The driver hla defines the command 'hla_serial' to specify the
serial string of the adapter.
The driver st-link defines the command 'st-link serial' to specify
the serial string of the adapter.
Remove and deprecate the driver commands and use 'adapter serial'.
Change-Id: I9505c398a77125b1ebf4ba71da7baf4d663b75be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/6657
Tested-by: jenkins
Add the 0x3754 PID used by some STLINK-V3 devices when MSD has been
disabled. This PID has been observed on a Nucleo-G431RB board.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Change-Id: Idb85874fa5a9dff5940bae7e95426a956693b976
Reviewed-on: https://review.openocd.org/c/openocd/+/6555
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add SWIM and STM8 to documentation and update TODO file.
Introduce transport "swim" and command "swim newtap".
Switch in swim.c from HLA API to the new SWIM API.
Implement in stlink driver the SWIM APIs as wrappers of existing
HLA functions.
Remove any SWIM related reference from HLA files.
Update stm8 config files and stlink-dap interface config file.
Change-Id: I2bb9f58d52900f6eb4df05f979f7ef11fd439c24
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5530
Tested-by: jenkins
Some script have been added or modified after the patches for
reworking the adapter commands were pushed in gerrit.
Such scripts use the old command syntax and trigger a "deprecated"
warning at runtime.
Fix them with the same sed commands used for the other scripts:
sed -i 's/^interface /adapter driver /' $(find tcl/ -type f)
sed -i 's/adapter_khz/adapter speed/g' $(find tcl/ -type f)
sed -i 's/adapter_nsrst_delay/adapter srst delay/g' $(find tcl/ -type f)
sed -i 's/adapter_nsrst_assert_width/adapter srst pulse_width/g' $(find tcl/ -type f)
Change-Id: I0824d6c506a9af3eb9129b74c02a92b4eb1b100d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5424
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
STLINK-V3 and the new firmware V2J24 for ST-LINK/V2 provide API
to directly access the DAP registers.
This mode permits to use the native target in cortex_m.c, with no
need to override it with the target in hla_target.c.
Other advantages wrt HLA are: support for Cortex-A cores, support
for SoC multi-core and/or multi AP, support for OpenOCD commands
"dap" thus including control of CSW.
This obsoletes the existing HLA driver for ST-Link, that should
anyway be kept for those cases where it's not possible to update
the ST-Link firmware.
This commit introduces the minimal implementation for direct DAP
access. The implementation is much slower than the HLA because
every memory transfer requires several USB packets. Further
commits will close the performance gap.
The whole ST-Link driver is compiled under BUILD_HLADAPTER, to
remove the need to split the driver between the two modes. This
has to be reworked, but it's quite invasive!
A new interface file stlink-dap.cfg is added and should be used
in place of stlink.cfg to enable the DAP mode.
Documentation is updated and reports limitation on the maximum AP
number that can be accessed by ST-Link for some firmware already
tested.
Change-Id: I932ffe16bc81d00b1fe489e2944fda13470cce9b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4904
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Antonio Borneo
Andreas Sandberg