If fastdata access fails, then fallback to default mips_m4k_write_memory
Remove unnecessary fastdata loader verify check
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Don't save that state unless its only user, an assertion,
is compiled. Saving it broke a cygwin build.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Starting the daemon with with just a bare "openocd" I saw:
Can't find openocd.cfg
That's not an error; don't treat it as if it were. There may
be an error later -- like, "no interface set up" -- but let
messages only report real errors, not fake ones.
JTAG has only two possible JTAG ack codes for APACC and DPACC
register reads/writes. Define them, and remove empty "else"
clause in the code which now uses those codes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
I think some of these assumptions are not well-founded.
Related, that swjdp_transaction_endcheck() is a bit iffy.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
add reset-init script to allow ram execution from reset, this is required for ejtag fastdata access.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
The gdb_port command can be invoked during normal execution
to report the port used for gdb, whereas it was listed as
CONFIG stage only, which caused an error when excuting
it to return the reported error.
Also in line with the grander goal of making more commands
available during all "modes" (perhaps retiring config mode),
there is no particular reason to limit gdb_port to the
config stage.
Regression was introduced in:
b3bf1d12b2 aka
v0.4.0-rc1-32-gb3bf1d1
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
New versions of udev (148+) emit the following warnings:
udevd[425]: BUS= will be removed in a future udev version,
please use SUBSYSTEM= to match the event device, or
SUBSYSTEMS= to match a parent device, in /lib/udev/rules.d/60-openocd.rules:1
udevd[425]: SYSFS{}= will be removed in a future udev version,
please use ATTR{}= to match the event device, or
ATTRS{}= to match a parent device, in /lib/udev/rules.d/60-openocd.rules:4
udevd[425]: SYSFS{}= will be removed in a future udev version,
please use ATTR{}= to match the event device, or
ATTRS{}= to match a parent device, in /lib/udev/rules.d/60-openocd.rules:7
...
See also http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=560141
[dbrownell@users.sourceforge.net: add IDs for Stellaris ICDI, Olimex Tiny-H]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add doxyegen description for this driver.
Correct the helptext (configures *or* displays based on #params),
and usage (use the same BNF as the User's Guide).
Remove superfluous #include
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove superfluous #include.
Correct the helptext (configures *or* displays based on #params),
and usage (use the same BNF as the User's Guide).
Add doxygen -- file-level description and a @todo for doing
RTCK correctly.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The command processing conversion a while back lost the
"rtck" enable/disable command; restore it.
NOTE that having such a command is wrong; there's a standard
way to enable adaptive clocking ("speed 0").
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Build fixes: it failed abysmally with PPDEV enabled. Swapped
a build-time error with a FIXME comment in the affected macros.
Cleanup: remove "&" before function pointers, and excess indent,
for the interface struct declaration.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Rename DAP_IR_* as JTAG_DP_* since those symbols are specifically
for JTAG-DP (or SWJ-DP in JTAG mode), and won't work with SWD.
Define the JTAG ABORT and IDCODE instructions for completeness;
add a comment about where to (someday) use ABORT.
Fix messaging which assumes everything is an SWJ-DP; say "JTAG-DP"
instead, it's at least more appropriate for all JTAG transports.
Shrink the affected lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fix: don't print the BASE address except if it's a MEM-AP;
that's an unlikely error, but there's no point getting it wrong.
Tweaks: comments, capitalization.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make some private functions "static". Remove their public declarations,
and what is now an obviously unused function. Shrinks this object's size
(about 5% on x86_64) while making the code's scope easier to understand.
Shrink the affected lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Instead of magic numbers, use their AP_REG_* constants. Rename
the ROM address symbol as BASE to match ARM's documentation.
Comment various other symbols in the header; add some missing ones.
Remove an unused struct. Add some doxygen for stuff including the
DAP structure and initialization.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Shrink some lines, add some comments, simplify some tests.
During debug startup, log the core revision level too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most commands are usable only at runtime; so don't bother saying
that, it's noise. Moreover, tokens like EXEC are cryptic. Be
more clear: highlight only the commands which may (also) be used
during the config stage, thus matching the docs more closely.
There are
- Configuration commands (per documentation)
- And also some commands that valid at *any* time.
Update the docs to note that "help" now shows this mode info.
This also highlighted a few mistakes in command configuration,
mostly commands listed as "valid at any time" which shouldn't
have been. This just fixes ones I noted when sanity testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This makes it so that the usage/help command properly uses the whole command,
including subcommand, in the search for help information. This previously
caused erroneous output from the usage command handler.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
I wanted to make it so I can be ignorant of a commands invocation string, so
I tried to use CMD_CURRENT (aka cmd->current) which is supposed to house a
pointer to the current command. It turns out that this wasn't being set.
This patch adds the current command structure to the command invocation
structure before sending it along to the command handler.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The relevant cable config is already in OpenOCD, but not a config for
the JTAG adapter. I have tested with FlashLINK on ARM926.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This adds the .settings folder and the .cproject file put down
by Eclipse from the eyes of Git.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Handlers for commands
- arm7_9 semihosting <enable | disable>
- $_TARGETNAME arp_reset assert 1
didn't check if target has already been examined, and could
segfault when using the NULL pointer "arm7_9->eice_cache".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove useless space/tab at end of lines.
Remove spaces in indentation and replace with tab.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The handler for "arm9tdmi vector_catch ..." did not check
if target has already been examined. Without this fix it
segfaults when using NULL pointer "arm7_9->eice_cache".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Print "ssize_t" as "%ld" (+ cast to long) not as "%zu".
Official MinGW (gcc 3.4.5) doesn't understand "z" flag.
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most of this patch updates documentation and comments for various
Luminary boards, supporting two bug fixes by helping to make sense
of the current mess:
- Recent rev C lm3s811 eval boards didn't work. They must use
the ICDI layout, which sets up some signals that the older
boards didn't need. This is actually safe and appropriate
for *all* recent boards ... so just make "luminary.cfg" use
the ICDI layout.
- "luminary-lm3s811.cfg", was previously unusable! No VID/PID;
and the wrong vendor string. Make it work, but reserve it
for older boards where the ICDI layout is wrong.
- Default the LM3748 eval board to "luminary.cfg", like the
other boards. If someone uses an external JTAG adapter, all
boards will use the same workaround (override that default).
The difference between the two FT2232 layouts is that eventually
the EVB layout will fail cleanly when asked to enable SWO trace,
but the ICDI layout will as cleanly be able to enable it. Folk
using "luminary.cfg" with Rev B boards won't see anything going
wrong until SWO support is (someday) added.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Otherwise the new alignment checking algorithm thinks that the
address is not aligned, because it is way beyond the last sector.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This config is only lightly tested, and doesn't work well yet;
but it's a start.
* Notably missing is PLL configuration, since each DaVinci
does that just a bit differently; and thus DDR2 setup.
* The SRST workaround needed for the goof in the CPLD's VHDL
depends on at least the not-yet-merged patch letting ARM9
(and ARM7) chips perform resets that don't use SRST.
So this isn't yet suitable for debugging U-Boot.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Resolve a regression when using newish automagic "write_image"
modes, by always padding to the end of affected sectors.
Also document some issues associated with those automagic options,
in the User's Guide and also some related code comments.
We might need similar padding at the *beginning* of some sectors,
but this is a minimalist fix for the problems which have currently
been reported (plus doc updates).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The 10-pin JTAG layout used with these adapters is used by
a variety of platforms including AVR.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Spencer Oliver
David Brownell
David Claffey
Øyvind Harboe
Johannes Stezenbach
Dean Glazeski
Antonio Borneo
Piotr Esden-Tempski
Freddie Chopin
Catalin Patulea