- added support for Hitex STM32 Performance Stick

- added str9 and stm32 scripts to docs

git-svn-id: svn://svn.berlios.de/openocd/trunk@213 b42882b7-edfa-0310-969c-e2dbd0fdcd60

doc/openocd.texi

@@ -356,6 +356,8 @@ Luminary Micro EVB_LM3S811 as a JTAG interface (not onboard processor), no TRST
 SRST signals on external connector
 @item comstick
 Hitex STR9 comstick 
+@item stm32stick
+Hitex STM32 Performance Stick
 @end itemize
 
 @item @b{ft2232_vid_pid} <@var{vid}> <@var{pid}>
@@ -1181,6 +1183,46 @@ working_area 0 0x50000000 16384 nobackup
 flash bank str9x 0x00000000 0x00080000 0 0 0
 @end smallexample
 
+@section STR912 comstick
+@cindex STR912 comstick Script
+The following script was used with a Hitex STR9 Comstick:
+@smallexample
+#daemon configuration
+telnet_port 4444
+gdb_port 3333
+ 
+#interface
+interface ft2232
+ft2232_device_desc "STR9-comStick A"
+ft2232_layout comstick
+jtag_speed 1
+
+jtag_nsrst_delay 100
+jtag_ntrst_delay 100
+
+#use combined on interfaces or targets that can't set TRST/SRST separately
+reset_config trst_and_srst
+ 
+#jtag scan chain
+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
+jtag_device 8 0x1 0x1 0xfe
+jtag_device 4 0x1 0xf 0xe
+jtag_device 5 0x1 0x1 0x1e
+ 
+#target configuration
+daemon_startup reset
+ 
+#target <type> <startup mode>
+#target arm966e <endianness> <reset mode> <chainpos> <variant>
+target arm966e little reset_halt 1 arm966e
+run_and_halt_time 0 30
+ 
+working_area 0 0x50000000 16384 nobackup
+ 
+#flash bank <driver> <base> <size> <chip_width> <bus_width>
+flash bank str9x 0x00000000 0x00080000 0 0 0
+@end smallexample
+
 @section STM32x Script
 @cindex STM32x Script
 The following script was used with an Amontec JTAGkey and a STM32x cpu:
@@ -1195,6 +1237,9 @@ ft2232_device_desc "Amontec JTAGkey A"
 ft2232_layout jtagkey
 jtag_speed 10
 
+jtag_nsrst_delay 100
+jtag_ntrst_delay 100
+
 #use combined on interfaces or targets that can't set TRST/SRST separately
 reset_config trst_and_srst
  
@@ -1217,6 +1262,46 @@ working_area 0 0x20000000 16384 nobackup
 flash bank stm32x 0x08000000 0x00010000 0 0 0
 @end smallexample
 
+@section STM32x Performance Stick
+@cindex STM32x Performance Stick Script
+The following script was used with the Hitex STM32 Performance Stick
+@smallexample
+#daemon configuration
+telnet_port 4444
+gdb_port 3333
+ 
+#interface
+interface ft2232
+ft2232_device_desc "STM32-PerformanceStick A"
+ft2232_layout stm32stick
+jtag_speed 10
+
+jtag_nsrst_delay 100
+jtag_ntrst_delay 100
+
+#use combined on interfaces or targets that can't set TRST/SRST separately
+reset_config trst_and_srst
+ 
+#jtag scan chain
+#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
+jtag_device 4 0x1 0xf 0xe
+jtag_device 5 0x1 0x1 0x1e
+jtag_device 4 0x1 0xf 0xe
+ 
+#target configuration
+daemon_startup reset
+ 
+#target <type> <startup mode>
+#target cortex_m3 <endianness> <reset mode> <chainpos> <variant>
+target cortex_m3 little run_and_halt 0
+run_and_halt_time 0 30
+ 
+working_area 0 0x20000000 16384 nobackup
+ 
+#flash bank <driver> <base> <size> <chip_width> <bus_width>
+flash bank stm32x 0x08000000 0x00010000 0 0 0
+@end smallexample
+
 @section  LPC2294 Script
 @cindex  LPC2294 Script
 The following script was used with an Amontec JTAGkey and a LPC2294 cpu:

src/jtag/ft2232.c

@@ -100,6 +100,7 @@ int olimex_jtag_init(void);
 int flyswatter_init(void);
 int turtle_init(void);
 int comstick_init(void);
+int stm32stick_init(void);
 
 /* reset procedures for supported layouts */
 void usbjtag_reset(int trst, int srst);
@@ -108,6 +109,7 @@ void olimex_jtag_reset(int trst, int srst);
 void flyswatter_reset(int trst, int srst);
 void turtle_reset(int trst, int srst);
 void comstick_reset(int trst, int srst);
+void stm32stick_reset(int trst, int srst);
 
 /* blink procedures for layouts that support a blinking led */
 void olimex_jtag_blink(void);
@@ -125,6 +127,7 @@ ft2232_layout_t ft2232_layouts[] =
 	{"flyswatter", flyswatter_init, flyswatter_reset, NULL},
 	{"turtelizer2", turtle_init, turtle_reset, turtle_jtag_blink},
 	{"comstick", comstick_init, comstick_reset, NULL},
+	{"stm32stick", stm32stick_init, stm32stick_reset, NULL},
 	{NULL, NULL, NULL},
 };
 
@@ -1073,6 +1076,39 @@ void comstick_reset(int trst, int srst)
 	DEBUG("trst: %i, srst: %i, high_output: 0x%2.2x, high_direction: 0x%2.2x", trst, srst, high_output, high_direction);
 }
 
+void stm32stick_reset(int trst, int srst)
+{
+	if (trst == 1)
+	{
+		cur_state = TAP_TLR;
+		high_output &= ~nTRST;
+	}
+	else if (trst == 0)
+	{
+		high_output |= nTRST;
+	}
+
+    if (srst == 1)
+    {
+        low_output &= ~nSRST;
+    }
+    else if (srst == 0)
+    {
+        low_output |= nSRST;
+    }
+	
+	/* command "set data bits low byte" */
+	BUFFER_ADD = 0x80;
+	BUFFER_ADD = low_output;
+	BUFFER_ADD = low_direction;
+	
+	/* command "set data bits high byte" */
+	BUFFER_ADD = 0x82;
+	BUFFER_ADD = high_output;
+	BUFFER_ADD = high_direction;
+	DEBUG("trst: %i, srst: %i, high_output: 0x%2.2x, high_direction: 0x%2.2x", trst, srst, high_output, high_direction);
+}
+
 int ft2232_execute_queue()
 {
 	jtag_command_t *cmd = jtag_command_queue; /* currently processed command */
@@ -1916,6 +1952,49 @@ int comstick_init(void)
 	return ERROR_OK;
 }
 
+int stm32stick_init(void)
+{
+	u8 buf[3];
+	u32 bytes_written;
+	
+	low_output = 0x88;
+	low_direction = 0x8b;
+	
+	/* initialize low byte for jtag */
+	buf[0] = 0x80; /* command "set data bits low byte" */
+	buf[1] = low_output; /* value (TMS=1,TCK=0, TDI=0, nOE=0) */
+	buf[2] = low_direction; /* dir (output=1), TCK/TDI/TMS=out, TDO=in, nOE=out */
+	DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
+	
+	if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+	{
+		ERROR("couldn't initialize FT2232 with 'stm32stick' layout"); 
+		return ERROR_JTAG_INIT_FAILED;
+	}
+		
+	nTRST = 0x01;
+	nTRSTnOE = 0x00; /* no output enable for nTRST */
+	nSRST = 0x80;
+	nSRSTnOE = 0x00; /* no output enable for nSRST */
+  	
+	high_output = 0x01;
+	high_direction = 0x03;
+	
+	/* initialize high port */
+	buf[0] = 0x82; /* command "set data bits high byte" */
+	buf[1] = high_output;
+	buf[2] = high_direction;
+	DEBUG("%2.2x %2.2x %2.2x", buf[0], buf[1], buf[2]);
+	
+	if (((ft2232_write(buf, 3, &bytes_written)) != ERROR_OK) || (bytes_written != 3))
+	{
+		ERROR("couldn't initialize FT2232 with 'stm32stick' layout"); 
+		return ERROR_JTAG_INIT_FAILED;
+	}
+	
+	return ERROR_OK;
+}
+
 void olimex_jtag_blink(void)
 {
 	/* Olimex ARM-USB-OCD has a LED connected to ACBUS3