These devices are essentially the same as the E54 series with the
exception of immutable boot (SG41, SG61) and HSM (SG60, SG61), and some
bug fixes found only in E54 revision F. When the security features are
not enabled, they behave identically except for the different DIDs.
Signed-off-by: Matt Trescott <mtc@melexis.com>
Change-Id: Ic93313f3e20af0ed4a5768880d17b335a7b7bb04
Reviewed-on: https://review.openocd.org/c/openocd/+/8355
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Use a command group 'telnet' with subcommands instead of individual
commands with 'telnet_' prefix. Even though there is only one subcommand
at the moment, make this change to ensure consistency with other commands.
The old command is still available to ensure backwards compatibility,
but are marked as deprecated.
Change-Id: I5e88632fa0d0ce5a8129e9fcf5ae743fc5b093cb
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8378
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The current semantics are a bit confusing, as the return value looks
like memcmp (0/false being equal) but the bool return type means one
likely expects true to mean equal. Make this clearer by switching them
out for buf_eq* functions that do that instead.
Checkpatch-ignore: UNSPECIFIED_INT
Change-Id: Iee0c5af794316aab5327cb9c168051fabd3bc1cb
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8490
Tested-by: jenkins
Reviewed-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Backtraces performed by GDB on any thread other than the current
thread would fail if hardware 8 byte ISR stack alignment
was enabled on cortex_m targets. Stack reads now adjust
the stored SP to account for a potential offset introduced by hardware.
Fixed incorrect register offsets for cortex_m Nuttx frames by reading
the TCB info symbols to determine correct offsets.
Fixed offsets can no longer be used since the offsets have changed
multiple times for different Nuttx versions.
Tested on nuttx-12.1.0.
Tested using custom stm32h7 board and custom s32k148 board variants.
Built with CONFIG_ARCH_FPU enabled and disabled to
test FPU and non FPU frame logic.
Change-Id: Ifcbeefb0ddcfbcb528daa9d1d95732ca9584c9ef
Signed-off-by: daniellizewski <daniellizewski@geotab.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8180
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
When a target is reset we must invalidate register caches in order
to avoid showing stale register values or writing them back to
registers. Use EDPRSR.SR to detect a previous reset, and EDPRSR.R to
detect a current reset state.
Change-Id: Ia1e97d7154cf7789d392274eee475733086a835b
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8425
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
This is the fast path for when there is a mismatch in the leading whole
bytes, which means we should return true to indicate not equal like all
the other cases here and in the surrounding functions. Otherwise we'll
incorrectly report _buf1 == _buf2 if and only if there are mismatches in
the leading whole bytes.
This was introduced during the refactor and optimisation referenced
below.
The only in-tree caller of this is jtag_check_value_inner, which will
just fail to catch some errors. However, downstream in riscv-openocd it
gets used in the riscv target to determine whether an IR scan is needed
to select the debug module, and with an IRLEN >= 8 this breaks resetting
if the encoding for the DMI isn't all-ones in its leading whole bytes
(to match BYPASS), since it will believe they are the same and not do an
IR scan, failing (with "At least one TAP shouldn't be in BYPASS mode")
in the subsequent DR scan due to the TAP still being recorded as having
bypass set (and really having an instruction of either BYPASS or
IDCODE).
Fixes: e4ee891759 ("improve buf_cmp and buf_cmp_mask helpers")
Change-Id: Ic4f7ed094429abc4c06a775eb847a8b3ddf2e2d6
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8489
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The README file contains a mixture of Markdown and non-Markdown syntax.
Refurbish the document and use only Markdown syntax according to the
specification in [1].
[1] https://www.markdownguide.org/
Change-Id: If58f4e2971dc798a03a78841226804ab1f2d33c8
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8387
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
- Xtensa LX8 is fully supported in addition to prior LX and NX cores.
Change-Id: I2f3f0a21ce1518b3ced6d241f0ab84c65af64423
Signed-off-by: Ian Thompson <ianst@cadence.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8362
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Current script does not enforces the check for the SPDX tag in the
linker scripts.
Add the extension '.ld' in the OpenOCD specific part.
Change-Id: I1cb6bc52e9dd86d99a26393085c7e2c9e8bac11f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8475
Tested-by: jenkins
Two different sizes uint8_t and uint32_t was used for this value
without a good reason.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I4bb60cc5397ffd0d37e7034e3930e62793140c8d
Reviewed-on: https://review.openocd.org/c/openocd/+/8439
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Tested-by: jenkins
Could be handy for dummy transfer size detection.
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ibb485218f6c2ff9066910bb58be0fc614b77add3
Reviewed-on: https://review.openocd.org/c/openocd/+/8438
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Use the TRAX interface DEBUGPC if available.
Otherwise use default stop-and-go profiling.
ESP32-S3, before this patch:
Internal: 8 samples/second
FT2232H: 12 samples/second
After this patch:
Internal: 18ksamples/second
FT2232H: 100ksamples/second
Change-Id: I681f0bccf4263c1e24f38be511e3b3aec8bf4d60
Signed-off-by: Richard Allen <rsaxvc@rsaxvc.net>
Reviewed-on: https://review.openocd.org/c/openocd/+/8431
Reviewed-by: Erhan Kurubas <erhan.kurubas@espressif.com>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Ian Thompson <ianst@cadence.com>
Reviewed-by: Yurii Shutkin <yurii.shutkin@gmail.com>
Simplify the code using the target endianness independent API.
Change-Id: I39f720d0db9cf24eb41d7f359e4321bbc2045658
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8474
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This adds support of TI LP-CC1352P7 evaluation kit.
For further details, see https://www.ti.com/tool/LP-CC1352P7.
Change-Id: I4aba160dbf4920febb7897458d06450e7d134147
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8194
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Vaishnav M A <vaishnav@beagleboard.org>
This adds support for TI CC13X2X7 / CC26X2X7 family.
For further details, see https://www.ti.com/lit/ug/swcu192/swcu192.pdf.
Change-Id: Ifd9b505716ddf0abbdd00f617e50a93a3d4fbe6a
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8193
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Vaishnav M A <vaishnav@beagleboard.org>
This updates the flash driver to support more than one bank.
This is required to support the cc1352p7 which has two banks.
This only have been tested on a cc1352p7.
The loader has been built using a gcc-arm-none-eabi-4_8-2014q3
toolchain.
Change-Id: Ia813421ececd96d6e2fd4dae910ad60fcc3d3c88
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8192
Tested-by: jenkins
Reviewed-by: Vaishnav M A <vaishnav@beagleboard.org>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Flash banks created in kinetis_create_missing_banks did not populate
bank->minimal_write_gap. The default value of 0 was interpreted as
FLASH_WRITE_CONTINUOUS. This created unnecessary large padding if your
binary had a gap in the populated flash. It also caused flash errors
when loading with GDB because the erroneously padded pages were not
erased first. Tested using an S32k148 using s32k.cfg.
Change-Id: I9b7af698e29ac2c4f5fc8ecd82fa7f4b1a0d43f1
Signed-off-by: daniellizewski <daniellizewski@geotab.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8463
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Sipeed USB-JTAG/TTL Debugger is a compact FT2232D-based JTAG adapter.
Change-Id: Ibc9075723f47cd9b49ba4bb39e3d292e7d80bed7
Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8472
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
When multiple jlink programmers are connected and no specific serial
or USB location is specified, print out the detected serial numbers.
Signed-off-by: Marcus Nilsson <brainbomb@gmail.com>
Change-Id: I280da2b85363f7054c5f466637120427cadcf7d1
Reviewed-on: https://review.openocd.org/c/openocd/+/8356
Reviewed-by: Mark Zhuang <mark.zhuang@spacemit.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Looks like 7f2d3e2925 introduced a regression by incorrectly assigning
threads. The title of the commit message says that the intention was to
"derive threadid from SMP index", this is not what happens, however.
Instead threadid is assigned based on an index of all examined targets
in an SMP group.
This introduces two logical errors.
*Error 1*
Here is the code that assigns threads to harts:
```
foreach_smp_target(head, target->smp_targets) {
struct target *curr = head->target;
if (!target_was_examined(curr))
continue;
threadid_t tid = threads_found + 1;
hwthread_fill_thread(rtos, curr, threads_found, tid);
```
Now, imagine a situation when we have two targets: `target.A` and
`target.B`. Let's assume that `target.A` is NOT examined (it could be
under reset, for example). Then, according to the algorithm when
assigning thread identifiers `target.B` will be assigned tid of 1. The
respected inferior on GDB side will be called `Thread 1`.
Now, imagine that `target.A` activates and succefully examined - OpenOCD
will re-assign thread identifiers. And now on GDB side `Thread 1` will
represent the state of `target.A`. Which is incorrect.
*Error 2*
The reverse mapping between `threadid` and targets does not take the
state of targets into account.
```
static struct target *
hwthread_find_thread(struct target *target, threadid_t thread_id)
...
threadid_t tid = 1;
foreach_smp_target(head, target->smp_targets) {
if (thread_id == tid)
head->target;
++tid;
}
```
So the constructed mapping is incorrect. Since in example above
`Thread 1` will get mapped to `target.A`.
*Solution:*
It seems that threadids should be assigned based on position of the
thread in an smp group disregarding the target state.
Change-Id: Ib93b7ed3bb03696afdf56a105b333e22b9ec69b5
Signed-off-by: Parshintsev Anatoly <anatoly.parshintsev@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8471
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Mark Zhuang <mark.zhuang@spacemit.com>
Tested-by: jenkins
Reviewed-by: Evgeniy Naydanov <evgeniy.naydanov@syntacore.com>
The _targets has to be global as it is accessed at the end of this file.
This is already the case for setup_a5x {}, assure it is the same way for
setup_crx{} . Without this change, the _targets at the end of this file
is empty in case the Cortex-R is the boot core, fix this.
Change-Id: I4979e3125ec7d93bbd56eee0096ae1d9c5f6a565
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8470
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
virtex2 refresh replaced virtex2 program, but the even older programming
commands like xc6s_program still suggest the old, now-removed program
command. This changes the warnings to suggest the command that is still
there, and also adds some indication that you will need to use the .pld
name instead of the .tap name.
Change-Id: I292da62a95a9b414c69cdb1bba8a28dfd16a7336
Signed-off-by: Adam Novak <interfect@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8468
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Daniel Anselmi <danselmi@gmx.ch>
If no mask is given, the value in the option register is replaced
completely. If a mask is set, only those bits that are set in the mask
are transferred into the option register; the others remain unchanged.
Change-Id: If488a10f92d7dcc0e0f192aef5e67c255fd529c3
Signed-off-by: Ondřej Hošek <ondra.hosek@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8466
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
stm32l4x option_write works like stm32h7x option_write, i.e. expects the
value to write after reg_offset and optionally reg_mask after the value.
Change-Id: I57fb4fb1dbf7f43fe063b48f4db2dd5f2ef0ade0
Signed-off-by: Ondřej Hošek <ondra.hosek@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8464
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Use mbstowcs() to get required length of wide character string and
include space for terminating null wide character.
Change-Id: I668de6f0acc9b3ec5aca033d870dd9ef354f9077
Signed-off-by: Marcus Nilsson <brainbomb@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8232
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Integer values are interpreted by TCL as decimal, binary, octal
or hexadecimal if prepended with '0d', '0b', '0o' or '0x'
respectively.
The case of '0' prefix has been interpreted as octal till TCL 8.6
but is interpreted as part of a decimal number by JimTCL and from
TCL 9.
Align str_to_buf() to latest TCL syntax by:
- addding support for '0d', '0b' and '0o' prefix;
- dropping support for '0' prefix.
Change-Id: I708ef72146d75b7bf429df329a0269cf48700a44
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8465
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Instead of making people type this in all the time, just default to
"SEGGER RTT" so more things work out of the box.
Change-Id: I147142cf0a755e635d3f66e047be2eb5049cf511
Signed-off-by: Karl Palsson <karl.palsson@marel.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8354
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Open output file in binary mode to disable EOL
conversion on Windows (and sometimes cygwin depending
on installation settings and path).
Change-Id: I38276dd1af011ce5781b0264b7cbb08c32a1a2ad
Signed-off-by: Richard Allen <rsaxvc@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8278
Reviewed-by: Karl Palsson <karlp@tweak.au>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
OpenOCD disables breakpoints on step/resume if they
match the current code position. This is a non-obvious
behavior that should be documented
Change-Id: Id762066569ec6452869a58dfcd9df88c8a14d6ab
Signed-off-by: Parshintsev Anatoly <anatoly.parshintsev@syntacore.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8388
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This is useful for setting a reset catch on a CPU that is being
brought out of reset.
Change-Id: Id8fe9bc3f75fd170f207f470a9f3b0faba7f24c1
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8422
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reduce the amount of boilerplate by moving cti_regs into its only
user, making it a local variable and removing the now-redundant
p_val pointer.
Change-Id: I778cc1e960532fae1ac1a952c6ff19c54e578a5f
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8421
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Some targets start up with the sticky overrun bit set. On such targets
we need to clear it in order to avoid subsequent incorrect reads.
Change-Id: I3e939a9e092de6fcea9494d3179a3386aa1701d2
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8420
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
While at it, fix some small coding style issues.
Change-Id: Ifb8e78b55d29a06d69a3ce71d12d0040777aef13
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8423
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The Linux checkpatch script used by OpenOCD reports hits either as
error, warning and check.
Such classification is meaningful for Linux maintainers, but for
OpenOCD Jenkins they are all considered as errors.
Having such classification in the checkpatch report by Jenkins is
misleading for developers that expect 'warnings' to be probably
ignored by maintainers, while having no idea what 'checks' means.
This patch flattens all the checkpatch reports to 'error' only.
Checkpatch can trigger false positives. OpenOCD uses the tag
Checkpatch-ignore:
in the commit message to prevent Jenkins to report the error, as
described in HACKING.
Change-Id: I1d3164ba1f725c0763dfe362192ffa669b3856e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8424
Reviewed-by: Karl Palsson <karlp@tweak.au>
Tested-by: jenkins
The function str_to_buf() can be simplified by writing directly
the intermediate results in the output buffer.
Such simplification improves the readability and also makes
scan-build happy, as it does not trigger anymore the warning:
src/helper/binarybuffer.c:328:8: warning: Use of memory
allocated with size zero [unix.Malloc]
if ((b256_buf[(buf_len / 8)] & mask) != 0x0) {
Change-Id: I1cef9a1ec5ff0e5841ba582610f273e89e7a81da
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8396
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Tested-by: jenkins
The name 'buf_len' is misleading, as it usually refers to the byte
length of a buffer. Here we use it for the length in bits.
Rename it as 'buf_bitsize'.
While there, fix checkpatch error by changing the index type to
'unsigned int'.
Change-Id: I78855ed79a346d996d9c0100d94d14c64a36b228
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8395
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
With 'radix' always zero and '_detected_radix' always NULL, drop
the two parameters and simplify str_to_buf().
While there:
- drop some redundant assert(),
- drop the re-check for the base prefix,
- simplify str_strip_number_prefix_if_present() and rename it, as
the prefix MUST be present,
- fix a minor typo,
- update the doxygen description of str_to_buf().
Change-Id: I1abdc8ec0587b23881953d3094101c04d5bb1c58
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8394
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Commit 53b94fad58 ("binarybuffer: Fix str_to_buf() parsing
function") introduces the helper command_parse_str_to_buf() to
parse as number a string on TCL command-line.
The parameter 'radix' can specify the base (decimal, octal,
hexadecimal, or auto-detected).
TCL is supposed to use decimal numbers by default, while octal and
hexadecimal numbers must be prefixed respectively with '0' and
'0x' (or '0X').
This would require the helper to always run auto-detection of the
base, thus always set the 'radix' parameter to zero. This makes
the parameter useless.
Keeping the 'radix' parameter can open the door to future abuse of
TCL syntax, E.g. a command can require an octal value without the
mandatory TCL '0' prefix; the octal value cannot be the result of
TCL expression.
To prevent any future abuse of the 'radix' parameter, drop it.
Change-Id: I88855bd83b4e08e8fdcf86a2fa5ef3269dd4ad57
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: https://review.openocd.org/c/openocd/+/8393
Tested-by: jenkins
Reviewed-by: Jan Matyas <jan.matyas@codasip.com>
Use correct TCL syntax and save string map operation.
Change-Id: Ic2a522bd57cf6610b7df1d9cddd0fbdc2076ed62
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: https://review.openocd.org/c/openocd/+/8426
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The telnet 'exit' command is only available in the execution phase of
OpenOCD. Thus, a telnet session cannot be closed via 'exit' if OpenOCD
is started with 'noinit'. Make the 'exit' command always available.
Change-Id: I14447ecde63e579f1c523d606f048ad29cc84a35
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: https://review.openocd.org/c/openocd/+/8379
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
Matt Trescott
Marc Schink
Evgeniy Naydanov
Jessica Clarke
daniellizewski
Peter Collingbourne
Ian Thompson
liangzhen
Antonio Borneo
Jiafei Pan
Tomas Vanek
Richard Allen
Parshintsev Anatoly
Alexandre Bailon
Jun Yan
Marcus Nilsson
Marek Vasut
Adam Novak
Ondřej Hošek
Karl Palsson
Richard Allen