Firstly, create the TPIU nrf52.tpiu if using the nrf52 target. This is
standard, using AP 0 and TPIU base address 0xE0040000.
Secondly, add a pre_enable handler for this TPIU which configures the
TRACEMUX field of the TRACECONFIG register. This register is reset
every time the MCU resets, so the pre_enable handler creates a
reset-end handler to ensure the register remains set.
Change-Id: I408b20fc03dc2060c21bad0c21ed713eee55a113
Signed-off-by: Frank Plowman <post@frankplowman.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7901
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
While we can read and write from memory from the view of various
processors, all K3 debug systems have a AXI Access port that allows
us to directly access memory from debug interface. This port is
especially useful in the following scenarios:
1. Debug cache related behavior on processors as this provides a
direct bypass path.
2. Processor has crashed or inaccessible for some reason (low power
state etc.)
3. Scenarios prior to the processor getting active.
4. Debug MMU or address translation issues (example: TI's Region
Address Table {RAT} translation table used to physically map
SoC address space into R5/M4F processor address space)
The AXI-AP port is the same for all processors in TI's K3 family.
To prevent a circular-loop scenario for axi-ap accessing debug memory
with dmem (direct memory access debug), enable this only when dmem is
disabled.
Change-Id: Ie4ca9222f034ffc2fa669fb5124a5f8e37b65e3b
Reported-by: Dubravko Srsan <dubravko.srsan@dolotron.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7899
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The Texas Instruments' K3 devices are a mix of AMP and SMP systems.
The operating systems used on these processors can vary dramatically
as well. Introduce a RTOS array variable, which is keyed off the cpu
to identify which RTOS is used on that CPU. This can be "auto" or
"hwthread" in case of SMP debug etc.
For example:
AM625 with an general purpose M4F running Zephyr and 4 A53s running SMP
Linux could be invoked by:
openocd -c 'set V8_SMP_DEBUG 1' -c 'set RTOS(am625.cpu.gp_mcu) Zephyr' \
-c "set RTOS(am625.cpu.a53.0) hwthread" -f board/ti_am625evm.cfg
Change-Id: Ib5e59fa2583b3115e5799658afcdd0ee91935e82
Reported-by: Dubravko Srsan <dubravko.srsan@dolotron.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7898
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Describe the SMP Armv8 cores in SMP configuration with coreid
explicitly called out. This allows for gdb session to call the smp
behavior clearly.
Change-Id: Ie43be22db64737bbb66181f09d3c83567044f3ac
Signed-off-by: Dubravko Srsan <dubravko.srsan@dolotron.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7897
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
When _v8_smp_targets is used with V8_SMP_DEBUG=1, describe the targets
as SMP targets. However, the variable expansion is not in the context of
a proc, and a typo in referring to global $_v8_smp_targets causes this
to fail. Just refer to $_v8_smp_targets directly.
Change-Id: Iffe5fd2703bed6a9c840284285e70b8a8ce84e17
Signed-off-by: Dubravko Srsan <dubravko.srsan@dolotron.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7896
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Currently, instruction cache is being invalidated in
arc_{un,}set_breakpoint() regardless of whether the breakpoint's type is
HW or SW. For SW breakpoints, this has no net effect as the caches are
flushed as a by-product of overwriting instructions in main memory and
is thus merely unnecessary; but for HW breakpoints this invalidation is
not preceded by a flush and might lead to loss of data. This patch
removes the invalidate() call altogether to correct this undesired
behavior for HW breakpoints.
With this patch applied, all supported HW breakpoint tests from the gdb
testsuite are now passing with the arc-openocd backend.
Change-Id: I3d252b97f01f1a1e2bf0eb8fb257bdab0c544bc2
Signed-off-by: Artemiy Volkov <artemiy@synopsys.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7767
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The comment above armv8_dpm_read_current_registers() doesn't match
the implementation, as the function reads all the registers from
ARMV8_PC and above.
The registers currently read are not relevant to answer to the
usual GDB initial request through the 'g' packet. Plus the lack of
differentiation per core state (AArch32 vs AArch64) causes the
read of not existing registers in AArch32 triggering errors, as
tentatively fixed by https://review.openocd.org/5517/
Fix the code to read the registers initially required by GDB.
Modify the comment to report the register list in AArch32 and in
AArch64.
Keep the extra checks inside the read loop, even if they are
mostly irrelevant; this could prevent errors if someone needs to
extend the number of registers to read.
The current implementation of the register's description in
OpenOCD does not allow to discriminate among AArch32 and AArch64
registers. Add a TODO comment to highlight it.
Change-Id: Icd47d93c19a9e1694a7b51bbc5ca7e21a578df41
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7887
Tested-by: jenkins
Move `examine_attempted` flag to target struct to make it target specific.
`Info` messages for retry and `Error` messages for failure added.
Change-Id: Id2fbe7dc68d746c936c8412289d0d149fbd80d71
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
The secure microcontroller Infineon SLx2 uses a custom Cortex-M33.
The register CPUID reports value 0x490FDB00.
Reference link to the product:
Link: https://www.infineon.com/cms/en/about-infineon/press/market-news/2022/INFCSS202211-034.html
Change-Id: I8911712c55bd50e24ed53cf49958352f470027a5
Signed-off-by: Ahmed Boughanmi <boughanmi.external@infineon.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7879
Reviewed-by: Karl Palsson <karlp@tweak.au>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This patch adds error reporting when unknown image type is specified.
Previously, OpenOCD replied with an empty string.
Change-Id: I16220b1f5deb3b966a21731f0adf7911a78e8959
Signed-off-by: Marek Vrbka <marek.vrbka@codasip.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7883
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add a new riscv specific commands to disable triggers
Change-Id: Ic1842085aa66851c740e0abcbfbe0adbe930920e
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
Copy .travis.yml and tools/scripts/checkpatch.pl from upstream
ee31f1578a.
Addresses #913.
Change-Id: I69ad6b734ebf2cf7110010aa0481b6676124610e
Signed-off-by: Tim Newsome <tim@sifive.com>
If it fails, then pass that failure on. If it's simply not implemented,
then we can fall through and try target_get_gdb_reg_list_noread().
This difference matters when the target representing the current
hwthread is unavailable, but the target that is linked to the gdb
connection is available. In that case we want the operation to return an
error to gdb, instead of reading the register from the target that is
available.
Change-Id: I9c84ca556f818c5580e25ab349a34a226fcf0f43
Signed-off-by: Tim Newsome <tim@sifive.com>
When gdb requests to step an unavailable target, report success. When
the target becomes available, the step can complete.
Change-Id: I969ab56139f72a757552928d59edf6eabd598fa4
Signed-off-by: Tim Newsome <tim@sifive.com>
Extend riscv set_ebreak* commands.
Now it can be called without args to print current value.
riscv_ebreak* flags are moved to riscv_info struct.
Change-Id: Ib46e6b6dfc0117599c7f6715c7aaf113e63bd7dc
Signed-off-by: Kirill Radkin <kirill.radkin@syntacore.com>
Previously, the bcm2835_peri_base value would be printed as a decimal
value despite having a "0x" prefix, implying it should be a hex value.
BCM2835 GPIO: peripheral_base = 0x1056964608
Now, the value is correctly converted to hexidecimal.
BCM2835 GPIO: peripheral_base = 0x3F000000
Change-Id: Id59185423917e6350f99ef68320e2102a3192291
Fixes: b41b368255 ("jtag/drivers/bcm2835gpio: extend peripheral_base to off_t")
Signed-off-by: Vincent Fazio <vfazio@xes-inc.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7888
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
and DP_SELECT_DPBANK.
Use the defined symbols instead of magic numbers.
Change-Id: I19c86b183e57e42b96f76eed180c0492cd67bee1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7539
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
DP_SELECT_APSEL and DP_SELECT_APBANK is no more used in ADIv6.
Change-Id: I4176574d46c6dc8eb3fe3aef6daab6e33492c050
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/7538
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
add refresh command for lattice devices
rename gowin reprogram to refresh
rename virtex2 program to refresh
Change-Id: I9da83a614b96da3e947ac4608b0a291b1d126914
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7839
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide jtagspi with specific procedures to be able to
use jtagspi for programming spi-flash devices on cologne
chip gatemate devices.
Change-Id: Ifa1c4ca6e215d7f49bd21620898991af213812e9
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7838
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Provide jtagspi with information to use jtagspi for
programming spi-flash devices on intel devices using
a proxy bitstream.
Change-Id: Ib947b8c0dd61e2c6fa8beeb30074606131b1480f
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7837
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide jtagspi with information to use jtagspi for
programming spi-flash devices on xilinx devices
using a proxy bitstream.
Change-Id: I68000d71de25118ed8a8603e544cff1dc69bd9ba
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7836
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide jtagspi with information to use jtagspi for
programming spi-flash devices on efinix trion and
titanium devices using a proxy bitstream.
Change-Id: I4a851fcaafe832c35bd7b825d95a3d08e4d57a7b
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7826
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Provide jtagspi with specific procedures to be able to
use jtagspi for programming spi-flash devices on lattice
certus and certus po devices.
Change-Id: I6a8ec16be78f86073a4ef5302f6241185b08e1c6
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7825
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Provide jtagspi with specific procedures to be able to
use jtagspi for programming spi-flash devices on lattice
ecp5 devices.
Change-Id: I4a4a60f21d7e8685a5b8320b9c6ebdc2693bbd21
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7824
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Provide jtagspi with specific procedures to be able to
use jtagspi for programming spi-flash devices on lattice
ecp2 and ecp3 devices.
Change-Id: I39028aba47a74a0479be16d52d318f4bff7f2ed4
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7823
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Jtagspi is using a proxy bitstream to "connect" JTAG to the
SPI pins. This is not possible with all FPGA vendors/families.
In this cases a dedicated procedure is needed to establish such
a connection.
This patch adds a jtagspi-mode for these cases. It also adds the
needed interfaces to jtagspi and the pld-driver so the driver
can select the mode and provide the necessary procedures.
For the cases where a proxy bitstream is needed, the pld driver
will select the mode and provide instruction code needed in this
case.
Change-Id: I9563f26739589157b39a3664a73d91152cd13f77
Signed-off-by: Daniel Anselmi <danselmi@gmx.ch>
Reviewed-on: https://review.openocd.org/c/openocd/+/7822
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add support for the TI K3 family AM62P SoC. This SoC is built on the
same base of AM62A7, so reuse the configuration with the exception of
the JTAG ID and the actual name used for the R5 core (moved from main
domain to wakeup domain).
For further details, see https://www.ti.com/lit/pdf/spruj83
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I3a80be9e71204ed7697e51ac1ad488ef405744ef
Reviewed-on: https://review.openocd.org/c/openocd/+/7892
Reviewed-by: Bryan Brattlof <hello@bryanbrattlof.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Add support for the TI K3 family J784S4/AM69 SoC.
For further details, see http://www.ti.com/lit/zip/spruj52
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I3c899aed0cb79ab8bbf8077ca6dfe0636cf72288
Reviewed-on: https://review.openocd.org/c/openocd/+/7890
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
$_soc is set per platform, no point in duplicating _CHIPNAME to
explicitly set the information provided by $_CHIPNAME itself.
So move it out after the check for CHIP_NAME
Signed-off-by: Nishanth Menon <nm@ti.com>
Change-Id: I60d30d6a9a2ce352f66c5bc03075e4ba638e3062
Reviewed-on: https://review.openocd.org/c/openocd/+/7889
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
struct flash_bank must be zeroed anyway, calloc() is always used.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I7ab3b9c66f99688c6095a0a547a05448c9e37d68
Reviewed-on: https://review.openocd.org/c/openocd/+/7885
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
at91sam7 flash driver allocates a flash bank based on detected flash
structure.
Use calloc() instead of malloc() - struct flash_bank has to be zeroed.
While on this:
Return error in case of struct flash_bank or driver_priv allocation fail.
Set default_padded_value and erased_value.
Use strdup() on bank->name, pointer is freed in flash_free_all_banks()
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Id890496bfbadb7970ef583256aa4f30a7bff832f
Reviewed-on: https://review.openocd.org/c/openocd/+/7884
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
`riscv_debug_reg_to_s()` can be used to decode register value. If the
pointer to buffer is `NULL` it does not print anything, just returns the
length of the string.
The format is:
`<register_value> { <field_name>=<field_value_name or field_value>, ..., }`
e.g:
`0x400382 { version=2, ... ndmresetpending=false, }`
`0x321009 { regno=0x1009, ... cmdtype=0, }`
Change-Id: I63733d8d36385d89ca15de1a43139134bc488c4f
Signed-off-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
STM32WBA5x have a single bank flash up to 1MB
Change-Id: I3d720e202f0fdd89ecd8aa7224653ca5a7ae187b
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/7694
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Frank Plowman
Nishanth Menon
Dubravko Srsan
Parshintsev Anatoly
Artemiy Volkov
Antonio Borneo
liangzhen
Tim Newsome
Kirill Radkin
Ahmed Boughanmi
Marek Vrbka
Vincent Fazio
Peter Mamonov
Tomas Vanek
Daniel Anselmi
Evgeniy Naydanov
Tarek BOCHKATI