn't been documented yet. It's just Virtex2 for now,
but it looks like adding others would be easy.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2273 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Various bits of cleanup, mostly to match the style hints
I just got around to writing up.
- Various @cindex improvements
- Cross reference the command line options in a few spots,
notably for @command{debug_level}
- Clean the config file guidelines a bit:
* They're for all users, not just integrators
* Reference the interface config chapter
* Don't emphasize command line usage here
* Tweak board and target config introductory text
Plus two minor bits of cleanup: remove most date references,
and refer to the reader as "you" not "the user".
git-svn-id: svn://svn.berlios.de/openocd/trunk@2271 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Distributing FTDI's "ftd2xx" library with OpenOCD violates the
OpenOCD license (GNU GPLv2 with no exceptions).
Make that clear where that build option is presented, and don't
describe the FTDI libraries as an option for any packager. (It's
fine for personal use, of course.)
Plus some related clarifications: libftdi version 0.16 for the
new FT2232H chips (for RTCK and high speed USB); the Amontec
drivers are just ftd2xx variants.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2248 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Doc update: say "jtag newtap ... -disable" records the
state after exiting the RESET state, matching the only
implementation we're working with so far (TI ICEpick-C).
Matching code updates. Now we can be sure that the
"enabled" flag value is correct after JTAG resets.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2246 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Minor updates to the text about reset configuration:
- Mention a new point that it interacts with JTAG routers;
- Talk about a "user" config file not a "system" one;
- Remove text from the "reset_config" description; instead,
cross-reference the more extensive text earlier.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2243 b42882b7-edfa-0310-969c-e2dbd0fdcd60
OpenOCD doesn't actually *need* to be keeping all TCP ports
active ... creating security issues in some network configs.
Instead, let config file specify e.g. "tcl_port 0" (or gdb_port,
telnet_port) to disable that particular remote access method.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2240 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Move the discussion of the "scan_chain" command up to go with
the presentation of that topic in the TAP declaration chapter.
This makes the presentation of the TAP and target lists be
parallel, which will be something of an aid to understanding
that they are different (and how).
git-svn-id: svn://svn.berlios.de/openocd/trunk@2223 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Rework the "Simple Configuration Files" chapter so it's more
of a quick-start "how to set up your project" tutorial:
- Say how to hook up the JTAG adapter. This will help new
users, and in any case is worth spelling out somewhere.
- Streamline the previous rather haphazard presentation,
filling in some missing holes along the way:
* Suggest "project directory" structure
* Introduce new term, "user config" file (openocd.cfg)
* Talk about more options for openocd.cfg contents
* ... and about creating new config files
* Add new topic, project-specific utilities (+examples)
- Remove too-short, yet duplicative, chapter 19
Nudge packagers a bit more strongly to send patches (including
config files) upstream.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2204 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Update "arm9tdmi vector_catch" command description to highlight both
use cases (display configuration, or first change that config) and
to explain a bit more about what this is: an alternative to using
hardware breakpoint resources.
Note that I tried this on an arm920t, but it didn't work. Set bits,
then examined them and they weren't set. And it didn't seem to act
as if vector triggering was noticed, either.
Also some minor unrelated tweaks: @ignore some unused or don't-use
event names; fix a few typos; tweak chip-specific reset descriptions.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2203 b42882b7-edfa-0310-969c-e2dbd0fdcd60
other server configuration. Explain what it's about;
reference the related "$target_name curstate" method.
Update "poll" output to report whether background polling
is enabled or not.
Also fix a small typo; PC's have "complementary" tools.
Some have also "complimentary" ones; but not all.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2178 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Don't let disabled TAPs be set as the current target
- Improve "targets" output:
* Remove undesirable "chain position" number; we discourage using them
* TAP and Target column updates:
+ make them long enough for current usage
+ improve labels, removing guesswork
+ "TapName" label patches scan_chain output
* Highlight the "current" target
* Display "tap disabled" as a new pseudo-state
* Update docs accordingly
git-svn-id: svn://svn.berlios.de/openocd/trunk@2107 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Clarify docs for the evb_lm3s811 layout: works in
two modes, not just one.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2099 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Rework chapter 12 (CPU configuration) to use @deffn, match
the code more closely, and present things more clearly.
Includes the *current* list of targets.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2097 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Various minor tweaks for the User's guide.
- Fix various minor (but repeated) typographic goofs;
- Talk about TAP "declaration" not "creation" (they exist
even if OpenOCD never learns about their board);
- Encourage board.cfg for reset config, not target.cfg
- Fill in some missing information (e.g. x16_as_x8)
- Add a cross reference to the FAQ on TAP ordering;
- Unclutter the concept index a bit (re core-specific commands)
- Provide a bit more info about TAP states
git-svn-id: svn://svn.berlios.de/openocd/trunk@2096 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Update the "General Commands" (a.k.a. "random stuff") chapter,
and associated chunks of other text:
- Switch to @deffn and review everything that's documented
- Improve descriptions of reset events, with reference to
the setup.tcl code which issues them.
- Move one zy1000-specific command to that driver's doc.
- There is no "script" command; remove its doc.
NOTE: Some things missing from this bit of work are:
1- Reviewing the code to catch various *missing* functions,
mostly from "target.c"
2- Alphabetizing and organizing. This chapter is a real
grab-bag with no evident focus or structural principle.
3- Hole-filling and bugfixing with respect to messaging/logging.
Example, what principle could possibly justify the tcl command
output going into the server output/log instead of just the
telnet session?
4- Not just for this chapter ... but there should be a section
with descriptions of all the supported image file formats,
so every image command can just reference that section.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2039 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Convert the Interface/Dongle Config chapter's section
on drivers to use the @deffn syntax, and integrate the
presentation of the driver-specific commands with the
relevant driver. Alphabetize.
Cross-checked against the code ... several adapters were
not listed, and a few commands weren't.
(Maintainers for the versaloon and zy1000 drivers would be
good candidates to add the commands missing from those
sections...)
git-svn-id: svn://svn.berlios.de/openocd/trunk@2035 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Convert the str9xpec driver info to use @deffn; alphabetize;
add the missing part_id command.
Convert the mflash support to use @deffn; alphabetize.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2034 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Update docs for most of the remaining commands in jtag.c:
- switch to @deffn
- these are just the "low level" JTAG commands
- resolve much goofage!
* remove docs for non-existent commands
* add missing docs for some existing commands
* fix incorrect docs for some commands
- just index TAP states overall, not individually
- current name is "RUN/IDLE" not "IDLE"
Cross checked against the source.
This also creates an "Interface Drivers" section, analagous to how
(NOR) Flash and NAND drivers are presented; that's not yet sorted.
git-svn-id: svn://svn.berlios.de/openocd/trunk@2014 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Rework the TAP creation documentation.
- Try to use "TAP" not "tap" everywhere; it's an acronym.
- Update the associated "target config files" section:
* reference the "TAP Creation" chapter for details
* simplify: reference interesting multi-tap config files
* let's not forget CPU configuration (*before* workspace setup)
* streamline it a bit
* move that workspace-vs-mmu issue to a better location
- Clean up TAP creation doc mess
* switch to @deffn
* (re)organize the remaining stuff
* reference the "Config File Guidelines" chapter
- Tweak the "Target Configuration" chapter
* rename as "CPU configuration"; unconfuse vs. target/*.cfg
* bring out that it's not just there for GDB
* move TAP events to the TAP chapter, where they belong (bugfix)
git-svn-id: svn://svn.berlios.de/openocd/trunk@2013 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- change SWJDP_IR/DR_APACC to DAP_IR/DR_APACC to conform with ARM_ADI docs.
- add swjdp->memaccess_tck field and code for extra tck clocks before accessing memory bus
- Set default memaccess value to 8 for Cortex-M3.
- Add dap memaccess command.
- document all armv7 dap cmds.
- Original patch submitted by Magnus Lundin [lundin@mlu.mine.nu].
git-svn-id: svn://svn.berlios.de/openocd/trunk@2005 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Remove two sections about deprecated/removed commands, documenting
them briefly in the chapter on deprecated/removed commands. The
"working_area" command just duplicated text; "jtag_device" wasn't
listed in that chapter before.
Also start de-emphasizing those commands. Don't index them, and
include a disclaimer that their documentation may start to vanish
about a year after the code does (e.g. in January 2010).
git-svn-id: svn://svn.berlios.de/openocd/trunk@1986 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Uplevel the arch commands to be a chapter; they really
don't fit in the "general commands" category.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1977 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Fix minor goofage in previous doc updates:
* The ETM dummy driver name is "dummy" not "etm_dummy";
re-alphabetize.
* DCC trace message mode "charmsg" is a format type
(and what Linux needs)
git-svn-id: svn://svn.berlios.de/openocd/trunk@1976 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Various updates, mostly small/formatting changes:
* Small content tweaks:
- Re-title: "OpenOCD User's Guide".
- For users, URLS for latest doc and SparkFun forum
- Mention GIT-SVN
* Fix some front-matter goofage, matching texinfo docs:
- "paragraphintent" location matters
- put release version/date description with the copyright
* Fix some other stuff matching texinfo docs:
- no tabs
- tweak some refs and anchors
* whitespace-at-end-o-line fixes
git-svn-id: svn://svn.berlios.de/openocd/trunk@1975 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Provide basic documentation on the ARM ETM and ETB trace commands.
Fix minor goofs in registration of the ETM commands; and whitespace
issues in the proof-of-concept oocd_trace code. (Plus include a
ref to Dominic's email saying that it's just proof-of-concept code.)
Note that I'm still not sure whether the ETM support works. But
documenting how it's expected to work should help sort out which
behaviors are bugs, which will help get bugs patched.
ZW: whitespace changes were split out of this patch but will follow.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1945 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Make it so the magic "reset_config" keywords can be provided in any
order. This eliminates needless error paths, and makes it easier
to define things at the right level (adapter, board, target).
It also includes two other behavioral changes:
(1) When "handle_reset_config" sees a parameter error, it
exits without changing anything. This is best viewed
as a bugfix. (Old behavior: restore defaults, even if
they weren't previously active.)
(2) Only the behaviors that were explicitly specified get
changed. (Old behavior: everything else gets reset to
the "default".) So for example you can now specify SRST
drive requirements without saying anything about the
three unrelated topics you previously had to specify.
That second one might cause confusion for any configs that end
up calling "reset_config" twice, so it will deserve to be called
out in the release notes. (There were no such configurations in
the current OpenOCD source tree.)
Update docs accordingly. Note that at least some versions of
the texi-to-html tools can't handle "@xref{with spaces}", but
those work properly in PDF and in the info files.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1944 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Provide basic documentation for some of the other flash drivers.
avr ... looks incomplete, may work with one AVR8 microcontroller
ecosflash ... can't find docs
lpc288x ... an NXP part, driver seems lpc2888-specific
ocl ... some arm7/arm9 thing, can't find docs
pic32mx ... looks incomplete, for PIC32MX (MIPS 4K) devices
tms470 ... for TI TMS470 parts
Still seems to be mostly arm7tdmi... several of these have no
users in the current tree.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1941 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Start converting the architecture-specific commands to @deffn format,
reviewing against the code.
* armv4_5 disassemble ... now documented; although Jazelle code
is not handled
* It's "armv4_5 core_state" not "core_mode"; although Jazelle state
is not handled
* arm7/9 "debug" commands ... now with other arm7_9 commands, no
longer in a separate section
* arm926ejs cp15 ... previous description was broken, it matched
the code for arm920t instead
* Have separate subsections for ARMv4/ARMv5, ARMv6, and ARMv7; the
latter are new
* Move core-specific descriptions into sub-subsections under those
architectures; XScale and ARM11 descriptions are new
The new XScale and ARM11 command descriptions surely need elaboration
and review. ARM CP15 operation descriptions in general seem to be
confused and incomplete.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1939 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Continue updating the NOR flash coverage to use @deffn syntax, so the
commands have more consistent presentation and formatting. This
reorganizes information and updates its presentation, except where
the information didn't really match the code.
This patch updates the main commands, and finishes making the section
structure parallel the NAND presentation. Of note:
- The "flash fill[whb] addr value length" commands are now documented.
- The "flash bank" command is now presented much earlier
- Explicit mention is made that NOR flash should be read using just
standard memory access commands, like "mdw" and "dump_image".
git-svn-id: svn://svn.berlios.de/openocd/trunk@1938 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Start updating the NOR flash coverage to use @deffn syntax, so the
commands have more consistent presentation and formatting. This
reorganizes information and updates its presentation, except where
the information didn't really match the code.
This patch updates most of the driver specific support, creating one
new (and alphabetized!) section just for driver-specific data, where
previously that data was split over up to three sections. Of note:
- The at91sam7 docs were a bit out of date with respect to the code.
- The "str9xpec" stuff still deserves some work. For now, it sits
in its own subsection; pretty messy.
- Likewise the "mflash" stuff. That's a parallel infrastructure,
and is now in a section of its own.
- The "mass_erase" commands for the Cortex M3 chips got turned into
footnotes. IMO, they should vanish sometime; they're superfluous.
- There are still a bunch of undocumented NOR drivers. Examples:
avr(8), tms470, pic32mx, more.
Plus there are a handful of minor tweaks to the NAND docs (to help make
the NOR and NAND presentations be parallel); the "Command Index" has
been renamed as the "Command and Driver Index"; reference TI instead
of Luminary Micro in several places.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1937 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Fix a bunch of PDF generation bugs in the texi:
* The "overfull" warnings are basically complaints about lines
that are too long, so they ran off the right margin of the
PDF documentation and turn into a "black blot".
* The "underfull" warnings are basically complaints about lines
that look ugly when they get filled, because the tokens are
so long that the line-break algorithm can't do anything good.
In a few cases the simplest fix seemed to be to use more appropriate
texi commands.
In other cases the fix was a content bugfix: "ocd_" not "openocd_";
and many of those "target variants" actually aren't recognized.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1936 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Update the "Reset Configuration" information in the User's guide:
- Convert to @deffn syntax
- Move tutorial text from command descriptions into new sections
- Describe several different types of JTAG-visible reset
- Expand descriptions of configuration tweaks for SRST and TRST
- Link to the "reset" command, and vice versa
- Bugfix the "reset_config" description (it didn't match the code)
Plus, be more proscriptive: do it in board config files, except for
the oddball cases where that won't work. (Current target.cfg files
seem to have much goofage there; several seem board-specific.)
git-svn-id: svn://svn.berlios.de/openocd/trunk@1913 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Doc (mostly) update for jtag_khz:
- switch to @deffn syntax
- add entry for "jtag_rclk"
- move deprecated "jtag_speed" into collection of deprecated calls
And for ft2232, don't be the only adapter to *log* an error if RTCK
is requested; it's already reported properly, like any other nonfatal
command parameter. "jtag_rclk" just works as expected, without any
scarey messages.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1910 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Make startup for the various server ports be quiet, unless
debugging is active: don't emit needless scarey messages.
Update the relevant documentation and its references:
- For these port commands ... cover the default values;
convert to @deffn syntax; include their use outside of
the configuration stage; and alphabetize.
Similar updates to the rest of that small chapter:
- Highlight that there even *IS* a configuration stage, after
which some command functionality is no longer available.
- For GDB commands ... convert to @deffn syntax; alphabetize;
include a missing command (!); add missing helptext (!) for
one non-missing command; update relevant cross-references
and index entries.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1909 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Update two oddball NAND commands to work with {offset, length}
instead of block numbers, matching the other commands as well
as usage in U-Boot and the Linux-MTD utilities.
Document them accordingly. Update the single in-tree use of
those commands (sheevaplug).
ALSO:
(a) Document the current 2 GByte/chip ceiling for NAND chipsize.
(32 bit offset/length values can't represent 4 GBytes.) Maybe
after the upcoming release, the code can switch to 64-bits.
(b) The "nand check_bad_blocks" should report "bad" blocks. They
are not "invalid" blocks; they're "bad" ones.
(c) Tweak the "nand info" command to handle the "no arguments"
case sanely (show everything, instead of showing garbage) and
not listing the blocksize in hex kbytes (duh).
git-svn-id: svn://svn.berlios.de/openocd/trunk@1904 b42882b7-edfa-0310-969c-e2dbd0fdcd60
NAND support for DaVinci-family drivers, with HW ECC support.
Declare the NAND chip on the DM355 EVM board.
Currently tested on DM355 for Linux interop using the standard
large page (2KB) chip in the EVM socket; "hwecc1" and "hwecc4"
work fine. (Using hwecc4 relies on patches that haven't quite
made it through the Linux-MTD bottlenecks yet.)
Not yet tested: 1-bit on small-page (although it's hard to see
how that could fail); 4-bit on small page (picky layout issues);
the "hwecc_infix" mode (primarily for older boot ROMs; testing
there is blocked on having new bootloader code).
git-svn-id: svn://svn.berlios.de/openocd/trunk@1903 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Fix minor issues with xrefs not liking parentheses around them.
- Change 'Building' section to 'Building OpenOCD'. It reads better.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1902 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Remove style guide from user guide; moved to doxygen manual.
- Replace with improved introduction for developers and packagers.
- Move introductory paragraph about the project under the About page.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1895 b42882b7-edfa-0310-969c-e2dbd0fdcd60
Add a "NAND Commands" section to to the TEXI docs, covering the basic
commands except for those previously discussed as being due for removal
("nand copy") or switching to use byte offsets not block numbers.
This uses the "@deffn..." syntax for defining commands, as somewhat
suggested by the TEXI documentation, and adds a new "Command Index".
We might prefer to merge those indexes for the near term, but I think
the "@deffn" approch is probably worth switching to.
Updates a few other bits to clarify that "flash" doesn't just mean NOR.
And to fix one niggling falsity: the "reset-init" event *is* used, and
in fact it's quite important.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1879 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- Explicitly mention autoconf >= 2.59 as requirement (as per
configure.in). Also automake >= 1.9 (though I'm not sure which
if that's really the minimum requirement).
- Document various missing configure options.
- Fix various typos and inconsistencies.
git-svn-id: svn://svn.berlios.de/openocd/trunk@1426 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- updated missing jtag dongle url's in texi
- reformat and remove whitespace from last commit
git-svn-id: svn://svn.berlios.de/openocd/trunk@1227 b42882b7-edfa-0310-969c-e2dbd0fdcd60
the reset mode argument to the target command is deprecated(ignored w/error message).
git-svn-id: svn://svn.berlios.de/openocd/trunk@832 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This patch just uses the command.c interface to create tcl commands for the root level commands and avoids a bit of the "TCL" bleed into the rest of the openocd code.
Multilevel commands also supported.
git-svn-id: svn://svn.berlios.de/openocd/trunk@818 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- remove info on flash auto_erase, added to removed commands section
git-svn-id: svn://svn.berlios.de/openocd/trunk@596 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- native win32 now handles WSAECONNRESET - no longer exits openocd
- qCRC packet now works correctly under cygwin (gdb compare-sections command)
- removed __USE_GNU define from gdbserver.c
- gdb qSupported packet is now handled, with this we are able to tell gdb packet size, memory map of target
- added new target script gdb_program_config - called before gdb flash programming
- new gdb server command gdb_memory_map (enable|disable> - default is disable
- new gdb server command gdb_flash_program (enable|disable> - default is disable
- gdb flash programming supported - vFlash packets
- image_elf_read_section now does not clear any remaining data, this was causing the gdb checksum to fail with certain files
- reformat of usbprog.c
- memory leak in command_print fixed
- updated texi doc to include new commands
- added gdb programming section to docs
git-svn-id: svn://svn.berlios.de/openocd/trunk@246 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added LPC2148 script
- corrected size of the working_area of the LPC2294 script
git-svn-id: svn://svn.berlios.de/openocd/trunk@245 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- minor code reformat and cleanup
- updated docs to include new commands
git-svn-id: svn://svn.berlios.de/openocd/trunk@243 b42882b7-edfa-0310-969c-e2dbd0fdcd60
flash verify_image and flash erase_address.
- added patch for new parport_write_on_exit command.
Even this patch will fix some memory leaks.
(thanks too oyvind and Spen for these patches)
git-svn-id: svn://svn.berlios.de/openocd/trunk@240 b42882b7-edfa-0310-969c-e2dbd0fdcd60
dbrownell
oharboe
ntfreak
zwelch
duane
kc8apf
mifi